Re: Radeonfb problem
From: Damian Kolkowski
Date: Wed Feb 18 2004 - 05:36:49 EST
* Benjamin Herrenschmidt <benh@xxxxxxxxxxxxxxxxxxx> [2004-02-18 00:02]:
> Ugh ? Send me a dmesg log at boot please without any command
> line. radeonfb should set your display to the native panel size
> by default
Ups.., I forget too attache dmesg.
--
# Damian *dEiMoS* Kołkowski # http://kolkowski.no-ip.org/ #
Linux version 2.6.3-mm1 (root@uran) (gcc version 3.3.3) #1 Wed Feb 18 10:52:03 CET 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
BIOS-e820: 000000000fff0000 - 000000000fff3000 (ACPI NVS)
BIOS-e820: 000000000fff3000 - 0000000010000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
255MB LOWMEM available.
found SMP MP-table at 000f55b0
zapping low mappings.
On node 0 totalpages: 65520
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 61424 pages, LIFO batch:14
HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
ACPI: RSDP (v000 VKT400 ) @ 0x000f7070
ACPI: RSDT (v001 VKT400 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0fff3000
ACPI: FADT (v001 VKT400 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0fff3040
ACPI: MADT (v001 VKT400 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0fff6f80
ACPI: DSDT (v001 VKT400 AWRDACPI 0x00001000 MSFT 0x0100000d) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0])
IOAPIC[0]: Assigned apic_id 2
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, IRQ 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 dfl dfl)
ACPI BALANCE SET
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Initializing CPU#0
Kernel command line: BOOT_IMAGE=Slackware-NEW ro root=305 hdc=ide-scsi mem=nopentium
ide_setup: hdc=ide-scsi
PID hash table entries: 1024 (order 10: 8192 bytes)
Detected 1795.740 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Memory: 255816k/262080k available (1680k kernel code, 5528k reserved, 509k data, 332k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3538.94 BogoMIPS
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383fbf7 c1c3fbff 00000000 00000020
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Athlon(tm) XP 2200+ stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1794.0545 MHz.
..... host bus clock speed is 265.0858 MHz.
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb3a0, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040211
IOAPIC[0]: Set PCI routing entry (2-9 -> 0x71 -> IRQ 9 Mode:1 Active:1)
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [ALKA] (IRQs 20)
ACPI: PCI Interrupt Link [ALKB] (IRQs 21)
ACPI: PCI Interrupt Link [ALKC] (IRQs 22)
ACPI: PCI Interrupt Link [ALKD] (IRQs 23)
SCSI subsystem initialized
IOAPIC[0]: Set PCI routing entry (2-16 -> 0xa9 -> IRQ 16 Mode:1 Active:1)
00:00:08[A] -> 2-16 -> IRQ 16
IOAPIC[0]: Set PCI routing entry (2-17 -> 0xb1 -> IRQ 17 Mode:1 Active:1)
00:00:08[B] -> 2-17 -> IRQ 17
IOAPIC[0]: Set PCI routing entry (2-18 -> 0xb9 -> IRQ 18 Mode:1 Active:1)
00:00:08[C] -> 2-18 -> IRQ 18
IOAPIC[0]: Set PCI routing entry (2-19 -> 0xc1 -> IRQ 19 Mode:1 Active:1)
00:00:08[D] -> 2-19 -> IRQ 19
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
_CRS returns NULL! Using IRQ 21 fordevice (PCI Interrupt Link [ALKB]).
ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
IOAPIC[0]: Set PCI routing entry (2-21 -> 0xc9 -> IRQ 21 Mode:1 Active:1)
00:00:10[A] -> 2-21 -> IRQ 21
Pin 2-21 already programmed
Pin 2-21 already programmed
Pin 2-21 already programmed
_CRS returns NULL! Using IRQ 20 fordevice (PCI Interrupt Link [ALKA]).
ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
IOAPIC[0]: Set PCI routing entry (2-20 -> 0xd1 -> IRQ 20 Mode:1 Active:1)
00:00:11[A] -> 2-20 -> IRQ 20
Pin 2-21 already programmed
_CRS returns NULL! Using IRQ 22 fordevice (PCI Interrupt Link [ALKC]).
ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
IOAPIC[0]: Set PCI routing entry (2-22 -> 0xd9 -> IRQ 22 Mode:1 Active:1)
00:00:11[C] -> 2-22 -> IRQ 22
_CRS returns NULL! Using IRQ 23 fordevice (PCI Interrupt Link [ALKD]).
ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 23
IOAPIC[0]: Set PCI routing entry (2-23 -> 0xe1 -> IRQ 23 Mode:1 Active:1)
00:00:11[D] -> 2-23 -> IRQ 23
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-23 already programmed
Pin 2-23 already programmed
Pin 2-23 already programmed
Pin 2-23 already programmed
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178003
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0003
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 0 1 0 1 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 001 01 1 1 0 1 0 1 1 A9
11 001 01 1 1 0 1 0 1 1 B1
12 001 01 1 1 0 1 0 1 1 B9
13 001 01 1 1 0 1 0 1 1 C1
14 001 01 1 1 0 1 0 1 1 D1
15 001 01 1 1 0 1 0 1 1 C9
16 001 01 1 1 0 1 0 1 1 D9
17 001 01 1 1 0 1 0 1 1 E1
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9-> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ20 -> 0:20
IRQ21 -> 0:21
IRQ22 -> 0:22
IRQ23 -> 0:23
.................................... done.
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
radeonfb: Found Intel x86 BIOS ROM Image
radeonfb: Retreived PLL infos from BIOS
radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=250.00 Mhz, System=200.00 MHz
radeonfb: Monitor 1 type CRT found
radeonfb: EDID probed
radeonfb: Monitor 2 type no found
Monitor Operating Limits: From EDID
H: 30-86KHz V: 50-160Hz DCLK: 180MHz
radeonfb: ATI Radeon If DDR SGRAM 64 MB
Machine check exception polling timer started.
Initializing Cryptographic API
PCI: Via IRQ fixup for 0000:00:10.0, from 11 to 5
PCI: Via IRQ fixup for 0000:00:10.1, from 11 to 5
PCI: Via IRQ fixup for 0000:00:10.2, from 10 to 5
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Fan [FAN] (on)
ACPI: Processor [CPU0] (supports C1 C2)
ACPI: Thermal Zone [THRM] (40 C)
Console: switching to colour frame buffer device 80x30
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA KT400/KT400A/KT600 chipset
agpgart: Maximum main memory to use for agp memory: 203M
agpgart: AGP aperture is 128M @ 0xd0000000
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
ide0: BM-DMA at 0xdc00-0xdc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xdc08-0xdc0f, BIOS settings: hdc:DMA, hdd:pio
hda: Maxtor 6E040L0, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: HL-DT-ST GCE-8480B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 80293248 sectors (41110 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(133)
hda: hda1 hda2 < hda5 hda6 >
Console: switching to colour frame buffer device 80x30
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: ImExPS/2 Logitech Explorer Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
i2c /dev entries driver
oprofile: using NMI interrupt.
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
NET: Registered protocol family 1
NET: Registered protocol family 17
BIOS EDD facility v0.12 2004-Jan-26, 1 devices found
Please report your BIOS at http://linux.dell.com/edd/results.html
ACPI: (supports S0 S1 S4 S5)
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device hda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (hda5) for (hda5)
Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 332k freed
Adding 248968k swap on /dev/hda6. Priority:-1 extents:1
blk: queue c13a0400, I/O limit 4095Mb (mask 0xffffffff)
via-rhine.c:v1.10-LK1.1.19-2.5 July-12-2003 Written by Donald Becker
http://www.scyld.com/network/via-rhine.html
eth0: VIA VT6102 Rhine-II at 0xe800, 00:0a:e6:3e:7e:13, IRQ 23.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
ide-scsi is deprecated for cd burning! Use ide-cd and give dev=/dev/hdX as device
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: HL-DT-ST Model: CD-RW GCE-8480B Rev: 1.03
Type: CD-ROM ANSI SCSI revision: 02
[drm] Initialized radeon 1.10.0 20020828 on minor 0: ATI Radeon If R250 9000
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
ehci_hcd 0000:00:10.3: EHCI Host Controller
ehci_hcd 0000:00:10.3: irq 21, pci mem d1928000
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.3: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
Via 686a/8233/8235 audio driver 1.9.1-ac4-2.5
via82cxxx: Six channel audio available
PCI: Setting latency timer of device 0000:00:11.5 to 64
ac97_codec: AC97 Audio codec, id: VIA97 (Unknown)
via82cxxx: board #1 at 0xE000, IRQ 22
eth0: Setting full-duplex based on MII #1 link partner capability of 45e1.
smbfs: Unrecognized mount option noexec