Re: current linus bk, error mounting root
From: Jon Smirl
Date: Wed Mar 09 2005 - 21:05:04 EST
On Wed, 9 Mar 2005 22:09:26 +0100, Jens Axboe <axboe@xxxxxxx> wrote:
> probably not worth the bother, looks like barrier problems. get the
> serial console running instead and send the full output, I'll take a
> look in the morning.
serial console boot output attached.
>
> --
> Jens Axboe
>
>
--
Jon Smirl
jonsmirl@xxxxxxxxx
Linux version 2.6.11-bk5 (jonsmirl@xxxxxxxxxxxxxxxxxx) (gcc version 3.4.2 20041017 (Red Hat 3.4.2-6.fc3)) #3 SMP Wed Mar 9 18:36:46 EST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ff74000 (usable)
BIOS-e820: 000000003ff74000 - 000000003ff76000 (ACPI NVS)
BIOS-e820: 000000003ff76000 - 000000003ff97000 (ACPI data)
BIOS-e820: 000000003ff97000 - 0000000040000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fecf0000 - 00000000fecf1000 (reserved)
BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000fe710
DMI 2.3 present.
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 40000000:bec00000)
Built 1 zonelists
Kernel command line: ro root=LABEL=/ console=ttyS0
Initializing CPU#0
CPU 0 irqstacks, hard=c03b3000 soft=c03b1000
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2793.222 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1034896k/1048016k available (1576k kernel code, 12396k reserved, 963k data, 188k init, 130512k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
per-CPU timeslice cutoff: 1462.56 usecs.
task migration cache decay timeout: 2 msecs.
Booting processor 1/1 eip 3000
CPU 1 irqstacks, hard=c03b4000 soft=c03b2000
Initializing CPU#1
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
Total of 2 processors activated (11091.96 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
checking if image is initramfs... it is
Freeing initrd memory: 318k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfba5e, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 *10 11 12 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 9 10 11 12 15)
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
Simple Boot Flag value 0x87 read from CMOS RAM was invalid
Simple Boot Flag at 0x7a set to 0x1
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1110395018.538:0): initialized
highmem bounce pool size: 64 pages
Initializing Cryptographic API
ACPI: PS/2 Keyboard Controller [KBD] at I/O 0x60, 0x64, irq 1
ACPI: PS/2 Mouse Controller [MOU] at irq 12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 6 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH5: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 169
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:DMA
hda: IC35L060AVV207-0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: DVD-RW IDE1008, ATAPI CD/DVD-ROM drive
hdd: LITE-ON LTR-52246S, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 78125000 sectors (40000 MB) w/1821KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4
hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
mice: PS/2 mouse device common for all mice
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
Starting balanced_irq
ACPI wakeup devices:
VBTN PCI0 USB0 USB1 USB2 USB3 PCI1 MOU
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 188k freed
Red Hat nash version 4.1.18 starting
Mounted /proc filesystem
md: raid1 personality registered as nr 3
Mounting sysfs
md: Autodetecting RAID arrays.
Creating /dev
SACPI: PCI interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 169
tarting udev
Lomd: autorun ...
md: considering hda2 ...
md: adding hda2 ...
md: created md0
md: bind<hda2>
md: running: <hda2>
ading libata.ko raid1: raid set md0 active with 1 out of 2 mirrors
md: ... autorun DONE.
module
Loading ata1: SATA max UDMA/133 cmd 0xFE00 ctl 0xFE12 bmdma 0xFEA0 irq 169
ata_piix.ko moduata2: SATA max UDMA/133 cmd 0xFE20 ctl 0xFE32 bmdma 0xFEA8 irq 169
le
Loading raidKernel panic - not syncing: Attempted to kill init!
1.ko module
Cre ating root devic