On Fri, 21 Mar 2003, Justin T. Gibbs wrote:
> > Hi Justin i got this booting 2.5.65-mm2, 2.5.65 was fine there is an oops
> > right at the end. Is there anything specific you want?
>
> It would be nice to know the devices that are attached to the controller.
> Could you also use the latest driver from here:
This is from a 2.4.18-RH kernel
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.5
<Adaptec aic7870 SCSI adapter>
aic7870: Wide Channel A, SCSI Id=7, 16/253 SCBs
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.5
<Adaptec aic7870 SCSI adapter>
aic7870: Wide Channel A, SCSI Id=7, 16/253 SCBs
Vendor: DEC Model: DLT2000 Rev: 830A
Type: Sequential-Access ANSI SCSI revision: 02
Vendor: TOSHIBA Model: CD-ROM XM-5401TA Rev: 3605
Type: CD-ROM ANSI SCSI revision: 02
Vendor: SEAGATE Model: ST15150W Rev: 9103
Type: Direct-Access ANSI SCSI revision: 02
Vendor: SEAGATE Model: ST15150W Rev: 9103
Type: Direct-Access ANSI SCSI revision: 02
Vendor: SEAGATE Model: ST15150W Rev: 9103
Type: Direct-Access ANSI SCSI revision: 02
Vendor: SEAGATE Model: ST15150W Rev: 9103
Type: Direct-Access ANSI SCSI revision: 02
Vendor: SEAGATE Model: ST15150W Rev: 9103
Type: Direct-Access ANSI SCSI revision: 02
Vendor: SEAGATE Model: ST15150W Rev: 9103
Type: Direct-Access ANSI SCSI revision: 02
scsi1:A:0:0: Tagged Queuing enabled. Depth 253
scsi1:A:1:0: Tagged Queuing enabled. Depth 253
scsi1:A:2:0: Tagged Queuing enabled. Depth 253
scsi1:A:3:0: Tagged Queuing enabled. Depth 253
scsi1:A:4:0: Tagged Queuing enabled. Depth 253
scsi1:A:5:0: Tagged Queuing enabled. Depth 253
Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
Attached scsi disk sdb at scsi1, channel 0, id 1, lun 0
Attached scsi disk sdc at scsi1, channel 0, id 2, lun 0
Attached scsi disk sdd at scsi1, channel 0, id 3, lun 0
Attached scsi disk sde at scsi1, channel 0, id 4, lun 0
Attached scsi disk sdf at scsi1, channel 0, id 5, lun 0
(scsi1:A:0): 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
SCSI device sda: 8388315 512-byte hdwr sectors (4295 MB)
Partition check:
sda: sda1
(scsi1:A:1): 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
SCSI device sdb: 8388315 512-byte hdwr sectors (4295 MB)
sdb: sdb1 sdb2
(scsi1:A:2): 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
SCSI device sdc: 8388315 512-byte hdwr sectors (4295 MB)
sdc: sdc1
(scsi1:A:3): 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
SCSI device sdd: 8388315 512-byte hdwr sectors (4295 MB)
sdd: sdd1
(scsi1:A:4): 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
SCSI device sde: 8388315 512-byte hdwr sectors (4295 MB)
sde: sde1
(scsi1:A:5): 20.000MB/s transfers (10.000MHz, offset 8, 16bit)
SCSI device sdf: 8388315 512-byte hdwr sectors (4295 MB)
sdf: sdf1
> http://people.FreeBSD.org/~gibbs/linux/SRC/
I'll try that driver this evening.
> the driver and send me the output you get.
Thanks,
Zwane
-- function.linuxpower.ca - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Sun Mar 23 2003 - 22:00:39 EST