Re: 2.6.13-rc3-mm3

From: Michael Thonke
Date: Fri Jul 29 2005 - 17:01:44 EST

Next message: Tom Rini: "[patch 14/15] Allow KGDB to work well with loaded modules"
Previous message: Gaston, Jason D: "RE: [PATCH 2.6.13-rc4 1/1] pci_ids: patch for Intel ICH7R"
In reply to: Andrew Morton: "Re: 2.6.13-rc3-mm3"
Next in thread: Martin J. Bligh: "Re: 2.6.13-rc3-mm3"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Andrew Morton schrieb:

Michael Thonke <tk-shockwave@xxxxxx> wrote:

Andrew Morton schrieb:

Michael Thonke <iogl64nx@xxxxxxxxx> wrote:

here again I have two problems. With 2.6.13-rc3-mm3 I have problems using my SATA drives on Intel ICH6.
The kernel can't route there IRQs or can't discover them. the option irqpoll got them to work now.
The problem is new because 2.6.13-rc3[-mm1,mm2] work without any problems.

OK. Please generate the full dmesg output for -mm2 and for -mm3 and run
`diff -u dmesg.mm2 dmesg.mm3' and send it? And keep those files because we
may end up needing to add them to an acpi bugzilla entry ;)

Well I did a little mistake..it only worked correctly up to
2.6.13-rc3-mm1 but this dmesg output I have.

Well as I save mm[2,3] are unable to setup the correct IRQs for the
devices..and please note that 2.6.13-rc3-mm3 only booted with irqpoll so
its in the dmesg output "dmesg.mm3"
Normaly the IRQ routed to something about 1xx now they are 1-21?! Caused
by irqpoll?

Are these problems only present in -mm kernels? Does 2.6.13-rc4 work OK?

I'm sorry to say that, Yes.

I finially compiled a fresh 2.6.13-rc4-git1 kernel with ck-patch and Gregh-kh patches.

With this kernel non of the problems I had with mm-kernel are present.
Here is everthing just perfect..now
I attached a dmesg output for review :-)

The Oops on probing snd-hda-intel gone. It works now ... Mozart rocks :-)
I look at the CVS tree of Alsa later.

I finialy converted my reiser4 root to reiser 3.6.

Where I can get acpidumb or what it is called?

Odd trace. Do you have CONFIG_KALLSYMS enabled? If not, please turn it on.

Okay, i will do so ... what else we need to back that out.

Mh I tried but my system freezes on boot then. And screen leaves blank.

Oh geeze.

Like oh my god? ;-)

@@ -53,10 +23,18 @@
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
+ ACPI-0287: *** Error: Region SystemMemory(0) has no handler
+ ACPI-0127: *** Error: acpi_load_tables: Could not load namespace: AE_NOT_EXIST
+ ACPI-0136: *** Error: acpi_load_tables: Could not load tables: AE_NOT_EXIST
+ACPI: Unable to load the System Description Tables
ENABLING IO-APIC IRQs
-..TIMER: vector=0x31 pin1=2 pin2=0
+..TIMER: vector=0x31 pin1=2 pin2=-1

The pin2=-1 is wrong I think, right?

NET: Registered protocol family 16
PCI: Using configuration type 1
+ACPI: Subsystem revision 20050708
+ACPI: Interpreter disabled.

Well it looks like ACPI committed suicide, so there's probably not much
point looking at the other things until that gets addressed.

Would you have time to raise a kernel bugzilla entry for this? Raise it
against the ACPI AML interpreter, version 20050708 and mention the above
failure. The output of acpidump (from
ftp://ftp.kernel.org/pub/linux/kernel/people/lenb/acpi/utils/pmtools-20050727.tar.gz)
will probably be asked for.

Thanks.

Sorry for my different mail accounts, gmail have some problems.
Let me say, Thanks again for the help Andrew and all others.
IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Subsystem revision 20050408
ACPI-0362: *** Error: Looking up [CHAF] in namespace, AE_NOT_FOUND
search_node b1994240 start_node b1994240 return_node 00000000
ACPI-0362: *** Error: Looking up [OC06] in namespace, AE_NOT_FOUND
search_node b1994f60 start_node b1994f60 return_node 00000000
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:04:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 *7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Bridge: 0000:00:01.0
IO window: e000-efff
MEM window: d2f00000-d7ffffff
PREFETCH window: d8000000-dfffffff
PCI: Bridge: 0000:00:1c.0
IO window: d000-dfff
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.1
IO window: c000-cfff
MEM window: d2e00000-d2efffff
PREFETCH window: 40000000-400fffff
PCI: Bridge: 0000:00:1e.0
IO window: b000-bfff
MEM window: disabled.
PREFETCH window: disabled.
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.1 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
pnp: 00:06: ioport range 0x290-0x297 has been reserved
Machine check exception polling timer started.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
Initializing Cryptographic API
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie02]
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie02]
vesafb: framebuffer at 0xd8000000, mapped to 0xf0880000, using 5120k, total 131072k
vesafb: mode is 1280x1024x16, linelength=2560, pages=1
vesafb: protected mode interface info at c000:d620
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 160x64
fb0: VESA VGA frame buffer device
fb1: Virtual frame buffer device, using 1024K of video memory
ACPI: CPU0 (power states: C1[C1])
ACPI: Processor [CPU1] (supports 8 throttling states)
Real Time Clock Driver v1.12
i8xx TCO timer: heartbeat value must be 2<heartbeat<39, using 30
i8xx TCO timer: initialized (0x0860). heartbeat=30 sec (nowayout=0)
mice: PS/2 mouse device common for all mice
io scheduler noop registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 2 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
ub: sizeof ub_scsi_cmd 68 ub_dev 2388 ub_lun 140
usbcore: registered new driver ub
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17
sk98lin: Network Device Driver v8.23.1.3
(C)Copyright 1999-2005 Marvell(R).
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:02:00.0 to 64
eth0: Marvell Yukon 88E8053 Gigabit Ethernet Controller
PrefPort:A RlmtMode:Check Link State
netconsole: not configured, aborting
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH6: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
ICH6: chipset revision 5
ICH6: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: HL-DT-ST DVDRAM GSA-4163B, ATAPI CD/DVD-ROM drive
hdb: LITE-ON LTR-52246S, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: ATAPI 63X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdb: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
libata version 1.11 loaded.
ata_piix version 1.03
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0xAC00 ctl 0xA882 bmdma 0xA400 irq 19
ata2: SATA max UDMA/133 cmd 0xA800 ctl 0xA482 bmdma 0xA408 irq 19
ata1: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7469 86:3c01 87:4023 88:20ff
ata1: dev 0 ATA, max UDMA7, 312581808 sectors: lba48
ata1: dev 0 configured for UDMA/133
scsi0 : ata_piix
ata2: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7469 86:3c01 87:4023 88:20ff
ata2: dev 0 ATA, max UDMA7, 312581808 sectors: lba48
ata2: dev 0 configured for UDMA/133
scsi1 : ata_piix
Vendor: ATA Model: SAMSUNG HD160JJ Rev: WU10
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: SAMSUNG HD160JJ Rev: WU10
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 < sda5 sda6 sda7 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2 < sdb5 sdb6 sdb7 sdb8 >
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 0
usbmon: debugs is not available
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: irq 20, io mem 0xd2dffc00
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 20, io base 0x00009880
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 19, io base 0x00009c00
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000a000
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000a080
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usb 2-1: new low speed USB device using uhci_hcd and address 2
usb 2-2: new low speed USB device using uhci_hcd and address 3
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
input: USB HID v1.10 Keyboard [CHESEN USB Keyboard] on usb-0000:00:1d.0-1
input: USB HID v1.10 Device [CHESEN USB Keyboard] on usb-0000:00:1d.0-1
input: USB HID v1.10 Mouse [Genius NetScroll+Mini Traveler] on usb-0000:00:1d.0-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
usb 4-1: new full speed USB device using uhci_hcd and address 2
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic
usbcore: registered new driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
drivers/usb/serial/usb-serial.c: USB Serial support registered for PL-2303
pl2303 4-1:1.0: PL-2303 converter detected
usb 4-1: PL-2303 converter now attached to ttyUSB0
usbcore: registered new driver pl2303
drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver v0.12
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 3.38
Advanced Linux Sound Architecture Driver Version 1.0.9b (Thu Jul 28 12:20:13 2005 UTC).
ALSA device list:
No soundcards found.
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
ACPI wakeup devices:
P0P1 P0P3 P0P4 P0P5 P0P6 P0P7 USB1 USB2 USB3 USB4 EUSB MC97
ACPI: (supports S0 S1 S3 S4 S5)
md: Autodetecting RAID arrays.
md: autorun ...
md: considering sdb7 ...
md: adding sdb7 ...
md: sdb6 has different UUID to sdb7
md: sdb5 has different UUID to sdb7
md: sda7 has different UUID to sdb7
md: adding sda6 ...
md: sda5 has different UUID to sdb7
md: created md2
md: bind<sda6>
md: bind<sdb7>
md: running: <sdb7><sda6>
md2: setting max_sectors to 128, segment boundary to 32767
raid0: looking at sdb7
raid0: comparing sdb7(20000768) with sdb7(20000768)
raid0: END
raid0: ==> UNIQUE
raid0: 1 zones
raid0: looking at sda6
raid0: comparing sda6(20000768) with sdb7(20000768)
raid0: EQUAL
raid0: FINAL 1 zones
raid0: done.
raid0 : md_size is 40001536 blocks.
raid0 : conf->hash_spacing is 40001536 blocks.
raid0 : nb_zone is 1.
raid0 : Allocating 4 bytes for hash.
md: considering sdb6 ...
md: adding sdb6 ...
md: sdb5 has different UUID to sdb6
md: sda7 has different UUID to sdb6
md: adding sda5 ...
md: created md0
md: bind<sda5>
md: bind<sdb6>
md: running: <sdb6><sda5>
md0: setting max_sectors to 128, segment boundary to 32767
raid0: looking at sdb6
raid0: comparing sdb6(20000768) with sdb6(20000768)
raid0: END
raid0: ==> UNIQUE
raid0: 1 zones
raid0: looking at sda5
raid0: comparing sda5(20000768) with sdb6(20000768)
raid0: EQUAL
raid0: FINAL 1 zones
raid0: done.
raid0 : md_size is 40001536 blocks.
raid0 : conf->hash_spacing is 40001536 blocks.
raid0 : nb_zone is 1.
raid0 : Allocating 4 bytes for hash.
md: considering sdb5 ...
md: adding sdb5 ...
md: adding sda7 ...
md: created md1
md: bind<sda7>
md: bind<sdb5>
md: running: <sdb5><sda7>
md1: setting max_sectors to 128, segment boundary to 32767
raid0: looking at sdb5
raid0: comparing sdb5(20000768) with sdb5(20000768)
raid0: END
raid0: ==> UNIQUE
raid0: 1 zones
raid0: looking at sda7
raid0: comparing sda7(20000768) with sdb5(20000768)
raid0: EQUAL
raid0: FINAL 1 zones
raid0: done.
raid0 : md_size is 40001536 blocks.
raid0 : conf->hash_spacing is 40001536 blocks.
raid0 : nb_zone is 1.
raid0 : Allocating 4 bytes for hash.
md: ... autorun DONE.
ReiserFS: md2: found reiserfs format "3.6" with standard journal
ReiserFS: md2: using ordered data mode
ReiserFS: md2: journal params: device md2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: md2: checking transaction log (md2)
ReiserFS: md2: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 192k freed
ReiserFS: sdb1: found reiserfs format "3.6" with standard journal
ReiserFS: sdb1: using ordered data mode
ReiserFS: sdb1: journal params: device sdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sdb1: checking transaction log (sdb1)
ReiserFS: sdb1: Using r5 hash to sort names
eth0: network connection up using port A
speed: 100
autonegotiation: yes
duplex mode: full
flowctrl: symmetric
irq moderation: disabled
tcp offload: enabled
scatter-gather: enabled
tx-checksum: enabled
rx-checksum: enabled
rx-polling: enabled
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1b.0 to 64
hda_codec: Unknown model for ALC880, trying auto-probe from BIOS...
hda_codec: num_steps = 0 for NID=0x8
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:04:00.0 to 64
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-7667 Fri Jun 17 07:01:04 PDT 2005
hda_codec: num_steps = 0 for NID=0x9
hda_codec: num_steps = 0 for NID=0x9

Next message: Tom Rini: "[patch 14/15] Allow KGDB to work well with loaded modules"
Previous message: Gaston, Jason D: "RE: [PATCH 2.6.13-rc4 1/1] pci_ids: patch for Intel ICH7R"
In reply to: Andrew Morton: "Re: 2.6.13-rc3-mm3"
Next in thread: Martin J. Bligh: "Re: 2.6.13-rc3-mm3"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]