Hi folks,
every boot of my kernels fail after enabling SEP.
This happened with 2.5.58, 2.5.59, 2.5.60. 2.5.62 (I haven't tested
2.5.61)
After a tip I tested 2.5.40 and it boots (although there were some kbd.c
issues, but it is a eraly kernel anway, I would look forward to look if
it happend with .6x too, but I need to get the box started for that;) )
I also have tested it only on my laptop as my main box is a little
server too, so I wouldn't experiment with kernels there...
Log, lspci output and .config without comments and empty lines follows:
[...]
PCI: Probing PCI Hardware (bus 00)
Transparent Bridge - Intel Corp. 82801BAM/CAM PCI Bri
ACPI: Power Resoirce [PFAN] (off)
Linux Plug and Play Support v0.94 (c) Adam Belay
pnp: Enabling Plug and Play Card Services.
PnPBIOS: Found PnP BIOS installation structure at 0xc00f0440
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x9138, desg 0x0
PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by driver
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
block request queues:
128 requests per read queue
128 requests per write queue
8 requests per batch
enter congestion at 15
exit congestion at 17
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
PCI: using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi" or even 'acpi=off'
Enabling SEP on CPU 0
<noting, system halts>
I tried with pci=noacpi and that didn't do it. Well, it displays one
screen with green lines from the upper to the lower and halts then. I
don't think this is good for my LCD display ;)
The system:
Toshiba Satelite 2410-304S, Mobile P4 2Ghz
frodo:~# lspci
00:00.0 Host bridge: Intel Corp. 82845 845 (Brookdale) Chipset Host
Bridge (rev 04)
00:01.0 PCI bridge: Intel Corp. 82845 845 (Brookdale) Chipset AGP Bridge
(rev 04)
00:1d.0 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #1) (rev 02)
00:1d.1 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #2) (rev 02)
00:1e.0 PCI bridge: Intel Corp. 82801BAM/CAM PCI Bridge (rev 42)
00:1f.0 ISA bridge: Intel Corp. 82801CAM ISA Bridge (LPC) (rev 02)
00:1f.1 IDE interface: Intel Corp. 82801CAM IDE U100 (rev 02)
00:1f.5 Multimedia audio controller: Intel Corp. 82801CA/CAM AC'97 Audio
(rev 02)
00:1f.6 Modem: Intel Corp. 82801CA/CAM AC'97 Modem (rev 02)
01:00.0 VGA compatible controller: nVidia Corporation NV17 [GeForce4 420
Go] (rev a3)
02:07.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A
IEEE-1394a-2000 Controller (PHY/Link)
02:08.0 Ethernet controller: Intel Corp. 82801CAM (ICH3) PRO/100 VE
(LOM) Ethernet Controller (rev 42)
02:0a.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus
Controller (rev 01)
02:0b.0 CardBus bridge: Toshiba America Info Systems ToPIC95 PCI to
Cardbus Bridge with ZV Support (rev 32)
02:0b.1 CardBus bridge: Toshiba America Info Systems ToPIC95 PCI to
Cardbus Bridge with ZV Support (rev 32)
02:0d.0 System peripheral: Toshiba America Info Systems SD TypA
Controller (rev 03)
frodo:~#
frodo:/usr/src/linux-2.5.62# less .config | grep -v ^# | grep ^C
CONFIG_X86=y
CONFIG_MMU=y
CONFIG_SWAP=y
CONFIG_UID16=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_EXPERIMENTAL=y
CONFIG_SYSVIPC=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_SYSCTL=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_OBSOLETE_MODPARM=y
CONFIG_KMOD=y
CONFIG_X86_PC=y
CONFIG_MPENTIUM4=y
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_L1_CACHE_SHIFT=7
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_TSC=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_PREFETCH=y
CONFIG_X86_SSE2=y
CONFIG_X86_MCE=y
CONFIG_X86_MCE_NONFATAL=y
CONFIG_TOSHIBA=y
CONFIG_EDD=y
CONFIG_NOHIGHMEM=y
CONFIG_MTRR=y
CONFIG_PM=y
CONFIG_SOFTWARE_SUSPEND=y
CONFIG_ACPI=y
CONFIG_ACPI_BOOT=y
CONFIG_ACPI_SLEEP=y
CONFIG_ACPI_SLEEP_PROC_FS=y
CONFIG_ACPI_AC=y
CONFIG_ACPI_BATTERY=y
CONFIG_ACPI_BUTTON=y
CONFIG_ACPI_FAN=y
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_THERMAL=y
CONFIG_ACPI_TOSHIBA=y
CONFIG_ACPI_DEBUG=y
CONFIG_ACPI_BUS=y
CONFIG_ACPI_INTERPRETER=y
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_PCI=y
CONFIG_ACPI_SYSTEM=y
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_PROC_INTF=y
CONFIG_CPU_FREQ_TABLE=y
CONFIG_X86_SPEEDSTEP=y
CONFIG_PCI=y
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_NAMES=y
CONFIG_ISA=y
CONFIG_HOTPLUG=y
CONFIG_PCMCIA=y
CONFIG_CARDBUS=y
CONFIG_KCORE_ELF=y
CONFIG_BINFMT_AOUT=y
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=y
CONFIG_PARPORT=y
CONFIG_PARPORT_PC=y
CONFIG_PARPORT_PC_CML1=y
CONFIG_PARPORT_1284=y
CONFIG_PNP=y
CONFIG_PNP_NAMES=y
CONFIG_PNP_CARD=y
CONFIG_ISAPNP=y
CONFIG_PNPBIOS=y
CONFIG_BLK_DEV_FD=y
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_SIZE=4096
CONFIG_BLK_DEV_INITRD=y
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
CONFIG_BLK_DEV_IDECD=y
CONFIG_BLK_DEV_IDESCSI=y
CONFIG_BLK_DEV_CMD640=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_BLK_DEV_GENERIC=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
CONFIG_IDEDMA_PCI_AUTO=y
CONFIG_BLK_DEV_IDEDMA=y
CONFIG_BLK_DEV_ADMA=y
CONFIG_BLK_DEV_PIIX=y
CONFIG_BLK_DEV_RZ1000=y
CONFIG_IDEDMA_AUTO=y
CONFIG_BLK_DEV_IDE_MODES=y
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
CONFIG_BLK_DEV_SR=y
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=y
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_AIC7XXX=y
CONFIG_AIC7XXX_CMDS_PER_DEVICE=64
CONFIG_AIC7XXX_RESET_DELAY_MS=2000
CONFIG_AIC7XXX_DEBUG_MASK=0
CONFIG_AIC7XXX_REG_PRETTY_PRINT=y
CONFIG_SCSI_QLOGIC_1280=y
CONFIG_IEEE1394=y
CONFIG_IEEE1394_OHCI1394=y
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IPV6_SCTP__=y
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
CONFIG_NET_ETHERNET=y
CONFIG_NET_PCI=y
CONFIG_E100=y
CONFIG_PPP=y
CONFIG_PPP_MULTILINK=y
CONFIG_PPP_ASYNC=y
CONFIG_PPP_SYNC_TTY=y
CONFIG_PPP_DEFLATE=y
CONFIG_PPPOE=y
CONFIG_NET_PCMCIA=y
CONFIG_PCMCIA_PCNET=y
CONFIG_NET_PCMCIA_RADIO=y
CONFIG_PCMCIA_RAYCS=y
CONFIG_INPUT=y
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
CONFIG_SOUND_GAMEPORT=y
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_CORE=y
CONFIG_UNIX98_PTYS=y
CONFIG_UNIX98_PTY_COUNT=256
CONFIG_PRINTER=y
CONFIG_INTEL_RNG=y
CONFIG_AGP=y
CONFIG_AUTOFS4_FS=y
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
CONFIG_JBD=y
CONFIG_JBD_DEBUG=y
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_CRAMFS=y
CONFIG_TMPFS=y
CONFIG_RAMFS=y
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_MINIX_FS=y
CONFIG_NTFS_FS=y
CONFIG_PROC_FS=y
CONFIG_DEVPTS_FS=y
CONFIG_ROMFS_FS=y
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_UDF_FS=y
CONFIG_NFS_FS=y
CONFIG_SUNRPC=y
CONFIG_LOCKD=y
CONFIG_SMB_FS=y
CONFIG_FS_MBCACHE=y
CONFIG_FS_POSIX_ACL=y
CONFIG_MSDOS_PARTITION=y
CONFIG_SMB_NLS=y
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_ISO8859_1=y
CONFIG_FB=y
CONFIG_FB_VGA16=y
CONFIG_FB_VESA=y
CONFIG_FB_RIVA=y
CONFIG_VGA_CONSOLE=y
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_PCI_CONSOLE=y
CONFIG_FONTS=y
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
CONFIG_SOUND=y
CONFIG_SND=y
CONFIG_SND_SEQUENCER=y
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=y
CONFIG_SND_PCM_OSS=y
CONFIG_SND_SEQUENCER_OSS=y
CONFIG_SND_INTEL8X0=y
CONFIG_SOUND_PRIME=y
CONFIG_SOUND_ICH=y
CONFIG_USB=y
CONFIG_USB_DEVICEFS=y
CONFIG_USB_BANDWIDTH=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_UHCI_HCD=y
CONFIG_USB_ACM=y
CONFIG_USB_PRINTER=y
CONFIG_USB_STORAGE=y
CONFIG_USB_SCANNER=y
CONFIG_USB_SERIAL=y
CONFIG_USB_SERIAL_KEYSPAN=y
CONFIG_USB_SERIAL_KEYSPAN_USA19QW=y
CONFIG_USB_EZUSB=y
CONFIG_DEBUG_KERNEL=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_KALLSYMS=y
CONFIG_DEBUG_SPINLOCK_SLEEP=y
CONFIG_FRAME_POINTER=y
CONFIG_CRC32=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_X86_BIOS_REBOOT=y
frodo:/usr/src/linux-2.5.62#
Regards,
Rene
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Sun Feb 23 2003 - 22:00:23 EST