Hello,
I have first tried to boot it with the ZIP in the drive, but without
sucess :-(
Now, I have booted without a disk in the drive, and only got those
errors:
Uniform Multi-Platform E-IDE driver Revision: 7.00beta3-.2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 00:1f.1
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
hda: IC35L120AVVA07-0, ATA DISK drive
hdb: IOMEGA ZIP 250 ATAPI, ATAPI FLOPPY drive
blk: queue c03d3760, I/O limit 4095Mb (mask 0xffffffff)
hdc: SONY DVD RW DRU-500A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 241254720 sectors (123522 MB) w/1863KiB Cache, CHS=15017/255/63, UDMA(100)
hdb: attached ide-scsi driver.
hdc: attached ide-scsi driver.
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 p6 >
hdb:<3>ide-scsi: hdb: unsupported command in request queue (0)
end_request: I/O error, dev 03:40 (hdb), sector 0
ide-scsi: hdb: unsupported command in request queue (0)
end_request: I/O error, dev 03:40 (hdb), sector 2
ide-scsi: hdb: unsupported command in request queue (0)
end_request: I/O error, dev 03:40 (hdb), sector 4
ide-scsi: hdb: unsupported command in request queue (0)
end_request: I/O error, dev 03:40 (hdb), sector 6
ide-scsi: hdb: unsupported command in request queue (0)
end_request: I/O error, dev 03:40 (hdb), sector 0
ide-scsi: hdb: unsupported command in request queue (0)
end_request: I/O error, dev 03:40 (hdb), sector 2
ide-scsi: hdb: unsupported command in request queue (0)
end_request: I/O error, dev 03:40 (hdb), sector 4
ide-scsi: hdb: unsupported command in request queue (0)
end_request: I/O error, dev 03:40 (hdb), sector 6
unable to read partition table
SCSI subsystem driver Revision: 1.00
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.28
...
SCSI device sdb: 71687370 512-byte hdwr sectors (36704 MB)
/dev/scsi/host0/bus0/target15/lun0: p1 p2
sdc : READ CAPACITY failed.
sdc : status = 0, message = 00, host = 0, driver = 28
Current sd00:00: sns = 70 2
ASC=3a ASCQ= 0
Raw sense data:0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x12 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00 0xff 0xfe 0x01 0x03 0x31 0x01 0xce 0x5a
sdc : block size assumed to be 512 bytes, disk size 1GB.
/dev/scsi/host2/bus0/target0/lun0: I/O error: dev 08:20, sector 0
I/O error: dev 08:20, sector 0
unable to read partition table
I have an MSI Max2-BLR.
I don't know which other info I should send for this problem?
Grégoire
________________________________________________________________
http://ulima.unil.ch/greg ICQ:16624071 mailto:greg@ulima.unil.ch
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Wed Apr 30 2003 - 22:00:32 EST