Re: Ho ho ho - Linux v2.6.10 (module strangeness)
From: Chris Rankin
Date: Sun Dec 26 2004 - 06:51:03 EST
I'm also seeing "unresolved symbols" messages (with
ohci1394), but the modules are present and do load.
The eth1394 module was also managing to grab "eth0"
from e1000, despite this line in my modprobe.conf
file:
install eth1394 { /sbin/modprobe e1000; /sbin/modprobe
--ignore-install eth1394; }
I had to blacklist the eth1394 module so that the
hot-plugging would ignore it.
"pci=routeirq" was used because my radeon DRM module
wouldn't behave without it.
And the ttyS0 and ttyS1 ports are being reported twice
by the serial code. Very strange.
Cheers,
Chris
----------------------------------------------------
Linux version 2.6.10 (chris@xxxxxxxxxxxxxxxxxx) (gcc
version 3.4.3) #1 SMP Sun Dec 26 00:02:33 GMT 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000
(usable)
BIOS-e820: 00000000000f0000 - 0000000000100000
(reserved)
BIOS-e820: 0000000000100000 - 000000003ff75000
(usable)
BIOS-e820: 000000003ff75000 - 000000003ff77000 (ACPI
NVS)
BIOS-e820: 000000003ff77000 - 000000003ff98000 (ACPI
data)
BIOS-e820: 000000003ff98000 - 0000000040000000
(reserved)
BIOS-e820: 00000000fec00000 - 00000000fec90000
(reserved)
BIOS-e820: 00000000fee00000 - 00000000fee10000
(reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000
(reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000fe710
On node 0 totalpages: 262005
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 225280 pages, LIFO batch:16
HighMem zone: 32629 pages, LIFO batch:7
DMI 2.3 present.
ACPI: RSDP (v000 DELL
) @ 0x000febc0
ACPI: RSDT (v001 DELL WS 650 0x00000008 ASL
0x00000061) @ 0x000fd4d4
ACPI: FADT (v001 DELL WS 650 0x00000008 ASL
0x00000061) @ 0x000fd50c
ACPI: SSDT (v001 DELL st_ex 0x00001000 MSFT
0x0100000d) @ 0xffff373d
ACPI: MADT (v001 DELL WS 650 0x00000008 ASL
0x00000061) @ 0x000fd580
ACPI: BOOT (v001 DELL WS 650 0x00000008 ASL
0x00000061) @ 0x000fd604
ACPI: ASF! (v016 DELL WS 650 0x00000008 ASL
0x00000061) @ 0x000fd62c
ACPI: DSDT (v001 DELL dt_ex 0x00001000 MSFT
0x0100000d) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x06] enabled)
Processor #6 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled)
Processor #1 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x07] enabled)
Processor #7 15:2 APIC version 20
ACPI: IOAPIC (id[0x08] address[0xfec00000]
gsi_base[0])
IOAPIC[0]: apic_id 8, version 32, address 0xfec00000,
GSI 0-23
ACPI: IOAPIC (id[0x09] address[0xfec80000]
gsi_base[24])
IOAPIC[1]: apic_id 9, version 32, address 0xfec80000,
GSI 24-47
ACPI: IOAPIC (id[0x0a] address[0xfec80800]
gsi_base[48])
IOAPIC[2]: apic_id 10, version 32, address 0xfec80800,
GSI 48-71
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl
dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high
level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 3 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: ro root=LABEL=/ nmi_watchdog=1
pci=routeirq console=ttyS0,115200n8 console=tty0
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
mapped IOAPIC to ffffb000 (fec80000)
mapped IOAPIC to ffffa000 (fec80800)
Initializing CPU#0
CPU 0 irqstacks, hard=c0356000 soft=c034e000
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2659.014 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7,
524288 bytes)
Inode-cache hash table entries: 65536 (order: 6,
262144 bytes)
Memory: 1034968k/1048020k available (1466k kernel
code, 12384k reserved, 693k data, 176k init, 130516k
highmem)
Checking if this processor honours the WP bit even in
supervisor mode... Ok.
Calibrating delay loop... 5242.88 BogoMIPS
(lpj=2621440)
Mount-cache hash table entries: 512 (order: 0, 4096
bytes)
CPU: After generic identify, caps: bfebfbff 00000000
00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000
00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000
00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: Intel(R) Xeon(TM) CPU 2.66GHz stepping 09
per-CPU timeslice cutoff: 1462.47 usecs.
task migration cache decay timeout: 2 msecs.
Booting processor 1/1 eip 3000
CPU 1 irqstacks, hard=c0357000 soft=c034f000
Initializing CPU#1
Calibrating delay loop... 5308.41 BogoMIPS
(lpj=2654208)
CPU: After generic identify, caps: bfebfbff 00000000
00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000
00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000
00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Xeon(TM) CPU 2.66GHz stepping 09
Booting processor 2/6 eip 3000
CPU 2 irqstacks, hard=c0358000 soft=c0350000
Initializing CPU#2
Calibrating delay loop... 5308.41 BogoMIPS
(lpj=2654208)
CPU: After generic identify, caps: bfebfbff 00000000
00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000
00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 3
CPU: After all inits, caps: bfebfbff 00000000
00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#2.
CPU2: Intel P4/Xeon Extended MCE MSRs (12) available
CPU2: Thermal monitoring enabled
CPU2: Intel(R) Xeon(TM) CPU 2.66GHz stepping 09
Booting processor 3/7 eip 3000
CPU 3 irqstacks, hard=c0359000 soft=c0351000
Initializing CPU#3
Calibrating delay loop... 5308.41 BogoMIPS
(lpj=2654208)
CPU: After generic identify, caps: bfebfbff 00000000
00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000
00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 3
CPU: After all inits, caps: bfebfbff 00000000
00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#3.
CPU3: Intel P4/Xeon Extended MCE MSRs (12) available
CPU3: Thermal monitoring enabled
CPU3: Intel(R) Xeon(TM) CPU 2.66GHz stepping 09
Total of 4 processors activated (21168.12 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
testing NMI watchdog ... OK.
checking TSC synchronization across 4 CPUs: passed.
Brought up 4 CPUs
CPU0:
domain 0: span 03
groups: 01 02
domain 1: span 0f
groups: 03 0c
CPU1:
domain 0: span 03
groups: 02 01
domain 1: span 0f
groups: 03 0c
CPU2:
domain 0: span 0c
groups: 04 08
domain 1: span 0f
groups: 0c 03
CPU3:
domain 0: span 0c
groups: 08 04
domain 1: span 0f
groups: 0c 03
checking if image is initramfs...it isn't (no cpio
magic); looks like an initrd
Freeing initrd memory: 407k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfbdd5, last
bus=5
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20041105
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table
[\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Routing Table
[\_SB_.PCI0.PCI1.PCI2._PRT]
ACPI: PCI Interrupt Routing Table
[\_SB_.PCI0.PCI1.PCI3._PRT]
ACPI: PCI Interrupt Routing Table
[\_SB_.PCI0.PCI4._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10
*11 12 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10
*11 12 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10
11 12 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10
11 12 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10
*11 12 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10
*11 12 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10
*11 12 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10
*11 12 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
PCI: Using ACPI for IRQ routing
** Routing PCI interrupts for all devices because
"pci=routeirq"
** was specified. If this was required to make a
driver work,
** please email the output of "lspci" to
bjorn.helgaas@xxxxxx
** so I can fix the driver.
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 16 (level,
low) -> IRQ 16
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level,
low) -> IRQ 19
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 18 (level,
low) -> IRQ 18
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level,
low) -> IRQ 23
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 18 (level,
low) -> IRQ 18
ACPI: PCI interrupt 0000:00:1f.3[B] -> GSI 17 (level,
low) -> IRQ 17
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 17 (level,
low) -> IRQ 17
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level,
low) -> IRQ 16
ACPI: PCI interrupt 0000:03:0e.0[A] -> GSI 24 (level,
low) -> IRQ 24
ACPI: PCI interrupt 0000:05:0c.0[A] -> GSI 20 (level,
low) -> IRQ 20
ACPI: PCI interrupt 0000:05:0d.0[A] -> GSI 21 (level,
low) -> IRQ 21
ACPI: PCI interrupt 0000:05:0d.2[B] -> GSI 22 (level,
low) -> IRQ 22
pnp: 00:0b: ioport range 0x800-0x85f could not be
reserved
pnp: 00:0b: ioport range 0xc00-0xc7f has been reserved
pnp: 00:0b: ioport range 0x860-0x8ff could not be
reserved
Simple Boot Flag at 0x7a set to 0x80
Machine check exception polling timer started.
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096
bytes)
Initializing Cryptographic API
Real Time Clock Driver v1.12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports,
IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler cfq registered
elevator: using cfq as default io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size
1024 blocksize
Uniform Multi-Platform E-IDE driver Revision:
7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes;
override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 18 (level,
low) -> IRQ 18
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings:
hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings:
hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: IC35L090AVV207-0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: HL-DT-STDVD-ROM GDR8162B, ATAPI CD/DVD-ROM drive
hdd: SONY CD-RW CRX216E, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 156250000 sectors (80000 MB) w/1821KiB Cache,
CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
device-mapper: 4.3.0-ioctl (2004-09-30) initialised:
dm-devel@xxxxxxxxxx
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind
65536)
NET: Registered protocol family 1
Starting balanced_irq
ACPI wakeup devices:
VBTN PCI0 USB0 USB1 USB2 PCI1 PCI2 PCI3 PCI4 KBD
ACPI: (supports S0 S1 S3 S4 S5)
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 176k freed
EXT3 FS on hda5, internal journal
Adding 2040212k swap on /dev/hda6. Priority:-1
extents:1
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
hdc: ATAPI 48X DVD-ROM drive, 256kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X CD-ROM CD-R/RW drive, 2048kB Cache,
UDMA(33)
IA-32 Microcode Update Driver: v1.14
<tigran@xxxxxxxxxxx>
microcode: CPU2 updated from revision 0xf to 0x2d,
date = 08112004
microcode: CPU1 updated from revision 0xf to 0x2d,
date = 08112004
microcode: CPU3 updated from revision 0xf to 0x2d,
date = 08112004
microcode: CPU0 updated from revision 0xf to 0x2d,
date = 08112004
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel E7505 Chipset.
agpgart: Maximum main memory to use for agp memory:
941M
agpgart: AGP aperture is 128M @ 0xe0000000
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 16 (level,
low) -> IRQ 16
uhci_hcd 0000:00:1d.0: Intel Corp. 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1
PCI: Setting latency timer of device 0000:00:1d.0 to
64
uhci_hcd 0000:00:1d.0: irq 16, io base 0xff80
uhci_hcd 0000:00:1d.0: new USB bus registered,
assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level,
low) -> IRQ 19
uhci_hcd 0000:00:1d.1: Intel Corp. 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2
PCI: Setting latency timer of device 0000:00:1d.1 to
64
uhci_hcd 0000:00:1d.1: irq 19, io base 0xff60
uhci_hcd 0000:00:1d.1: new USB bus registered,
assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 18 (level,
low) -> IRQ 18
uhci_hcd 0000:00:1d.2: Intel Corp. 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3
PCI: Setting latency timer of device 0000:00:1d.2 to
64
uhci_hcd 0000:00:1d.2: irq 18, io base 0xff40
uhci_hcd 0000:00:1d.2: new USB bus registered,
assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 2-1: new full speed USB device using uhci_hcd and
address 2
Linux video capture interface: v1.00
pwc Philips webcam module version 10.0.5-unofficial
loaded.
pwc Supports Philips PCA645/646, PCVC675/680/690,
PCVC720[40]/730/740/750 & PCVC830/840.
pwc Also supports the Askey VC010, various Logitech
Quickcams, Samsung MPC-C10 and MPC-C30,
pwc the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye
and Visionite VCS-UC300 and VCS-UM100.
pwc Default image size set to qcif [176x144].
pwc Enabling power save on open/close.
pwc Logitech QuickCam Zoom (new model) USB webcam
detected.
pwc Registered as /dev/video0.
usbcore: registered new driver Philips webcam
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level,
low) -> IRQ 23
ehci_hcd 0000:00:1d.7: Intel Corp. 82801DB/DBM
(ICH4/ICH4-M) USB 2.0 EHCI Controller
PCI: Setting latency timer of device 0000:00:1d.7 to
64
ehci_hcd 0000:00:1d.7: irq 23, pci mem 0xffa20800
ehci_hcd 0000:00:1d.7: new USB bus registered,
assigned bus number 4
PCI: cache line size of 128 is not supported by device
0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00,
driver 26 Oct 2004
usbcore: registered new driver snd-usb-audio
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
usb 2-1: USB disconnect, address 2
ieee1394: Initialized config rom entry `ip1394'
ohci1394: Unknown symbol hpsb_iso_wake
ohci1394: Unknown symbol hpsb_packet_received
ohci1394: Unknown symbol dma_prog_region_free
ohci1394: Unknown symbol hpsb_add_host
ohci1394: Unknown symbol dma_region_sync_for_device
ohci1394: Unknown symbol dma_prog_region_init
ohci1394: Unknown symbol dma_prog_region_alloc
ohci1394: Unknown symbol dma_region_offset_to_bus
ohci1394: Unknown symbol hpsb_alloc_host
ohci1394: Unknown symbol hpsb_selfid_complete
ohci1394: Unknown symbol hpsb_remove_host
ohci1394: Unknown symbol hpsb_iso_packet_received
ohci1394: Unknown symbol hpsb_iso_packet_sent
ohci1394: Unknown symbol hpsb_packet_sent
ohci1394: Unknown symbol dma_region_sync_for_cpu
ohci1394: Unknown symbol hpsb_selfid_received
ohci1394: Unknown symbol hpsb_bus_reset
ohci1394: Unknown symbol hpsb_iso_wake
ohci1394: Unknown symbol hpsb_packet_received
ohci1394: Unknown symbol dma_prog_region_free
ohci1394: Unknown symbol hpsb_add_host
usb 2-1: new full speed USB device using uhci_hcd and
address 3
ohci1394: Unknown symbol dma_region_sync_for_device
ohci1394: Unknown symbol dma_prog_region_init
ohci1394: Unknown symbol dma_prog_region_alloc
ohci1394: Unknown symbol dma_region_offset_to_bus
ohci1394: Unknown symbol hpsb_alloc_host
ohci1394: Unknown symbol hpsb_selfid_complete
ohci1394: Unknown symbol hpsb_remove_host
ohci1394: Unknown symbol hpsb_iso_packet_received
ohci1394: Unknown symbol hpsb_iso_packet_sent
ohci1394: Unknown symbol hpsb_packet_sent
ohci1394: Unknown symbol dma_region_sync_for_cpu
ohci1394: Unknown symbol hpsb_selfid_received
ohci1394: Unknown symbol hpsb_bus_reset
ohci1394: $Rev: 1223 $ Ben Collins
<bcollins@xxxxxxxxxx>
ACPI: PCI interrupt 0000:05:0c.0[A] -> GSI 20 (level,
low) -> IRQ 20
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20]
MMIO=[ff2ff800-ff2fffff] Max Packet=[2048]
ACPI: PCI interrupt 0000:05:0d.2[B] -> GSI 22 (level,
low) -> IRQ 22
ohci1394: fw-host1: OHCI-1394 1.1 (PCI): IRQ=[22]
MMIO=[ff2ff000-ff2ff7ff] Max Packet=[2048]
pwc Logitech QuickCam Zoom (new model) USB webcam
detected.
pwc Registered as /dev/video0.
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 17 (level,
low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.5 to
64
intel8x0_measure_ac97_clock: measured 50031 usecs
intel8x0: clocking to 48000
usb 2-1: khubd timed out on ep0out
ieee1394: Node added: ID:BUS[0-00:1023]
GUID[0050c500001076df]
ieee1394: Host added: ID:BUS[0-01:1023]
GUID[84ffffffffffff00]
ieee1394: unsolicited response packet received - no
tlabel match
usb 2-1: khubd timed out on ep0in
ieee1394: raw1394: /dev/raw1394 device initialized
video1394: Installed video1394 module
ieee1394: Host added: ID:BUS[1-00:1023]
GUID[00023c00a1037111]
Intel(R) PRO/1000 Network Driver - version
5.5.4-k2-NAPI
Copyright (c) 1999-2004 Intel Corporation.
ACPI: PCI interrupt 0000:03:0e.0[A] -> GSI 24 (level,
low) -> IRQ 24
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network
Connection
ACPI: PCI interrupt 0000:05:0d.0[A] -> GSI 21 (level,
low) -> IRQ 21
parport_pc: Ignoring new-style parameters in presence
of obsolete ones
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 1
[PCSPP,TRISTATE,COMPAT,ECP,DMA]
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller
(OHCI) Driver (PCI)
NET: Registered protocol family 17
e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps
Full Duplex
nfs warning: mount version older than kernel
SCSI subsystem initialized
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02eb2a0(lo)
IPv6 over IPv4 tunneling driver
Installing knfsd (copyright (C) 1996
okir@xxxxxxxxxxxx).
lp0: using parport0 (interrupt-driven).
/home/chris/LINUX/linux-2.6.10/drivers/usb/serial/usb-serial.c:
USB Serial support registered for Generic
usbcore: registered new driver usbserial_generic
usbcore: registered new driver usbserial
/home/chris/LINUX/linux-2.6.10/drivers/usb/serial/usb-serial.c:
USB Serial Driver core v2.0
IA-32 Microcode Update Driver v1.14 unregistered
p4-clockmod: P4/Xeon(TM) CPU On-Demand Clock
Modulation available
input: PC Speaker
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
ACPI: Power Button (FF) [PWRF]
NET: Registered protocol family 15
radeon: Ignoring new-style parameters in presence of
obsolete ones
[drm] Initialized radeon 1.13.0 20041207 on minor 0:
ATI Technologies Inc RV280 [Radeon 9200]
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level,
low) -> IRQ 16
agpgart: Found an AGP 3.0 compliant device at
0000:00:00.0.
agpgart: X passes broken AGP3 flags (1f00420f). Fixed.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x
mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x
mode
pwc Failed to restore power to the camera! (-32)
pwc Failed to set LED on/off time.
pwc set_video_mode(176x144 @ 10, palette 15).
pwc decode_size = 1.
pwc Using alternate setting 1.
[drm] Loading R200 Microcode
mask: 0000000000000001 usage: 0000000000000000
video1394_0: Iso receive DMA: 10 buffers of size
155648 allocated for a frame size 153600, each with 39
prgs
video1394_0: iso context 0 listen on channel 0
video1394_0: Iso context 0 stop talking on channel 0
pwc set_video_mode(160x120 @ 10, palette 15).
pwc decode_size = 1.
pwc Using alternate setting 1.
pwc set_video_mode(160x120 @ 10, palette 15).
pwc decode_size = 1.
pwc Using alternate setting 1.
------------------------------------------------------------------------
Module Size Used by
snd_pcm_oss 46752 0
snd_mixer_oss 17024 1 snd_pcm_oss
radeon 127520 2
i2c_algo_bit 9224 1 radeon
emu10k1_gp 3712 0
gameport 4480 1 emu10k1_gp
snd_rtctimer 3344 0
deflate 3712 0
zlib_deflate 22040 1 deflate
zlib_inflate 17664 1 deflate
twofish 38784 0
serpent 15616 0
aes_i586 38772 0
blowfish 9088 0
des 12544 0
sha256 9984 0
crypto_null 2944 0
af_key 28048 2
binfmt_misc 9864 1
eeprom 6680 0
i2c_sensor 3840 1 eeprom
button 5904 0
processor 16512 0
psmouse 19080 0
pcspkr 4300 0
p4_clockmod 5412 2
speedstep_lib 4096 1 p4_clockmod
usbserial 25576 0
lp 9736 0
nfsd 191264 9
exportfs 5760 1 nfsd
md5 4736 1
ipv6 223488 20
sd_mod 13184 0
scsi_mod 98944 1 sd_mod
autofs 13440 0
nfs 186212 1
lockd 58280 3 nfsd,nfs
sunrpc 125284 21 nfsd,nfs,lockd
af_packet 17160 0
ohci_hcd 19720 0
parport_pc 37828 1
parport 31304 2 lp,parport_pc
snd_emu10k1 86916 0
snd_util_mem 4224 1 snd_emu10k1
snd_hwdep 8224 1 snd_emu10k1
e1000 79540 0
video1394 15820 0
raw1394 25196 0
snd_intel8x0 27936 0
snd_ac97_codec 67936 2
snd_emu10k1,snd_intel8x0
i2c_i801 8204 0
i2c_core 18176 4
i2c_algo_bit,eeprom,i2c_sensor,i2c_i801
ohci1394 30084 1 video1394
ieee1394 289464 3
video1394,raw1394,ohci1394
ehci_hcd 27652 0
snd_usb_audio 60864 0
snd_pcm 79364 5
snd_pcm_oss,snd_emu10k1,snd_intel8x0,snd_ac97_codec,snd_usb_audio
snd_timer 21252 3
snd_rtctimer,snd_emu10k1,snd_pcm
snd_page_alloc 8196 3
snd_emu10k1,snd_intel8x0,snd_pcm
snd_usb_lib 11776 1 snd_usb_audio
snd_rawmidi 20256 2
snd_emu10k1,snd_usb_lib
snd_seq_device 7820 2
snd_emu10k1,snd_rawmidi
snd 45028 13
snd_pcm_oss,snd_mixer_oss,snd_rtctimer,snd_emu10k1,snd_hwdep,snd_intel8x0,snd_ac97_codec,snd_usb_audio,snd_pcm,snd_timer,snd_usb_lib,snd_rawmidi,snd_seq_device
soundcore 7904 1 snd
pwc 78448 0
videodev 8192 1 pwc
uhci_hcd 29200 0
usbcore 99704 8
usbserial,ohci_hcd,ehci_hcd,snd_usb_audio,snd_usb_lib,pwc,uhci_hcd
intel_agp 18972 1
agpgart 27308 1 intel_agp
ide_cd 36100 0
cdrom 36252 1 ide_cd
ext3 113800 2
jbd 52888 1 ext3
___________________________________________________________
ALL-NEW Yahoo! Messenger - all new features - even more fun! http://uk.messenger.yahoo.com
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/