[RFC: 2.6 patch] remove drivers/net/tulip/xircom_tulip_cb.c

From: Adrian Bunk
Date: Thu Nov 17 2005 - 22:33:11 EST

Next message: Adrian Bunk: "[RFC: 2.6 patch] remove drivers/net/eepro100.c"
Previous message: David Gibson: "[PATCH] Fix error handling with put_compat_statfs()"
Next in thread: Mark Lord: "Re: [RFC: 2.6 patch] remove drivers/net/tulip/xircom_tulip_cb.c"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

This patch removes the obsolete drivers/net/tulip/xircom_tulip_cb.c
driver.

Is there any reason why it should be kept?

Signed-off-by: Adrian Bunk <bunk@xxxxxxxxx>

---

drivers/net/tulip/Kconfig | 16
drivers/net/tulip/Makefile | 1
drivers/net/tulip/xircom_tulip_cb.c | 1748 ----------------------------
3 files changed, 1 insertion(+), 1764 deletions(-)

--- linux-2.6.15-rc1-mm1-full/drivers/net/tulip/Kconfig.old 2005-11-18 03:45:53.000000000 +0100
+++ linux-2.6.15-rc1-mm1-full/drivers/net/tulip/Kconfig 2005-11-18 03:46:20.000000000 +0100
@@ -148,7 +148,7 @@
be called uli526x.

config PCMCIA_XIRCOM
- tristate "Xircom CardBus support (new driver)"
+ tristate "Xircom CardBus support"
depends on NET_TULIP && CARDBUS
---help---
This driver is for the Digital "Tulip" Ethernet CardBus adapters.
@@ -160,19 +160,5 @@
<file:Documentation/networking/net-modules.txt>. The module will
be called xircom_cb. If unsure, say N.

-config PCMCIA_XIRTULIP
- tristate "Xircom Tulip-like CardBus support (old driver)"
- depends on NET_TULIP && CARDBUS && BROKEN_ON_SMP
- select CRC32
- ---help---
- This driver is for the Digital "Tulip" Ethernet CardBus adapters.
- It should work with most DEC 21*4*-based chips/ethercards, as well
- as with work-alike chips from Lite-On (PNIC) and Macronix (MXIC) and
- ASIX.
-
- To compile this driver as a module, choose M here and read
- <file:Documentation/networking/net-modules.txt>. The module will
- be called xircom_tulip_cb. If unsure, say N.
-
endmenu

--- linux-2.6.15-rc1-mm1-full/drivers/net/tulip/Makefile.old 2005-11-18 03:46:32.000000000 +0100
+++ linux-2.6.15-rc1-mm1-full/drivers/net/tulip/Makefile 2005-11-18 03:46:41.000000000 +0100
@@ -2,7 +2,6 @@
# Makefile for the Linux "Tulip" family network device drivers.
#

-obj-$(CONFIG_PCMCIA_XIRTULIP) += xircom_tulip_cb.o
obj-$(CONFIG_PCMCIA_XIRCOM) += xircom_cb.o
obj-$(CONFIG_DM9102) += dmfe.o
obj-$(CONFIG_WINBOND_840) += winbond-840.o
--- linux-2.6.15-rc1-mm1-full/drivers/net/tulip/xircom_tulip_cb.c 2005-10-28 02:02:08.000000000 +0200
+++ /dev/null 2005-11-08 19:07:57.000000000 +0100
@@ -1,1748 +0,0 @@
-/* xircom_tulip_cb.c: A Xircom CBE-100 ethernet driver for Linux. */
-/*
- Written/copyright 1994-1999 by Donald Becker.
-
- This software may be used and distributed according to the terms
- of the GNU General Public License, incorporated herein by reference.
-
- The author may be reached as becker@xxxxxxxxx, or C/O
- Scyld Computing Corporation
- 410 Severn Ave., Suite 210
- Annapolis MD 21403
-
- -----------------------------------------------------------
-
- Linux kernel-specific changes:
-
- LK1.0 (Ion Badulescu)
- - Major cleanup
- - Use 2.4 PCI API
- - Support ethtool
- - Rewrite perfect filter/hash code
- - Use interrupts for media changes
-
- LK1.1 (Ion Badulescu)
- - Disallow negotiation of unsupported full-duplex modes
-*/
-
-#define DRV_NAME "xircom_tulip_cb"
-#define DRV_VERSION "0.91+LK1.1"
-#define DRV_RELDATE "October 11, 2001"
-
-#define CARDBUS 1
-
-/* A few user-configurable values. */
-
-#define xircom_debug debug
-#ifdef XIRCOM_DEBUG
-static int xircom_debug = XIRCOM_DEBUG;
-#else
-static int xircom_debug = 1;
-#endif
-
-/* Maximum events (Rx packets, etc.) to handle at each interrupt. */
-static int max_interrupt_work = 25;
-
-#define MAX_UNITS 4
-/* Used to pass the full-duplex flag, etc. */
-static int full_duplex[MAX_UNITS];
-static int options[MAX_UNITS];
-static int mtu[MAX_UNITS]; /* Jumbo MTU for interfaces. */
-
-/* Keep the ring sizes a power of two for efficiency.
- Making the Tx ring too large decreases the effectiveness of channel
- bonding and packet priority.
- There are no ill effects from too-large receive rings. */
-#define TX_RING_SIZE 16
-#define RX_RING_SIZE 32
-
-/* Set the copy breakpoint for the copy-only-tiny-buffer Rx structure. */
-#ifdef __alpha__
-static int rx_copybreak = 1518;
-#else
-static int rx_copybreak = 100;
-#endif
-
-/*
- Set the bus performance register.
- Typical: Set 16 longword cache alignment, no burst limit.
- Cache alignment bits 15:14 Burst length 13:8
- 0000 No alignment 0x00000000 unlimited 0800 8 longwords
- 4000 8 longwords 0100 1 longword 1000 16 longwords
- 8000 16 longwords 0200 2 longwords 2000 32 longwords
- C000 32 longwords 0400 4 longwords
- Warning: many older 486 systems are broken and require setting 0x00A04800
- 8 longword cache alignment, 8 longword burst.
- ToDo: Non-Intel setting could be better.
-*/
-
-#if defined(__alpha__) || defined(__ia64__) || defined(__x86_64__)
-static int csr0 = 0x01A00000 | 0xE000;
-#elif defined(__powerpc__)
-static int csr0 = 0x01B00000 | 0x8000;
-#elif defined(__sparc__)
-static int csr0 = 0x01B00080 | 0x8000;
-#elif defined(__i386__)
-static int csr0 = 0x01A00000 | 0x8000;
-#else
-#warning Processor architecture undefined!
-static int csr0 = 0x00A00000 | 0x4800;
-#endif
-
-/* Operational parameters that usually are not changed. */
-/* Time in jiffies before concluding the transmitter is hung. */
-#define TX_TIMEOUT (4 * HZ)
-#define PKT_BUF_SZ 1536 /* Size of each temporary Rx buffer.*/
-#define PKT_SETUP_SZ 192 /* Size of the setup frame */
-
-/* PCI registers */
-#define PCI_POWERMGMT 0x40
-
-#include <linux/config.h>
-#include <linux/module.h>
-#include <linux/moduleparam.h>
-#include <linux/kernel.h>
-#include <linux/pci.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/delay.h>
-#include <linux/init.h>
-#include <linux/mii.h>
-#include <linux/ethtool.h>
-#include <linux/crc32.h>
-
-#include <asm/io.h>
-#include <asm/processor.h> /* Processor type for cache alignment. */
-#include <asm/uaccess.h>
-
-
-/* These identify the driver base version and may not be removed. */
-static char version[] __devinitdata =
-KERN_INFO DRV_NAME ".c derived from tulip.c:v0.91 4/14/99 becker@xxxxxxxxx\n"
-KERN_INFO " unofficial 2.4.x kernel port, version " DRV_VERSION ", " DRV_RELDATE "\n";
-
-MODULE_AUTHOR("Donald Becker <becker@xxxxxxxxx>");
-MODULE_DESCRIPTION("Xircom CBE-100 ethernet driver");
-MODULE_LICENSE("GPL v2");
-MODULE_VERSION(DRV_VERSION);
-
-module_param(debug, int, 0);
-module_param(max_interrupt_work, int, 0);
-module_param(rx_copybreak, int, 0);
-module_param(csr0, int, 0);
-
-module_param_array(options, int, NULL, 0);
-module_param_array(full_duplex, int, NULL, 0);
-
-#define RUN_AT(x) (jiffies + (x))
-
-/*
- Theory of Operation
-
-I. Board Compatibility
-
-This device driver was forked from the driver for the DECchip "Tulip",
-Digital's single-chip ethernet controllers for PCI. It supports Xircom's
-almost-Tulip-compatible CBE-100 CardBus adapters.
-
-II. Board-specific settings
-
-PCI bus devices are configured by the system at boot time, so no jumpers
-need to be set on the board. The system BIOS preferably should assign the
-PCI INTA signal to an otherwise unused system IRQ line.
-
-III. Driver operation
-
-IIIa. Ring buffers
-
-The Xircom can use either ring buffers or lists of Tx and Rx descriptors.
-This driver uses statically allocated rings of Rx and Tx descriptors, set at
-compile time by RX/TX_RING_SIZE. This version of the driver allocates skbuffs
-for the Rx ring buffers at open() time and passes the skb->data field to the
-Xircom as receive data buffers. When an incoming frame is less than
-RX_COPYBREAK bytes long, a fresh skbuff is allocated and the frame is
-copied to the new skbuff. When the incoming frame is larger, the skbuff is
-passed directly up the protocol stack and replaced by a newly allocated
-skbuff.
-
-The RX_COPYBREAK value is chosen to trade-off the memory wasted by
-using a full-sized skbuff for small frames vs. the copying costs of larger
-frames. For small frames the copying cost is negligible (esp. considering
-that we are pre-loading the cache with immediately useful header
-information). For large frames the copying cost is non-trivial, and the
-larger copy might flush the cache of useful data. A subtle aspect of this
-choice is that the Xircom only receives into longword aligned buffers, thus
-the IP header at offset 14 isn't longword aligned for further processing.
-Copied frames are put into the new skbuff at an offset of "+2", thus copying
-has the beneficial effect of aligning the IP header and preloading the
-cache.
-
-IIIC. Synchronization
-The driver runs as two independent, single-threaded flows of control. One
-is the send-packet routine, which enforces single-threaded use by the
-dev->tbusy flag. The other thread is the interrupt handler, which is single
-threaded by the hardware and other software.
-
-The send packet thread has partial control over the Tx ring and 'dev->tbusy'
-flag. It sets the tbusy flag whenever it's queuing a Tx packet. If the next
-queue slot is empty, it clears the tbusy flag when finished otherwise it sets
-the 'tp->tx_full' flag.
-
-The interrupt handler has exclusive control over the Rx ring and records stats
-from the Tx ring. (The Tx-done interrupt can't be selectively turned off, so
-we can't avoid the interrupt overhead by having the Tx routine reap the Tx
-stats.) After reaping the stats, it marks the queue entry as empty by setting
-the 'base' to zero. Iff the 'tp->tx_full' flag is set, it clears both the
-tx_full and tbusy flags.
-
-IV. Notes
-
-IVb. References
-
-http://cesdis.gsfc.nasa.gov/linux/misc/NWay.html
-http://www.digital.com (search for current 21*4* datasheets and "21X4 SROM")
-http://www.national.com/pf/DP/DP83840A.html
-
-IVc. Errata
-
-*/
-
-/* A full-duplex map for media types. */
-enum MediaIs {
- MediaIsFD = 1, MediaAlwaysFD=2, MediaIsMII=4, MediaIsFx=8,
- MediaIs100=16};
-static const char media_cap[] =
-{0,0,0,16, 3,19,16,24, 27,4,7,5, 0,20,23,20 };
-
-/* Offsets to the Command and Status Registers, "CSRs". All accesses
- must be longword instructions and quadword aligned. */
-enum xircom_offsets {
- CSR0=0, CSR1=0x08, CSR2=0x10, CSR3=0x18, CSR4=0x20, CSR5=0x28,
- CSR6=0x30, CSR7=0x38, CSR8=0x40, CSR9=0x48, CSR10=0x50, CSR11=0x58,
- CSR12=0x60, CSR13=0x68, CSR14=0x70, CSR15=0x78, CSR16=0x04, };
-
-/* The bits in the CSR5 status registers, mostly interrupt sources. */
-enum status_bits {
- LinkChange=0x08000000,
- NormalIntr=0x10000, NormalIntrMask=0x00014045,
- AbnormalIntr=0x8000, AbnormalIntrMask=0x0a00a5a2,
- ReservedIntrMask=0xe0001a18,
- EarlyRxIntr=0x4000, BusErrorIntr=0x2000,
- EarlyTxIntr=0x400, RxDied=0x100, RxNoBuf=0x80, RxIntr=0x40,
- TxFIFOUnderflow=0x20, TxNoBuf=0x04, TxDied=0x02, TxIntr=0x01,
-};
-
-enum csr0_control_bits {
- EnableMWI=0x01000000, EnableMRL=0x00800000,
- EnableMRM=0x00200000, EqualBusPrio=0x02,
- SoftwareReset=0x01,
-};
-
-enum csr6_control_bits {
- ReceiveAllBit=0x40000000, AllMultiBit=0x80, PromiscBit=0x40,
- HashFilterBit=0x01, FullDuplexBit=0x0200,
- TxThresh10=0x400000, TxStoreForw=0x200000,
- TxThreshMask=0xc000, TxThreshShift=14,
- EnableTx=0x2000, EnableRx=0x02,
- ReservedZeroMask=0x8d930134, ReservedOneMask=0x320c0000,
- EnableTxRx=(EnableTx | EnableRx),
-};
-
-
-enum tbl_flag {
- HAS_MII=1, HAS_ACPI=2,
-};
-static struct xircom_chip_table {
- char *chip_name;
- int valid_intrs; /* CSR7 interrupt enable settings */
- int flags;
-} xircom_tbl[] = {
- { "Xircom Cardbus Adapter",
- LinkChange | NormalIntr | AbnormalIntr | BusErrorIntr |
- RxDied | RxNoBuf | RxIntr | TxFIFOUnderflow | TxNoBuf | TxDied | TxIntr,
- HAS_MII | HAS_ACPI, },
- { NULL, },
-};
-/* This matches the table above. */
-enum chips {
- X3201_3,
-};
-
-
-/* The Xircom Rx and Tx buffer descriptors. */
-struct xircom_rx_desc {
- s32 status;
- s32 length;
- u32 buffer1, buffer2;
-};
-
-struct xircom_tx_desc {
- s32 status;
- s32 length;
- u32 buffer1, buffer2; /* We use only buffer 1. */
-};
-
-enum tx_desc0_status_bits {
- Tx0DescOwned=0x80000000, Tx0DescError=0x8000, Tx0NoCarrier=0x0800,
- Tx0LateColl=0x0200, Tx0ManyColl=0x0100, Tx0Underflow=0x02,
-};
-enum tx_desc1_status_bits {
- Tx1ComplIntr=0x80000000, Tx1LastSeg=0x40000000, Tx1FirstSeg=0x20000000,
- Tx1SetupPkt=0x08000000, Tx1DisableCRC=0x04000000, Tx1RingWrap=0x02000000,
- Tx1ChainDesc=0x01000000, Tx1NoPad=0x800000, Tx1HashSetup=0x400000,
- Tx1WholePkt=(Tx1FirstSeg | Tx1LastSeg),
-};
-enum rx_desc0_status_bits {
- Rx0DescOwned=0x80000000, Rx0DescError=0x8000, Rx0NoSpace=0x4000,
- Rx0Runt=0x0800, Rx0McastPkt=0x0400, Rx0FirstSeg=0x0200, Rx0LastSeg=0x0100,
- Rx0HugeFrame=0x80, Rx0CRCError=0x02,
- Rx0WholePkt=(Rx0FirstSeg | Rx0LastSeg),
-};
-enum rx_desc1_status_bits {
- Rx1RingWrap=0x02000000, Rx1ChainDesc=0x01000000,
-};
-
-struct xircom_private {
- struct xircom_rx_desc rx_ring[RX_RING_SIZE];
- struct xircom_tx_desc tx_ring[TX_RING_SIZE];
- /* The saved address of a sent-in-place packet/buffer, for skfree(). */
- struct sk_buff* tx_skbuff[TX_RING_SIZE];
-#ifdef CARDBUS
- /* The X3201-3 requires 4-byte aligned tx bufs */
- struct sk_buff* tx_aligned_skbuff[TX_RING_SIZE];
-#endif
- /* The addresses of receive-in-place skbuffs. */
- struct sk_buff* rx_skbuff[RX_RING_SIZE];
- u16 setup_frame[PKT_SETUP_SZ / sizeof(u16)]; /* Pseudo-Tx frame to init address table. */
- int chip_id;
- struct net_device_stats stats;
- unsigned int cur_rx, cur_tx; /* The next free ring entry */
- unsigned int dirty_rx, dirty_tx; /* The ring entries to be free()ed. */
- unsigned int tx_full:1; /* The Tx queue is full. */
- unsigned int speed100:1;
- unsigned int full_duplex:1; /* Full-duplex operation requested. */
- unsigned int autoneg:1;
- unsigned int default_port:4; /* Last dev->if_port value. */
- unsigned int open:1;
- unsigned int csr0; /* CSR0 setting. */
- unsigned int csr6; /* Current CSR6 control settings. */
- u16 to_advertise; /* NWay capabilities advertised. */
- u16 advertising[4];
- signed char phys[4], mii_cnt; /* MII device addresses. */
- int saved_if_port;
- struct pci_dev *pdev;
- spinlock_t lock;
-};
-
-static int mdio_read(struct net_device *dev, int phy_id, int location);
-static void mdio_write(struct net_device *dev, int phy_id, int location, int value);
-static void xircom_up(struct net_device *dev);
-static void xircom_down(struct net_device *dev);
-static int xircom_open(struct net_device *dev);
-static void xircom_tx_timeout(struct net_device *dev);
-static void xircom_init_ring(struct net_device *dev);
-static int xircom_start_xmit(struct sk_buff *skb, struct net_device *dev);
-static int xircom_rx(struct net_device *dev);
-static void xircom_media_change(struct net_device *dev);
-static irqreturn_t xircom_interrupt(int irq, void *dev_instance, struct pt_regs *regs);
-static int xircom_close(struct net_device *dev);
-static struct net_device_stats *xircom_get_stats(struct net_device *dev);
-static int xircom_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
-static void set_rx_mode(struct net_device *dev);
-static void check_duplex(struct net_device *dev);
-static struct ethtool_ops ops;
-
-
-/* The Xircom cards are picky about when certain bits in CSR6 can be
- manipulated. Keith Owens <kaos@xxxxxxxxxx>. */
-static void outl_CSR6(u32 newcsr6, long ioaddr)
-{
- const int strict_bits =
- TxThresh10 | TxStoreForw | TxThreshMask | EnableTxRx | FullDuplexBit;
- int csr5, csr5_22_20, csr5_19_17, currcsr6, attempts = 200;
- unsigned long flags;
- save_flags(flags);
- cli();
- /* mask out the reserved bits that always read 0 on the Xircom cards */
- newcsr6 &= ~ReservedZeroMask;
- /* or in the reserved bits that always read 1 */
- newcsr6 |= ReservedOneMask;
- currcsr6 = inl(ioaddr + CSR6);
- if (((newcsr6 & strict_bits) == (currcsr6 & strict_bits)) ||
- ((currcsr6 & ~EnableTxRx) == 0)) {
- outl(newcsr6, ioaddr + CSR6); /* safe */
- restore_flags(flags);
- return;
- }
- /* make sure the transmitter and receiver are stopped first */
- currcsr6 &= ~EnableTxRx;
- while (1) {
- csr5 = inl(ioaddr + CSR5);
- if (csr5 == 0xffffffff)
- break; /* cannot read csr5, card removed? */
- csr5_22_20 = csr5 & 0x700000;
- csr5_19_17 = csr5 & 0x0e0000;
- if ((csr5_22_20 == 0 || csr5_22_20 == 0x600000) &&
- (csr5_19_17 == 0 || csr5_19_17 == 0x80000 || csr5_19_17 == 0xc0000))
- break; /* both are stopped or suspended */
- if (!--attempts) {
- printk(KERN_INFO DRV_NAME ": outl_CSR6 too many attempts,"
- "csr5=0x%08x\n", csr5);
- outl(newcsr6, ioaddr + CSR6); /* unsafe but do it anyway */
- restore_flags(flags);
- return;
- }
- outl(currcsr6, ioaddr + CSR6);
- udelay(1);
- }
- /* now it is safe to change csr6 */
- outl(newcsr6, ioaddr + CSR6);
- restore_flags(flags);
-}
-
-
-static void __devinit read_mac_address(struct net_device *dev)
-{
- long ioaddr = dev->base_addr;
- int i, j;
- unsigned char tuple, link, data_id, data_count;
-
- /* Xircom has its address stored in the CIS;
- * we access it through the boot rom interface for now
- * this might not work, as the CIS is not parsed but I
- * (danilo) use the offset I found on my card's CIS !!!
- *
- * Doug Ledford: I changed this routine around so that it
- * walks the CIS memory space, parsing the config items, and
- * finds the proper lan_node_id tuple and uses the data
- * stored there.
- */
- outl(1 << 12, ioaddr + CSR9); /* enable boot rom access */
- for (i = 0x100; i < 0x1f7; i += link+2) {
- outl(i, ioaddr + CSR10);
- tuple = inl(ioaddr + CSR9) & 0xff;
- outl(i + 1, ioaddr + CSR10);
- link = inl(ioaddr + CSR9) & 0xff;
- outl(i + 2, ioaddr + CSR10);
- data_id = inl(ioaddr + CSR9) & 0xff;
- outl(i + 3, ioaddr + CSR10);
- data_count = inl(ioaddr + CSR9) & 0xff;
- if ( (tuple == 0x22) &&
- (data_id == 0x04) && (data_count == 0x06) ) {
- /*
- * This is it. We have the data we want.
- */
- for (j = 0; j < 6; j++) {
- outl(i + j + 4, ioaddr + CSR10);
- dev->dev_addr[j] = inl(ioaddr + CSR9) & 0xff;
- }
- break;
- } else if (link == 0) {
- break;
- }
- }
-}
-
-
-/*
- * locate the MII interfaces and initialize them.
- * we disable full-duplex modes here,
- * because we don't know how to handle them.
- */
-static void find_mii_transceivers(struct net_device *dev)
-{
- struct xircom_private *tp = netdev_priv(dev);
- int phy, phy_idx;
-
- if (media_cap[tp->default_port] & MediaIsMII) {
- u16 media2advert[] = { 0x20, 0x40, 0x03e0, 0x60, 0x80, 0x100, 0x200 };
- tp->to_advertise = media2advert[tp->default_port - 9];
- } else
- tp->to_advertise =
- /*ADVERTISE_100BASE4 | ADVERTISE_100FULL |*/ ADVERTISE_100HALF |
- /*ADVERTISE_10FULL |*/ ADVERTISE_10HALF | ADVERTISE_CSMA;
-
- /* Find the connected MII xcvrs.
- Doing this in open() would allow detecting external xcvrs later,
- but takes much time. */
- for (phy = 0, phy_idx = 0; phy < 32 && phy_idx < sizeof(tp->phys); phy++) {
- int mii_status = mdio_read(dev, phy, MII_BMSR);
- if ((mii_status & (BMSR_100BASE4 | BMSR_100HALF | BMSR_10HALF)) == BMSR_100BASE4 ||
- ((mii_status & BMSR_100BASE4) == 0 &&
- (mii_status & (BMSR_100FULL | BMSR_100HALF | BMSR_10FULL | BMSR_10HALF)) != 0)) {
- int mii_reg0 = mdio_read(dev, phy, MII_BMCR);
- int mii_advert = mdio_read(dev, phy, MII_ADVERTISE);
- int reg4 = ((mii_status >> 6) & tp->to_advertise) | ADVERTISE_CSMA;
- tp->phys[phy_idx] = phy;
- tp->advertising[phy_idx++] = reg4;
- printk(KERN_INFO "%s: MII transceiver #%d "
- "config %4.4x status %4.4x advertising %4.4x.\n",
- dev->name, phy, mii_reg0, mii_status, mii_advert);
- }
- }
- tp->mii_cnt = phy_idx;
- if (phy_idx == 0) {
- printk(KERN_INFO "%s: ***WARNING***: No MII transceiver found!\n",
- dev->name);
- tp->phys[0] = 0;
- }
-}
-
-
-/*
- * To quote Arjan van de Ven:
- * transceiver_voodoo() enables the external UTP plug thingy.
- * it's called voodoo as I stole this code and cannot cross-reference
- * it with the specification.
- * Actually it seems to go like this:
- * - GPIO2 enables the MII itself so we can talk to it. The MII gets reset
- * so any prior MII settings are lost.
- * - GPIO0 enables the TP port so the MII can talk to the network.
- * - a software reset will reset both GPIO pins.
- * I also moved the software reset here, because doing it in xircom_up()
- * required enabling the GPIO pins each time, which reset the MII each time.
- * Thus we couldn't control the MII -- which sucks because we don't know
- * how to handle full-duplex modes so we *must* disable them.
- */
-static void transceiver_voodoo(struct net_device *dev)
-{
- struct xircom_private *tp = netdev_priv(dev);
- long ioaddr = dev->base_addr;
-
- /* Reset the chip, holding bit 0 set at least 50 PCI cycles. */
- outl(SoftwareReset, ioaddr + CSR0);
- udelay(2);
-
- /* Deassert reset. */
- outl(tp->csr0, ioaddr + CSR0);
-
- /* Reset the xcvr interface and turn on heartbeat. */
- outl(0x0008, ioaddr + CSR15);
- udelay(5); /* The delays are Xircom-recommended to give the
- * chipset time to reset the actual hardware
- * on the PCMCIA card
- */
- outl(0xa8050000, ioaddr + CSR15);
- udelay(5);
- outl(0xa00f0000, ioaddr + CSR15);
- udelay(5);
-
- outl_CSR6(0, ioaddr);
- //outl_CSR6(FullDuplexBit, ioaddr);
-}
-
-
-static int __devinit xircom_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
-{
- struct net_device *dev;
- struct xircom_private *tp;
- static int board_idx = -1;
- int chip_idx = id->driver_data;
- long ioaddr;
- int i;
- u8 chip_rev;
-
-/* when built into the kernel, we only print version if device is found */
-#ifndef MODULE
- static int printed_version;
- if (!printed_version++)
- printk(version);
-#endif
-
- //printk(KERN_INFO "xircom_init_one(%s)\n", pci_name(pdev));
-
- board_idx++;
-
- if (pci_enable_device(pdev))
- return -ENODEV;
-
- pci_set_master(pdev);
-
- ioaddr = pci_resource_start(pdev, 0);
- dev = alloc_etherdev(sizeof(*tp));
- if (!dev) {
- printk (KERN_ERR DRV_NAME "%d: cannot alloc etherdev, aborting\n", board_idx);
- return -ENOMEM;
- }
- SET_MODULE_OWNER(dev);
- SET_NETDEV_DEV(dev, &pdev->dev);
-
- dev->base_addr = ioaddr;
- dev->irq = pdev->irq;
-
- if (pci_request_regions(pdev, dev->name)) {
- printk (KERN_ERR DRV_NAME " %d: cannot reserve PCI resources, aborting\n", board_idx);
- goto err_out_free_netdev;
- }
-
- /* Bring the chip out of sleep mode.
- Caution: Snooze mode does not work with some boards! */
- if (xircom_tbl[chip_idx].flags & HAS_ACPI)
- pci_write_config_dword(pdev, PCI_POWERMGMT, 0);
-
- /* Stop the chip's Tx and Rx processes. */
- outl_CSR6(inl(ioaddr + CSR6) & ~EnableTxRx, ioaddr);
- /* Clear the missed-packet counter. */
- (volatile int)inl(ioaddr + CSR8);
-
- tp = netdev_priv(dev);
-
- spin_lock_init(&tp->lock);
- tp->pdev = pdev;
- tp->chip_id = chip_idx;
- /* BugFixes: The 21143-TD hangs with PCI Write-and-Invalidate cycles. */
- /* XXX: is this necessary for Xircom? */
- tp->csr0 = csr0 & ~EnableMWI;
-
- pci_set_drvdata(pdev, dev);
-
- /* The lower four bits are the media type. */
- if (board_idx >= 0 && board_idx < MAX_UNITS) {
- tp->default_port = options[board_idx] & 15;
- if ((options[board_idx] & 0x90) || full_duplex[board_idx] > 0)
- tp->full_duplex = 1;
- if (mtu[board_idx] > 0)
- dev->mtu = mtu[board_idx];
- }
- if (dev->mem_start)
- tp->default_port = dev->mem_start;
- if (tp->default_port) {
- if (media_cap[tp->default_port] & MediaAlwaysFD)
- tp->full_duplex = 1;
- }
- if (tp->full_duplex)
- tp->autoneg = 0;
- else
- tp->autoneg = 1;
- tp->speed100 = 1;
-
- /* The Xircom-specific entries in the device structure. */
- dev->open = &xircom_open;
- dev->hard_start_xmit = &xircom_start_xmit;
- dev->stop = &xircom_close;
- dev->get_stats = &xircom_get_stats;
- dev->do_ioctl = &xircom_ioctl;
-#ifdef HAVE_MULTICAST
- dev->set_multicast_list = &set_rx_mode;
-#endif
- dev->tx_timeout = xircom_tx_timeout;
- dev->watchdog_timeo = TX_TIMEOUT;
- SET_ETHTOOL_OPS(dev, &ops);
-
- transceiver_voodoo(dev);
-
- read_mac_address(dev);
-
- if (register_netdev(dev))
- goto err_out_cleardev;
-
- pci_read_config_byte(pdev, PCI_REVISION_ID, &chip_rev);
- printk(KERN_INFO "%s: %s rev %d at %#3lx,",
- dev->name, xircom_tbl[chip_idx].chip_name, chip_rev, ioaddr);
- for (i = 0; i < 6; i++)
- printk("%c%2.2X", i ? ':' : ' ', dev->dev_addr[i]);
- printk(", IRQ %d.\n", dev->irq);
-
- if (xircom_tbl[chip_idx].flags & HAS_MII) {
- find_mii_transceivers(dev);
- check_duplex(dev);
- }
-
- return 0;
-
-err_out_cleardev:
- pci_set_drvdata(pdev, NULL);
- pci_release_regions(pdev);
-err_out_free_netdev:
- free_netdev(dev);
- return -ENODEV;
-}
-
-
-/* MII transceiver control section.
- Read and write the MII registers using software-generated serial
- MDIO protocol. See the MII specifications or DP83840A data sheet
- for details. */
-
-/* The maximum data clock rate is 2.5 Mhz. The minimum timing is usually
- met by back-to-back PCI I/O cycles, but we insert a delay to avoid
- "overclocking" issues or future 66Mhz PCI. */
-#define mdio_delay() inl(mdio_addr)
-
-/* Read and write the MII registers using software-generated serial
- MDIO protocol. It is just different enough from the EEPROM protocol
- to not share code. The maxium data clock rate is 2.5 Mhz. */
-#define MDIO_SHIFT_CLK 0x10000
-#define MDIO_DATA_WRITE0 0x00000
-#define MDIO_DATA_WRITE1 0x20000
-#define MDIO_ENB 0x00000 /* Ignore the 0x02000 databook setting. */
-#define MDIO_ENB_IN 0x40000
-#define MDIO_DATA_READ 0x80000
-
-static int mdio_read(struct net_device *dev, int phy_id, int location)
-{
- int i;
- int read_cmd = (0xf6 << 10) | (phy_id << 5) | location;
- int retval = 0;
- long ioaddr = dev->base_addr;
- long mdio_addr = ioaddr + CSR9;
-
- /* Establish sync by sending at least 32 logic ones. */
- for (i = 32; i >= 0; i--) {
- outl(MDIO_ENB | MDIO_DATA_WRITE1, mdio_addr);
- mdio_delay();
- outl(MDIO_ENB | MDIO_DATA_WRITE1 | MDIO_SHIFT_CLK, mdio_addr);
- mdio_delay();
- }
- /* Shift the read command bits out. */
- for (i = 15; i >= 0; i--) {
- int dataval = (read_cmd & (1 << i)) ? MDIO_DATA_WRITE1 : 0;
-
- outl(MDIO_ENB | dataval, mdio_addr);
- mdio_delay();
- outl(MDIO_ENB | dataval | MDIO_SHIFT_CLK, mdio_addr);
- mdio_delay();
- }
- /* Read the two transition, 16 data, and wire-idle bits. */
- for (i = 19; i > 0; i--) {
- outl(MDIO_ENB_IN, mdio_addr);
- mdio_delay();
- retval = (retval << 1) | ((inl(mdio_addr) & MDIO_DATA_READ) ? 1 : 0);
- outl(MDIO_ENB_IN | MDIO_SHIFT_CLK, mdio_addr);
- mdio_delay();
- }
- return (retval>>1) & 0xffff;
-}
-
-
-static void mdio_write(struct net_device *dev, int phy_id, int location, int value)
-{
- int i;
- int cmd = (0x5002 << 16) | (phy_id << 23) | (location << 18) | value;
- long ioaddr = dev->base_addr;
- long mdio_addr = ioaddr + CSR9;
-
- /* Establish sync by sending 32 logic ones. */
- for (i = 32; i >= 0; i--) {
- outl(MDIO_ENB | MDIO_DATA_WRITE1, mdio_addr);
- mdio_delay();
- outl(MDIO_ENB | MDIO_DATA_WRITE1 | MDIO_SHIFT_CLK, mdio_addr);
- mdio_delay();
- }
- /* Shift the command bits out. */
- for (i = 31; i >= 0; i--) {
- int dataval = (cmd & (1 << i)) ? MDIO_DATA_WRITE1 : 0;
- outl(MDIO_ENB | dataval, mdio_addr);
- mdio_delay();
- outl(MDIO_ENB | dataval | MDIO_SHIFT_CLK, mdio_addr);
- mdio_delay();
- }
- /* Clear out extra bits. */
- for (i = 2; i > 0; i--) {
- outl(MDIO_ENB_IN, mdio_addr);
- mdio_delay();
- outl(MDIO_ENB_IN | MDIO_SHIFT_CLK, mdio_addr);
- mdio_delay();
- }
- return;
-}
-
-
-static void
-xircom_up(struct net_device *dev)
-{
- struct xircom_private *tp = netdev_priv(dev);
- long ioaddr = dev->base_addr;
- int i;
-
- xircom_init_ring(dev);
- /* Clear the tx ring */
- for (i = 0; i < TX_RING_SIZE; i++) {
- tp->tx_skbuff[i] = NULL;
- tp->tx_ring[i].status = 0;
- }
-
- if (xircom_debug > 1)
- printk(KERN_DEBUG "%s: xircom_up() irq %d.\n", dev->name, dev->irq);
-
- outl(virt_to_bus(tp->rx_ring), ioaddr + CSR3);
- outl(virt_to_bus(tp->tx_ring), ioaddr + CSR4);
-
- tp->saved_if_port = dev->if_port;
- if (dev->if_port == 0)
- dev->if_port = tp->default_port;
-
- tp->csr6 = TxThresh10 /*| FullDuplexBit*/; /* XXX: why 10 and not 100? */
-
- set_rx_mode(dev);
-
- /* Start the chip's Tx to process setup frame. */
- outl_CSR6(tp->csr6, ioaddr);
- outl_CSR6(tp->csr6 | EnableTx, ioaddr);
-
- /* Acknowledge all outstanding interrupts sources */
- outl(xircom_tbl[tp->chip_id].valid_intrs, ioaddr + CSR5);
- /* Enable interrupts by setting the interrupt mask. */
- outl(xircom_tbl[tp->chip_id].valid_intrs, ioaddr + CSR7);
- /* Enable Rx */
- outl_CSR6(tp->csr6 | EnableTxRx, ioaddr);
- /* Rx poll demand */
- outl(0, ioaddr + CSR2);
-
- /* Tell the net layer we're ready */
- netif_start_queue (dev);
-
- /* Check current media state */
- xircom_media_change(dev);
-
- if (xircom_debug > 2) {
- printk(KERN_DEBUG "%s: Done xircom_up(), CSR0 %8.8x, CSR5 %8.8x CSR6 %8.8x.\n",
- dev->name, inl(ioaddr + CSR0), inl(ioaddr + CSR5),
- inl(ioaddr + CSR6));
- }
-}
-
-
-static int
-xircom_open(struct net_device *dev)
-{
- struct xircom_private *tp = netdev_priv(dev);
-
- if (request_irq(dev->irq, &xircom_interrupt, SA_SHIRQ, dev->name, dev))
- return -EAGAIN;
-
- xircom_up(dev);
- tp->open = 1;
-
- return 0;
-}
-
-
-static void xircom_tx_timeout(struct net_device *dev)
-{
- struct xircom_private *tp = netdev_priv(dev);
- long ioaddr = dev->base_addr;
-
- if (media_cap[dev->if_port] & MediaIsMII) {
- /* Do nothing -- the media monitor should handle this. */
- if (xircom_debug > 1)
- printk(KERN_WARNING "%s: Transmit timeout using MII device.\n",
- dev->name);
- }
-
-#if defined(way_too_many_messages)
- if (xircom_debug > 3) {
- int i;
- for (i = 0; i < RX_RING_SIZE; i++) {
- u8 *buf = (u8 *)(tp->rx_ring[i].buffer1);
- int j;
- printk(KERN_DEBUG "%2d: %8.8x %8.8x %8.8x %8.8x "
- "%2.2x %2.2x %2.2x.\n",
- i, (unsigned int)tp->rx_ring[i].status,
- (unsigned int)tp->rx_ring[i].length,
- (unsigned int)tp->rx_ring[i].buffer1,
- (unsigned int)tp->rx_ring[i].buffer2,
- buf[0], buf[1], buf[2]);
- for (j = 0; buf[j] != 0xee && j < 1600; j++)
- if (j < 100) printk(" %2.2x", buf[j]);
- printk(" j=%d.\n", j);
- }
- printk(KERN_DEBUG " Rx ring %8.8x: ", (int)tp->rx_ring);
- for (i = 0; i < RX_RING_SIZE; i++)
- printk(" %8.8x", (unsigned int)tp->rx_ring[i].status);
- printk("\n" KERN_DEBUG " Tx ring %8.8x: ", (int)tp->tx_ring);
- for (i = 0; i < TX_RING_SIZE; i++)
- printk(" %8.8x", (unsigned int)tp->tx_ring[i].status);
- printk("\n");
- }
-#endif
-
- /* Stop and restart the chip's Tx/Rx processes . */
- outl_CSR6(tp->csr6 | EnableRx, ioaddr);
- outl_CSR6(tp->csr6 | EnableTxRx, ioaddr);
- /* Trigger an immediate transmit demand. */
- outl(0, ioaddr + CSR1);
-
- dev->trans_start = jiffies;
- netif_wake_queue (dev);
- tp->stats.tx_errors++;
-}
-
-
-/* Initialize the Rx and Tx rings, along with various 'dev' bits. */
-static void xircom_init_ring(struct net_device *dev)
-{
- struct xircom_private *tp = netdev_priv(dev);
- int i;
-
- tp->tx_full = 0;
- tp->cur_rx = tp->cur_tx = 0;
- tp->dirty_rx = tp->dirty_tx = 0;
-
- for (i = 0; i < RX_RING_SIZE; i++) {
- tp->rx_ring[i].status = 0;
- tp->rx_ring[i].length = PKT_BUF_SZ;
- tp->rx_ring[i].buffer2 = virt_to_bus(&tp->rx_ring[i+1]);
- tp->rx_skbuff[i] = NULL;
- }
- /* Mark the last entry as wrapping the ring. */
- tp->rx_ring[i-1].length = PKT_BUF_SZ | Rx1RingWrap;
- tp->rx_ring[i-1].buffer2 = virt_to_bus(&tp->rx_ring[0]);
-
- for (i = 0; i < RX_RING_SIZE; i++) {
- /* Note the receive buffer must be longword aligned.
- dev_alloc_skb() provides 16 byte alignment. But do *not*
- use skb_reserve() to align the IP header! */
- struct sk_buff *skb = dev_alloc_skb(PKT_BUF_SZ);
- tp->rx_skbuff[i] = skb;
- if (skb == NULL)
- break;
- skb->dev = dev; /* Mark as being used by this device. */
- tp->rx_ring[i].status = Rx0DescOwned; /* Owned by Xircom chip */
- tp->rx_ring[i].buffer1 = virt_to_bus(skb->data);
- }
- tp->dirty_rx = (unsigned int)(i - RX_RING_SIZE);
-
- /* The Tx buffer descriptor is filled in as needed, but we
- do need to clear the ownership bit. */
- for (i = 0; i < TX_RING_SIZE; i++) {
- tp->tx_skbuff[i] = NULL;
- tp->tx_ring[i].status = 0;
- tp->tx_ring[i].buffer2 = virt_to_bus(&tp->tx_ring[i+1]);
-#ifdef CARDBUS
- if (tp->chip_id == X3201_3)
- tp->tx_aligned_skbuff[i] = dev_alloc_skb(PKT_BUF_SZ);
-#endif /* CARDBUS */
- }
- tp->tx_ring[i-1].buffer2 = virt_to_bus(&tp->tx_ring[0]);
-}
-
-
-static int
-xircom_start_xmit(struct sk_buff *skb, struct net_device *dev)
-{
- struct xircom_private *tp = netdev_priv(dev);
- int entry;
- u32 flag;
-
- /* Caution: the write order is important here, set the base address
- with the "ownership" bits last. */
-
- /* Calculate the next Tx descriptor entry. */
- entry = tp->cur_tx % TX_RING_SIZE;
-
- tp->tx_skbuff[entry] = skb;
-#ifdef CARDBUS
- if (tp->chip_id == X3201_3) {
- memcpy(tp->tx_aligned_skbuff[entry]->data,skb->data,skb->len);
- tp->tx_ring[entry].buffer1 = virt_to_bus(tp->tx_aligned_skbuff[entry]->data);
- } else
-#endif
- tp->tx_ring[entry].buffer1 = virt_to_bus(skb->data);
-
- if (tp->cur_tx - tp->dirty_tx < TX_RING_SIZE/2) {/* Typical path */
- flag = Tx1WholePkt; /* No interrupt */
- } else if (tp->cur_tx - tp->dirty_tx == TX_RING_SIZE/2) {
- flag = Tx1WholePkt | Tx1ComplIntr; /* Tx-done intr. */
- } else if (tp->cur_tx - tp->dirty_tx < TX_RING_SIZE - 2) {
- flag = Tx1WholePkt; /* No Tx-done intr. */
- } else {
- /* Leave room for set_rx_mode() to fill entries. */
- flag = Tx1WholePkt | Tx1ComplIntr; /* Tx-done intr. */
- tp->tx_full = 1;
- }
- if (entry == TX_RING_SIZE - 1)
- flag |= Tx1WholePkt | Tx1ComplIntr | Tx1RingWrap;
-
- tp->tx_ring[entry].length = skb->len | flag;
- tp->tx_ring[entry].status = Tx0DescOwned; /* Pass ownership to the chip. */
- tp->cur_tx++;
- if (tp->tx_full)
- netif_stop_queue (dev);
- else
- netif_wake_queue (dev);
-
- /* Trigger an immediate transmit demand. */
- outl(0, dev->base_addr + CSR1);
-
- dev->trans_start = jiffies;
-
- return 0;
-}
-
-
-static void xircom_media_change(struct net_device *dev)
-{
- struct xircom_private *tp = netdev_priv(dev);
- long ioaddr = dev->base_addr;
- u16 reg0, reg1, reg4, reg5;
- u32 csr6 = inl(ioaddr + CSR6), newcsr6;
-
- /* reset status first */
- mdio_read(dev, tp->phys[0], MII_BMCR);
- mdio_read(dev, tp->phys[0], MII_BMSR);
-
- reg0 = mdio_read(dev, tp->phys[0], MII_BMCR);
- reg1 = mdio_read(dev, tp->phys[0], MII_BMSR);
-
- if (reg1 & BMSR_LSTATUS) {
- /* link is up */
- if (reg0 & BMCR_ANENABLE) {
- /* autonegotiation is enabled */
- reg4 = mdio_read(dev, tp->phys[0], MII_ADVERTISE);
- reg5 = mdio_read(dev, tp->phys[0], MII_LPA);
- if (reg4 & ADVERTISE_100FULL && reg5 & LPA_100FULL) {
- tp->speed100 = 1;
- tp->full_duplex = 1;
- } else if (reg4 & ADVERTISE_100HALF && reg5 & LPA_100HALF) {
- tp->speed100 = 1;
- tp->full_duplex = 0;
- } else if (reg4 & ADVERTISE_10FULL && reg5 & LPA_10FULL) {
- tp->speed100 = 0;
- tp->full_duplex = 1;
- } else {
- tp->speed100 = 0;
- tp->full_duplex = 0;
- }
- } else {
- /* autonegotiation is disabled */
- if (reg0 & BMCR_SPEED100)
- tp->speed100 = 1;
- else
- tp->speed100 = 0;
- if (reg0 & BMCR_FULLDPLX)
- tp->full_duplex = 1;
- else
- tp->full_duplex = 0;
- }
- printk(KERN_DEBUG "%s: Link is up, running at %sMbit %s-duplex\n",
- dev->name,
- tp->speed100 ? "100" : "10",
- tp->full_duplex ? "full" : "half");
- netif_carrier_on(dev);
- newcsr6 = csr6 & ~FullDuplexBit;
- if (tp->full_duplex)
- newcsr6 |= FullDuplexBit;
- if (newcsr6 != csr6)
- outl_CSR6(newcsr6, ioaddr + CSR6);
- } else {
- printk(KERN_DEBUG "%s: Link is down\n", dev->name);
- netif_carrier_off(dev);
- }
-}
-
-
-static void check_duplex(struct net_device *dev)
-{
- struct xircom_private *tp = netdev_priv(dev);
- u16 reg0;
-
- mdio_write(dev, tp->phys[0], MII_BMCR, BMCR_RESET);
- udelay(500);
- while (mdio_read(dev, tp->phys[0], MII_BMCR) & BMCR_RESET);
-
- reg0 = mdio_read(dev, tp->phys[0], MII_BMCR);
- mdio_write(dev, tp->phys[0], MII_ADVERTISE, tp->advertising[0]);
-
- if (tp->autoneg) {
- reg0 &= ~(BMCR_SPEED100 | BMCR_FULLDPLX);
- reg0 |= BMCR_ANENABLE | BMCR_ANRESTART;
- } else {
- reg0 &= ~(BMCR_ANENABLE | BMCR_ANRESTART);
- if (tp->speed100)
- reg0 |= BMCR_SPEED100;
- if (tp->full_duplex)
- reg0 |= BMCR_FULLDPLX;
- printk(KERN_DEBUG "%s: Link forced to %sMbit %s-duplex\n",
- dev->name,
- tp->speed100 ? "100" : "10",
- tp->full_duplex ? "full" : "half");
- }
- mdio_write(dev, tp->phys[0], MII_BMCR, reg0);
-}
-
-
-/* The interrupt handler does all of the Rx thread work and cleans up
- after the Tx thread. */
-static irqreturn_t xircom_interrupt(int irq, void *dev_instance, struct pt_regs *regs)
-{
- struct net_device *dev = dev_instance;
- struct xircom_private *tp = netdev_priv(dev);
- long ioaddr = dev->base_addr;
- int csr5, work_budget = max_interrupt_work;
- int handled = 0;
-
- spin_lock (&tp->lock);
-
- do {
- csr5 = inl(ioaddr + CSR5);
- /* Acknowledge all of the current interrupt sources ASAP. */
- outl(csr5 & 0x0001ffff, ioaddr + CSR5);
-
- if (xircom_debug > 4)
- printk(KERN_DEBUG "%s: interrupt csr5=%#8.8x new csr5=%#8.8x.\n",
- dev->name, csr5, inl(dev->base_addr + CSR5));
-
- if (csr5 == 0xffffffff)
- break; /* all bits set, assume PCMCIA card removed */
-
- if ((csr5 & (NormalIntr|AbnormalIntr)) == 0)
- break;
-
- handled = 1;
-
- if (csr5 & (RxIntr | RxNoBuf))
- work_budget -= xircom_rx(dev);
-
- if (csr5 & (TxNoBuf | TxDied | TxIntr)) {
- unsigned int dirty_tx;
-
- for (dirty_tx = tp->dirty_tx; tp->cur_tx - dirty_tx > 0;
- dirty_tx++) {
- int entry = dirty_tx % TX_RING_SIZE;
- int status = tp->tx_ring[entry].status;
-
- if (status < 0)
- break; /* It still hasn't been Txed */
- /* Check for Rx filter setup frames. */
- if (tp->tx_skbuff[entry] == NULL)
- continue;
-
- if (status & Tx0DescError) {
- /* There was an major error, log it. */
-#ifndef final_version
- if (xircom_debug > 1)
- printk(KERN_DEBUG "%s: Transmit error, Tx status %8.8x.\n",
- dev->name, status);
-#endif
- tp->stats.tx_errors++;
- if (status & Tx0ManyColl) {
- tp->stats.tx_aborted_errors++;
- }
- if (status & Tx0NoCarrier) tp->stats.tx_carrier_errors++;
- if (status & Tx0LateColl) tp->stats.tx_window_errors++;
- if (status & Tx0Underflow) tp->stats.tx_fifo_errors++;
- } else {
- tp->stats.tx_bytes += tp->tx_ring[entry].length & 0x7ff;
- tp->stats.collisions += (status >> 3) & 15;
- tp->stats.tx_packets++;
- }
-
- /* Free the original skb. */
- dev_kfree_skb_irq(tp->tx_skbuff[entry]);
- tp->tx_skbuff[entry] = NULL;
- }
-
-#ifndef final_version
- if (tp->cur_tx - dirty_tx > TX_RING_SIZE) {
- printk(KERN_ERR "%s: Out-of-sync dirty pointer, %d vs. %d, full=%d.\n",
- dev->name, dirty_tx, tp->cur_tx, tp->tx_full);
- dirty_tx += TX_RING_SIZE;
- }
-#endif
-
- if (tp->tx_full &&
- tp->cur_tx - dirty_tx < TX_RING_SIZE - 2)
- /* The ring is no longer full */
- tp->tx_full = 0;
-
- if (tp->tx_full)
- netif_stop_queue (dev);
- else
- netif_wake_queue (dev);
-
- tp->dirty_tx = dirty_tx;
- if (csr5 & TxDied) {
- if (xircom_debug > 2)
- printk(KERN_WARNING "%s: The transmitter stopped."
- " CSR5 is %x, CSR6 %x, new CSR6 %x.\n",
- dev->name, csr5, inl(ioaddr + CSR6), tp->csr6);
- outl_CSR6(tp->csr6 | EnableRx, ioaddr);
- outl_CSR6(tp->csr6 | EnableTxRx, ioaddr);
- }
- }
-
- /* Log errors. */
- if (csr5 & AbnormalIntr) { /* Abnormal error summary bit. */
- if (csr5 & LinkChange)
- xircom_media_change(dev);
- if (csr5 & TxFIFOUnderflow) {
- if ((tp->csr6 & TxThreshMask) != TxThreshMask)
- tp->csr6 += (1 << TxThreshShift); /* Bump up the Tx threshold */
- else
- tp->csr6 |= TxStoreForw; /* Store-n-forward. */
- /* Restart the transmit process. */
- outl_CSR6(tp->csr6 | EnableRx, ioaddr);
- outl_CSR6(tp->csr6 | EnableTxRx, ioaddr);
- }
- if (csr5 & RxDied) { /* Missed a Rx frame. */
- tp->stats.rx_errors++;
- tp->stats.rx_missed_errors += inl(ioaddr + CSR8) & 0xffff;
- outl_CSR6(tp->csr6 | EnableTxRx, ioaddr);
- }
- /* Clear all error sources, included undocumented ones! */
- outl(0x0800f7ba, ioaddr + CSR5);
- }
- if (--work_budget < 0) {
- if (xircom_debug > 1)
- printk(KERN_WARNING "%s: Too much work during an interrupt, "
- "csr5=0x%8.8x.\n", dev->name, csr5);
- /* Acknowledge all interrupt sources. */
- outl(0x8001ffff, ioaddr + CSR5);
- break;
- }
- } while (1);
-
- if (xircom_debug > 3)
- printk(KERN_DEBUG "%s: exiting interrupt, csr5=%#4.4x.\n",
- dev->name, inl(ioaddr + CSR5));
-
- spin_unlock (&tp->lock);
- return IRQ_RETVAL(handled);
-}
-
-
-static int
-xircom_rx(struct net_device *dev)
-{
- struct xircom_private *tp = netdev_priv(dev);
- int entry = tp->cur_rx % RX_RING_SIZE;
- int rx_work_limit = tp->dirty_rx + RX_RING_SIZE - tp->cur_rx;
- int work_done = 0;
-
- if (xircom_debug > 4)
- printk(KERN_DEBUG " In xircom_rx(), entry %d %8.8x.\n", entry,
- tp->rx_ring[entry].status);
- /* If we own the next entry, it's a new packet. Send it up. */
- while (tp->rx_ring[entry].status >= 0) {
- s32 status = tp->rx_ring[entry].status;
-
- if (xircom_debug > 5)
- printk(KERN_DEBUG " In xircom_rx(), entry %d %8.8x.\n", entry,
- tp->rx_ring[entry].status);
- if (--rx_work_limit < 0)
- break;
- if ((status & 0x38008300) != 0x0300) {
- if ((status & 0x38000300) != 0x0300) {
- /* Ignore earlier buffers. */
- if ((status & 0xffff) != 0x7fff) {
- if (xircom_debug > 1)
- printk(KERN_WARNING "%s: Oversized Ethernet frame "
- "spanned multiple buffers, status %8.8x!\n",
- dev->name, status);
- tp->stats.rx_length_errors++;
- }
- } else if (status & Rx0DescError) {
- /* There was a fatal error. */
- if (xircom_debug > 2)
- printk(KERN_DEBUG "%s: Receive error, Rx status %8.8x.\n",
- dev->name, status);
- tp->stats.rx_errors++; /* end of a packet.*/
- if (status & (Rx0Runt | Rx0HugeFrame)) tp->stats.rx_length_errors++;
- if (status & Rx0CRCError) tp->stats.rx_crc_errors++;
- }
- } else {
- /* Omit the four octet CRC from the length. */
- short pkt_len = ((status >> 16) & 0x7ff) - 4;
- struct sk_buff *skb;
-
-#ifndef final_version
- if (pkt_len > 1518) {
- printk(KERN_WARNING "%s: Bogus packet size of %d (%#x).\n",
- dev->name, pkt_len, pkt_len);
- pkt_len = 1518;
- tp->stats.rx_length_errors++;
- }
-#endif
- /* Check if the packet is long enough to accept without copying
- to a minimally-sized skbuff. */
- if (pkt_len < rx_copybreak
- && (skb = dev_alloc_skb(pkt_len + 2)) != NULL) {
- skb->dev = dev;
- skb_reserve(skb, 2); /* 16 byte align the IP header */
-#if ! defined(__alpha__)
- eth_copy_and_sum(skb, bus_to_virt(tp->rx_ring[entry].buffer1),
- pkt_len, 0);
- skb_put(skb, pkt_len);
-#else
- memcpy(skb_put(skb, pkt_len),
- bus_to_virt(tp->rx_ring[entry].buffer1), pkt_len);
-#endif
- work_done++;
- } else { /* Pass up the skb already on the Rx ring. */
- skb_put(skb = tp->rx_skbuff[entry], pkt_len);
- tp->rx_skbuff[entry] = NULL;
- }
- skb->protocol = eth_type_trans(skb, dev);
- netif_rx(skb);
- dev->last_rx = jiffies;
- tp->stats.rx_packets++;
- tp->stats.rx_bytes += pkt_len;
- }
- entry = (++tp->cur_rx) % RX_RING_SIZE;
- }
-
- /* Refill the Rx ring buffers. */
- for (; tp->cur_rx - tp->dirty_rx > 0; tp->dirty_rx++) {
- entry = tp->dirty_rx % RX_RING_SIZE;
- if (tp->rx_skbuff[entry] == NULL) {
- struct sk_buff *skb;
- skb = tp->rx_skbuff[entry] = dev_alloc_skb(PKT_BUF_SZ);
- if (skb == NULL)
- break;
- skb->dev = dev; /* Mark as being used by this device. */
- tp->rx_ring[entry].buffer1 = virt_to_bus(skb->data);
- work_done++;
- }
- tp->rx_ring[entry].status = Rx0DescOwned;
- }
-
- return work_done;
-}
-
-
-static void
-xircom_down(struct net_device *dev)
-{
- long ioaddr = dev->base_addr;
- struct xircom_private *tp = netdev_priv(dev);
-
- /* Disable interrupts by clearing the interrupt mask. */
- outl(0, ioaddr + CSR7);
- /* Stop the chip's Tx and Rx processes. */
- outl_CSR6(inl(ioaddr + CSR6) & ~EnableTxRx, ioaddr);
-
- if (inl(ioaddr + CSR6) != 0xffffffff)
- tp->stats.rx_missed_errors += inl(ioaddr + CSR8) & 0xffff;
-
- dev->if_port = tp->saved_if_port;
-}
-
-
-static int
-xircom_close(struct net_device *dev)
-{
- long ioaddr = dev->base_addr;
- struct xircom_private *tp = netdev_priv(dev);
- int i;
-
- if (xircom_debug > 1)
- printk(KERN_DEBUG "%s: Shutting down ethercard, status was %2.2x.\n",
- dev->name, inl(ioaddr + CSR5));
-
- netif_stop_queue(dev);
-
- if (netif_device_present(dev))
- xircom_down(dev);
-
- free_irq(dev->irq, dev);
-
- /* Free all the skbuffs in the Rx queue. */
- for (i = 0; i < RX_RING_SIZE; i++) {
- struct sk_buff *skb = tp->rx_skbuff[i];
- tp->rx_skbuff[i] = NULL;
- tp->rx_ring[i].status = 0; /* Not owned by Xircom chip. */
- tp->rx_ring[i].length = 0;
- tp->rx_ring[i].buffer1 = 0xBADF00D0; /* An invalid address. */
- if (skb) {
- dev_kfree_skb(skb);
- }
- }
- for (i = 0; i < TX_RING_SIZE; i++) {
- if (tp->tx_skbuff[i])
- dev_kfree_skb(tp->tx_skbuff[i]);
- tp->tx_skbuff[i] = NULL;
- }
-
- tp->open = 0;
- return 0;
-}
-
-
-static struct net_device_stats *xircom_get_stats(struct net_device *dev)
-{
- struct xircom_private *tp = netdev_priv(dev);
- long ioaddr = dev->base_addr;
-
- if (netif_device_present(dev))
- tp->stats.rx_missed_errors += inl(ioaddr + CSR8) & 0xffff;
-
- return &tp->stats;
-}
-
-static int xircom_get_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
-{
- struct xircom_private *tp = netdev_priv(dev);
- ecmd->supported =
- SUPPORTED_10baseT_Half |
- SUPPORTED_10baseT_Full |
- SUPPORTED_100baseT_Half |
- SUPPORTED_100baseT_Full |
- SUPPORTED_Autoneg |
- SUPPORTED_MII;
-
- ecmd->advertising = ADVERTISED_MII;
- if (tp->advertising[0] & ADVERTISE_10HALF)
- ecmd->advertising |= ADVERTISED_10baseT_Half;
- if (tp->advertising[0] & ADVERTISE_10FULL)
- ecmd->advertising |= ADVERTISED_10baseT_Full;
- if (tp->advertising[0] & ADVERTISE_100HALF)
- ecmd->advertising |= ADVERTISED_100baseT_Half;
- if (tp->advertising[0] & ADVERTISE_100FULL)
- ecmd->advertising |= ADVERTISED_100baseT_Full;
- if (tp->autoneg) {
- ecmd->advertising |= ADVERTISED_Autoneg;
- ecmd->autoneg = AUTONEG_ENABLE;
- } else
- ecmd->autoneg = AUTONEG_DISABLE;
-
- ecmd->port = PORT_MII;
- ecmd->transceiver = XCVR_INTERNAL;
- ecmd->phy_address = tp->phys[0];
- ecmd->speed = tp->speed100 ? SPEED_100 : SPEED_10;
- ecmd->duplex = tp->full_duplex ? DUPLEX_FULL : DUPLEX_HALF;
- ecmd->maxtxpkt = TX_RING_SIZE / 2;
- ecmd->maxrxpkt = 0;
- return 0;
-}
-
-static int xircom_set_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
-{
- struct xircom_private *tp = netdev_priv(dev);
- u16 autoneg, speed100, full_duplex;
-
- autoneg = (ecmd->autoneg == AUTONEG_ENABLE);
- speed100 = (ecmd->speed == SPEED_100);
- full_duplex = (ecmd->duplex == DUPLEX_FULL);
-
- tp->autoneg = autoneg;
- if (speed100 != tp->speed100 ||
- full_duplex != tp->full_duplex) {
- tp->speed100 = speed100;
- tp->full_duplex = full_duplex;
- /* change advertising bits */
- tp->advertising[0] &= ~(ADVERTISE_10HALF |
- ADVERTISE_10FULL |
- ADVERTISE_100HALF |
- ADVERTISE_100FULL |
- ADVERTISE_100BASE4);
- if (speed100) {
- if (full_duplex)
- tp->advertising[0] |= ADVERTISE_100FULL;
- else
- tp->advertising[0] |= ADVERTISE_100HALF;
- } else {
- if (full_duplex)
- tp->advertising[0] |= ADVERTISE_10FULL;
- else
- tp->advertising[0] |= ADVERTISE_10HALF;
- }
- }
- check_duplex(dev);
- return 0;
-}
-
-static void xircom_get_drvinfo(struct net_device *dev, struct ethtool_drvinfo *info)
-{
- struct xircom_private *tp = netdev_priv(dev);
- strcpy(info->driver, DRV_NAME);
- strcpy(info->version, DRV_VERSION);
- strcpy(info->bus_info, pci_name(tp->pdev));
-}
-
-static struct ethtool_ops ops = {
- .get_settings = xircom_get_settings,
- .set_settings = xircom_set_settings,
- .get_drvinfo = xircom_get_drvinfo,
-};
-
-/* Provide ioctl() calls to examine the MII xcvr state. */
-static int xircom_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
-{
- struct xircom_private *tp = netdev_priv(dev);
- u16 *data = (u16 *)&rq->ifr_ifru;
- int phy = tp->phys[0] & 0x1f;
- unsigned long flags;
-
- switch(cmd) {
- /* Legacy mii-diag interface */
- case SIOCGMIIPHY: /* Get address of MII PHY in use. */
- if (tp->mii_cnt)
- data[0] = phy;
- else
- return -ENODEV;
- return 0;
- case SIOCGMIIREG: /* Read MII PHY register. */
- save_flags(flags);
- cli();
- data[3] = mdio_read(dev, data[0] & 0x1f, data[1] & 0x1f);
- restore_flags(flags);
- return 0;
- case SIOCSMIIREG: /* Write MII PHY register. */
- if (!capable(CAP_NET_ADMIN))
- return -EPERM;
- save_flags(flags);
- cli();
- if (data[0] == tp->phys[0]) {
- u16 value = data[2];
- switch (data[1]) {
- case 0:
- if (value & (BMCR_RESET | BMCR_ANENABLE))
- /* Autonegotiation. */
- tp->autoneg = 1;
- else {
- tp->full_duplex = (value & BMCR_FULLDPLX) ? 1 : 0;
- tp->autoneg = 0;
- }
- break;
- case 4:
- tp->advertising[0] = value;
- break;
- }
- check_duplex(dev);
- }
- mdio_write(dev, data[0] & 0x1f, data[1] & 0x1f, data[2]);
- restore_flags(flags);
- return 0;
- default:
- return -EOPNOTSUPP;
- }
-
- return -EOPNOTSUPP;
-}
-
-/* Set or clear the multicast filter for this adaptor.
- Note that we only use exclusion around actually queueing the
- new frame, not around filling tp->setup_frame. This is non-deterministic
- when re-entered but still correct. */
-static void set_rx_mode(struct net_device *dev)
-{
- struct xircom_private *tp = netdev_priv(dev);
- struct dev_mc_list *mclist;
- long ioaddr = dev->base_addr;
- int csr6 = inl(ioaddr + CSR6);
- u16 *eaddrs, *setup_frm;
- u32 tx_flags;
- int i;
-
- tp->csr6 &= ~(AllMultiBit | PromiscBit | HashFilterBit);
- csr6 &= ~(AllMultiBit | PromiscBit | HashFilterBit);
- if (dev->flags & IFF_PROMISC) { /* Set promiscuous. */
- tp->csr6 |= PromiscBit;
- csr6 |= PromiscBit;
- goto out;
- }
-
- if ((dev->mc_count > 1000) || (dev->flags & IFF_ALLMULTI)) {
- /* Too many to filter well -- accept all multicasts. */
- tp->csr6 |= AllMultiBit;
- csr6 |= AllMultiBit;
- goto out;
- }
-
- tx_flags = Tx1WholePkt | Tx1SetupPkt | PKT_SETUP_SZ;
-
- /* Note that only the low-address shortword of setup_frame is valid! */
- setup_frm = tp->setup_frame;
- mclist = dev->mc_list;
-
- /* Fill the first entry with our physical address. */
- eaddrs = (u16 *)dev->dev_addr;
- *setup_frm = cpu_to_le16(eaddrs[0]); setup_frm += 2;
- *setup_frm = cpu_to_le16(eaddrs[1]); setup_frm += 2;
- *setup_frm = cpu_to_le16(eaddrs[2]); setup_frm += 2;
-
- if (dev->mc_count > 14) { /* Must use a multicast hash table. */
- u32 *hash_table = (u32 *)(tp->setup_frame + 4 * 12);
- u32 hash, hash2;
-
- tx_flags |= Tx1HashSetup;
- tp->csr6 |= HashFilterBit;
- csr6 |= HashFilterBit;
-
- /* Fill the unused 3 entries with the broadcast address.
- At least one entry *must* contain the broadcast address!!!*/
- for (i = 0; i < 3; i++) {
- *setup_frm = 0xffff; setup_frm += 2;
- *setup_frm = 0xffff; setup_frm += 2;
- *setup_frm = 0xffff; setup_frm += 2;
- }
-
- /* Truly brain-damaged hash filter layout */
- /* XXX: not sure if I should take the last or the first 9 bits */
- for (i = 0; i < dev->mc_count; i++, mclist = mclist->next) {
- u32 *hptr;
- hash = ether_crc(ETH_ALEN, mclist->dmi_addr) & 0x1ff;
- if (hash < 384) {
- hash2 = hash + ((hash >> 4) << 4) +
- ((hash >> 5) << 5);
- } else {
- hash -= 384;
- hash2 = 64 + hash + (hash >> 4) * 80;
- }
- hptr = &hash_table[hash2 & ~0x1f];
- *hptr |= cpu_to_le32(1 << (hash2 & 0x1f));
- }
- } else {
- /* We have <= 14 mcast addresses so we can use Xircom's
- wonderful 16-address perfect filter. */
- for (i = 0; i < dev->mc_count; i++, mclist = mclist->next) {
- eaddrs = (u16 *)mclist->dmi_addr;
- *setup_frm = cpu_to_le16(eaddrs[0]); setup_frm += 2;
- *setup_frm = cpu_to_le16(eaddrs[1]); setup_frm += 2;
- *setup_frm = cpu_to_le16(eaddrs[2]); setup_frm += 2;
- }
- /* Fill the unused entries with the broadcast address.
- At least one entry *must* contain the broadcast address!!!*/
- for (; i < 15; i++) {
- *setup_frm = 0xffff; setup_frm += 2;
- *setup_frm = 0xffff; setup_frm += 2;
- *setup_frm = 0xffff; setup_frm += 2;
- }
- }
-
- /* Now add this frame to the Tx list. */
- if (tp->cur_tx - tp->dirty_tx > TX_RING_SIZE - 2) {
- /* Same setup recently queued, we need not add it. */
- /* XXX: Huh? All it means is that the Tx list is full...*/
- } else {
- unsigned long flags;
- unsigned int entry;
- int dummy = -1;
-
- save_flags(flags); cli();
- entry = tp->cur_tx++ % TX_RING_SIZE;
-
- if (entry != 0) {
- /* Avoid a chip errata by prefixing a dummy entry. */
- tp->tx_skbuff[entry] = NULL;
- tp->tx_ring[entry].length =
- (entry == TX_RING_SIZE - 1) ? Tx1RingWrap : 0;
- tp->tx_ring[entry].buffer1 = 0;
- /* race with chip, set Tx0DescOwned later */
- dummy = entry;
- entry = tp->cur_tx++ % TX_RING_SIZE;
- }
-
- tp->tx_skbuff[entry] = NULL;
- /* Put the setup frame on the Tx list. */
- if (entry == TX_RING_SIZE - 1)
- tx_flags |= Tx1RingWrap; /* Wrap ring. */
- tp->tx_ring[entry].length = tx_flags;
- tp->tx_ring[entry].buffer1 = virt_to_bus(tp->setup_frame);
- tp->tx_ring[entry].status = Tx0DescOwned;
- if (tp->cur_tx - tp->dirty_tx >= TX_RING_SIZE - 2) {
- tp->tx_full = 1;
- netif_stop_queue (dev);
- }
- if (dummy >= 0)
- tp->tx_ring[dummy].status = Tx0DescOwned;
- restore_flags(flags);
- /* Trigger an immediate transmit demand. */
- outl(0, ioaddr + CSR1);
- }
-
-out:
- outl_CSR6(csr6, ioaddr);
-}
-
-
-static struct pci_device_id xircom_pci_table[] = {
- { 0x115D, 0x0003, PCI_ANY_ID, PCI_ANY_ID, 0, 0, X3201_3 },
- {0},
-};
-MODULE_DEVICE_TABLE(pci, xircom_pci_table);
-
-
-#ifdef CONFIG_PM
-static int xircom_suspend(struct pci_dev *pdev, pm_message_t state)
-{
- struct net_device *dev = pci_get_drvdata(pdev);
- struct xircom_private *tp = netdev_priv(dev);
- printk(KERN_INFO "xircom_suspend(%s)\n", dev->name);
- if (tp->open)
- xircom_down(dev);
-
- pci_save_state(pdev);
- pci_disable_device(pdev);
- pci_set_power_state(pdev, 3);
-
- return 0;
-}
-
-
-static int xircom_resume(struct pci_dev *pdev)
-{
- struct net_device *dev = pci_get_drvdata(pdev);
- struct xircom_private *tp = netdev_priv(dev);
- printk(KERN_INFO "xircom_resume(%s)\n", dev->name);
-
- pci_set_power_state(pdev,0);
- pci_enable_device(pdev);
- pci_restore_state(pdev);
-
- /* Bring the chip out of sleep mode.
- Caution: Snooze mode does not work with some boards! */
- if (xircom_tbl[tp->chip_id].flags & HAS_ACPI)
- pci_write_config_dword(tp->pdev, PCI_POWERMGMT, 0);
-
- transceiver_voodoo(dev);
- if (xircom_tbl[tp->chip_id].flags & HAS_MII)
- check_duplex(dev);
-
- if (tp->open)
- xircom_up(dev);
- return 0;
-}
-#endif /* CONFIG_PM */
-
-
-static void __devexit xircom_remove_one(struct pci_dev *pdev)
-{
- struct net_device *dev = pci_get_drvdata(pdev);
-
- printk(KERN_INFO "xircom_remove_one(%s)\n", dev->name);
- unregister_netdev(dev);
- pci_release_regions(pdev);
- free_netdev(dev);
- pci_set_drvdata(pdev, NULL);
-}
-
-
-static struct pci_driver xircom_driver = {
- .name = DRV_NAME,
- .id_table = xircom_pci_table,
- .probe = xircom_init_one,
- .remove = __devexit_p(xircom_remove_one),
-#ifdef CONFIG_PM
- .suspend = xircom_suspend,
- .resume = xircom_resume
-#endif /* CONFIG_PM */
-};
-
-
-static int __init xircom_init(void)
-{
-/* when a module, this is printed whether or not devices are found in probe */
-#ifdef MODULE
- printk(version);
-#endif
- return pci_module_init(&xircom_driver);
-}
-
-
-static void __exit xircom_exit(void)
-{
- pci_unregister_driver(&xircom_driver);
-}
-
-module_init(xircom_init)
-module_exit(xircom_exit)
-
-/*
- * Local variables:
- * c-indent-level: 4
- * c-basic-offset: 4
- * tab-width: 4
- * End:
- */

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Next message: Adrian Bunk: "[RFC: 2.6 patch] remove drivers/net/eepro100.c"
Previous message: David Gibson: "[PATCH] Fix error handling with put_compat_statfs()"
Next in thread: Mark Lord: "Re: [RFC: 2.6 patch] remove drivers/net/tulip/xircom_tulip_cb.c"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]