Re: [PATCH] ppc32 :Added PCI support for MPC83xx
From: Kumar Gala
Date: Mon Aug 29 2005 - 17:02:29 EST
On Aug 29, 2005, at 1:07 PM, Dan Malek wrote:
On Aug 29, 2005, at 1:42 PM, Kumar Gala wrote:
diff --git a/arch/ppc/platforms/83xx/mpc834x_sys.c
b/arch/ppc/platforms/83xx/mpc834x_sys.c
--- a/arch/ppc/platforms/83xx/mpc834x_sys.c
+++ b/arch/ppc/platforms/83xx/mpc834x_sys.c
@@ -62,9 +62,29 @@ extern unsigned long total_memory; /* in
unsigned char __res[sizeof (bd_t)];
#ifdef CONFIG_PCI
-#error "PCI is not supported"
-/* NEED mpc83xx_map_irq & mpc83xx_exclude_device
- see platforms/85xx/mpc85xx_ads_common.c */
+int
+mpc83xx_map_irq(struct pci_dev *dev, unsigned char idsel, unsigned
char pin)
+{
+ static char pci_irq_table[][4] =
+ /*
+ * PCI IDSEL/INTPIN->INTLINE
+ * A B C D
+ */
+ {
+ {PIRQA, PIRQB, PIRQC, PIRQD}, /* idsel 0x11 */
+ {PIRQC, PIRQD, PIRQA, PIRQB}, /* idsel 0x12 */
+ {PIRQD, PIRQA, PIRQB, PIRQC} /* idsel 0x13 */
+ };
+
+ const long min_idsel = 0x11, max_idsel = 0x13, irqs_per_slot =
4;
+ return PCI_IRQ_TABLE_LOOKUP;
+}
+
+int
+mpc83xx_exclude_device(u_char bus, u_char devfn)
+{
+ return PCIBIOS_SUCCESSFUL;
+}
#endif /* CONFIG_PCI */
Shouldn't this be in the PQ2FADS board specific file? Not everyone
is going to map IDSELs and IRQs this way.
mpc834x_sys is a board specific file.. This is stupid freescale
naming. The board was called MPC8349 SYS... Not sure what its called
now.
diff --git a/arch/ppc/platforms/83xx/mpc834x_sys.h
b/arch/ppc/platforms/83xx/mpc834x_sys.h
--- a/arch/ppc/platforms/83xx/mpc834x_sys.h
+++ b/arch/ppc/platforms/83xx/mpc834x_sys.h
@@ -26,7 +26,7 @@
#define VIRT_IMMRBAR ((uint)0xfe000000)
#define BCSR_PHYS_ADDR ((uint)0xf8000000)
-#define BCSR_SIZE ((uint)(32 * 1024))
+#define BCSR_SIZE ((uint)(128 * 1024))
#define BCSR_MISC_REG2_OFF 0x07
#define BCSR_MISC_REG2_PORESET 0x01
@@ -34,23 +34,25 @@
#define BCSR_MISC_REG3_OFF 0x08
#define BCSR_MISC_REG3_CNFLOCK 0x80
-#ifdef CONFIG_PCI
-/* PCI interrupt controller */
-#define PIRQA MPC83xx_IRQ_IRQ4
-#define PIRQB MPC83xx_IRQ_IRQ5
-#define PIRQC MPC83xx_IRQ_IRQ6
-#define PIRQD MPC83xx_IRQ_IRQ7
-
-#define MPC834x_SYS_PCI1_LOWER_IO 0x00000000
-#define MPC834x_SYS_PCI1_UPPER_IO 0x00ffffff
-
-#define MPC834x_SYS_PCI1_LOWER_MEM 0x80000000
-#define MPC834x_SYS_PCI1_UPPER_MEM 0x9fffffff
-
-#define MPC834x_SYS_PCI1_IO_BASE 0xe2000000
-#define MPC834x_SYS_PCI1_MEM_OFFSET 0x00000000
-
-#define MPC834x_SYS_PCI1_IO_SIZE 0x01000000
-#endif /* CONFIG_PCI */
+#define PIRQA MPC83xx_IRQ_EXT4
+#define PIRQB MPC83xx_IRQ_EXT5
+#define PIRQC MPC83xx_IRQ_EXT6
+#define PIRQD MPC83xx_IRQ_EXT7
The same thing with these BCSRs and IRQ mappings .... FADS specific.
Same comment as above.
+
+#define MPC83xx_PCI1_LOWER_IO 0x00000000
+#define MPC83xx_PCI1_UPPER_IO 0x00ffffff
+#define MPC83xx_PCI1_LOWER_MEM 0x80000000
+#define MPC83xx_PCI1_UPPER_MEM 0x9fffffff
+#define MPC83xx_PCI1_IO_BASE 0xe2000000
+#define MPC83xx_PCI1_MEM_OFFSET 0x00000000
+#define MPC83xx_PCI1_IO_SIZE 0x01000000
+
+#define MPC83xx_PCI2_LOWER_IO 0x00000000
+#define MPC83xx_PCI2_UPPER_IO 0x00ffffff
+#define MPC83xx_PCI2_LOWER_MEM 0xa0000000
+#define MPC83xx_PCI2_UPPER_MEM 0xbfffffff
+#define MPC83xx_PCI2_IO_BASE 0xe3000000
+#define MPC83xx_PCI2_MEM_OFFSET 0x00000000
+#define MPC83xx_PCI2_IO_SIZE 0x01000000
These should be generic to everyone, and could be
in the ppc83xx_pci.h file. Maybe surround them with
#ifndef so a board specific file could move the addresses
if they wanted? I don't think an #ifndef is needed for each
define, maybe just #fndef MPC83xx_PCI1_LOWER_MEM
and let the board define everything if they want anything different.
This is just like how we did 85xx. The board specific file has to
fill out these defines for its memory map. I'm guess this is all
confusion based on the name, if its not just that let me know.
- kumar
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/