2.4.26: ACPI error messages on Intel S875WP1-E mainboard
From: Meelis Roos
Date: Sun May 09 2004 - 08:04:51 EST
I get the following ACPI error messages on Intel S875WP1-E mainboard
with stock Linux 2.4.26. 2.4.27-pre2 gives the same errors.
2.6.6-rc3-bk10 doesn't give any errors, although it also has the
20040326 ACPI release.
ACPI-1133: *** Error: Method execution failed [\GPRW] (Node f7e70400), AE_NOT_EXIST
ACPI-1133: *** Error: Method execution failed [\_SB_.PCI0.P0P2.TANA._PRW] (Node f7e70d80), AE_NOT_EXIST
ACPI-0154: *** Error: Method execution failed [\_SB_.PCI0.P0P2.TANA._PRW] (Node f7e70d80), AE_NOT_EXIST
These messages do not seem to disturb anything, the computer is running
fine.
And this is the full dmesg:
Linux version 2.4.26-elevant1 (mroos@uusvant) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 SMP Sun May 9 13:13:57 EEST 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fe30000 (usable)
BIOS-e820: 000000003fe30000 - 000000003fe414aa (ACPI NVS)
BIOS-e820: 000000003fe414aa - 000000003ff30000 (usable)
BIOS-e820: 000000003ff30000 - 000000003ff40000 (ACPI data)
BIOS-e820: 000000003ff40000 - 000000003fff0000 (ACPI NVS)
BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved)
BIOS-e820: 00000000fecf0000 - 00000000fecf1000 (reserved)
BIOS-e820: 00000000fed20000 - 00000000feda0000 (reserved)
Warning only 896MB will be used.
Use a HIGHMEM enabled kernel.
896MB LOWMEM available.
found SMP MP-table at 000ff780
hm, page 000ff000 reserved twice.
hm, page 00100000 reserved twice.
hm, page 000fc000 reserved twice.
hm, page 000fd000 reserved twice.
On node 0 totalpages: 229376
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 ACPIAM ) @ 0x000f61a0
ACPI: RSDT (v001 INTEL S875PWP4 0x20040205 MSFT 0x00000097) @ 0x3ff30000
ACPI: FADT (v002 INTEL S875PWP4 0x20040205 MSFT 0x00000097) @ 0x3ff30200
ACPI: MADT (v001 INTEL S875PWP4 0x20040205 MSFT 0x00000097) @ 0x3ff30300
ACPI: WDDT (v001 INTEL OEMWDDT 0x00000001 MSFT 0x0100000d) @ 0x3ff345c0
ACPI: DSDT (v001 INTEL S875PWP4 0x00000001 MSFT 0x0100000d) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 Pentium 4(tm) XEON(tm) APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 Pentium 4(tm) XEON(tm) APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0])
IOAPIC[0]: Assigned apic_id 2
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, IRQ 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Using ACPI (MADT) for SMP configuration information
Kernel command line: auto BOOT_IMAGE=Linux ro root=900
Initializing CPU#0
Detected 2793.073 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 5570.56 BogoMIPS
Memory: 904528k/917504k available (1468k kernel code, 12588k reserved, 610k data, 128k init, 0k highmem)
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 262144 (order: 8, 1048576 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@xxxxxxxxxxxxx)
mtrr: detected mtrr type: Intel
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
CPU0: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
per-CPU timeslice cutoff: 1462.56 usecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Booting processor 1/1 eip 3000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 5583.66 BogoMIPS
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
Intel machine check reporting enabled on CPU#1.
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
CPU1: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
Total of 2 processors activated (11154.22 BogoMIPS).
cpu_sibling_map[0] = 1
cpu_sibling_map[1] = 0
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2793.1070 MHz.
..... host bus clock speed is 199.5075 MHz.
cpu: 0, clocks: 1995075, slice: 665025
CPU0<T0:1995072,T1:1330016,D:31,S:665025,C:1995075>
cpu: 1, clocks: 1995075, slice: 665025
CPU1<T0:1995072,T1:665008,D:14,S:665025,C:1995075>
checking TSC synchronization across CPUs: passed.
Waiting on wait_init_idle (map = 0x2)
All processors have done init_idle
ACPI: Subsystem revision 20040326
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=3
PCI: Using configuration type 1
ACPI-1133: *** Error: Method execution failed [\GPRW] (Node f7e70400), AE_NOT_EXIST
ACPI-1133: *** Error: Method execution failed [\_SB_.PCI0.P0P2.TANA._PRW] (Node f7e70d80), AE_NOT_EXIST
ACPI-0154: *** Error: Method execution failed [\_SB_.PCI0.P0P2.TANA._PRW] (Node f7e70d80), AE_NOT_EXIST
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: System [ACPI] (supports S0 S1 S4 S5)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
Transparent bridge - Intel Corp. 82801BA/CA/DB/EB PCI Bridge
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
PCI: Probing PCI hardware
IOAPIC[0]: Set PCI routing entry (2-16 -> 0xa9 -> IRQ 16 Mode:1 Active:1)
00:00:02[A] -> 2-16 -> IRQ 16
IOAPIC[0]: Set PCI routing entry (2-17 -> 0xb1 -> IRQ 17 Mode:1 Active:1)
00:00:1f[B] -> 2-17 -> IRQ 17
IOAPIC[0]: Set PCI routing entry (2-18 -> 0xb9 -> IRQ 18 Mode:1 Active:1)
00:00:1f[A] -> 2-18 -> IRQ 18
IOAPIC[0]: Set PCI routing entry (2-19 -> 0xc1 -> IRQ 19 Mode:1 Active:1)
00:00:1d[B] -> 2-19 -> IRQ 19
IOAPIC[0]: Set PCI routing entry (2-23 -> 0xc9 -> IRQ 23 Mode:1 Active:1)
00:00:1d[D] -> 2-23 -> IRQ 23
IOAPIC[0]: Set PCI routing entry (2-20 -> 0xd1 -> IRQ 20 Mode:1 Active:1)
00:03:08[A] -> 2-20 -> IRQ 20
IOAPIC[0]: Set PCI routing entry (2-21 -> 0xd9 -> IRQ 21 Mode:1 Active:1)
00:03:00[A] -> 2-21 -> IRQ 21
IOAPIC[0]: Set PCI routing entry (2-22 -> 0xe1 -> IRQ 22 Mode:1 Active:1)
00:03:00[B] -> 2-22 -> IRQ 22
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 003 03 0 0 0 0 0 1 1 39
02 003 03 0 0 0 0 0 1 1 31
03 003 03 0 0 0 0 0 1 1 41
04 003 03 0 0 0 0 0 1 1 49
05 003 03 0 0 0 0 0 1 1 51
06 003 03 0 0 0 0 0 1 1 59
07 003 03 0 0 0 0 0 1 1 61
08 003 03 0 0 0 0 0 1 1 69
09 003 03 0 1 0 0 0 1 1 71
0a 003 03 0 0 0 0 0 1 1 79
0b 003 03 0 0 0 0 0 1 1 81
0c 003 03 0 0 0 0 0 1 1 89
0d 003 03 0 0 0 0 0 1 1 91
0e 003 03 0 0 0 0 0 1 1 99
0f 003 03 0 0 0 0 0 1 1 A1
10 003 03 1 1 0 1 0 1 1 A9
11 003 03 1 1 0 1 0 1 1 B1
12 003 03 1 1 0 1 0 1 1 B9
13 003 03 1 1 0 1 0 1 1 C1
14 003 03 1 1 0 1 0 1 1 D1
15 003 03 1 1 0 1 0 1 1 D9
16 003 03 1 1 0 1 0 1 1 E1
17 003 03 1 1 0 1 0 1 1 C9
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ20 -> 0:20
IRQ21 -> 0:21
IRQ22 -> 0:22
IRQ23 -> 0:23
.................................... done.
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
Journalled Block Device driver loaded
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Processor [CPU1] (supports C1, 8 throttling states)
ACPI: Processor [CPU2] (supports C1, 8 throttling states)
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ DETECT_IRQ SERIAL_PCI enabled
keyboard: Timeout - AT keyboard not present?(ed)
keyboard: Timeout - AT keyboard not present?(f4)
ttyS00 at 0x03f8 (irq = 4) is a 16550A
Real Time Clock Driver v1.10f
Non-volatile memory driver v1.2
i810_rng hardware driver 0.9.8 loaded
hw_random: misc device register failed
i810 TCO timer, v0.05: timer margin: 30 sec (0x0460) (nowayout=0)
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
NET4: Frame Diverter 0.46
Intel(R) PRO/1000 Network Driver - version 5.2.30.1-k1
Copyright (c) 1999-2004 Intel Corporation.
PCI: Setting latency timer of device 02:01.0 to 64
divert: allocating divert_blk for eth0
eth0: Intel(R) PRO/1000 Network Connection
Intel(R) PRO/100 Network Driver - version 2.3.38-k1
Copyright (c) 2004 Intel Corporation
divert: allocating divert_blk for eth1
e100: selftest OK.
e100: eth1: Intel(R) PRO/100 Network Connection
Hardware receive checksums enabled
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 816M
agpgart: Unsupported Intel chipset (device id: 2578), you might want to boot with agp=try_unsupported
agpgart: no supported devices found.
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH5: IDE controller at PCI slot 00:1f.1
PCI: Enabling device 00:1f.1 (0005 -> 0007)
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
ICH5-SATA: IDE controller at PCI slot 00:1f.2
ICH5-SATA: chipset revision 2
ICH5-SATA: 100% native mode on irq 18
ide2: BM-DMA at 0xdc00-0xdc07, BIOS settings: hde:DMA, hdf:pio
ide3: BM-DMA at 0xdc08-0xdc0f, BIOS settings: hdg:DMA, hdh:pio
hdc: SAMSUNG CD-ROM SC-152A, ATAPI CD/DVD-ROM drive
hde: WDC WD800JD-00HKA0, ATA DISK drive
hdf: probing with STATUS(0x00) instead of ALTSTATUS(0x50)
hdf: probing with STATUS(0x00) instead of ALTSTATUS(0x50)
blk: queue c0380f78, I/O limit 4095Mb (mask 0xffffffff)
hdg: WDC WD800JD-00HKA0, ATA DISK drive
hdh: probing with STATUS(0x00) instead of ALTSTATUS(0x50)
hdh: probing with STATUS(0x00) instead of ALTSTATUS(0x50)
blk: queue c03813e4, I/O limit 4095Mb (mask 0xffffffff)
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0xec00-0xec07,0xe802 on irq 18
ide3 at 0xe400-0xe407,0xe002 on irq 18
hde: attached ide-disk driver.
hde: host protected area => 1
hde: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=155061/16/63, UDMA(33)
hdg: attached ide-disk driver.
hdg: host protected area => 1
hdg: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=155061/16/63, UDMA(33)
hdc: attached ide-cdrom driver.
hdc: ATAPI 52X CD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.12
Partition check:
hde: hde1 hde2 hde3
hdg: hdg1 hdg2 hdg3
Promise Fasttrak(tm) Softwareraid driver 0.03beta: No raid array found
mice: PS/2 mouse device common for all mice
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
8regs : 3201.600 MB/sec
32regs : 2496.000 MB/sec
pIII_sse : 3653.200 MB/sec
pII_mmx : 3238.800 MB/sec
p5_mmx : 3347.600 MB/sec
raid5: using function: pIII_sse (3653.200 MB/sec)
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
[events: 00128d3b]
[events: 000270f7]
[events: 00128d3b]
[events: 000270f7]
md: autorun ...
md: considering hdg3 ...
md: adding hdg3 ...
md: adding hde3 ...
md: created md1
md: bind<hde3,1>
md: bind<hdg3,2>
md: running: <hdg3><hde3>
md: hdg3's event counter: 000270f7
md: hde3's event counter: 000270f7
md: md1: raid array is not clean -- starting background reconstruction
md: RAID level 1 does not need chunksize! Continuing anyway.
md1: max total readahead window set to 124k
md1: 1 data-disks, max readahead per data-disk: 124k
raid1: device hdg3 operational as mirror 1
raid1: device hde3 operational as mirror 0
raid1: raid set md1 not clean; reconstructing mirrors
raid1: raid set md1 active with 2 out of 2 mirrors
md: syncing RAID array md1
md: minimum _guaranteed_ reconstruction speed: 100 KB/sec/disc.
md: using maximum available idle IO bandwith (but not more than 100000 KB/sec) for reconstruction.
md: using 124k window, over a total of 54713664 blocks.
md: updating md1 RAID superblock on device
md: hdg3 [events: 000270f8]<6>(write) hdg3's sb offset: 54713664
md: hde3 [events: 000270f8]<6>(write) hde3's sb offset: 54713664
md: considering hdg1 ...
md: adding hdg1 ...
md: adding hde1 ...
md: created md0
md: bind<hde1,1>
md: bind<hdg1,2>
md: running: <hdg1><hde1>
md: hdg1's event counter: 00128d3b
md: hde1's event counter: 00128d3b
md: md0: raid array is not clean -- starting background reconstruction
md: RAID level 1 does not need chunksize! Continuing anyway.
md0: max total readahead window set to 124k
md0: 1 data-disks, max readahead per data-disk: 124k
raid1: device hdg1 operational as mirror 1
raid1: device hde1 operational as mirror 0
raid1: raid set md0 not clean; reconstructing mirrors
raid1: raid set md0 active with 2 out of 2 mirrors
md: delaying resync of md0 until md1 has finished resync (they share one or more physical units)
md: updating md0 RAID superblock on device
md: hdg1 [events: 00128d3c]<6>(write) hdg1's sb offset: 19530880
md: hde1 [events: 00128d3c]<6>(write) hde1's sb offset: 19530880
md: ... autorun DONE.
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 128k freed
Adding Swap: 2097136k swap-space (priority -1)
Adding Swap: 2097136k swap-space (priority -2)
SCSI subsystem driver Revision: 1.00
EXT3 FS 2.4-0.9.19, 19 August 2002 on md(9,0), internal journal
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 13:17:23 May 9 2004
usb-uhci.c: High bandwidth mode enabled
PCI: Setting latency timer of device 00:1d.0 to 64
usb-uhci.c: USB UHCI at I/O 0xcc00, IRQ 16
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.1 to 64
usb-uhci.c: USB UHCI at I/O 0xd000, IRQ 19
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.2 to 64
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 18
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.3 to 64
usb-uhci.c: USB UHCI at I/O 0xd800, IRQ 16
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@xxxxxxx>
hid-core.c: USB HID support drivers
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on md(9,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
PCI: Setting latency timer of device 00:1d.7 to 64
ehci_hcd 00:1d.7: Intel Corp. 82801EB USB2
ehci_hcd 00:1d.7: irq 23, pci mem f8a72c00
usb.c: new USB bus registered, assigned bus number 5
ehci_hcd 00:1d.7: enabled 64bit PCI DMA
PCI: cache line size of 128 is not supported by device 00:1d.7
ehci_hcd 00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
hub.c: USB hub found
hub.c: 8 ports detected
e1000: eth0 NIC Link is Up 100 Mbps Full Duplex
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
md: md1: sync done.
md: syncing RAID array md0
md: minimum _guaranteed_ reconstruction speed: 100 KB/sec/disc.
md: using maximum available idle IO bandwith (but not more than 100000 KB/sec) for reconstruction.
md: using 124k window, over a total of 19530880 blocks.
md: md0: sync done.
--
Meelis Roos (mroos@xxxxxxxx)
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/