[7/15] orinoco merge preliminaries - comment/whitespace/spelling updates
From: David Gibson
Date: Wed Jul 28 2004 - 02:48:06 EST
Various trivial cleanups to the orinoco driver: whitespace changes,
spelling/capitalization errors corrected, some fairly insignificant
comments added, removed or reformatted.
Signed-off-by: David Gibson <hermes@xxxxxxxxxxxxxxxxxxxxx>
Index: working-2.6/drivers/net/wireless/orinoco.c
===================================================================
--- working-2.6.orig/drivers/net/wireless/orinoco.c 2004-07-28 14:57:52.310664496 +1000
+++ working-2.6/drivers/net/wireless/orinoco.c 2004-07-28 14:57:53.046552624 +1000
@@ -59,7 +59,7 @@
* o Add PM timeout (holdover duration)
* o Enable "iwconfig eth0 key off" and friends (toggle flags)
* o Enable "iwconfig eth0 power unicast/all" (toggle flags)
- * o Try with an intel card. It report firmware 1.01, behave like
+ * o Try with an Intel card. It report firmware 1.01, behave like
* an antiquated firmware, however on windows it says 2.00. Yuck !
* o Workaround firmware bug in allocate buffer (Intel 1.01)
* o Finish external renaming to orinoco...
@@ -69,8 +69,8 @@
* o Update to Wireless 11 -> add retry limit/lifetime support
* o Tested with a D-Link DWL 650 card, fill in firmware support
* o Warning on Vcc mismatch (D-Link 3.3v card in Lucent 5v only slot)
- * o Fixed the Prims2 WEP bugs that I introduced in v0.03 :-(
- * It work on D-Link *only* after a tcpdump. Weird...
+ * o Fixed the Prism2 WEP bugs that I introduced in v0.03 :-(
+ * It works on D-Link *only* after a tcpdump. Weird...
* And still doesn't work on Intel card. Grrrr...
* o Update the mode after a setport3
* o Add preamble setting for Symbol cards (not yet enabled)
@@ -106,7 +106,7 @@
* o Remove deferred power enabling code
*
* v0.05c -> v0.05d - 5/5/2001 - Jean II
- * o Workaround to SNAP decapsulate frame from LinkSys AP
+ * o Workaround to SNAP decapsulate frame from Linksys AP
* original patch from : Dong Liu <dliu AT research.bell-labs.com>
* (note : the memcmp bug was mine - fixed)
* o Remove set_retry stuff, no firmware support it (bloat--).
@@ -135,15 +135,15 @@
*
* v0.06c -> v0.06d - 6/7/2001 - David Gibson
* o Change a bunch of KERN_INFO messages to KERN_DEBUG, as per Linus'
- * wishes to reduce the number of unecessary messages.
+ * wishes to reduce the number of unnecessary messages.
* o Removed bogus message on CRC error.
- * o Merged fixeds for v0.08 Prism 2 firmware from William Waghorn
+ * o Merged fixes for v0.08 Prism 2 firmware from William Waghorn
* <willwaghorn AT yahoo.co.uk>
* o Slight cleanup/re-arrangement of firmware detection code.
*
* v0.06d -> v0.06e - 1/8/2001 - David Gibson
* o Removed some redundant global initializers (orinoco_cs.c).
- * o Added some module metadataa
+ * o Added some module metadata
*
* v0.06e -> v0.06f - 14/8/2001 - David Gibson
* o Wording fix to license
@@ -173,7 +173,7 @@
* o Turned has_big_wep on for Intersil cards. That's not true for all of
* them but we should at least let the capable ones try.
* o Wait for BUSY to clear at the beginning of hermes_bap_seek(). I
- * realised that my assumption that the driver's serialization
+ * realized that my assumption that the driver's serialization
* would prevent the BAP being busy on entry was possibly false, because
* things other than seeks may make the BAP busy.
* o Use "alternate" (oui 00:00:00) encapsulation by default.
@@ -182,12 +182,12 @@
* o Don't try to make __initdata const (the version string). This can't
* work because of the way the __initdata sectioning works.
* o Added MODULE_LICENSE tags.
- * o Support for PLX (transparent PCMCIA->PCI brdge) cards.
- * o Changed to using the new type-facist min/max.
+ * o Support for PLX (transparent PCMCIA->PCI bridge) cards.
+ * o Changed to using the new type-fascist min/max.
*
* v0.08 -> v0.08a - 9/10/2001 - David Gibson
* o Inserted some missing acknowledgements/info into the Changelog.
- * o Fixed some bugs in the normalisation of signel level reporting.
+ * o Fixed some bugs in the normalization of signal level reporting.
* o Fixed bad bug in WEP key handling on Intersil and Symbol firmware,
* which led to an instant crash on big-endian machines.
*
@@ -343,7 +343,7 @@
* o Bugfix in orinoco_stop() - it used to fail if hw_unavailable
* was set, which was usually true on PCMCIA hot removes.
* o Track LINKSTATUS messages, silently drop Tx packets before
- * we are connected (avoids cofusing the firmware), and only
+ * we are connected (avoids confusing the firmware), and only
* give LINKSTATUS printk()s if the status has changed.
*
* v0.13b -> v0.13c - 11 Mar 2003 - David Gibson
@@ -398,7 +398,8 @@
* o Disconnect wireless extensions from fundamental configuration.
* o (maybe) Software WEP support (patch from Stano Meduna).
* o (maybe) Use multiple Tx buffers - driver handling queue
- * rather than firmware. */
+ * rather than firmware.
+ */
/* Locking and synchronization:
*
@@ -415,7 +416,8 @@
* flag after taking the lock, and if it is set, give up on whatever
* they are doing and drop the lock again. The orinoco_lock()
* function handles this (it unlocks and returns -EBUSY if
- * hw_unavailable is non-zero). */
+ * hw_unavailable is non-zero).
+ */
#include <linux/config.h>
@@ -495,9 +497,10 @@
HERMES_MAX_MULTICAST : 0)*/
#define MAX_MULTICAST(priv) (HERMES_MAX_MULTICAST)
-#define ORINOCO_INTEN ( HERMES_EV_RX | HERMES_EV_ALLOC | HERMES_EV_TX | \
- HERMES_EV_TXEXC | HERMES_EV_WTERR | HERMES_EV_INFO | \
- HERMES_EV_INFDROP )
+#define ORINOCO_INTEN (HERMES_EV_RX | HERMES_EV_ALLOC \
+ | HERMES_EV_TX | HERMES_EV_TXEXC \
+ | HERMES_EV_WTERR | HERMES_EV_INFO \
+ | HERMES_EV_INFDROP )
/********************************************************************/
/* Data tables */
@@ -510,7 +513,8 @@
};
#define NUM_CHANNELS ARRAY_SIZE(channel_frequency)
-/* This tables gives the actual meanings of the bitrate IDs returned by the firmware. */
+/* This tables gives the actual meanings of the bitrate IDs returned
+ * by the firmware. */
struct {
int bitrate; /* in 100s of kilobits */
int automatic;
@@ -574,8 +578,7 @@
/* Internal helper functions */
/********************************************************************/
-static inline void
-set_port_type(struct orinoco_private *priv)
+static inline void set_port_type(struct orinoco_private *priv)
{
switch (priv->iw_mode) {
case IW_MODE_INFRA:
@@ -640,16 +643,14 @@
return err;
}
-struct net_device_stats *
-orinoco_get_stats(struct net_device *dev)
+struct net_device_stats *orinoco_get_stats(struct net_device *dev)
{
struct orinoco_private *priv = netdev_priv(dev);
return &priv->stats;
}
-struct iw_statistics *
-orinoco_get_wireless_stats(struct net_device *dev)
+struct iw_statistics *orinoco_get_wireless_stats(struct net_device *dev)
{
struct orinoco_private *priv = netdev_priv(dev);
hermes_t *hw = &priv->hw;
@@ -707,8 +708,7 @@
return wstats;
}
-static void
-orinoco_set_multicast_list(struct net_device *dev)
+static void orinoco_set_multicast_list(struct net_device *dev)
{
struct orinoco_private *priv = netdev_priv(dev);
unsigned long flags;
@@ -723,8 +723,7 @@
orinoco_unlock(priv, &flags);
}
-static int
-orinoco_change_mtu(struct net_device *dev, int new_mtu)
+static int orinoco_change_mtu(struct net_device *dev, int new_mtu)
{
struct orinoco_private *priv = netdev_priv(dev);
@@ -744,8 +743,7 @@
/* Tx path */
/********************************************************************/
-static int
-orinoco_xmit(struct sk_buff *skb, struct net_device *dev)
+static int orinoco_xmit(struct sk_buff *skb, struct net_device *dev)
{
struct orinoco_private *priv = netdev_priv(dev);
struct net_device_stats *stats = &priv->stats;
@@ -778,7 +776,6 @@
printk(KERN_ERR "%s: orinoco_xmit() called while hw_unavailable\n",
dev->name);
TRACE_EXIT(dev->name);
-/* BUG(); */
return 1;
}
@@ -846,7 +843,8 @@
}
/* Round up for odd length packets */
- err = hermes_bap_pwrite(hw, USER_BAP, p, ALIGN(data_len, 2), txfid, data_off);
+ err = hermes_bap_pwrite(hw, USER_BAP, p, ALIGN(data_len, 2),
+ txfid, data_off);
if (err) {
printk(KERN_ERR "%s: Error %d writing packet to BAP\n",
dev->name, err);
@@ -857,10 +855,12 @@
/* Finally, we actually initiate the send */
netif_stop_queue(dev);
- err = hermes_docmd_wait(hw, HERMES_CMD_TX | HERMES_CMD_RECL, txfid, NULL);
+ err = hermes_docmd_wait(hw, HERMES_CMD_TX | HERMES_CMD_RECL,
+ txfid, NULL);
if (err) {
netif_start_queue(dev);
- printk(KERN_ERR "%s: Error %d transmitting packet\n", dev->name, err);
+ printk(KERN_ERR "%s: Error %d transmitting packet\n",
+ dev->name, err);
stats->tx_errors++;
goto fail;
}
@@ -885,7 +885,6 @@
static void __orinoco_ev_alloc(struct net_device *dev, hermes_t *hw)
{
struct orinoco_private *priv = netdev_priv(dev);
-
u16 fid = hermes_read_regn(hw, ALLOCFID);
if (fid != priv->txfid) {
@@ -936,8 +935,7 @@
hermes_write_regn(hw, TXCOMPLFID, DUMMY_FID);
}
-static void
-orinoco_tx_timeout(struct net_device *dev)
+static void orinoco_tx_timeout(struct net_device *dev)
{
struct orinoco_private *priv = netdev_priv(dev);
struct net_device_stats *stats = &priv->stats;
@@ -959,8 +957,7 @@
/* Does the frame have a SNAP header indicating it should be
* de-encapsulated to Ethernet-II? */
-static inline int
-is_ethersnap(struct header_struct *hdr)
+static inline int is_ethersnap(struct header_struct *hdr)
{
/* We de-encapsulate all packets which, a) have SNAP headers
* (i.e. SSAP=DSAP=0xaa and CTRL=0x3 in the 802.2 LLC header
@@ -972,7 +969,7 @@
}
static inline void orinoco_spy_gather(struct net_device *dev, u_char *mac,
- int level, int noise)
+ int level, int noise)
{
struct orinoco_private *priv = netdev_priv(dev);
int i;
@@ -988,10 +985,9 @@
}
}
-void
-orinoco_stat_gather(struct net_device *dev,
- struct sk_buff *skb,
- struct hermes_rx_descriptor *desc)
+void orinoco_stat_gather(struct net_device *dev,
+ struct sk_buff *skb,
+ struct hermes_rx_descriptor *desc)
{
struct orinoco_private *priv = netdev_priv(dev);
@@ -1037,7 +1033,7 @@
}
status = le16_to_cpu(desc.status);
-
+
if (status & HERMES_RXSTAT_ERR) {
if (status & HERMES_RXSTAT_UNDECRYPTABLE) {
wstats->discard.code++;
@@ -1100,9 +1096,9 @@
* For some reason, the SNAP frames sent by LinkSys APs
* are not properly recognised by most firmwares.
* So, check ourselves */
- if(((status & HERMES_RXSTAT_MSGTYPE) == HERMES_RXSTAT_1042) ||
- ((status & HERMES_RXSTAT_MSGTYPE) == HERMES_RXSTAT_TUNNEL) ||
- is_ethersnap(&hdr)) {
+ if (((status & HERMES_RXSTAT_MSGTYPE) == HERMES_RXSTAT_1042) ||
+ ((status & HERMES_RXSTAT_MSGTYPE) == HERMES_RXSTAT_TUNNEL) ||
+ is_ethersnap(&hdr)) {
/* These indicate a SNAP within 802.2 LLC within
802.11 frame which we'll need to de-encapsulate to
the original EthernetII frame. */
@@ -1268,7 +1264,7 @@
case HERMES_INQ_LINKSTATUS: {
struct hermes_linkstatus linkstatus;
u16 newstatus;
-
+
if (len != sizeof(linkstatus)) {
printk(KERN_WARNING "%s: Unexpected size for linkstatus frame (%d bytes)\n",
dev->name, len);
@@ -1296,8 +1292,8 @@
}
break;
default:
- printk(KERN_DEBUG "%s: Unknown information frame received (type %04x).\n",
- dev->name, type);
+ printk(KERN_DEBUG "%s: Unknown information frame received "
+ "(type %04x).\n", dev->name, type);
/* We don't actually do anything about it */
break;
}
@@ -1487,7 +1483,8 @@
}
/* Write the index of the key used in transmission */
- err = hermes_write_wordrec(hw, USER_BAP, HERMES_RID_CNFWEPDEFAULTKEYID,
+ err = hermes_write_wordrec(hw, USER_BAP,
+ HERMES_RID_CNFWEPDEFAULTKEYID,
priv->tx_key);
if (err)
return err;
@@ -1507,11 +1504,12 @@
err = hermes_write_wordrec(hw, USER_BAP,
- HERMES_RID_CNFAUTHENTICATION, auth_flag);
+ HERMES_RID_CNFAUTHENTICATION,
+ auth_flag);
if (err)
return err;
}
-
+
/* Master WEP setting : on/off */
err = hermes_write_wordrec(hw, USER_BAP,
HERMES_RID_CNFWEPFLAGS_INTERSIL,
@@ -1543,14 +1541,17 @@
err = hermes_write_ltv(hw, USER_BAP, HERMES_RID_CNFOWNMACADDR,
HERMES_BYTES_TO_RECLEN(ETH_ALEN), dev->dev_addr);
if (err) {
- printk(KERN_ERR "%s: Error %d setting MAC address\n", dev->name, err);
+ printk(KERN_ERR "%s: Error %d setting MAC address\n",
+ dev->name, err);
return err;
}
/* Set up the link mode */
- err = hermes_write_wordrec(hw, USER_BAP, HERMES_RID_CNFPORTTYPE, priv->port_type);
+ err = hermes_write_wordrec(hw, USER_BAP, HERMES_RID_CNFPORTTYPE,
+ priv->port_type);
if (err) {
- printk(KERN_ERR "%s: Error %d setting port type\n", dev->name, err);
+ printk(KERN_ERR "%s: Error %d setting port type\n",
+ dev->name, err);
return err;
}
/* Set the channel/frequency */
@@ -1559,14 +1560,17 @@
if (priv->createibss)
priv->channel = 10;
}
- err = hermes_write_wordrec(hw, USER_BAP, HERMES_RID_CNFOWNCHANNEL, priv->channel);
+ err = hermes_write_wordrec(hw, USER_BAP, HERMES_RID_CNFOWNCHANNEL,
+ priv->channel);
if (err) {
- printk(KERN_ERR "%s: Error %d setting channel\n", dev->name, err);
+ printk(KERN_ERR "%s: Error %d setting channel\n",
+ dev->name, err);
return err;
}
if (priv->has_ibss) {
- err = hermes_write_wordrec(hw, USER_BAP, HERMES_RID_CNFCREATEIBSS,
+ err = hermes_write_wordrec(hw, USER_BAP,
+ HERMES_RID_CNFCREATEIBSS,
priv->createibss);
if (err) {
printk(KERN_ERR "%s: Error %d setting CREATEIBSS\n", dev->name, err);
@@ -1575,8 +1579,8 @@
if ((strlen(priv->desired_essid) == 0) && (priv->createibss)
&& (!priv->has_ibss_any)) {
- printk(KERN_WARNING "%s: This firmware requires an \
-ESSID in IBSS-Ad-Hoc mode.\n", dev->name);
+ printk(KERN_WARNING "%s: This firmware requires an "
+ "ESSID in IBSS-Ad-Hoc mode.\n", dev->name);
/* With wvlan_cs, in this case, we would crash.
* hopefully, this driver will behave better...
* Jean II */
@@ -1591,14 +1595,16 @@
HERMES_BYTES_TO_RECLEN(strlen(priv->desired_essid)+2),
&idbuf);
if (err) {
- printk(KERN_ERR "%s: Error %d setting OWNSSID\n", dev->name, err);
+ printk(KERN_ERR "%s: Error %d setting OWNSSID\n",
+ dev->name, err);
return err;
}
err = hermes_write_ltv(hw, USER_BAP, HERMES_RID_CNFDESIREDSSID,
HERMES_BYTES_TO_RECLEN(strlen(priv->desired_essid)+2),
&idbuf);
if (err) {
- printk(KERN_ERR "%s: Error %d setting DESIREDSSID\n", dev->name, err);
+ printk(KERN_ERR "%s: Error %d setting DESIREDSSID\n",
+ dev->name, err);
return err;
}
@@ -1609,26 +1615,31 @@
HERMES_BYTES_TO_RECLEN(strlen(priv->nick)+2),
&idbuf);
if (err) {
- printk(KERN_ERR "%s: Error %d setting nickname\n", dev->name, err);
+ printk(KERN_ERR "%s: Error %d setting nickname\n",
+ dev->name, err);
return err;
}
/* Set AP density */
if (priv->has_sensitivity) {
- err = hermes_write_wordrec(hw, USER_BAP, HERMES_RID_CNFSYSTEMSCALE,
+ err = hermes_write_wordrec(hw, USER_BAP,
+ HERMES_RID_CNFSYSTEMSCALE,
priv->ap_density);
if (err) {
printk(KERN_WARNING "%s: Error %d setting SYSTEMSCALE. "
- "Disabling sensitivity control\n", dev->name, err);
+ "Disabling sensitivity control\n",
+ dev->name, err);
priv->has_sensitivity = 0;
}
}
/* Set RTS threshold */
- err = hermes_write_wordrec(hw, USER_BAP, HERMES_RID_CNFRTSTHRESHOLD, priv->rts_thresh);
+ err = hermes_write_wordrec(hw, USER_BAP, HERMES_RID_CNFRTSTHRESHOLD,
+ priv->rts_thresh);
if (err) {
- printk(KERN_ERR "%s: Error %d setting RTS threshold\n", dev->name, err);
+ printk(KERN_ERR "%s: Error %d setting RTS threshold\n",
+ dev->name, err);
return err;
}
@@ -1642,20 +1653,23 @@
HERMES_RID_CNFFRAGMENTATIONTHRESHOLD,
priv->frag_thresh);
if (err) {
- printk(KERN_ERR "%s: Error %d setting framentation\n", dev->name, err);
+ printk(KERN_ERR "%s: Error %d setting fragmentation\n",
+ dev->name, err);
return err;
}
/* Set bitrate */
err = __orinoco_hw_set_bitrate(priv);
if (err) {
- printk(KERN_ERR "%s: Error %d setting bitrate\n", dev->name, err);
+ printk(KERN_ERR "%s: Error %d setting bitrate\n",
+ dev->name, err);
return err;
}
/* Set power management */
if (priv->has_pm) {
- err = hermes_write_wordrec(hw, USER_BAP, HERMES_RID_CNFPMENABLED,
+ err = hermes_write_wordrec(hw, USER_BAP,
+ HERMES_RID_CNFPMENABLED,
priv->pm_on);
if (err) {
printk(KERN_ERR "%s: Error %d setting up PM\n",
@@ -1851,7 +1865,7 @@
if (err)
/* When the hardware becomes available again, whatever
* detects that is responsible for re-initializing
- * it. So no need for anything further*/
+ * it. So no need for anything further */
return;
netif_stop_queue(dev);
@@ -1870,8 +1884,8 @@
if (priv->hard_reset)
err = (*priv->hard_reset)(priv);
if (err) {
- printk(KERN_ERR "%s: orinoco_reset: Error %d performing hard reset\n",
- dev->name, err);
+ printk(KERN_ERR "%s: orinoco_reset: Error %d "
+ "performing hard reset\n", dev->name, err);
/* FIXME: shutdown of some sort */
return;
}
@@ -1930,7 +1944,8 @@
/* These are used to detect a runaway interrupt situation */
/* If we get more than MAX_IRQLOOPS_PER_JIFFY iterations in a jiffy,
* we panic and shut down the hardware */
- static int last_irq_jiffy = 0; /* jiffies value the last time we were called */
+ static int last_irq_jiffy = 0; /* jiffies value the last time
+ * we were called */
static int loops_this_jiffy = 0;
unsigned long flags;
@@ -2032,11 +2047,11 @@
dev->name, err);
memset(&sta_id, 0, sizeof(sta_id));
}
+
le16_to_cpus(&sta_id.id);
le16_to_cpus(&sta_id.variant);
le16_to_cpus(&sta_id.major);
le16_to_cpus(&sta_id.minor);
-
printk(KERN_DEBUG "%s: Station identity %04x:%04x:%04x:%04x\n",
dev->name, sta_id.id, sta_id.variant,
sta_id.major, sta_id.minor);
@@ -2149,8 +2164,7 @@
}
}
-static int
-orinoco_init(struct net_device *dev)
+static int orinoco_init(struct net_device *dev)
{
struct orinoco_private *priv = netdev_priv(dev);
hermes_t *hw = &priv->hw;
@@ -2239,7 +2253,8 @@
err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CNFRTSTHRESHOLD,
&priv->rts_thresh);
if (err) {
- printk(KERN_ERR "%s: failed to read RTS threshold!\n", dev->name);
+ printk(KERN_ERR "%s: failed to read RTS threshold!\n",
+ dev->name);
goto out;
}
@@ -2252,7 +2267,8 @@
err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CNFFRAGMENTATIONTHRESHOLD,
&priv->frag_thresh);
if (err) {
- printk(KERN_ERR "%s: failed to read fragmentation settings!\n", dev->name);
+ printk(KERN_ERR "%s: failed to read fragmentation settings!\n",
+ dev->name);
goto out;
}
@@ -2280,7 +2296,8 @@
/* Preamble setup */
if (priv->has_preamble) {
- err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CNFPREAMBLE_SYMBOL,
+ err = hermes_read_wordrec(hw, USER_BAP,
+ HERMES_RID_CNFPREAMBLE_SYMBOL,
&priv->preamble);
if (err)
goto out;
@@ -2329,18 +2346,20 @@
return err;
}
-struct net_device *alloc_orinocodev(int sizeof_card, int (*hard_reset)(struct orinoco_private *))
+struct net_device *alloc_orinocodev(int sizeof_card,
+ int (*hard_reset)(struct orinoco_private *))
{
struct net_device *dev;
struct orinoco_private *priv;
dev = alloc_etherdev(sizeof(struct orinoco_private) + sizeof_card);
- if (!dev)
+ if (! dev)
return NULL;
priv = netdev_priv(dev);
priv->ndev = dev;
if (sizeof_card)
- priv->card = (void *)((unsigned long)netdev_priv(dev) + sizeof(struct orinoco_private));
+ priv->card = (void *)((unsigned long)netdev_priv(dev)
+ + sizeof(struct orinoco_private));
else
priv->card = NULL;
@@ -2700,7 +2719,8 @@
if ((index < 0) || (index >= ORINOCO_MAX_KEYS))
index = priv->tx_key;
-
+
+ /* Adjust key length to a supported value */
if (erq->length > SMALL_KEY_SIZE) {
xlen = LARGE_KEY_SIZE;
} else if (erq->length > 0) {
@@ -2742,14 +2762,14 @@
if (erq->pointer) {
priv->keys[index].len = cpu_to_le16(xlen);
- memset(priv->keys[index].data, 0, sizeof(priv->keys[index].data));
+ memset(priv->keys[index].data, 0,
+ sizeof(priv->keys[index].data));
memcpy(priv->keys[index].data, keybuf, erq->length);
}
priv->tx_key = setindex;
priv->wep_on = enable;
priv->wep_restrict = restricted;
-
out:
orinoco_unlock(priv, &flags);
@@ -2975,7 +2995,8 @@
err = orinoco_lock(priv, &flags);
if (err)
return err;
- err = hermes_read_wordrec(hw, USER_BAP, HERMES_RID_CNFSYSTEMSCALE, &val);
+ err = hermes_read_wordrec(hw, USER_BAP,
+ HERMES_RID_CNFSYSTEMSCALE, &val);
orinoco_unlock(priv, &flags);
if (err)
@@ -3461,7 +3482,6 @@
*val = priv->prefer_port3;
orinoco_unlock(priv, &flags);
-
return 0;
}
Index: working-2.6/drivers/net/wireless/orinoco_pci.c
===================================================================
--- working-2.6.orig/drivers/net/wireless/orinoco_pci.c 2004-07-28 14:57:52.312664192 +1000
+++ working-2.6/drivers/net/wireless/orinoco_pci.c 2004-07-28 14:57:53.048552320 +1000
@@ -206,18 +206,17 @@
if (! pci_iorange)
goto fail;
- /* Usual setup of structures */
+ /* Allocate network device */
dev = alloc_orinocodev(0, NULL);
if (! dev) {
err = -ENOMEM;
goto fail;
}
- priv = netdev_priv(dev);
+ priv = netdev_priv(dev);
dev->base_addr = (unsigned long) pci_ioaddr;
dev->mem_start = pci_iorange;
dev->mem_end = pci_iorange + pci_iolen - 1;
-
SET_MODULE_OWNER(dev);
SET_NETDEV_DEV(dev, &pdev->dev);
@@ -238,6 +237,7 @@
goto fail;
}
dev->irq = pdev->irq;
+
/* Perform a COR reset to start the card */
if(orinoco_pci_cor_reset(priv) != 0) {
printk(KERN_ERR "%s: Failed to start the card\n", dev->name);
@@ -255,7 +255,8 @@
goto fail;
}
- return 0; /* succeeded */
+ return 0;
+
fail:
if (dev) {
if (dev->irq)
@@ -279,7 +280,7 @@
unregister_netdev(dev);
- if (dev->irq)
+ if (dev->irq)
free_irq(dev->irq, dev);
if (priv->hw.iobase)
@@ -357,7 +358,9 @@
}
static struct pci_device_id orinoco_pci_pci_id_table[] = {
+ /* Intersil Prism 3 */
{0x1260, 0x3872, PCI_ANY_ID, PCI_ANY_ID,},
+ /* Intersil Prism 2.5 */
{0x1260, 0x3873, PCI_ANY_ID, PCI_ANY_ID,},
{0,},
};
Index: working-2.6/drivers/net/wireless/orinoco.h
===================================================================
--- working-2.6.orig/drivers/net/wireless/orinoco.h 2004-07-28 14:56:33.743608504 +1000
+++ working-2.6/drivers/net/wireless/orinoco.h 2004-07-28 14:57:53.049552168 +1000
@@ -12,6 +12,7 @@
#include <linux/netdevice.h>
#include <linux/wireless.h>
#include <linux/version.h>
+
#include "hermes.h"
/* To enable debug messages */
@@ -50,7 +51,6 @@
hermes_t hw;
u16 txfid;
-
/* Capabilities of the hardware/firmware */
int firmware_type;
#define FIRMWARE_TYPE_AGERE 1
@@ -100,6 +100,10 @@
#define TRACE_ENTER(devname) DEBUG(2, "%s: -> %s()\n", devname, __FUNCTION__);
#define TRACE_EXIT(devname) DEBUG(2, "%s: <- %s()\n", devname, __FUNCTION__);
+/********************************************************************/
+/* Exported prototypes */
+/********************************************************************/
+
extern struct net_device *alloc_orinocodev(int sizeof_card,
int (*hard_reset)(struct orinoco_private *));
extern int __orinoco_up(struct net_device *dev);
Index: working-2.6/drivers/net/wireless/orinoco_tmd.c
===================================================================
--- working-2.6.orig/drivers/net/wireless/orinoco_tmd.c 2004-07-28 14:57:52.314663888 +1000
+++ working-2.6/drivers/net/wireless/orinoco_tmd.c 2004-07-28 14:57:53.051551864 +1000
@@ -78,8 +78,7 @@
static char dev_info[] = "orinoco_tmd";
-#define COR_VALUE (COR_LEVEL_REQ | COR_FUNC_ENA | COR_FUNC_ENA) /* Enable PC card with level triggered irqs and irq requests */
-
+#define COR_VALUE (COR_LEVEL_REQ | COR_FUNC_ENA | COR_FUNC_ENA) /* Enable PC card with interrupt in level trigger */
static int orinoco_tmd_init_one(struct pci_dev *pdev,
const struct pci_device_id *ent)
@@ -115,6 +114,7 @@
goto fail;
}
+ /* Allocate network device */
dev = alloc_orinocodev(0, NULL);
if (! dev) {
err = -ENOMEM;
@@ -126,16 +126,16 @@
SET_MODULE_OWNER(dev);
SET_NETDEV_DEV(dev, &pdev->dev);
- printk(KERN_DEBUG
- "Detected Orinoco/Prism2 TMD device at %s irq:%d, io addr:0x%lx\n",
- pci_name(pdev), pdev->irq, pccard_ioaddr);
+ printk(KERN_DEBUG "Detected Orinoco/Prism2 TMD device "
+ "at %s irq:%d, io addr:0x%lx\n", pci_name(pdev), pdev->irq,
+ pccard_ioaddr);
hermes_struct_init(&(priv->hw), dev->base_addr,
HERMES_IO, HERMES_16BIT_REGSPACING);
pci_set_drvdata(pdev, dev);
- err = request_irq(pdev->irq, orinoco_interrupt, SA_SHIRQ, dev->name,
- dev);
+ err = request_irq(pdev->irq, orinoco_interrupt, SA_SHIRQ,
+ dev->name, dev);
if (err) {
printk(KERN_ERR "orinoco_tmd: Error allocating IRQ %d.\n",
pdev->irq);
@@ -148,9 +148,9 @@
if (err)
goto fail;
- return 0; /* succeeded */
+ return 0;
- fail:
+ fail:
printk(KERN_DEBUG "orinoco_tmd: init_one(), FAIL!\n");
if (dev) {
Index: working-2.6/drivers/net/wireless/orinoco_plx.c
===================================================================
--- working-2.6.orig/drivers/net/wireless/orinoco_plx.c 2004-07-28 14:57:52.313664040 +1000
+++ working-2.6/drivers/net/wireless/orinoco_plx.c 2004-07-28 14:57:53.054551408 +1000
@@ -1,7 +1,7 @@
/* orinoco_plx.c 0.13e
*
* Driver for Prism II devices which would usually be driven by orinoco_cs,
- * but are connected to the PCI bus by a PLX9052.
+ * but are connected to the PCI bus by a PLX9052.
*
* Copyright (C) 2001 Daniel Barlow <dan AT telent.net>
*
@@ -33,77 +33,80 @@
* drop me mail with the id and "it works"/"it doesn't work".
*
* Note: if everything gets detected fine but it doesn't actually send
- * or receive packets, your first port of call should probably be to
+ * or receive packets, your first port of call should probably be to
* try newer firmware in the card. Especially if you're doing Ad-Hoc
- * modes
+ * modes.
*
* The actual driving is done by orinoco.c, this is just resource
* allocation stuff. The explanation below is courtesy of Ryan Niemi
* on the linux-wlan-ng list at
* http://archives.neohapsis.com/archives/dev/linux-wlan/2001-q1/0026.html
-
-The PLX9052-based cards (WL11000 and several others) are a different
-beast than the usual PCMCIA-based PRISM2 configuration expected by
-wlan-ng. Here's the general details on how the WL11000 PCI adapter
-works:
-
- - Two PCI I/O address spaces, one 0x80 long which contains the PLX9052
- registers, and one that's 0x40 long mapped to the PCMCIA slot I/O
- address space.
-
- - One PCI memory address space, mapped to the PCMCIA memory space
- (containing the CIS).
-
-After identifying the I/O and memory space, you can read through the
-memory space to confirm the CIS's device ID or manufacturer ID to make
-sure it's the expected card. Keep in mind that the PCMCIA spec specifies
-the CIS as the lower 8 bits of each word read from the CIS, so to read the
-bytes of the CIS, read every other byte (0,2,4,...). Passing that test,
-you need to enable the I/O address space on the PCMCIA card via the PCMCIA
-COR register. This is the first byte following the CIS. In my case
-(which may not have any relation to what's on the PRISM2 cards), COR was
-at offset 0x800 within the PCI memory space. Write 0x41 to the COR
-register to enable I/O mode and to select level triggered interrupts. To
-confirm you actually succeeded, read the COR register back and make sure
-it actually got set to 0x41, incase you have an unexpected card inserted.
-
-Following that, you can treat the second PCI I/O address space (the one
-that's not 0x80 in length) as the PCMCIA I/O space.
-
-Note that in the Eumitcom's source for their drivers, they register the
-interrupt as edge triggered when registering it with the Windows kernel. I
-don't recall how to register edge triggered on Linux (if it can be done at
-all). But in some experimentation, I don't see much operational
-difference between using either interrupt mode. Don't mess with the
-interrupt mode in the COR register though, as the PLX9052 wants level
-triggers with the way the serial EEPROM configures it on the WL11000.
-
-There's some other little quirks related to timing that I bumped into, but
-I don't recall right now. Also, there's two variants of the WL11000 I've
-seen, revision A1 and T2. These seem to differ slightly in the timings
-configured in the wait-state generator in the PLX9052. There have also
-been some comments from Eumitcom that cards shouldn't be hot swapped,
-apparently due to risk of cooking the PLX9052. I'm unsure why they
-believe this, as I can't see anything in the design that would really
-cause a problem, except for crashing drivers not written to expect it. And
-having developed drivers for the WL11000, I'd say it's quite tricky to
-write code that will successfully deal with a hot unplug. Very odd things
-happen on the I/O side of things. But anyway, be warned. Despite that,
-I've hot-swapped a number of times during debugging and driver development
-for various reasons (stuck WAIT# line after the radio card's firmware
-locks up).
-
-Hope this is enough info for someone to add PLX9052 support to the wlan-ng
-card. In the case of the WL11000, the PCI ID's are 0x1639/0x0200, with
-matching subsystem ID's. Other PLX9052-based manufacturers other than
-Eumitcom (or on cards other than the WL11000) may have different PCI ID's.
-
-If anyone needs any more specific info, let me know. I haven't had time
-to implement support myself yet, and with the way things are going, might
-not have time for a while..
-
----end of mail---
-*/
+ *
+ * The PLX9052-based cards (WL11000 and several others) are a
+ * different beast than the usual PCMCIA-based PRISM2 configuration
+ * expected by wlan-ng. Here's the general details on how the WL11000
+ * PCI adapter works:
+ *
+ * - Two PCI I/O address spaces, one 0x80 long which contains the
+ * PLX9052 registers, and one that's 0x40 long mapped to the PCMCIA
+ * slot I/O address space.
+ *
+ * - One PCI memory address space, mapped to the PCMCIA memory space
+ * (containing the CIS).
+ *
+ * After identifying the I/O and memory space, you can read through
+ * the memory space to confirm the CIS's device ID or manufacturer ID
+ * to make sure it's the expected card. qKeep in mind that the PCMCIA
+ * spec specifies the CIS as the lower 8 bits of each word read from
+ * the CIS, so to read the bytes of the CIS, read every other byte
+ * (0,2,4,...). Passing that test, you need to enable the I/O address
+ * space on the PCMCIA card via the PCMCIA COR register. This is the
+ * first byte following the CIS. In my case (which may not have any
+ * relation to what's on the PRISM2 cards), COR was at offset 0x800
+ * within the PCI memory space. Write 0x41 to the COR register to
+ * enable I/O mode and to select level triggered interrupts. To
+ * confirm you actually succeeded, read the COR register back and make
+ * sure it actually got set to 0x41, incase you have an unexpected
+ * card inserted.
+ *
+ * Following that, you can treat the second PCI I/O address space (the
+ * one that's not 0x80 in length) as the PCMCIA I/O space.
+ *
+ * Note that in the Eumitcom's source for their drivers, they register
+ * the interrupt as edge triggered when registering it with the
+ * Windows kernel. I don't recall how to register edge triggered on
+ * Linux (if it can be done at all). But in some experimentation, I
+ * don't see much operational difference between using either
+ * interrupt mode. Don't mess with the interrupt mode in the COR
+ * register though, as the PLX9052 wants level triggers with the way
+ * the serial EEPROM configures it on the WL11000.
+ *
+ * There's some other little quirks related to timing that I bumped
+ * into, but I don't recall right now. Also, there's two variants of
+ * the WL11000 I've seen, revision A1 and T2. These seem to differ
+ * slightly in the timings configured in the wait-state generator in
+ * the PLX9052. There have also been some comments from Eumitcom that
+ * cards shouldn't be hot swapped, apparently due to risk of cooking
+ * the PLX9052. I'm unsure why they believe this, as I can't see
+ * anything in the design that would really cause a problem, except
+ * for crashing drivers not written to expect it. And having developed
+ * drivers for the WL11000, I'd say it's quite tricky to write code
+ * that will successfully deal with a hot unplug. Very odd things
+ * happen on the I/O side of things. But anyway, be warned. Despite
+ * that, I've hot-swapped a number of times during debugging and
+ * driver development for various reasons (stuck WAIT# line after the
+ * radio card's firmware locks up).
+ *
+ * Hope this is enough info for someone to add PLX9052 support to the
+ * wlan-ng card. In the case of the WL11000, the PCI ID's are
+ * 0x1639/0x0200, with matching subsystem ID's. Other PLX9052-based
+ * manufacturers other than Eumitcom (or on cards other than the
+ * WL11000) may have different PCI ID's.
+ *
+ * If anyone needs any more specific info, let me know. I haven't had
+ * time to implement support myself yet, and with the way things are
+ * going, might not have time for a while..
+ */
#include <linux/config.h>
@@ -134,11 +137,11 @@
static char dev_info[] = "orinoco_plx";
-#define COR_OFFSET (0x3e0 / 2) /* COR attribute offset of Prism2 PC card */
-#define COR_VALUE (COR_LEVEL_REQ | COR_FUNC_ENA) /* Enable PC card with interrupt in level trigger */
+#define COR_OFFSET (0x3e0/2) /* COR attribute offset of Prism2 PC card */
+#define COR_VALUE (COR_LEVEL_REQ | COR_FUNC_ENA) /* Enable PC card with interrupt in level trigger */
-#define PLX_INTCSR 0x4c /* Interrupt Control and Status Register */
-#define PLX_INTCSR_INTEN (1<<6) /* Interrupt Enable bit */
+#define PLX_INTCSR 0x4c /* Interrupt Control & Status Register */
+#define PLX_INTCSR_INTEN (1<<6) /* Interrupt Enable bit */
static const u16 cis_magic[] = {
0x0001, 0x0003, 0x0000, 0x0000, 0x00ff, 0x0017, 0x0004, 0x0067
@@ -223,6 +226,7 @@
goto fail;
}
+ /* Allocate network device */
dev = alloc_orinocodev(0, NULL);
if (! dev) {
err = -ENOMEM;
@@ -234,15 +238,16 @@
SET_MODULE_OWNER(dev);
SET_NETDEV_DEV(dev, &pdev->dev);
- printk(KERN_DEBUG
- "Detected Orinoco/Prism2 PLX device at %s irq:%d, io addr:0x%lx\n",
- pci_name(pdev), pdev->irq, pccard_ioaddr);
+ printk(KERN_DEBUG "Detected Orinoco/Prism2 PLX device "
+ "at %s irq:%d, io addr:0x%lx\n", pci_name(pdev), pdev->irq,
+ pccard_ioaddr);
- hermes_struct_init(&(priv->hw), dev->base_addr,
- HERMES_IO, HERMES_16BIT_REGSPACING);
+ hermes_struct_init(&(priv->hw), dev->base_addr, HERMES_IO,
+ HERMES_16BIT_REGSPACING);
pci_set_drvdata(pdev, dev);
- err = request_irq(pdev->irq, orinoco_interrupt, SA_SHIRQ, dev->name, dev);
+ err = request_irq(pdev->irq, orinoco_interrupt, SA_SHIRQ,
+ dev->name, dev);
if (err) {
printk(KERN_ERR "orinoco_plx: Error allocating IRQ %d.\n", pdev->irq);
err = -EBUSY;
@@ -254,9 +259,9 @@
if (err)
goto fail;
- return 0; /* succeeded */
+ return 0;
- fail:
+ fail:
printk(KERN_DEBUG "orinoco_plx: init_one(), FAIL!\n");
if (dev) {
@@ -305,7 +310,7 @@
{0x15e8, 0x0130, PCI_ANY_ID, PCI_ANY_ID,}, /* Correga - does this work? */
{0x1638, 0x1100, PCI_ANY_ID, PCI_ANY_ID,}, /* SMC EZConnect SMC2602W,
Eumitcom PCI WL11000,
- Addtron AWA-100*/
+ Addtron AWA-100 */
{0x16ab, 0x1100, PCI_ANY_ID, PCI_ANY_ID,}, /* Global Sun Tech GL24110P */
{0x16ab, 0x1101, PCI_ANY_ID, PCI_ANY_ID,}, /* Reported working, but unknown */
{0x16ab, 0x1102, PCI_ANY_ID, PCI_ANY_ID,}, /* Linksys WDT11 */
Index: working-2.6/drivers/net/wireless/hermes.c
===================================================================
--- working-2.6.orig/drivers/net/wireless/hermes.c 2004-07-28 14:56:32.927732536 +1000
+++ working-2.6/drivers/net/wireless/hermes.c 2004-07-28 14:57:53.055551256 +1000
@@ -390,7 +390,6 @@
return -EIO;
}
-
return 0;
}
Index: working-2.6/drivers/net/wireless/orinoco_cs.c
===================================================================
--- working-2.6.orig/drivers/net/wireless/orinoco_cs.c 2004-07-28 14:57:49.305121408 +1000
+++ working-2.6/drivers/net/wireless/orinoco_cs.c 2004-07-28 14:57:53.058550800 +1000
@@ -219,8 +219,7 @@
* are freed. Otherwise, the structures will be freed when the device
* is released.
*/
-static void
-orinoco_cs_detach(dev_link_t * link)
+static void orinoco_cs_detach(dev_link_t *link)
{
dev_link_t **linkp;
struct net_device *dev = link->priv;
@@ -258,8 +257,9 @@
* device available to the system.
*/
-#define CS_CHECK(fn, ret) \
-do { last_fn = (fn); if ((last_ret = (ret)) != 0) goto cs_failed; } while (0)
+#define CS_CHECK(fn, ret) do { \
+ last_fn = (fn); if ((last_ret = (ret)) != 0) goto cs_failed; \
+ } while (0)
static void
orinoco_cs_config(dev_link_t *link)
@@ -297,7 +297,8 @@
link->state |= DEV_CONFIG;
/* Look up the current Vcc */
- CS_CHECK(GetConfigurationInfo, pcmcia_get_configuration_info(handle, &conf));
+ CS_CHECK(GetConfigurationInfo,
+ pcmcia_get_configuration_info(handle, &conf));
link->conf.Vcc = conf.Vcc;
/*
@@ -401,8 +402,9 @@
pcmcia_release_io(link->handle, &link->io);
last_ret = pcmcia_get_next_tuple(handle, &tuple);
if (last_ret == CS_NO_MORE_ITEMS) {
- printk(KERN_ERR "GetNextTuple(). No matching CIS configuration, "
- "maybe you need the ignore_cis_vcc=1 parameter.\n");
+ printk(KERN_ERR "GetNextTuple(). No matching "
+ "CIS configuration, maybe you need the "
+ "ignore_cis_vcc=1 parameter.\n");
goto cs_failed;
}
}
@@ -440,7 +442,8 @@
* the I/O windows and the interrupt mapping, and putting the
* card and host interface into "Memory and IO" mode.
*/
- CS_CHECK(RequestConfiguration, pcmcia_request_configuration(link->handle, &link->conf));
+ CS_CHECK(RequestConfiguration,
+ pcmcia_request_configuration(link->handle, &link->conf));
/* Ok, we have the configuration, prepare to register the netdev */
dev->base_addr = link->io.BasePort1;
@@ -659,4 +662,3 @@
module_init(init_orinoco_cs);
module_exit(exit_orinoco_cs);
-
Index: working-2.6/drivers/net/wireless/hermes_rid.h
===================================================================
--- working-2.6.orig/drivers/net/wireless/hermes_rid.h 2004-07-28 14:56:33.745608200 +1000
+++ working-2.6/drivers/net/wireless/hermes_rid.h 2004-07-28 14:57:53.060550496 +1000
@@ -4,21 +4,21 @@
/*
* Configuration RIDs
*/
-#define HERMES_RID_CNFPORTTYPE 0xFC00 /* used */
-#define HERMES_RID_CNFOWNMACADDR 0xFC01 /* used */
-#define HERMES_RID_CNFDESIREDSSID 0xFC02 /* used */
-#define HERMES_RID_CNFOWNCHANNEL 0xFC03 /* used */
-#define HERMES_RID_CNFOWNSSID 0xFC04 /* used */
+#define HERMES_RID_CNFPORTTYPE 0xFC00
+#define HERMES_RID_CNFOWNMACADDR 0xFC01
+#define HERMES_RID_CNFDESIREDSSID 0xFC02
+#define HERMES_RID_CNFOWNCHANNEL 0xFC03
+#define HERMES_RID_CNFOWNSSID 0xFC04
#define HERMES_RID_CNFOWNATIMWINDOW 0xFC05
-#define HERMES_RID_CNFSYSTEMSCALE 0xFC06 /* used */
+#define HERMES_RID_CNFSYSTEMSCALE 0xFC06
#define HERMES_RID_CNFMAXDATALEN 0xFC07
#define HERMES_RID_CNFWDSADDRESS 0xFC08
-#define HERMES_RID_CNFPMENABLED 0xFC09 /* used */
+#define HERMES_RID_CNFPMENABLED 0xFC09
#define HERMES_RID_CNFPMEPS 0xFC0A
-#define HERMES_RID_CNFMULTICASTRECEIVE 0xFC0B /* used */
-#define HERMES_RID_CNFMAXSLEEPDURATION 0xFC0C /* used */
-#define HERMES_RID_CNFPMHOLDOVERDURATION 0xFC0D /* used */
-#define HERMES_RID_CNFOWNNAME 0xFC0E /* used */
+#define HERMES_RID_CNFMULTICASTRECEIVE 0xFC0B
+#define HERMES_RID_CNFMAXSLEEPDURATION 0xFC0C
+#define HERMES_RID_CNFPMHOLDOVERDURATION 0xFC0D
+#define HERMES_RID_CNFOWNNAME 0xFC0E
#define HERMES_RID_CNFOWNDTIMPERIOD 0xFC10
#define HERMES_RID_CNFWDSADDRESS1 0xFC11
#define HERMES_RID_CNFWDSADDRESS2 0xFC12
@@ -27,17 +27,17 @@
#define HERMES_RID_CNFWDSADDRESS5 0xFC15
#define HERMES_RID_CNFWDSADDRESS6 0xFC16
#define HERMES_RID_CNFMULTICASTPMBUFFERING 0xFC17
-#define HERMES_RID_CNFWEPENABLED_AGERE 0xFC20 /* used */
+#define HERMES_RID_CNFWEPENABLED_AGERE 0xFC20
#define HERMES_RID_CNFMANDATORYBSSID_SYMBOL 0xFC21
-#define HERMES_RID_CNFWEPDEFAULTKEYID 0xFC23 /* used */
-#define HERMES_RID_CNFDEFAULTKEY0 0xFC24 /* used */
-#define HERMES_RID_CNFDEFAULTKEY1 0xFC25 /* used */
-#define HERMES_RID_CNFMWOROBUST_AGERE 0xFC25 /* used */
-#define HERMES_RID_CNFDEFAULTKEY2 0xFC26 /* used */
-#define HERMES_RID_CNFDEFAULTKEY3 0xFC27 /* used */
-#define HERMES_RID_CNFWEPFLAGS_INTERSIL 0xFC28 /* used */
+#define HERMES_RID_CNFWEPDEFAULTKEYID 0xFC23
+#define HERMES_RID_CNFDEFAULTKEY0 0xFC24
+#define HERMES_RID_CNFDEFAULTKEY1 0xFC25
+#define HERMES_RID_CNFMWOROBUST_AGERE 0xFC25
+#define HERMES_RID_CNFDEFAULTKEY2 0xFC26
+#define HERMES_RID_CNFDEFAULTKEY3 0xFC27
+#define HERMES_RID_CNFWEPFLAGS_INTERSIL 0xFC28
#define HERMES_RID_CNFWEPKEYMAPPINGTABLE 0xFC29
-#define HERMES_RID_CNFAUTHENTICATION 0xFC2A /* used */
+#define HERMES_RID_CNFAUTHENTICATION 0xFC2A
#define HERMES_RID_CNFMAXASSOCSTA 0xFC2B
#define HERMES_RID_CNFKEYLENGTH_SYMBOL 0xFC2B
#define HERMES_RID_CNFTXCONTROL 0xFC2C
@@ -53,14 +53,14 @@
#define HERMES_RID_CNFTIMCTRL 0xFC40
#define HERMES_RID_CNFTHIRTY2TALLY 0xFC42
#define HERMES_RID_CNFENHSECURITY 0xFC43
-#define HERMES_RID_CNFGROUPADDRESSES 0xFC80 /* used */
-#define HERMES_RID_CNFCREATEIBSS 0xFC81 /* used */
-#define HERMES_RID_CNFFRAGMENTATIONTHRESHOLD 0xFC82 /* used */
-#define HERMES_RID_CNFRTSTHRESHOLD 0xFC83 /* used */
-#define HERMES_RID_CNFTXRATECONTROL 0xFC84 /* used */
-#define HERMES_RID_CNFPROMISCUOUSMODE 0xFC85 /* used */
+#define HERMES_RID_CNFGROUPADDRESSES 0xFC80
+#define HERMES_RID_CNFCREATEIBSS 0xFC81
+#define HERMES_RID_CNFFRAGMENTATIONTHRESHOLD 0xFC82
+#define HERMES_RID_CNFRTSTHRESHOLD 0xFC83
+#define HERMES_RID_CNFTXRATECONTROL 0xFC84
+#define HERMES_RID_CNFPROMISCUOUSMODE 0xFC85
#define HERMES_RID_CNFBASICRATES_SYMBOL 0xFC8A
-#define HERMES_RID_CNFPREAMBLE_SYMBOL 0xFC8C /* used */
+#define HERMES_RID_CNFPREAMBLE_SYMBOL 0xFC8C
#define HERMES_RID_CNFFRAGMENTATIONTHRESHOLD0 0xFC90
#define HERMES_RID_CNFFRAGMENTATIONTHRESHOLD1 0xFC91
#define HERMES_RID_CNFFRAGMENTATIONTHRESHOLD2 0xFC92
@@ -76,13 +76,13 @@
#define HERMES_RID_CNFRTSTHRESHOLD5 0xFC9C
#define HERMES_RID_CNFRTSTHRESHOLD6 0xFC9D
#define HERMES_RID_CNFSHORTPREAMBLE 0xFCB0
-#define HERMES_RID_CNFWEPKEYS_AGERE 0xFCB0 /* used */
+#define HERMES_RID_CNFWEPKEYS_AGERE 0xFCB0
#define HERMES_RID_CNFEXCLUDELONGPREAMBLE 0xFCB1
-#define HERMES_RID_CNFTXKEY_AGERE 0xFCB1 /* used */
+#define HERMES_RID_CNFTXKEY_AGERE 0xFCB1
#define HERMES_RID_CNFAUTHENTICATIONRSPTO 0xFCB2
#define HERMES_RID_CNFBASICRATES 0xFCB3
#define HERMES_RID_CNFSUPPORTEDRATES 0xFCB4
-#define HERMES_RID_CNFTICKTIME 0xFCE0 /* used */
+#define HERMES_RID_CNFTICKTIME 0xFCE0
#define HERMES_RID_CNFSCANREQUEST 0xFCE1
#define HERMES_RID_CNFJOINREQUEST 0xFCE2
#define HERMES_RID_CNFAUTHENTICATESTATION 0xFCE3
@@ -100,26 +100,26 @@
#define HERMES_RID_NICID 0xFD0B
#define HERMES_RID_MFISUPRANGE 0xFD0C
#define HERMES_RID_CFISUPRANGE 0xFD0D
-#define HERMES_RID_CHANNELLIST 0xFD10 /* used */
+#define HERMES_RID_CHANNELLIST 0xFD10
#define HERMES_RID_REGULATORYDOMAINS 0xFD11
#define HERMES_RID_TEMPTYPE 0xFD12
#define HERMES_RID_CIS 0xFD13
-#define HERMES_RID_STAID 0xFD20 /* used */
+#define HERMES_RID_STAID 0xFD20
#define HERMES_RID_STASUPRANGE 0xFD21
#define HERMES_RID_MFIACTRANGES 0xFD22
#define HERMES_RID_CFIACTRANGES2 0xFD23
-#define HERMES_RID_SECONDARYVERSION_SYMBOL 0xFD24 /* used */
+#define HERMES_RID_SECONDARYVERSION_SYMBOL 0xFD24
#define HERMES_RID_PORTSTATUS 0xFD40
-#define HERMES_RID_CURRENTSSID 0xFD41 /* used */
-#define HERMES_RID_CURRENTBSSID 0xFD42 /* used */
-#define HERMES_RID_COMMSQUALITY 0xFD43 /* used */
-#define HERMES_RID_CURRENTTXRATE 0xFD44 /* used */
+#define HERMES_RID_CURRENTSSID 0xFD41
+#define HERMES_RID_CURRENTBSSID 0xFD42
+#define HERMES_RID_COMMSQUALITY 0xFD43
+#define HERMES_RID_CURRENTTXRATE 0xFD44
#define HERMES_RID_CURRENTBEACONINTERVAL 0xFD45
#define HERMES_RID_CURRENTSCALETHRESHOLDS 0xFD46
#define HERMES_RID_PROTOCOLRSPTIME 0xFD47
-#define HERMES_RID_SHORTRETRYLIMIT 0xFD48 /* used */
-#define HERMES_RID_LONGRETRYLIMIT 0xFD49 /* used */
-#define HERMES_RID_MAXTRANSMITLIFETIME 0xFD4A /* used */
+#define HERMES_RID_SHORTRETRYLIMIT 0xFD48
+#define HERMES_RID_LONGRETRYLIMIT 0xFD49
+#define HERMES_RID_MAXTRANSMITLIFETIME 0xFD4A
#define HERMES_RID_MAXRECEIVELIFETIME 0xFD4B
#define HERMES_RID_CFPOLLABLE 0xFD4C
#define HERMES_RID_AUTHENTICATIONALGORITHMS 0xFD4D
@@ -133,10 +133,10 @@
#define HERMES_RID_OWNMACADDR 0xFD86
#define HERMES_RID_SCANRESULTSTABLE 0xFD88
#define HERMES_RID_PHYTYPE 0xFDC0
-#define HERMES_RID_CURRENTCHANNEL 0xFDC1 /* used */
+#define HERMES_RID_CURRENTCHANNEL 0xFDC1
#define HERMES_RID_CURRENTPOWERSTATE 0xFDC2
#define HERMES_RID_CCAMODE 0xFDC3
-#define HERMES_RID_SUPPORTEDDATARATES 0xFDC6 /* used */
+#define HERMES_RID_SUPPORTEDDATARATES 0xFDC6
#define HERMES_RID_BUILDSEQ 0xFFFE
#define HERMES_RID_FWID 0xFFFF
Index: working-2.6/drivers/net/wireless/hermes.h
===================================================================
--- working-2.6.orig/drivers/net/wireless/hermes.h 2004-07-28 14:56:48.180413776 +1000
+++ working-2.6/drivers/net/wireless/hermes.h 2004-07-28 14:58:27.164365928 +1000
@@ -124,22 +124,22 @@
/*
* Command codes
*/
-/*--- Controller Commands --------------------------*/
+/*--- Controller Commands ----------------------------*/
#define HERMES_CMD_INIT (0x0000)
#define HERMES_CMD_ENABLE (0x0001)
#define HERMES_CMD_DISABLE (0x0002)
#define HERMES_CMD_DIAG (0x0003)
-/*--- Buffer Mgmt Commands --------------------------*/
+/*--- Buffer Mgmt Commands ---------------------------*/
#define HERMES_CMD_ALLOC (0x000A)
#define HERMES_CMD_TX (0x000B)
#define HERMES_CMD_CLRPRST (0x0012)
-/*--- Regulate Commands --------------------------*/
+/*--- Regulate Commands ------------------------------*/
#define HERMES_CMD_NOTIFY (0x0010)
#define HERMES_CMD_INQUIRE (0x0011)
-/*--- Configure Commands --------------------------*/
+/*--- Configure Commands -----------------------------*/
#define HERMES_CMD_ACCESS (0x0021)
#define HERMES_CMD_DOWNLD (0x0022)
@@ -312,9 +312,11 @@
#define hermes_write_regn(hw, name, val) hermes_write_reg((hw), HERMES_##name, (val))
/* Function prototypes */
-void hermes_struct_init(hermes_t *hw, ulong address, int io_space, int reg_spacing);
+void hermes_struct_init(hermes_t *hw, ulong address, int io_space,
+ int reg_spacing);
int hermes_init(hermes_t *hw);
-int hermes_docmd_wait(hermes_t *hw, u16 cmd, u16 parm0, hermes_response_t *resp);
+int hermes_docmd_wait(hermes_t *hw, u16 cmd, u16 parm0,
+ hermes_response_t *resp);
int hermes_allocate(hermes_t *hw, u16 size, u16 *fid);
int hermes_bap_pread(hermes_t *hw, int bap, void *buf, unsigned len,
Index: working-2.6/drivers/net/wireless/ieee802_11.h
===================================================================
--- working-2.6.orig/drivers/net/wireless/ieee802_11.h 2004-05-20 12:58:17.000000000 +1000
+++ working-2.6/drivers/net/wireless/ieee802_11.h 2004-07-28 14:57:53.063550040 +1000
@@ -76,4 +76,3 @@
#define IEEE802_11_SCTL_SEQ 0xFFF0
#endif /* _IEEE802_11_H */
-
--
David Gibson | For every complex problem there is a
david AT gibson.dropbear.id.au | solution which is simple, neat and
| wrong.
http://www.ozlabs.org/people/dgibson
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/