On Fri, 2003-05-09 at 13:55, Andy Pfiffer wrote:
> On Fri, 2003-05-09 at 13:04, Christophe Saout wrote:
> > Am Fre, 2003-05-09 um 21.04 schrieb Andy Pfiffer:
> >
> > > [...]
> > > I had an unrelated
> > > delay in posting this due to some strange behavior of late with LILO and
> > > my ext3-mounted /boot partition (/sbin/lilo would say that it updated,
> > > but a subsequent reboot would not include my new kernel)
> >
> > So I'm not the only one having this problem... I think I first saw this
> > with 2.5.68 but I'm not sure.
>
> Well, that makes two of us for sure.
>
> >
> > My boot partition is a small ext3 partition on a lvm2 volume accessed
> > over device-mapper (I've written a lilo patch for that, but the patch is
> > working and) but I don't think that has something to do with the
> > problem.
> >
> > When syncing, unmounting and waiting some time after running lilo, the
> > changes sometimes seem correctly written to disk, I don't know when
> > exactly.
>
> My /boot is an ext3 partition on an IDE disk. My symptoms and your
> symptoms match -- wait awhile, and it works okay. If you don't wait
> "long enough" the changes made in /etc/lilo.conf are not reflected in
> the after running /sbin/lilo and rebooting normally.
>
> I have been unable to reproduce this on a uniproc system with SCSI
> disks.
>
> 2.5.67 seems to work in this regard as expected.
>
> > Could it be that the location of /boot/map is not written to the
> > partition sector of /dev/hda? Or not flushed correctly or something?
> >
> > After reboot the old kernel came up again (though it was moved to
> > vmlinuz.old).
>
> I don't know -- I haven't isolated it yet.
>
> Anyone else?
I have taken another look at this, and can confirm the following:
1. 2.5.67 works as expected.
2. 2.5.68, 2.5.69, and 2.5.70 do not.
3. ext2 vs. ext3 for /boot: no effect (ie, .68, .69, .70 demonstrate the
problem independent of the filesystem used for /boot).
Relative to a 2.5.68 pure BK tree, the deltas from 2.5.67 to 2.5.68 are:
1.971.76.10 /* 2.5.67 */
1.1124 /* 2.5.68 */
The patch exported by BK between these 2 revs is 297K lines ( a sizeable
haystack ). Any ideas about where I should dig for my needle first
would be welcomed...
Gory details about my hardware & software follow...
% lilo -v
LILO version 22.1, Copyright (C) 1992-1998 Werner Almesberger
Development beyond version 21 Copyright (C) 1999-2001 John Coffman
Released 31-Oct-2001 and compiled at 20:50:13 on Mar 25 2002.
MAX_IMAGES = 27
CPUs:
processor : 0
vendor_id : GenuineIntel
cpu family : 15
model : 1
model name : Intel(R) Xeon(TM) CPU 1.70GHz
stepping : 2
cpu MHz : 1685.926
cache size : 256 KB
physical id : 0
siblings : 1
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov
pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm
bogomips : 3317.76
processor : 1
vendor_id : GenuineIntel
cpu family : 15
model : 0
model name : Intel(R) Xeon(TM) CPU 1700MHz
stepping : 10
cpu MHz : 1685.926
cache size : 256 KB
physical id : 0
siblings : 1
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov
pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm
bogomips : 3366.91
Two IDE hard drives (I haven't cracked the case to identify the
manufacturer):
/dev/hda:
HDIO_GETGEO_BIG failed: Inappropriate ioctl for device
Model=CI530L04VARE700- , FwRev=REO44AA5,
SerialNo= S PXXTYH2351
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=40
BuffType=DualPortCache, BuffSize=1916kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=78156288
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255)
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-2 ATA-3 ATA-4
ATA-5
/dev/hdb:
HDIO_GETGEO_BIG failed: Inappropriate ioctl for device
Model=CI530L02VARE700- , FwRev=REO24AA5,
SerialNo= S PVVTFT0B17
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=40
BuffType=DualPortCache, BuffSize=1916kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=39876480
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255)
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-2 ATA-3 ATA-4
ATA-5
The PCI hardware on this system:
00:00.0 Host bridge: Intel Corp. 82850 860 (Wombat) Chipset Host Bridge
(MCH) (rev 04)
Subsystem: IBM: Unknown device 2531
Flags: bus master, fast devsel, latency 0
Memory at f0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
00:01.0 PCI bridge: Intel Corp. 82850/82860 850/860 (Tehama/Wombat)
Chipset AGP Bridge (rev 04) (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, fast devsel, latency 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Memory behind bridge: f6000000-f8ffffff
Prefetchable memory behind bridge: f4000000-f5ffffff
00:02.0 PCI bridge: Intel Corp. 82860 860 (Wombat) Chipset PCI Bridge
(rev 04) (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, fast devsel, latency 32
Bus: primary=00, secondary=02, subordinate=03, sec-latency=0
Memory behind bridge: fb000000-fb0fffff
00:1e.0 PCI bridge: Intel Corp. 82801BA/CA PCI Bridge (rev 04) (prog-if
00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: f9000000-faffffff
00:1f.0 ISA bridge: Intel Corp. 82801BA ISA Bridge (LPC) (rev 04)
Flags: bus master, medium devsel, latency 0
00:1f.1 IDE interface: Intel Corp. 82801BA IDE U100 (rev 04) (prog-if 80
[Master])
Subsystem: IBM: Unknown device 2442
Flags: bus master, medium devsel, latency 0
I/O ports at f000 [size=16]
00:1f.2 USB Controller: Intel Corp. 82801BA/BAM USB (Hub (rev 04)
(prog-if 00 [UHCI])
Subsystem: IBM: Unknown device 2442
Flags: bus master, medium devsel, latency 0, IRQ 19
I/O ports at d000 [size=32]
00:1f.3 SMBus: Intel Corp. 82801BA/BAM SMBus (rev 04)
Subsystem: IBM: Unknown device 2442
Flags: medium devsel, IRQ 17
I/O ports at 5000 [size=16]
00:1f.5 Multimedia audio controller: Intel Corp. 82801BA/BAM AC'97 Audio
(rev 04)
Subsystem: IBM: Unknown device 0224
Flags: bus master, medium devsel, latency 0, IRQ 17
I/O ports at d800 [size=256]
I/O ports at dc00 [size=64]
01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G400 AGP
(rev 85) (prog-if 00 [VGA])
Subsystem: Matrox Graphics, Inc. Millennium G450 Dual Head
Flags: bus master, medium devsel, latency 64, IRQ 22
Memory at f4000000 (32-bit, prefetchable) [size=32M]
Memory at f6000000 (32-bit, non-prefetchable) [size=16K]
Memory at f7000000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Capabilities: [f0] AGP version 2.0
02:1f.0 PCI bridge: Intel Corp. 82806AA PCI64 Hub PCI Bridge (rev 03)
(prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, fast devsel, latency 0
Bus: primary=02, secondary=03, subordinate=03, sec-latency=32
Memory behind bridge: fb000000-fb0fffff
03:00.0 PIC: Intel Corp. 82806AA PCI64 Hub Advanced Programmable
Interrupt Controller (rev 01) (prog-if 20 [IO(X)-APIC])
Subsystem: Intel Corp. 82806AA PCI64 Hub Advanced Programmable
Interrupt Controller
Flags: bus master, fast devsel, latency 0
Memory at fb000000 (32-bit, non-prefetchable) [size=4K]
04:04.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100]
(rev 0c)
Subsystem: IBM: Unknown device 0207
Flags: bus master, medium devsel, latency 32, IRQ 16
Memory at fa020000 (32-bit, non-prefetchable) [size=4K]
I/O ports at c000 [size=64]
Memory at fa000000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [dc] Power Management version 2
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
This archive was generated by hypermail 2b29 : Sun Jun 15 2003 - 22:00:30 EST