[PATCH 8/9] dvb-ttpci: fix SMP race, budget: fixe init race, misc fixes
From: Johannes Stezenbach
Date: Sat Jan 22 2005 - 12:43:52 EST
- [DVB] dvb-ttpci: re-added support for Fujitsu-Siemens DVB-S rev 1.6 0x13c2:0x0006
- [DVB] dvb-ttpci: finally clean up debi irq/tasklet handling to make it work on SMP
- [DVB] dvb-ttpci: misc. changes to av7110_send_fw_cmd() error handling done along the way
- [DVB] dvb-ttpci: budgetpatch integrated into dvb-ttpci: enables full ts option running
in parallel with all previous functions of dvb-ttpci
- [DVB] dvb-ttpci: fix Oops provoked by insmod/rmmod test loop, patch by Emard
- [DVB] budget: Fixed start_ts_capture(): saa7146 will not issue a VPE interrupt
if VPE bit is set in PSR and VPE interrupts are enabled afterwards.
- [DVB] budget: enable satelco support. code was commented out, but actually it works, patch by Emard
- [DVB] budget: Budget patch improved driver, fixed slight packet loss by using different trigger mode
Signed-off-by: Michael Hunold <hunold@xxxxxxxxxxx>
Signed-off-by: Johannes Stezenbach <js@xxxxxxxxxxx>
diff -uraNwB linux-2.6.11-rc2/drivers/media/dvb/ttpci/av7110.c linux-2.6.11-rc2-dvb/drivers/media/dvb/ttpci/av7110.c
--- linux-2.6.11-rc2/drivers/media/dvb/ttpci/av7110.c 2005-01-20 19:54:05.000000000 +0100
+++ linux-2.6.11-rc2-dvb/drivers/media/dvb/ttpci/av7110.c 2005-01-20 19:56:38.000000000 +0100
@@ -67,6 +67,12 @@
#include "av7110_ca.h"
#include "av7110_ipack.h"
+#define TS_WIDTH 376
+#define TS_HEIGHT 512
+#define TS_BUFLEN (TS_WIDTH*TS_HEIGHT)
+#define TS_MAX_PACKETS (TS_BUFLEN/TS_SIZE)
+
+
int av7110_debug;
static int vidmode=CVBS_RGB_OUT;
@@ -75,6 +81,7 @@
static int hw_sections;
static int rgb_on;
static int volume = 255;
+static int budgetpatch = 0;
module_param_named(debug, av7110_debug, int, 0644);
MODULE_PARM_DESC(debug, "debug level (bitmask, default 0)");
@@ -91,6 +98,8 @@
" signal on SCART pin 16 to switch SCART video mode from CVBS to RGB");
module_param(volume, int, 0444);
MODULE_PARM_DESC(volume, "initial volume: default 255 (range 0-255)");
+module_param(budgetpatch, int, 0444);
+MODULE_PARM_DESC(budgetpatch, "use budget-patch hardware modification: default 0 (0 no, 1 autodetect, 2 always)");
static void restart_feeds(struct av7110 *av7110);
@@ -349,27 +358,42 @@
#endif
}
+#define DEBI_READ 0
+#define DEBI_WRITE 1
+static inline void start_debi_dma(struct av7110 *av7110, int dir,
+ unsigned long addr, unsigned int len)
+{
+ dprintk(8, "%c %08lx %u\n", dir == DEBI_READ ? 'R' : 'W', addr, len);
+ if (saa7146_wait_for_debi_done(av7110->dev, 0)) {
+ printk(KERN_ERR "%s: saa7146_wait_for_debi_done timed out\n", __FUNCTION__);
+ return;
+ }
+
+ SAA7146_ISR_CLEAR(av7110->dev, MASK_19); /* for good measure */
+ SAA7146_IER_ENABLE(av7110->dev, MASK_19);
+ if (len < 5)
+ len = 5; /* we want a real DEBI DMA */
+ if (dir == DEBI_WRITE)
+ iwdebi(av7110, DEBISWAB, addr, 0, (len + 3) & ~3);
+ else
+ irdebi(av7110, DEBISWAB, addr, 0, len);
+}
+
static void debiirq (unsigned long data)
{
struct av7110 *av7110 = (struct av7110*) data;
int type=av7110->debitype;
int handle=(type>>8)&0x1f;
-
-// dprintk(4, "%p\n",av7110);
+ unsigned int xfer = 0;
print_time("debi");
- SAA7146_IER_DISABLE(av7110->dev, MASK_19);
- SAA7146_ISR_CLEAR(av7110->dev, MASK_19);
+ dprintk(4, "type 0x%04x\n", type);
if (type==-1) {
printk("DEBI irq oops @ %ld, psr:0x%08x, ssr:0x%08x\n",
jiffies, saa7146_read(av7110->dev, PSR),
saa7146_read(av7110->dev, SSR));
- spin_lock(&av7110->debilock);
- ARM_ClearMailBox(av7110);
- ARM_ClearIrq(av7110);
- spin_unlock(&av7110->debilock);
- return;
+ goto debi_done;
}
av7110->debitype=-1;
@@ -379,22 +403,16 @@
dvb_dmx_swfilter_packets(&av7110->demux,
(const u8 *)av7110->debi_virt,
av7110->debilen/188);
- spin_lock(&av7110->debilock);
- iwdebi(av7110, DEBINOSWAP, RX_BUFF, 0, 2);
- ARM_ClearMailBox(av7110);
- spin_unlock(&av7110->debilock);
- return;
+ xfer = RX_BUFF;
+ break;
case DATA_PES_RECORD:
if (av7110->demux.recording)
av7110_record_cb(&av7110->p2t[handle],
(u8 *)av7110->debi_virt,
av7110->debilen);
- spin_lock(&av7110->debilock);
- iwdebi(av7110, DEBINOSWAP, RX_BUFF, 0, 2);
- ARM_ClearMailBox(av7110);
- spin_unlock(&av7110->debilock);
- return;
+ xfer = RX_BUFF;
+ break;
case DATA_IPMPE:
case DATA_FSECTION:
@@ -404,11 +422,8 @@
av7110->debilen, NULL, 0,
av7110->handle2filter[handle],
DMX_OK, av7110);
- spin_lock(&av7110->debilock);
- iwdebi(av7110, DEBINOSWAP, RX_BUFF, 0, 2);
- ARM_ClearMailBox(av7110);
- spin_unlock(&av7110->debilock);
- return;
+ xfer = RX_BUFF;
+ break;
case DATA_CI_GET:
{
@@ -425,11 +440,8 @@
ci_get_data(&av7110->ci_rbuffer,
av7110->debi_virt,
av7110->debilen);
- spin_lock(&av7110->debilock);
- iwdebi(av7110, DEBINOSWAP, RX_BUFF, 0, 2);
- ARM_ClearMailBox(av7110);
- spin_unlock(&av7110->debilock);
- return;
+ xfer = RX_BUFF;
+ break;
}
case DATA_COMMON_INTERFACE:
@@ -449,37 +461,35 @@
printk("\n");
}
#endif
- spin_lock(&av7110->debilock);
- iwdebi(av7110, DEBINOSWAP, RX_BUFF, 0, 2);
- ARM_ClearMailBox(av7110);
- spin_unlock(&av7110->debilock);
- return;
+ xfer = RX_BUFF;
+ break;
case DATA_DEBUG_MESSAGE:
((s8*)av7110->debi_virt)[Reserved_SIZE-1]=0;
printk("%s\n", (s8 *)av7110->debi_virt);
- spin_lock(&av7110->debilock);
- iwdebi(av7110, DEBINOSWAP, RX_BUFF, 0, 2);
- ARM_ClearMailBox(av7110);
- spin_unlock(&av7110->debilock);
- return;
+ xfer = RX_BUFF;
+ break;
case DATA_CI_PUT:
+ dprintk(4, "debi DATA_CI_PUT\n");
case DATA_MPEG_PLAY:
+ dprintk(4, "debi DATA_MPEG_PLAY\n");
case DATA_BMP_LOAD:
- spin_lock(&av7110->debilock);
- iwdebi(av7110, DEBINOSWAP, TX_BUFF, 0, 2);
- ARM_ClearMailBox(av7110);
- spin_unlock(&av7110->debilock);
- return;
+ dprintk(4, "debi DATA_BMP_LOAD\n");
+ xfer = TX_BUFF;
+ break;
default:
break;
}
+debi_done:
spin_lock(&av7110->debilock);
+ if (xfer)
+ iwdebi(av7110, DEBINOSWAP, xfer, 0, 2);
ARM_ClearMailBox(av7110);
spin_unlock(&av7110->debilock);
}
+/* irq from av7110 firmware writing the mailbox register in the DPRAM */
static void gpioirq (unsigned long data)
{
struct av7110 *av7110 = (struct av7110*) data;
@@ -487,27 +497,29 @@
int len;
if (av7110->debitype !=-1)
+ /* we shouldn't get any irq while a debi xfer is running */
printk("dvb-ttpci: GPIO0 irq oops @ %ld, psr:0x%08x, ssr:0x%08x\n",
jiffies, saa7146_read(av7110->dev, PSR),
saa7146_read(av7110->dev, SSR));
- spin_lock(&av7110->debilock);
+ if (saa7146_wait_for_debi_done(av7110->dev, 0)) {
+ printk(KERN_ERR "%s: saa7146_wait_for_debi_done timed out\n", __FUNCTION__);
+ BUG(); /* maybe we should try resetting the debi? */
+ }
+ spin_lock(&av7110->debilock);
ARM_ClearIrq(av7110);
- SAA7146_IER_DISABLE(av7110->dev, MASK_19);
- SAA7146_ISR_CLEAR(av7110->dev, MASK_19);
-
+ /* see what the av7110 wants */
av7110->debitype = irdebi(av7110, DEBINOSWAP, IRQ_STATE, 0, 2);
av7110->debilen = irdebi(av7110, DEBINOSWAP, IRQ_STATE_EXT, 0, 2);
rxbuf=irdebi(av7110, DEBINOSWAP, RX_BUFF, 0, 2);
txbuf=irdebi(av7110, DEBINOSWAP, TX_BUFF, 0, 2);
len = (av7110->debilen + 3) & ~3;
-// dprintk(8, "GPIO0 irq %d %d\n", av7110->debitype, av7110->debilen);
print_time("gpio");
+ dprintk(8, "GPIO0 irq 0x%04x %d\n", av7110->debitype, av7110->debilen);
-// dprintk(8, "GPIO0 irq %02x\n", av7110->debitype&0xff);
switch (av7110->debitype&0xff) {
case DATA_TS_PLAY:
@@ -579,16 +591,12 @@
dvb_ringbuffer_read(cibuf,av7110->debi_virt,len,0);
- wake_up(&cibuf->queue);
iwdebi(av7110, DEBINOSWAP, TX_LEN, len, 2);
iwdebi(av7110, DEBINOSWAP, IRQ_STATE_EXT, len, 2);
- saa7146_wait_for_debi_done(av7110->dev, 0);
- saa7146_write(av7110->dev, IER,
- saa7146_read(av7110->dev, IER) | MASK_19 );
- if (len < 5)
- len = 5; /* we want a real DEBI DMA */
- iwdebi(av7110, DEBISWAB, DPRAM_BASE+txbuf, 0, (len+3)&~3);
+ dprintk(8, "DMA: CI\n");
+ start_debi_dma(av7110, DEBI_WRITE, DPRAM_BASE + txbuf, len);
spin_unlock(&av7110->debilock);
+ wake_up(&cibuf->queue);
return;
}
@@ -620,22 +628,21 @@
dprintk(8, "GPIO0 PES_PLAY len=%04x\n", len);
iwdebi(av7110, DEBINOSWAP, TX_LEN, len, 2);
iwdebi(av7110, DEBINOSWAP, IRQ_STATE_EXT, len, 2);
- saa7146_wait_for_debi_done(av7110->dev, 0);
- saa7146_write(av7110->dev, IER,
- saa7146_read(av7110->dev, IER) | MASK_19 );
-
- iwdebi(av7110, DEBISWAB, DPRAM_BASE+txbuf, 0, (len+3)&~3);
+ dprintk(8, "DMA: MPEG_PLAY\n");
+ start_debi_dma(av7110, DEBI_WRITE, DPRAM_BASE + txbuf, len);
spin_unlock(&av7110->debilock);
return;
case DATA_BMP_LOAD:
len=av7110->debilen;
+ dprintk(8, "gpio DATA_BMP_LOAD len %d\n", len);
if (!len) {
av7110->bmp_state=BMP_LOADED;
iwdebi(av7110, DEBINOSWAP, IRQ_STATE_EXT, 0, 2);
iwdebi(av7110, DEBINOSWAP, TX_LEN, 0, 2);
iwdebi(av7110, DEBINOSWAP, TX_BUFF, 0, 2);
wake_up(&av7110->bmpq);
+ dprintk(8, "gpio DATA_BMP_LOAD done\n");
break;
}
if (len>av7110->bmplen)
@@ -647,12 +654,8 @@
memcpy(av7110->debi_virt, av7110->bmpbuf+av7110->bmpp, len);
av7110->bmpp+=len;
av7110->bmplen-=len;
- saa7146_wait_for_debi_done(av7110->dev, 0);
- saa7146_write(av7110->dev, IER,
- saa7146_read(av7110->dev, IER) | MASK_19 );
- if (len < 5)
- len = 5; /* we want a real DEBI DMA */
- iwdebi(av7110, DEBISWAB, DPRAM_BASE+txbuf, 0, (len+3)&~3);
+ dprintk(8, "gpio DATA_BMP_LOAD DMA len %d\n", len);
+ start_debi_dma(av7110, DEBI_WRITE, DPRAM_BASE+txbuf, len);
spin_unlock(&av7110->debilock);
return;
@@ -669,22 +672,17 @@
case DATA_TS_RECORD:
case DATA_PES_RECORD:
- saa7146_wait_for_debi_done(av7110->dev, 0);
- saa7146_write(av7110->dev, IER,
- saa7146_read(av7110->dev, IER) | MASK_19);
- irdebi(av7110, DEBISWAB, DPRAM_BASE+rxbuf, 0, len);
+ dprintk(8, "DMA: TS_REC etc.\n");
+ start_debi_dma(av7110, DEBI_READ, DPRAM_BASE+rxbuf, len);
spin_unlock(&av7110->debilock);
return;
case DATA_DEBUG_MESSAGE:
- saa7146_wait_for_debi_done(av7110->dev, 0);
if (!len || len>0xff) {
iwdebi(av7110, DEBINOSWAP, RX_BUFF, 0, 2);
break;
}
- saa7146_write(av7110->dev, IER,
- saa7146_read(av7110->dev, IER) | MASK_19);
- irdebi(av7110, DEBISWAB, Reserved, 0, len);
+ start_debi_dma(av7110, DEBI_READ, Reserved, len);
spin_unlock(&av7110->debilock);
return;
@@ -699,8 +697,8 @@
av7110->debitype, av7110->debilen);
break;
}
- ARM_ClearMailBox(av7110);
av7110->debitype=-1;
+ ARM_ClearMailBox(av7110);
spin_unlock(&av7110->debilock);
}
@@ -1145,11 +1144,107 @@
return 0;
}
+/* simplified code from budget-core.c */
+static int stop_ts_capture(struct av7110 *budget)
+{
+ dprintk(2, "budget: %p\n", budget);
+
+ if (--budget->feeding1)
+ return budget->feeding1;
+ saa7146_write(budget->dev, MC1, MASK_20); /* DMA3 off */
+ SAA7146_IER_DISABLE(budget->dev, MASK_10);
+ SAA7146_ISR_CLEAR(budget->dev, MASK_10);
+ return 0;
+}
+
+static int start_ts_capture(struct av7110 *budget)
+{
+ dprintk(2, "budget: %p\n", budget);
+
+ if (budget->feeding1)
+ return ++budget->feeding1;
+ memset(budget->grabbing, 0x00, TS_HEIGHT * TS_WIDTH);
+ budget->tsf = 0xff;
+ budget->ttbp = 0;
+ SAA7146_IER_ENABLE(budget->dev, MASK_10); /* VPE */
+ saa7146_write(budget->dev, MC1, (MASK_04 | MASK_20)); /* DMA3 on */
+ return ++budget->feeding1;
+}
+
+static int budget_start_feed(struct dvb_demux_feed *feed)
+{
+ struct dvb_demux *demux = feed->demux;
+ struct av7110 *budget = (struct av7110 *) demux->priv;
+ int status;
+
+ dprintk(2, "av7110: %p\n", budget);
+
+ spin_lock(&budget->feedlock1);
+ feed->pusi_seen = 0; /* have a clean section start */
+ status = start_ts_capture(budget);
+ spin_unlock(&budget->feedlock1);
+ return status;
+}
+
+static int budget_stop_feed(struct dvb_demux_feed *feed)
+{
+ struct dvb_demux *demux = feed->demux;
+ struct av7110 *budget = (struct av7110 *) demux->priv;
+ int status;
+
+ dprintk(2, "budget: %p\n", budget);
+
+ spin_lock(&budget->feedlock1);
+ status = stop_ts_capture(budget);
+ spin_unlock(&budget->feedlock1);
+ return status;
+}
+
+static void vpeirq(unsigned long data)
+{
+ struct av7110 *budget = (struct av7110 *) data;
+ u8 *mem = (u8 *) (budget->grabbing);
+ u32 olddma = budget->ttbp;
+ u32 newdma = saa7146_read(budget->dev, PCI_VDP3);
+
+ if (!budgetpatch) {
+ printk("av7110.c: vpeirq() called while budgetpatch disabled!"
+ " check saa7146 IER register\n");
+ BUG();
+ }
+ /* nearest lower position divisible by 188 */
+ newdma -= newdma % 188;
+
+ if (newdma >= TS_BUFLEN)
+ return;
+
+ budget->ttbp = newdma;
+
+ if (!budget->feeding1 || (newdma == olddma))
+ return;
+
+#if 0
+ /* track rps1 activity */
+ printk("vpeirq: %02x Event Counter 1 0x%04x\n",
+ mem[olddma],
+ saa7146_read(budget->dev, EC1R) & 0x3fff);
+#endif
+
+ if (newdma > olddma)
+ /* no wraparound, dump olddma..newdma */
+ dvb_dmx_swfilter_packets(&budget->demux1, mem + olddma, (newdma - olddma) / 188);
+ else {
+ /* wraparound, dump olddma..buflen and 0..newdma */
+ dvb_dmx_swfilter_packets(&budget->demux1, mem + olddma, (TS_BUFLEN - olddma) / 188);
+ dvb_dmx_swfilter_packets(&budget->demux1, mem, newdma / 188);
+ }
+}
static int av7110_register(struct av7110 *av7110)
{
int ret, i;
struct dvb_demux *dvbdemux=&av7110->demux;
+ struct dvb_demux *dvbdemux1 = &av7110->demux1;
dprintk(4, "%p\n", av7110);
@@ -1209,6 +1304,32 @@
dvb_net_init(av7110->dvb_adapter, &av7110->dvb_net, &dvbdemux->dmx);
+ if (budgetpatch) {
+ /* initialize software demux1 without its own frontend
+ * demux1 hardware is connected to frontend0 of demux0
+ */
+ dvbdemux1->priv = (void *) av7110;
+
+ dvbdemux1->filternum = 256;
+ dvbdemux1->feednum = 256;
+ dvbdemux1->start_feed = budget_start_feed;
+ dvbdemux1->stop_feed = budget_stop_feed;
+ dvbdemux1->write_to_decoder = NULL;
+
+ dvbdemux1->dmx.capabilities = (DMX_TS_FILTERING | DMX_SECTION_FILTERING |
+ DMX_MEMORY_BASED_FILTERING);
+
+ dvb_dmx_init(&av7110->demux1);
+
+ av7110->dmxdev1.filternum = 256;
+ av7110->dmxdev1.demux = &dvbdemux1->dmx;
+ av7110->dmxdev1.capabilities = 0;
+
+ dvb_dmxdev_init(&av7110->dmxdev1, av7110->dvb_adapter);
+
+ dvb_net_init(av7110->dvb_adapter, &av7110->dvb_net1, &dvbdemux1->dmx);
+ printk("dvb-ttpci: additional demux1 for budget-patch registered\n");
+ }
return 0;
}
@@ -1216,12 +1337,20 @@
static void dvb_unregister(struct av7110 *av7110)
{
struct dvb_demux *dvbdemux=&av7110->demux;
+ struct dvb_demux *dvbdemux1 = &av7110->demux1;
dprintk(4, "%p\n", av7110);
if (!av7110->registered)
return;
+ if (budgetpatch) {
+ dvb_net_release(&av7110->dvb_net1);
+ dvbdemux->dmx.close(&dvbdemux1->dmx);
+ dvb_dmxdev_release(&av7110->dmxdev1);
+ dvb_dmx_release(&av7110->demux1);
+ }
+
dvb_net_release(&av7110->dvb_net);
dvbdemux->dmx.close(&dvbdemux->dmx);
@@ -1700,6 +1829,7 @@
static struct stv0297_config nexusca_stv0297_config = {
.demod_address = 0x1C,
+ .invert = 1,
.pll_set = nexusca_stv0297_pll_set,
};
@@ -1899,12 +2029,22 @@
av7110->fe = ves1820_attach(&alps_tdbe2_config, &av7110->i2c_adap, read_pwm(av7110));
break;
+ case 0x0006: /* Fujitsu-Siemens DVB-S rev 1.6 */
+ /* Grundig 29504-451 */
+ av7110->fe = tda8083_attach(&grundig_29504_451_config, &av7110->i2c_adap);
+ if (av7110->fe) {
+ av7110->fe->ops->diseqc_send_master_cmd = av7110_diseqc_send_master_cmd;
+ av7110->fe->ops->diseqc_send_burst = av7110_diseqc_send_burst;
+ av7110->fe->ops->set_tone = av7110_set_tone;
+ }
+ break;
+
case 0x000A: // Hauppauge/TT Nexus-CA rev1.X
av7110->fe = stv0297_attach(&nexusca_stv0297_config, &av7110->i2c_adap, 0x7b);
if (av7110->fe) {
/* set TDA9819 into DVB mode */
- saa7146_setgpio(av7110->dev, 1, SAA7146_GPIO_OUTHI); // TDA9198 pin9(STD)
+ saa7146_setgpio(av7110->dev, 1, SAA7146_GPIO_OUTLO); // TDA9198 pin9(STD)
saa7146_setgpio(av7110->dev, 3, SAA7146_GPIO_OUTLO); // TDA9198 pin30(VIF)
/* tuner on this needs a slower i2c bus speed */
@@ -1940,13 +2080,169 @@
}
}
+/* Budgetpatch note:
+ * Original hardware design by Roberto Deza:
+ * There is a DVB_Wiki at
+ * http://212.227.36.83/linuxtv/wiki/index.php/Main_Page
+ * where is described this 'DVB TT Budget Patch', on Card Modding:
+ * http://212.227.36.83/linuxtv/wiki/index.php/DVB_TT_Budget_Patch
+ * On the short description there is also a link to a external file,
+ * with more details:
+ * http://perso.wanadoo.es/jesussolano/Ttf_tsc1.zip
+ *
+ * New software triggering design by Emard that works on
+ * original Roberto Deza's hardware:
+ *
+ * rps1 code for budgetpatch will copy internal HS event to GPIO3 pin.
+ * GPIO3 is in budget-patch hardware connectd to port B VSYNC
+ * HS is an internal event of 7146, accessible with RPS
+ * and temporarily raised high every n lines
+ * (n in defined in the RPS_THRESH1 counter threshold)
+ * I think HS is raised high on the beginning of the n-th line
+ * and remains high until this n-th line that triggered
+ * it is completely received. When the receiption of n-th line
+ * ends, HS is lowered.
+ *
+ * To transmit data over DMA, 7146 needs changing state at
+ * port B VSYNC pin. Any changing of port B VSYNC will
+ * cause some DMA data transfer, with more or less packets loss.
+ * It depends on the phase and frequency of VSYNC and
+ * the way of 7146 is instructed to trigger on port B (defined
+ * in DD1_INIT register, 3rd nibble from the right valid
+ * numbers are 0-7, see datasheet)
+ *
+ * The correct triggering can minimize packet loss,
+ * dvbtraffic should give this stable bandwidths:
+ * 22k transponder = 33814 kbit/s
+ * 27.5k transponder = 38045 kbit/s
+ * by experiment it is found that the best results
+ * (stable bandwidths and almost no packet loss)
+ * are obtained using DD1_INIT triggering number 2
+ * (Va at rising edge of VS Fa = HS x VS-failing forced toggle)
+ * and a VSYNC phase that occurs in the middle of DMA transfer
+ * (about byte 188*512=96256 in the DMA window).
+ *
+ * Phase of HS is still not clear to me how to control,
+ * It just happens to be so. It can be seen if one enables
+ * RPS_IRQ and print Event Counter 1 in vpeirq(). Every
+ * time RPS_INTERRUPT is called, the Event Counter 1 will
+ * increment. That's how the 7146 is programmed to do event
+ * counting in this budget-patch.c
+ * I *think* HPS setting has something to do with the phase
+ * of HS but I cant be 100% sure in that.
+ *
+ * hardware debug note: a working budget card (including budget patch)
+ * with vpeirq() interrupt setup in mode "0x90" (every 64K) will
+ * generate 3 interrupts per 25-Hz DMA frame of 2*188*512 bytes
+ * and that means 3*25=75 Hz of interrupt freqency, as seen by
+ * watch cat /proc/interrupts
+ *
+ * If this frequency is 3x lower (and data received in the DMA
+ * buffer don't start with 0x47, but in the middle of packets,
+ * whose lengths appear to be like 188 292 188 104 etc.
+ * this means VSYNC line is not connected in the hardware.
+ * (check soldering pcb and pins)
+ * The same behaviour of missing VSYNC can be duplicated on budget
+ * cards, by seting DD1_INIT trigger mode 7 in 3rd nibble.
+ */
static int av7110_attach(struct saa7146_dev* dev, struct saa7146_pci_extension_data *pci_ext)
{
struct av7110 *av7110 = NULL;
+ int length = TS_WIDTH * TS_HEIGHT;
int ret = 0;
+ int count = 0;
dprintk(4, "dev: %p\n", dev);
+ /* Set RPS_IRQ to 1 to track rps1 activity.
+ * Enabling this won't send any interrupt to PC CPU.
+ */
+#define RPS_IRQ 0
+
+ if (budgetpatch == 1) {
+ budgetpatch = 0;
+ /* autodetect the presence of budget patch
+ * this only works if saa7146 has been recently
+ * reset with with MASK_31 to MC1
+ *
+ * will wait for VBI_B event (vertical blank at port B)
+ * and will reset GPIO3 after VBI_B is detected.
+ * (GPIO3 should be raised high by CPU to
+ * test if GPIO3 will generate vertical blank signal
+ * in budget patch GPIO3 is connected to VSYNC_B
+ */
+
+ /* RESET SAA7146 */
+ saa7146_write(dev, MC1, MASK_31);
+ /* autodetection success seems to be time-dependend after reset */
+
+ /* Fix VSYNC level */
+ saa7146_setgpio(dev, 3, SAA7146_GPIO_OUTLO);
+ /* set vsync_b triggering */
+ saa7146_write(dev, DD1_STREAM_B, 0);
+ /* port B VSYNC at rising edge */
+ saa7146_write(dev, DD1_INIT, 0x00000200);
+ saa7146_write(dev, BRS_CTRL, 0x00000000); // VBI
+ saa7146_write(dev, MC2,
+ 1 * (MASK_08 | MASK_24) | // BRS control
+ 0 * (MASK_09 | MASK_25) | // a
+ 1 * (MASK_10 | MASK_26) | // b
+ 0 * (MASK_06 | MASK_22) | // HPS_CTRL1
+ 0 * (MASK_05 | MASK_21) | // HPS_CTRL2
+ 0 * (MASK_01 | MASK_15) // DEBI
+ );
+
+ /* start writing RPS1 code from beginning */
+ count = 0;
+ /* Disable RPS1 */
+ saa7146_write(dev, MC1, MASK_29);
+ /* RPS1 timeout disable */
+ saa7146_write(dev, RPS_TOV1, 0);
+ WRITE_RPS1(cpu_to_le32(CMD_PAUSE | EVT_VBI_B));
+ WRITE_RPS1(cpu_to_le32(CMD_WR_REG_MASK | (GPIO_CTRL>>2)));
+ WRITE_RPS1(cpu_to_le32(GPIO3_MSK));
+ WRITE_RPS1(cpu_to_le32(SAA7146_GPIO_OUTLO<<24));
+#if RPS_IRQ
+ /* issue RPS1 interrupt to increment counter */
+ WRITE_RPS1(cpu_to_le32(CMD_INTERRUPT));
+#endif
+ WRITE_RPS1(cpu_to_le32(CMD_STOP));
+ /* Jump to begin of RPS program as safety measure (p37) */
+ WRITE_RPS1(cpu_to_le32(CMD_JUMP));
+ WRITE_RPS1(cpu_to_le32(dev->d_rps1.dma_handle));
+
+#if RPS_IRQ
+ /* set event counter 1 source as RPS1 interrupt (0x03) (rE4 p53)
+ * use 0x03 to track RPS1 interrupts - increase by 1 every gpio3 is toggled
+ * use 0x15 to track VPE interrupts - increase by 1 every vpeirq() is called
+ */
+ saa7146_write(dev, EC1SSR, (0x03<<2) | 3 );
+ /* set event counter 1 treshold to maximum allowed value (rEC p55) */
+ saa7146_write(dev, ECT1R, 0x3fff );
+#endif
+ /* Set RPS1 Address register to point to RPS code (r108 p42) */
+ saa7146_write(dev, RPS_ADDR1, dev->d_rps1.dma_handle);
+ /* Enable RPS1, (rFC p33) */
+ saa7146_write(dev, MC1, (MASK_13 | MASK_29 ));
+
+ mdelay(10);
+ /* now send VSYNC_B to rps1 by rising GPIO3 */
+ saa7146_setgpio(dev, 3, SAA7146_GPIO_OUTHI);
+ mdelay(10);
+ /* if rps1 responded by lowering the GPIO3,
+ * then we have budgetpatch hardware
+ */
+ if ((saa7146_read(dev, GPIO_CTRL) & 0x10000000) == 0) {
+ budgetpatch = 1;
+ printk("dvb-ttpci: BUDGET-PATCH DETECTED.\n");
+ }
+ /* Disable RPS1 */
+ saa7146_write(dev, MC1, ( MASK_29 ));
+#if RPS_IRQ
+ printk("dvb-ttpci: Event Counter 1 0x%04x\n", saa7146_read(dev, EC1R) & 0x3fff );
+#endif
+ }
+
/* prepare the av7110 device struct */
if (!(av7110 = kmalloc (sizeof (struct av7110), GFP_KERNEL))) {
dprintk(1, "out of memory\n");
@@ -1980,6 +2276,7 @@
saa7146_i2c_adapter_prepare(dev, &av7110->i2c_adap, SAA7146_I2C_BUS_BIT_RATE_120); /* 275 kHz */
if (i2c_add_adapter(&av7110->i2c_adap) < 0) {
+err_no_mem:
dvb_unregister_adapter (av7110->dvb_adapter);
kfree(av7110);
return -ENOMEM;
@@ -1987,6 +2284,86 @@
ttpci_eeprom_parse_mac(&av7110->i2c_adap, av7110->dvb_adapter->proposed_mac);
+ if (budgetpatch) {
+ spin_lock_init(&av7110->feedlock1);
+ av7110->grabbing = saa7146_vmalloc_build_pgtable(
+ dev->pci, length, &av7110->pt);
+ if (!av7110->grabbing)
+ goto err_no_mem;
+ saa7146_write(dev, PCI_BT_V1, 0x1c1f101f);
+ saa7146_write(dev, BCS_CTRL, 0x80400040);
+ /* set dd1 stream a & b */
+ saa7146_write(dev, DD1_STREAM_B, 0x00000000);
+ saa7146_write(dev, DD1_INIT, 0x03000200);
+ saa7146_write(dev, MC2, (MASK_09 | MASK_25 | MASK_10 | MASK_26));
+ saa7146_write(dev, BRS_CTRL, 0x60000000);
+ saa7146_write(dev, BASE_ODD3, 0);
+ saa7146_write(dev, BASE_EVEN3, 0);
+ saa7146_write(dev, PROT_ADDR3, TS_WIDTH * TS_HEIGHT);
+ saa7146_write(dev, BASE_PAGE3, av7110->pt.dma | ME1 | 0x90);
+
+ saa7146_write(dev, PITCH3, TS_WIDTH);
+ saa7146_write(dev, NUM_LINE_BYTE3, (TS_HEIGHT << 16) | TS_WIDTH);
+
+ /* upload all */
+ saa7146_write(dev, MC2, 0x077c077c);
+ saa7146_write(dev, GPIO_CTRL, 0x000000);
+#if RPS_IRQ
+ /* set event counter 1 source as RPS1 interrupt (0x03) (rE4 p53)
+ * use 0x03 to track RPS1 interrupts - increase by 1 every gpio3 is toggled
+ * use 0x15 to track VPE interrupts - increase by 1 every vpeirq() is called
+ */
+ saa7146_write(dev, EC1SSR, (0x03<<2) | 3 );
+ /* set event counter 1 treshold to maximum allowed value (rEC p55) */
+ saa7146_write(dev, ECT1R, 0x3fff );
+#endif
+ /* Setup BUDGETPATCH MAIN RPS1 "program" (p35) */
+ count = 0;
+
+ /* Wait Source Line Counter Threshold (p36) */
+ WRITE_RPS1(cpu_to_le32(CMD_PAUSE | EVT_HS));
+ /* Set GPIO3=1 (p42) */
+ WRITE_RPS1(cpu_to_le32(CMD_WR_REG_MASK | (GPIO_CTRL>>2)));
+ WRITE_RPS1(cpu_to_le32(GPIO3_MSK));
+ WRITE_RPS1(cpu_to_le32(SAA7146_GPIO_OUTHI<<24));
+#if RPS_IRQ
+ /* issue RPS1 interrupt */
+ WRITE_RPS1(cpu_to_le32(CMD_INTERRUPT));
+#endif
+ /* Wait reset Source Line Counter Threshold (p36) */
+ WRITE_RPS1(cpu_to_le32(CMD_PAUSE | RPS_INV | EVT_HS));
+ /* Set GPIO3=0 (p42) */
+ WRITE_RPS1(cpu_to_le32(CMD_WR_REG_MASK | (GPIO_CTRL>>2)));
+ WRITE_RPS1(cpu_to_le32(GPIO3_MSK));
+ WRITE_RPS1(cpu_to_le32(SAA7146_GPIO_OUTLO<<24));
+#if RPS_IRQ
+ /* issue RPS1 interrupt */
+ WRITE_RPS1(cpu_to_le32(CMD_INTERRUPT));
+#endif
+ /* Jump to begin of RPS program (p37) */
+ WRITE_RPS1(cpu_to_le32(CMD_JUMP));
+ WRITE_RPS1(cpu_to_le32(dev->d_rps1.dma_handle));
+
+ /* Fix VSYNC level */
+ saa7146_setgpio(dev, 3, SAA7146_GPIO_OUTLO);
+ /* Set RPS1 Address register to point to RPS code (r108 p42) */
+ saa7146_write(dev, RPS_ADDR1, dev->d_rps1.dma_handle);
+ /* Set Source Line Counter Threshold, using BRS (rCC p43)
+ * It generates HS event every TS_HEIGHT lines
+ * this is related to TS_WIDTH set in register
+ * NUM_LINE_BYTE3. If NUM_LINE_BYTE low 16 bits
+ * are set to TS_WIDTH bytes (TS_WIDTH=2*188),
+ * then RPS_THRESH1 should be set to trigger
+ * every TS_HEIGHT (512) lines.
+ */
+ saa7146_write(dev, RPS_THRESH1, (TS_HEIGHT*1) | MASK_12 );
+
+ /* Enable RPS1 (rFC p33) */
+ saa7146_write(dev, MC1, (MASK_13 | MASK_29));
+
+ /* end of budgetpatch register initialization */
+ tasklet_init (&av7110->vpe_tasklet, vpeirq, (unsigned long) av7110);
+ } else {
saa7146_write(dev, PCI_BT_V1, 0x1c00101f);
saa7146_write(dev, BCS_CTRL, 0x80400040);
@@ -1998,6 +2375,7 @@
/* upload all */
saa7146_write(dev, MC2, 0x077c077c);
saa7146_write(dev, GPIO_CTRL, 0x000000);
+ }
tasklet_init (&av7110->debi_tasklet, debiirq, (unsigned long) av7110);
tasklet_init (&av7110->gpio_tasklet, gpioirq, (unsigned long) av7110);
@@ -2109,10 +2487,21 @@
struct av7110 *av7110 = (struct av7110*)saa->ext_priv;
dprintk(4, "%p\n", av7110);
- if( 0 == av7110->device_initialized ) {
+ if (!av7110->device_initialized )
return 0;
- }
+ if (budgetpatch) {
+ /* Disable RPS1 */
+ saa7146_write(saa, MC1, MASK_29);
+ /* VSYNC LOW (inactive) */
+ saa7146_setgpio(saa, 3, SAA7146_GPIO_OUTLO);
+ saa7146_write(saa, MC1, MASK_20); /* DMA3 off */
+ SAA7146_IER_DISABLE(saa, MASK_10);
+ SAA7146_ISR_CLEAR(saa, MASK_10);
+ msleep(50);
+ tasklet_kill(&av7110->vpe_tasklet);
+ saa7146_pgtable_free(saa->pci, &av7110->pt);
+ }
av7110_exit_v4l(av7110);
av7110->arm_rmmod=1;
@@ -2121,6 +2510,9 @@
while (av7110->arm_thread)
msleep(1);
+ tasklet_kill(&av7110->debi_tasklet);
+ tasklet_kill(&av7110->gpio_tasklet);
+
dvb_unregister(av7110);
SAA7146_IER_DISABLE(saa, MASK_19 | MASK_03);
@@ -2153,13 +2545,43 @@
{
struct av7110 *av7110 = dev->ext_priv;
- if (*isr & MASK_19)
+ //print_time("av7110_irq");
+
+ /* Note: Don't try to handle the DEBI error irq (MASK_18), in
+ * intel mode the timeout is asserted all the time...
+ */
+
+ if (*isr & MASK_19) {
+ //printk("av7110_irq: DEBI\n");
+ /* Note 1: The DEBI irq is level triggered: We must enable it
+ * only after we started a DMA xfer, and disable it here
+ * immediately, or it will be signalled all the time while
+ * DEBI is idle.
+ * Note 2: You would think that an irq which is masked is
+ * not signalled by the hardware. Not so for the SAA7146:
+ * An irq is signalled as long as the corresponding bit
+ * in the ISR is set, and disabling irqs just prevents the
+ * hardware from setting the ISR bit. This means a) that we
+ * must clear the ISR *after* disabling the irq (which is why
+ * we must do it here even though saa7146_core did it already),
+ * and b) that if we were to disable an edge triggered irq
+ * (like the gpio irqs sadly are) temporarily we would likely
+ * loose some. This sucks :-(
+ */
+ SAA7146_IER_DISABLE(av7110->dev, MASK_19);
+ SAA7146_ISR_CLEAR(av7110->dev, MASK_19);
tasklet_schedule (&av7110->debi_tasklet);
+ }
- if (*isr & MASK_03)
+ if (*isr & MASK_03) {
+ //printk("av7110_irq: GPIO\n");
tasklet_schedule (&av7110->gpio_tasklet);
}
+ if ((*isr & MASK_10) && budgetpatch)
+ tasklet_schedule(&av7110->vpe_tasklet);
+}
+
static struct saa7146_extension av7110_extension;
@@ -2173,8 +2595,9 @@
MAKE_AV7110_INFO(ttc_1_X, "Technotrend/Hauppauge WinTV Nexus-CA rev1.X");
MAKE_AV7110_INFO(ttc_2_X, "Technotrend/Hauppauge WinTV DVB-C rev2.X");
MAKE_AV7110_INFO(tts_2_X, "Technotrend/Hauppauge WinTV Nexus-S rev2.X");
-MAKE_AV7110_INFO(tts_1_3se, "Technotrend/Hauppauge WinTV Nexus-S rev1.3");
+MAKE_AV7110_INFO(tts_1_3se, "Technotrend/Hauppauge WinTV DVB-S rev1.3 SE");
MAKE_AV7110_INFO(fsc, "Fujitsu Siemens DVB-C");
+MAKE_AV7110_INFO(fss, "Fujitsu Siemens DVB-S rev1.6");
static struct pci_device_id pci_tbl[] = {
MAKE_EXTENSION_PCI(tts_1_X, 0x13c2, 0x0000),
@@ -2184,10 +2607,10 @@
MAKE_EXTENSION_PCI(tts_1_3se, 0x13c2, 0x1002),
MAKE_EXTENSION_PCI(fsc, 0x110a, 0x0000),
MAKE_EXTENSION_PCI(ttc_1_X, 0x13c2, 0x000a),
+ MAKE_EXTENSION_PCI(fss, 0x13c2, 0x0006),
/* MAKE_EXTENSION_PCI(???, 0x13c2, 0x0004), UNDEFINED CARD */ // Galaxis DVB PC-Sat-Carte
/* MAKE_EXTENSION_PCI(???, 0x13c2, 0x0005), UNDEFINED CARD */ // Technisat SkyStar1
-/* MAKE_EXTENSION_PCI(???, 0x13c2, 0x0006), UNDEFINED CARD */ // TT/Hauppauge WinTV Nexus-S v????
/* MAKE_EXTENSION_PCI(???, 0x13c2, 0x0008), UNDEFINED CARD */ // TT/Hauppauge WinTV DVB-T v????
/* MAKE_EXTENSION_PCI(???, 0x13c2, 0x0009), UNDEFINED CARD */ // TT/Hauppauge WinTV Nexus-CA v????
@@ -2208,7 +2631,7 @@
.attach = av7110_attach,
.detach = av7110_detach,
- .irq_mask = MASK_19|MASK_03,
+ .irq_mask = MASK_19 | MASK_03 | MASK_10,
.irq_func = av7110_irq,
};
diff -uraNwB linux-2.6.11-rc2/drivers/media/dvb/ttpci/av7110.h linux-2.6.11-rc2-dvb/drivers/media/dvb/ttpci/av7110.h
--- linux-2.6.11-rc2/drivers/media/dvb/ttpci/av7110.h 2005-01-20 19:54:05.000000000 +0100
+++ linux-2.6.11-rc2-dvb/drivers/media/dvb/ttpci/av7110.h 2005-01-20 19:56:38.000000000 +0100
@@ -115,7 +115,7 @@
int bmpp;
int bmplen;
- int bmp_state;
+ volatile int bmp_state;
#define BMP_NONE 0
#define BMP_LOADING 1
#define BMP_LOADINGS 2
@@ -158,6 +158,18 @@
struct dmx_frontend hw_frontend;
struct dmx_frontend mem_frontend;
+ /* for budget mode demux1 */
+ struct dmxdev dmxdev1;
+ struct dvb_demux demux1;
+ struct dvb_net dvb_net1;
+ spinlock_t feedlock1;
+ int feeding1;
+ u8 tsf;
+ u32 ttbp;
+ unsigned char *grabbing;
+ struct saa7146_pgtable pt;
+ struct tasklet_struct vpe_tasklet;
+
int fe_synced;
struct semaphore pid_mutex;
diff -uraNwB linux-2.6.11-rc2/drivers/media/dvb/ttpci/av7110_hw.c linux-2.6.11-rc2-dvb/drivers/media/dvb/ttpci/av7110_hw.c
--- linux-2.6.11-rc2/drivers/media/dvb/ttpci/av7110_hw.c 2005-01-20 19:55:47.000000000 +0100
+++ linux-2.6.11-rc2-dvb/drivers/media/dvb/ttpci/av7110_hw.c 2005-01-20 19:56:39.000000000 +0100
@@ -153,8 +153,10 @@
base = DRAM_START_CODE;
for (i = 0; i < blocks; i++) {
- if (waitdebi(av7110, BOOT_STATE, BOOTSTATE_BUFFER_EMPTY) < 0)
+ if (waitdebi(av7110, BOOT_STATE, BOOTSTATE_BUFFER_EMPTY) < 0) {
+ printk(KERN_ERR "dvb-ttpci: load_dram(): timeout at block %d\n", i);
return -1;
+ }
dprintk(4, "writing DRAM block %d\n", i);
mwdebi(av7110, DEBISWAB, bootblock,
((char*)data) + i * BOOT_MAX_SIZE, BOOT_MAX_SIZE);
@@ -166,8 +168,10 @@
}
if (rest > 0) {
- if (waitdebi(av7110, BOOT_STATE, BOOTSTATE_BUFFER_EMPTY) < 0)
+ if (waitdebi(av7110, BOOT_STATE, BOOTSTATE_BUFFER_EMPTY) < 0) {
+ printk(KERN_ERR "dvb-ttpci: load_dram(): timeout at last block\n");
return -1;
+ }
if (rest > 4)
mwdebi(av7110, DEBISWAB, bootblock,
((char*)data) + i * BOOT_MAX_SIZE, rest);
@@ -179,12 +183,16 @@
iwdebi(av7110, DEBINOSWAP, BOOT_SIZE, rest, 2);
iwdebi(av7110, DEBINOSWAP, BOOT_STATE, BOOTSTATE_BUFFER_FULL, 2);
}
- if (waitdebi(av7110, BOOT_STATE, BOOTSTATE_BUFFER_EMPTY) < 0)
+ if (waitdebi(av7110, BOOT_STATE, BOOTSTATE_BUFFER_EMPTY) < 0) {
+ printk(KERN_ERR "dvb-ttpci: load_dram(): timeout after last block\n");
return -1;
+ }
iwdebi(av7110, DEBINOSWAP, BOOT_SIZE, 0, 2);
iwdebi(av7110, DEBINOSWAP, BOOT_STATE, BOOTSTATE_BUFFER_FULL, 2);
- if (waitdebi(av7110, BOOT_STATE, BOOTSTATE_BOOT_COMPLETE) < 0)
+ if (waitdebi(av7110, BOOT_STATE, BOOTSTATE_BOOT_COMPLETE) < 0) {
+ printk(KERN_ERR "dvb-ttpci: load_dram(): final handshake timeout\n");
return -1;
+ }
return 0;
}
@@ -261,8 +269,11 @@
mdelay(1);
dprintk(1, "load dram code\n");
- if (load_dram(av7110, (u32 *)av7110->bin_root, av7110->size_root) < 0)
+ if (load_dram(av7110, (u32 *)av7110->bin_root, av7110->size_root) < 0) {
+ printk(KERN_ERR "dvb-ttpci: av7110_bootarm(): "
+ "load_dram() failed\n");
return -1;
+ }
saa7146_setgpio(dev, RESET_LINE, SAA7146_GPIO_OUTLO);
mdelay(1);
@@ -336,7 +347,7 @@
if (!av7110->arm_ready) {
dprintk(1, "arm not ready.\n");
- return -1;
+ return -ENXIO;
}
start = jiffies;
@@ -344,7 +355,7 @@
msleep(1);
if (time_after(jiffies, start + ARM_WAIT_FREE)) {
printk(KERN_ERR "dvb-ttpci: %s(): timeout waiting for COMMAND idle\n", __FUNCTION__);
- return -1;
+ return -ETIMEDOUT;
}
}
@@ -356,7 +367,7 @@
msleep(1);
if (time_after(jiffies, start + ARM_WAIT_SHAKE)) {
printk(KERN_ERR "dvb-ttpci: %s(): timeout waiting for HANDSHAKE_REG\n", __FUNCTION__);
- return -1;
+ return -ETIMEDOUT;
}
}
#endif
@@ -375,6 +386,13 @@
flags[0] = OSDQOver;
flags[1] = OSDQFull;
break;
+ case COMTYPE_MISC:
+ if (FW_VERSION(av7110->arm_app) >= 0x261d) {
+ type = "MSG";
+ flags[0] = GPMQOver;
+ flags[1] = GPMQBusy;
+ }
+ break;
default:
break;
}
@@ -419,18 +437,18 @@
if (time_after(jiffies, start + ARM_WAIT_FREE)) {
printk(KERN_ERR "dvb-ttpci: %s(): timeout waiting for COMMAND to complete\n",
__FUNCTION__);
- return -1;
+ return -ETIMEDOUT;
}
}
stat = rdebi(av7110, DEBINOSWAP, MSGSTATE, 0, 2);
if (stat & GPMQOver) {
printk(KERN_ERR "dvb-ttpci: %s(): GPMQOver\n", __FUNCTION__);
- return -1;
+ return -ENOSPC;
}
else if (stat & OSDQOver) {
printk(KERN_ERR "dvb-ttpci: %s(): OSDQOver\n", __FUNCTION__);
- return -1;
+ return -ENOSPC;
}
#endif
@@ -453,7 +471,8 @@
ret = __av7110_send_fw_cmd(av7110, buf, length);
up(&av7110->dcomlock);
if (ret)
- printk("dvb-ttpci: %s(): av7110_send_fw_cmd error\n", __FUNCTION__);
+ printk(KERN_ERR "dvb-ttpci: %s(): av7110_send_fw_cmd error %d\n",
+ __FUNCTION__, ret);
return ret;
}
@@ -477,7 +496,7 @@
ret = av7110_send_fw_cmd(av7110, buf, num + 2);
if (ret)
- printk("dvb-ttpci: av7110_fw_cmd error\n");
+ printk(KERN_ERR "dvb-ttpci: av7110_fw_cmd error %d\n", ret);
return ret;
}
@@ -499,7 +518,7 @@
ret = av7110_send_fw_cmd(av7110, cmd, 18);
if (ret)
- printk("dvb-ttpci: av7110_send_ci_cmd error\n");
+ printk(KERN_ERR "dvb-ttpci: av7110_send_ci_cmd error %d\n", ret);
return ret;
}
@@ -525,7 +544,7 @@
if ((err = __av7110_send_fw_cmd(av7110, request_buf, request_buf_len)) < 0) {
up(&av7110->dcomlock);
- printk("dvb-ttpci: av7110_fw_request error\n");
+ printk(KERN_ERR "dvb-ttpci: av7110_fw_request error %d\n", err);
return err;
}
@@ -579,7 +598,7 @@
int ret;
ret = av7110_fw_request(av7110, &tag, 0, buf, length);
if (ret)
- printk("dvb-ttpci: av7110_fw_query error\n");
+ printk(KERN_ERR "dvb-ttpci: av7110_fw_query error %d\n", ret);
return ret;
}
@@ -626,7 +645,7 @@
int av7110_diseqc_send(struct av7110 *av7110, int len, u8 *msg, unsigned long burst)
{
- int i;
+ int i, ret;
u16 buf[18] = { ((COMTYPE_AUDIODAC << 8) + SendDiSEqC),
16, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 };
@@ -646,8 +665,8 @@
for (i = 0; i < len; i++)
buf[i + 4] = msg[i];
- if (av7110_send_fw_cmd(av7110, buf, 18))
- printk("dvb-ttpci: av7110_diseqc_send error\n");
+ if ((ret = av7110_send_fw_cmd(av7110, buf, 18)))
+ printk(KERN_ERR "dvb-ttpci: av7110_diseqc_send error %d\n", ret);
return 0;
}
@@ -741,7 +775,7 @@
ret = __av7110_send_fw_cmd(av7110, cbuf, 5);
up(&av7110->dcomlock);
if (ret)
- printk("dvb-ttpci: WriteText error\n");
+ printk(KERN_ERR "dvb-ttpci: WriteText error %d\n", ret);
return ret;
}
@@ -808,7 +842,8 @@
ret = wait_event_interruptible_timeout(av7110->bmpq, av7110->bmp_state != BMP_LOADING, HZ);
if (ret == -ERESTARTSYS || ret == 0) {
- printk("dvb-ttpci: warning: timeout waiting in %s()\n", __FUNCTION__);
+ printk("dvb-ttpci: warning: timeout waiting in LoadBitmap: %d, %d\n",
+ ret, av7110->bmp_state);
av7110->bmp_state = BMP_NONE;
return -1;
}
@@ -850,6 +885,7 @@
}
}
av7110->bmplen += 1024;
+ dprintk(4, "av7110_fw_cmd: LoadBmp size %d\n", av7110->bmplen);
return av7110_fw_cmd(av7110, COMTYPE_OSD, LoadBmp, 3, format, dx, dy);
}
@@ -861,11 +897,13 @@
BUG_ON (av7110->bmp_state == BMP_NONE);
- ret = wait_event_interruptible_timeout(av7110->bmpq, av7110->bmp_state != BMP_LOADING, HZ);
+ ret = wait_event_interruptible_timeout(av7110->bmpq,
+ av7110->bmp_state != BMP_LOADING, 10*HZ);
if (ret == -ERESTARTSYS || ret == 0) {
- printk("dvb-ttpci: warning: timeout waiting in %s()\n", __FUNCTION__);
+ printk("dvb-ttpci: warning: timeout waiting in BlitBitmap: %d, %d\n",
+ ret, av7110->bmp_state);
av7110->bmp_state = BMP_NONE;
- return -1;
+ return (ret == 0) ? -ETIMEDOUT : ret;
}
BUG_ON (av7110->bmp_state != BMP_LOADED);
@@ -943,6 +981,7 @@
{
uint w, h, bpp, bpl, size, lpb, bnum, brest;
int i;
+ int rc;
w = x1 - x0 + 1;
h = y1 - y0 + 1;
@@ -958,15 +997,23 @@
brest = size - bnum * lpb * bpl;
for (i = 0; i < bnum; i++) {
- LoadBitmap(av7110, bpp2bit[av7110->osdbpp[av7110->osdwin]],
+ rc = LoadBitmap(av7110, bpp2bit[av7110->osdbpp[av7110->osdwin]],
w, lpb, inc, data);
- BlitBitmap(av7110, av7110->osdwin, x0, y0 + i * lpb, 0);
+ if (rc)
+ return rc;
+ rc = BlitBitmap(av7110, av7110->osdwin, x0, y0 + i * lpb, 0);
+ if (rc)
+ return rc;
data += lpb * inc;
}
if (brest) {
- LoadBitmap(av7110, bpp2bit[av7110->osdbpp[av7110->osdwin]],
+ rc = LoadBitmap(av7110, bpp2bit[av7110->osdbpp[av7110->osdwin]],
w, brest / bpl, inc, data);
- BlitBitmap(av7110, av7110->osdwin, x0, y0 + bnum * lpb, 0);
+ if (rc)
+ return rc;
+ rc = BlitBitmap(av7110, av7110->osdwin, x0, y0 + bnum * lpb, 0);
+ if (rc)
+ return rc;
}
ReleaseBitmap(av7110);
return 0;
@@ -1019,7 +1066,7 @@
goto out;
} else {
int i, len = dc->x0-dc->color+1;
- u8 __user *colors = (u8 __user *)dc->data;
+ u8 __user *colors = (u8 *)dc->data;
u8 r, g, b, blend;
for (i = 0; i<len; i++) {
@@ -1048,7 +1095,7 @@
dc->y1 = dc->y0;
/* fall through */
case OSD_SetBlock:
- OSDSetBlock(av7110, dc->x0, dc->y0, dc->x1, dc->y1, dc->color, dc->data);
+ ret = OSDSetBlock(av7110, dc->x0, dc->y0, dc->x1, dc->y1, dc->color, dc->data);
goto out;
case OSD_FillRow:
DrawBlock(av7110, av7110->osdwin, dc->x0, dc->y0,
diff -uraNwB linux-2.6.11-rc2/drivers/media/dvb/ttpci/av7110_v4l.c linux-2.6.11-rc2-dvb/drivers/media/dvb/ttpci/av7110_v4l.c
--- linux-2.6.11-rc2/drivers/media/dvb/ttpci/av7110_v4l.c 2005-01-20 19:54:05.000000000 +0100
+++ linux-2.6.11-rc2-dvb/drivers/media/dvb/ttpci/av7110_v4l.c 2005-01-20 19:56:39.000000000 +0100
@@ -250,7 +248,7 @@
if (ves1820_writereg(dev, 0x09, 0x0f, 0x20))
dprintk(1, "setting band in demodulator failed.\n");
} else if (av7110->analog_tuner_flags & ANALOG_TUNER_STV0297) {
- saa7146_setgpio(dev, 1, SAA7146_GPIO_OUTHI); // TDA9198 pin9(STD)
+ saa7146_setgpio(dev, 1, SAA7146_GPIO_OUTLO); // TDA9198 pin9(STD)
saa7146_setgpio(dev, 3, SAA7146_GPIO_OUTLO); // TDA9198 pin30(VIF)
}
}
@@ -591,7 +589,7 @@
if (ves1820_writereg(av7110->dev, 0x09, 0x0f, 0x20))
dprintk(1, "setting band in demodulator failed.\n");
} else if (av7110->analog_tuner_flags & ANALOG_TUNER_STV0297) {
- saa7146_setgpio(av7110->dev, 1, SAA7146_GPIO_OUTHI); // TDA9198 pin9(STD)
+ saa7146_setgpio(av7110->dev, 1, SAA7146_GPIO_OUTLO); // TDA9198 pin9(STD)
saa7146_setgpio(av7110->dev, 3, SAA7146_GPIO_OUTLO); // TDA9198 pin30(VIF)
}
diff -uraNwB linux-2.6.11-rc2/drivers/media/dvb/ttpci/budget.c linux-2.6.11-rc2-dvb/drivers/media/dvb/ttpci/budget.c
--- linux-2.6.11-rc2/drivers/media/dvb/ttpci/budget.c 2005-01-20 19:54:05.000000000 +0100
+++ linux-2.6.11-rc2-dvb/drivers/media/dvb/ttpci/budget.c 2005-01-20 19:56:39.000000000 +0100
@@ -414,7 +412,7 @@
{
switch(budget->dev->pci->subsystem_device) {
case 0x1003: // Hauppauge/TT Nova budget (stv0299/ALPS BSRU6(tsa5059) OR ves1893/ALPS BSRV2(sp5659))
-
+ case 0x1013:
// try the ALPS BSRV2 first of all
budget->dvb_frontend = ves1x93_attach(&alps_bsrv2_config, &budget->i2c_adap);
if (budget->dvb_frontend) {
@@ -522,14 +517,14 @@
MAKE_BUDGET_INFO(ttbs, "TT-Budget/WinTV-NOVA-S PCI", BUDGET_TT);
MAKE_BUDGET_INFO(ttbc, "TT-Budget/WinTV-NOVA-C PCI", BUDGET_TT);
MAKE_BUDGET_INFO(ttbt, "TT-Budget/WinTV-NOVA-T PCI", BUDGET_TT);
-/* MAKE_BUDGET_INFO(satel, "SATELCO Multimedia PCI", BUDGET_TT_HW_DISEQC); UNDEFINED HARDWARE - mail linuxtv.org list */
+MAKE_BUDGET_INFO(satel, "SATELCO Multimedia PCI", BUDGET_TT_HW_DISEQC);
MAKE_BUDGET_INFO(fsacs, "Fujitsu Siemens Activy Budget-S PCI", BUDGET_FS_ACTIVY);
static struct pci_device_id pci_tbl[] = {
MAKE_EXTENSION_PCI(ttbs, 0x13c2, 0x1003),
MAKE_EXTENSION_PCI(ttbc, 0x13c2, 0x1004),
MAKE_EXTENSION_PCI(ttbt, 0x13c2, 0x1005),
-/* MAKE_EXTENSION_PCI(satel, 0x13c2, 0x1013), UNDEFINED HARDWARE */
+ MAKE_EXTENSION_PCI(satel, 0x13c2, 0x1013),
MAKE_EXTENSION_PCI(fsacs, 0x1131, 0x4f61),
{
.vendor = 0,
diff -uraNwB linux-2.6.11-rc2/drivers/media/dvb/ttpci/budget-core.c linux-2.6.11-rc2-dvb/drivers/media/dvb/ttpci/budget-core.c
--- linux-2.6.11-rc2/drivers/media/dvb/ttpci/budget-core.c 2005-01-20 19:54:05.000000000 +0100
+++ linux-2.6.11-rc2-dvb/drivers/media/dvb/ttpci/budget-core.c 2005-01-20 19:56:39.000000000 +0100
@@ -89,11 +87,18 @@
* Pitch: 188, NumBytes3: 188, NumLines3: 1024
*/
- if (budget->card->type == BUDGET_FS_ACTIVY) {
+ switch(budget->card->type) {
+ case BUDGET_FS_ACTIVY:
saa7146_write(dev, DD1_INIT, 0x04000000);
saa7146_write(dev, MC2, (MASK_09 | MASK_25));
saa7146_write(dev, BRS_CTRL, 0x00000000);
- } else {
+ break;
+ case BUDGET_PATCH:
+ saa7146_write(dev, DD1_INIT, 0x00000200);
+ saa7146_write(dev, MC2, (MASK_10 | MASK_26));
+ saa7146_write(dev, BRS_CTRL, 0x60000000);
+ break;
+ default:
if (budget->video_port == BUDGET_VIDEO_PORTA) {
saa7146_write(dev, DD1_INIT, 0x06000200);
saa7146_write(dev, MC2, (MASK_09 | MASK_25 | MASK_10 | MASK_26));
@@ -122,9 +127,10 @@
}
saa7146_write(dev, MC2, (MASK_04 | MASK_20));
- saa7146_write(dev, MC1, (MASK_04 | MASK_20)); // DMA3 on
- SAA7146_IER_ENABLE(budget->dev, MASK_10); // VPE
+ SAA7146_ISR_CLEAR(budget->dev, MASK_10); /* VPE */
+ SAA7146_IER_ENABLE(budget->dev, MASK_10); /* VPE */
+ saa7146_write(dev, MC1, (MASK_04 | MASK_20)); /* DMA3 on */
return ++budget->feeding;
}
@@ -249,6 +254,7 @@
return -EINVAL;
spin_lock(&budget->feedlock);
+ feed->pusi_seen = 0; /* have a clean section start */
status = start_ts_capture (budget);
spin_unlock(&budget->feedlock);
return status;
diff -uraNwB linux-2.6.11-rc2/drivers/media/dvb/ttpci/budget-patch.c linux-2.6.11-rc2-dvb/drivers/media/dvb/ttpci/budget-patch.c
--- linux-2.6.11-rc2/drivers/media/dvb/ttpci/budget-patch.c 2005-01-20 19:54:05.000000000 +0100
+++ linux-2.6.11-rc2-dvb/drivers/media/dvb/ttpci/budget-patch.c 2005-01-20 19:56:39.000000000 +0100
@@ -41,34 +41,127 @@
static struct saa7146_extension budget_extension;
-MAKE_BUDGET_INFO(fs_1_3,"Siemens/Technotrend/Hauppauge PCI rev1.3+Budget_Patch", BUDGET_PATCH);
+MAKE_BUDGET_INFO(ttbp, "TT-Budget/Patch DVB-S 1.x PCI", BUDGET_PATCH);
+//MAKE_BUDGET_INFO(satel,"TT-Budget/Patch SATELCO PCI", BUDGET_TT_HW_DISEQC);
static struct pci_device_id pci_tbl[] = {
- MAKE_EXTENSION_PCI(fs_1_3,0x13c2, 0x0000),
+ MAKE_EXTENSION_PCI(ttbp,0x13c2, 0x0000),
+// MAKE_EXTENSION_PCI(satel, 0x13c2, 0x1013),
{
.vendor = 0,
}
};
-static int budget_wdebi(struct budget_patch *budget, u32 config, int addr, u32 val, int count)
+/* those lines are for budget-patch to be tried
+** on a true budget card and observe the
+** behaviour of VSYNC generated by rps1.
+** this code was shamelessly copy/pasted from budget.c
+*/
+static void gpio_Set22K (struct budget *budget, int state)
+{
+ struct saa7146_dev *dev=budget->dev;
+ dprintk(2, "budget: %p\n", budget);
+ saa7146_setgpio(dev, 3, (state ? SAA7146_GPIO_OUTHI : SAA7146_GPIO_OUTLO));
+}
+
+/* Diseqc functions only for TT Budget card */
+/* taken from the Skyvision DVB driver by
+ Ralph Metzler <rjkm@xxxxxxxxxxxxxx> */
+
+static void DiseqcSendBit (struct budget *budget, int data)
+{
+ struct saa7146_dev *dev=budget->dev;
+ dprintk(2, "budget: %p\n", budget);
+
+ saa7146_setgpio(dev, 3, SAA7146_GPIO_OUTHI);
+ udelay(data ? 500 : 1000);
+ saa7146_setgpio(dev, 3, SAA7146_GPIO_OUTLO);
+ udelay(data ? 1000 : 500);
+}
+
+static void DiseqcSendByte (struct budget *budget, int data)
+{
+ int i, par=1, d;
+
+ dprintk(2, "budget: %p\n", budget);
+
+ for (i=7; i>=0; i--) {
+ d = (data>>i)&1;
+ par ^= d;
+ DiseqcSendBit(budget, d);
+ }
+
+ DiseqcSendBit(budget, par);
+}
+
+static int SendDiSEqCMsg (struct budget *budget, int len, u8 *msg, unsigned long burst)
{
struct saa7146_dev *dev=budget->dev;
+ int i;
dprintk(2, "budget: %p\n", budget);
- if (count <= 0 || count > 4)
- return -1;
+ saa7146_setgpio(dev, 3, SAA7146_GPIO_OUTLO);
+ mdelay(16);
+
+ for (i=0; i<len; i++)
+ DiseqcSendByte(budget, msg[i]);
+
+ mdelay(16);
+
+ if (burst!=-1) {
+ if (burst)
+ DiseqcSendByte(budget, 0xff);
+ else {
+ saa7146_setgpio(dev, 3, SAA7146_GPIO_OUTHI);
+ udelay(12500);
+ saa7146_setgpio(dev, 3, SAA7146_GPIO_OUTLO);
+ }
+ msleep(20);
+ }
+
+ return 0;
+}
+
+/* shamelessly copy/pasted from budget.c
+*/
+static int budget_set_tone(struct dvb_frontend* fe, fe_sec_tone_mode_t tone)
+{
+ struct budget* budget = (struct budget*) fe->dvb->priv;
+
+ switch (tone) {
+ case SEC_TONE_ON:
+ gpio_Set22K (budget, 1);
+ break;
+
+ case SEC_TONE_OFF:
+ gpio_Set22K (budget, 0);
+ break;
+
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
- saa7146_write(dev, DEBI_CONFIG, config);
+static int budget_diseqc_send_master_cmd(struct dvb_frontend* fe, struct dvb_diseqc_master_cmd* cmd)
+{
+ struct budget* budget = (struct budget*) fe->dvb->priv;
- saa7146_write(dev, DEBI_AD, val );
- saa7146_write(dev, DEBI_COMMAND, (count << 17) | (addr & 0xffff));
- saa7146_write(dev, MC2, (2 << 16) | 2);
- mdelay(5);
+ SendDiSEqCMsg (budget, cmd->msg_len, cmd->msg, 0);
return 0;
}
+static int budget_diseqc_send_burst(struct dvb_frontend* fe, fe_sec_mini_cmd_t minicmd)
+{
+ struct budget* budget = (struct budget*) fe->dvb->priv;
+
+ SendDiSEqCMsg (budget, 0, NULL, minicmd);
+
+ return 0;
+}
static int budget_av7110_send_fw_cmd(struct budget_patch *budget, u16* buf, int length)
{
@@ -77,14 +170,17 @@
dprintk(2, "budget: %p\n", budget);
for (i = 2; i < length; i++)
- budget_wdebi(budget, DEBINOSWAP, COMMAND + 2*i, (u32) buf[i], 2);
-
+ {
+ ttpci_budget_debiwrite(budget, DEBINOSWAP, COMMAND + 2*i, 2, (u32) buf[i], 0,0);
+ msleep(5);
+ }
if (length)
- budget_wdebi(budget, DEBINOSWAP, COMMAND + 2, (u32) buf[1], 2);
+ ttpci_budget_debiwrite(budget, DEBINOSWAP, COMMAND + 2, 2, (u32) buf[1], 0,0);
else
- budget_wdebi(budget, DEBINOSWAP, COMMAND + 2, 0, 2);
-
- budget_wdebi(budget, DEBINOSWAP, COMMAND, (u32) buf[0], 2);
+ ttpci_budget_debiwrite(budget, DEBINOSWAP, COMMAND + 2, 2, 0, 0,0);
+ msleep(5);
+ ttpci_budget_debiwrite(budget, DEBINOSWAP, COMMAND, 2, (u32) buf[0], 0,0);
+ msleep(5);
return 0;
}
@@ -319,6 +415,7 @@
{
switch(budget->dev->pci->subsystem_device) {
case 0x0000: // Hauppauge/TT WinTV DVB-S rev1.X
+ case 0x1013: // SATELCO Multimedia PCI
// try the ALPS BSRV2 first of all
budget->dvb_frontend = ves1x93_attach(&alps_bsrv2_config, &budget->i2c_adap);
@@ -332,18 +429,18 @@
// try the ALPS BSRU6 now
budget->dvb_frontend = stv0299_attach(&alps_bsru6_config, &budget->i2c_adap);
if (budget->dvb_frontend) {
- budget->dvb_frontend->ops->diseqc_send_master_cmd = budget_patch_diseqc_send_master_cmd;
- budget->dvb_frontend->ops->diseqc_send_burst = budget_patch_diseqc_send_burst;
- budget->dvb_frontend->ops->set_tone = budget_patch_set_tone;
+ budget->dvb_frontend->ops->diseqc_send_master_cmd = budget_diseqc_send_master_cmd;
+ budget->dvb_frontend->ops->diseqc_send_burst = budget_diseqc_send_burst;
+ budget->dvb_frontend->ops->set_tone = budget_set_tone;
break;
}
// Try the grundig 29504-451
budget->dvb_frontend = tda8083_attach(&grundig_29504_451_config, &budget->i2c_adap);
if (budget->dvb_frontend) {
- budget->dvb_frontend->ops->diseqc_send_master_cmd = budget_patch_diseqc_send_master_cmd;
- budget->dvb_frontend->ops->diseqc_send_burst = budget_patch_diseqc_send_burst;
- budget->dvb_frontend->ops->set_tone = budget_patch_set_tone;
+ budget->dvb_frontend->ops->diseqc_send_master_cmd = budget_diseqc_send_master_cmd;
+ budget->dvb_frontend->ops->diseqc_send_burst = budget_diseqc_send_burst;
+ budget->dvb_frontend->ops->set_tone = budget_set_tone;
break;
}
break;
@@ -365,23 +462,120 @@
}
}
+/* written by Emard */
static int budget_patch_attach (struct saa7146_dev* dev, struct saa7146_pci_extension_data *info)
{
struct budget_patch *budget;
int err;
int count = 0;
+ int detected = 0;
- if (!(budget = kmalloc (sizeof(struct budget_patch), GFP_KERNEL)))
- return -ENOMEM;
+#define PATCH_RESET 0
+#define RPS_IRQ 0
+#define HPS_SETUP 0
+#if PATCH_RESET
+ saa7146_write(dev, MC1, MASK_31);
+ msleep(40);
+#endif
+#if HPS_SETUP
+ // initialize registers. Better to have it like this
+ // than leaving something unconfigured
+ saa7146_write(dev, DD1_STREAM_B, 0);
+ // port B VSYNC at rising edge
+ saa7146_write(dev, DD1_INIT, 0x00000200); // have this in budget-core too!
+ saa7146_write(dev, BRS_CTRL, 0x00000000); // VBI
+
+ // debi config
+ // saa7146_write(dev, DEBI_CONFIG, MASK_30|MASK_28|MASK_18);
+
+ // zero all HPS registers
+ saa7146_write(dev, HPS_H_PRESCALE, 0); // r68
+ saa7146_write(dev, HPS_H_SCALE, 0); // r6c
+ saa7146_write(dev, BCS_CTRL, 0); // r70
+ saa7146_write(dev, HPS_V_SCALE, 0); // r60
+ saa7146_write(dev, HPS_V_GAIN, 0); // r64
+ saa7146_write(dev, CHROMA_KEY_RANGE, 0); // r74
+ saa7146_write(dev, CLIP_FORMAT_CTRL, 0); // r78
+ // Set HPS prescaler for port B input
+ saa7146_write(dev, HPS_CTRL, (1<<30) | (0<<29) | (1<<28) | (0<<12) );
+ saa7146_write(dev, MC2,
+ 0 * (MASK_08 | MASK_24) | // BRS control
+ 0 * (MASK_09 | MASK_25) | // a
+ 0 * (MASK_10 | MASK_26) | // b
+ 1 * (MASK_06 | MASK_22) | // HPS_CTRL1
+ 1 * (MASK_05 | MASK_21) | // HPS_CTRL2
+ 0 * (MASK_01 | MASK_15) // DEBI
+ );
+#endif
+ // Disable RPS1 and RPS0
+ saa7146_write(dev, MC1, ( MASK_29 | MASK_28));
+ // RPS1 timeout disable
+ saa7146_write(dev, RPS_TOV1, 0);
+
+ // code for autodetection
+ // will wait for VBI_B event (vertical blank at port B)
+ // and will reset GPIO3 after VBI_B is detected.
+ // (GPIO3 should be raised high by CPU to
+ // test if GPIO3 will generate vertical blank signal
+ // in budget patch GPIO3 is connected to VSYNC_B
+ count = 0;
+#if 0
+ WRITE_RPS1(cpu_to_le32(CMD_UPLOAD |
+ MASK_10 | MASK_09 | MASK_08 | MASK_06 | MASK_05 | MASK_04 | MASK_03 | MASK_02 ));
+#endif
+ WRITE_RPS1(cpu_to_le32(CMD_PAUSE | EVT_VBI_B));
+ WRITE_RPS1(cpu_to_le32(CMD_WR_REG_MASK | (GPIO_CTRL>>2)));
+ WRITE_RPS1(cpu_to_le32(GPIO3_MSK));
+ WRITE_RPS1(cpu_to_le32(SAA7146_GPIO_OUTLO<<24));
+#if RPS_IRQ
+ // issue RPS1 interrupt to increment counter
+ WRITE_RPS1(cpu_to_le32(CMD_INTERRUPT));
+ // at least a NOP is neede between two interrupts
+ WRITE_RPS1(cpu_to_le32(CMD_NOP));
+ // interrupt again
+ WRITE_RPS1(cpu_to_le32(CMD_INTERRUPT));
+#endif
+ WRITE_RPS1(cpu_to_le32(CMD_STOP));
+
+#if RPS_IRQ
+ // set event counter 1 source as RPS1 interrupt (0x03) (rE4 p53)
+ // use 0x03 to track RPS1 interrupts - increase by 1 every gpio3 is toggled
+ // use 0x15 to track VPE interrupts - increase by 1 every vpeirq() is called
+ saa7146_write(dev, EC1SSR, (0x03<<2) | 3 );
+ // set event counter 1 treshold to maximum allowed value (rEC p55)
+ saa7146_write(dev, ECT1R, 0x3fff );
+#endif
+ // Fix VSYNC level
+ saa7146_setgpio(dev, 3, SAA7146_GPIO_OUTLO);
+ // Set RPS1 Address register to point to RPS code (r108 p42)
+ saa7146_write(dev, RPS_ADDR1, dev->d_rps1.dma_handle);
+ // Enable RPS1, (rFC p33)
+ saa7146_write(dev, MC1, (MASK_13 | MASK_29 ));
- dprintk(2, "budget: %p\n", budget);
- if ((err = ttpci_budget_init (budget, dev, info, THIS_MODULE))) {
- kfree (budget);
- return err;
- }
+ mdelay(50);
+ saa7146_setgpio(dev, 3, SAA7146_GPIO_OUTHI);
+ mdelay(150);
+
+
+ if( (saa7146_read(dev, GPIO_CTRL) & 0x10000000) == 0)
+ detected = 1;
+
+#if RPS_IRQ
+ printk("Event Counter 1 0x%04x\n", saa7146_read(dev, EC1R) & 0x3fff );
+#endif
+ // Disable RPS1
+ saa7146_write(dev, MC1, ( MASK_29 ));
+
+ if(detected == 0)
+ printk("budget-patch not detected or saa7146 in non-default state.\n"
+ "try enabling ressetting of 7146 with MASK_31 in MC1 register\n");
+
+ else
+ printk("BUDGET-PATCH DETECTED.\n");
-/*
+
+/* OLD (Original design by Roberto Deza):
** This code will setup the SAA7146_RPS1 to generate a square
** wave on GPIO3, changing when a field (TS_HEIGHT/2 "lines" of
** TS_WIDTH packets) has been acquired on SAA7146_D1B video port;
@@ -393,24 +587,85 @@
** which seems that can be done perfectly without this :-)).
*/
+/* New design (By Emard)
+** this rps1 code will copy internal HS event to GPIO3 pin.
+** GPIO3 is in budget-patch hardware connectd to port B VSYNC
+
+** HS is an internal event of 7146, accessible with RPS
+** and temporarily raised high every n lines
+** (n in defined in the RPS_THRESH1 counter threshold)
+** I think HS is raised high on the beginning of the n-th line
+** and remains high until this n-th line that triggered
+** it is completely received. When the receiption of n-th line
+** ends, HS is lowered.
+
+** To transmit data over DMA, 7146 needs changing state at
+** port B VSYNC pin. Any changing of port B VSYNC will
+** cause some DMA data transfer, with more or less packets loss.
+** It depends on the phase and frequency of VSYNC and
+** the way of 7146 is instructed to trigger on port B (defined
+** in DD1_INIT register, 3rd nibble from the right valid
+** numbers are 0-7, see datasheet)
+**
+** The correct triggering can minimize packet loss,
+** dvbtraffic should give this stable bandwidths:
+** 22k transponder = 33814 kbit/s
+** 27.5k transponder = 38045 kbit/s
+** by experiment it is found that the best results
+** (stable bandwidths and almost no packet loss)
+** are obtained using DD1_INIT triggering number 2
+** (Va at rising edge of VS Fa = HS x VS-failing forced toggle)
+** and a VSYNC phase that occurs in the middle of DMA transfer
+** (about byte 188*512=96256 in the DMA window).
+**
+** Phase of HS is still not clear to me how to control,
+** It just happens to be so. It can be seen if one enables
+** RPS_IRQ and print Event Counter 1 in vpeirq(). Every
+** time RPS_INTERRUPT is called, the Event Counter 1 will
+** increment. That's how the 7146 is programmed to do event
+** counting in this budget-patch.c
+** I *think* HPS setting has something to do with the phase
+** of HS but I cant be 100% sure in that.
+
+** hardware debug note: a working budget card (including budget patch)
+** with vpeirq() interrupt setup in mode "0x90" (every 64K) will
+** generate 3 interrupts per 25-Hz DMA frame of 2*188*512 bytes
+** and that means 3*25=75 Hz of interrupt freqency, as seen by
+** watch cat /proc/interrupts
+**
+** If this frequency is 3x lower (and data received in the DMA
+** buffer don't start with 0x47, but in the middle of packets,
+** whose lengths appear to be like 188 292 188 104 etc.
+** this means VSYNC line is not connected in the hardware.
+** (check soldering pcb and pins)
+** The same behaviour of missing VSYNC can be duplicated on budget
+** cards, by seting DD1_INIT trigger mode 7 in 3rd nibble.
+*/
+
// Setup RPS1 "program" (p35)
+ count = 0;
+
- // Wait reset Source Line Counter Threshold (p36)
- WRITE_RPS1(cpu_to_le32(CMD_PAUSE | RPS_INV | EVT_HS));
// Wait Source Line Counter Threshold (p36)
WRITE_RPS1(cpu_to_le32(CMD_PAUSE | EVT_HS));
// Set GPIO3=1 (p42)
WRITE_RPS1(cpu_to_le32(CMD_WR_REG_MASK | (GPIO_CTRL>>2)));
WRITE_RPS1(cpu_to_le32(GPIO3_MSK));
WRITE_RPS1(cpu_to_le32(SAA7146_GPIO_OUTHI<<24));
+#if RPS_IRQ
+ // issue RPS1 interrupt
+ WRITE_RPS1(cpu_to_le32(CMD_INTERRUPT));
+#endif
// Wait reset Source Line Counter Threshold (p36)
WRITE_RPS1(cpu_to_le32(CMD_PAUSE | RPS_INV | EVT_HS));
- // Wait Source Line Counter Threshold
- WRITE_RPS1(cpu_to_le32(CMD_PAUSE | EVT_HS));
// Set GPIO3=0 (p42)
WRITE_RPS1(cpu_to_le32(CMD_WR_REG_MASK | (GPIO_CTRL>>2)));
WRITE_RPS1(cpu_to_le32(GPIO3_MSK));
WRITE_RPS1(cpu_to_le32(SAA7146_GPIO_OUTLO<<24));
+#if RPS_IRQ
+ // issue RPS1 interrupt
+ WRITE_RPS1(cpu_to_le32(CMD_INTERRUPT));
+#endif
// Jump to begin of RPS program (p37)
WRITE_RPS1(cpu_to_le32(CMD_JUMP));
WRITE_RPS1(cpu_to_le32(dev->d_rps1.dma_handle));
@@ -420,10 +675,31 @@
// Set RPS1 Address register to point to RPS code (r108 p42)
saa7146_write(dev, RPS_ADDR1, dev->d_rps1.dma_handle);
// Set Source Line Counter Threshold, using BRS (rCC p43)
- saa7146_write(dev, RPS_THRESH1, ((TS_HEIGHT/2) | MASK_12));
+ // It generates HS event every TS_HEIGHT lines
+ // this is related to TS_WIDTH set in register
+ // NUM_LINE_BYTE3 in budget-core.c. If NUM_LINE_BYTE
+ // low 16 bits are set to TS_WIDTH bytes (TS_WIDTH=2*188
+ //,then RPS_THRESH1
+ // should be set to trigger every TS_HEIGHT (512) lines.
+ //
+ saa7146_write(dev, RPS_THRESH1, (TS_HEIGHT*1) | MASK_12 );
+
+ // saa7146_write(dev, RPS_THRESH0, ((TS_HEIGHT/2)<<16) |MASK_28| (TS_HEIGHT/2) |MASK_12 );
// Enable RPS1 (rFC p33)
saa7146_write(dev, MC1, (MASK_13 | MASK_29));
+
+ if (!(budget = kmalloc (sizeof(struct budget_patch), GFP_KERNEL)))
+ return -ENOMEM;
+
+ dprintk(2, "budget: %p\n", budget);
+
+ if ((err = ttpci_budget_init (budget, dev, info, THIS_MODULE))) {
+ kfree (budget);
+ return err;
+ }
+
+
dev->ext_priv = budget;
budget->dvb_adapter->priv = budget;
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/