PCI: Cannot allocate resource region 4 of device 0000:00:1d.0
From: Richard Hughes
Date: Sun Nov 27 2005 - 12:01:22 EST
On boot, I get the following warning on my Toshiba Satellite Pro A10:
PCI: Cannot allocate resource region 4 of device 0000:00:1d.0
This seems to match with:
00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM
(ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 03) (prog-if 00 [UHCI])
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 4: I/O ports at 1440 [size=32]
But USB1 and USB2 seems to work okay on this laptop, but I thought I
should report it to the list in case it's useful.
I've attached the full output of dmesg and lspci -vv
These have been produced using 2.6.14-1.1637_FC4 but this happens with
vanilla 2.6.14.3 too. I've also tried with older kernels and they all
seem to say the same.
Thanks for any pointers/help, and please cc me in any replies.
Richard Hughes
Linux version 2.6.14-1.1637_FC4 (bhcompile@xxxxxxxxxxxxxxxxxxxxxxxxxxx) (gcc version 4.0.1 20050727 (Red Hat 4.0.1-5)) #1 Wed Nov 9 18:19:37 EST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 00000000000eee00 (reserved)
BIOS-e820: 00000000000eee00 - 00000000000ef000 (ACPI NVS)
BIOS-e820: 00000000000ef000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000002ef40000 (usable)
BIOS-e820: 000000002ef40000 - 000000002ef50000 (ACPI data)
BIOS-e820: 000000002ef50000 - 000000002f000000 (reserved)
BIOS-e820: 00000000fec10000 - 00000000fec20000 (reserved)
BIOS-e820: 00000000feda0000 - 00000000fedc0000 (reserved)
BIOS-e820: 00000000ffb80000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
751MB LOWMEM available.
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 192320
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 188224 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 TOSHIB ) @ 0x000f0180
ACPI: RSDT (v001 TOSHIB 750 0x00970814 TASM 0x04010000) @ 0x2ef40000
ACPI: FADT (v002 TOSHIB 750 0x00970814 TASM 0x04010000) @ 0x2ef40058
ACPI: DBGP (v001 TOSHIB 750 0x00970814 TASM 0x04010000) @ 0x2ef400dc
ACPI: BOOT (v001 TOSHIB 750 0x00970814 TASM 0x04010000) @ 0x2ef40030
ACPI: DSDT (v001 TOSHIB AFCF7 0x20030326 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0xd808
Allocating PCI resources starting at 30000000 (gap: 2f000000:cfc10000)
Built 1 zonelists
Kernel command line: ro root=LABEL=/ rhgb quiet acpi=force
Initializing CPU#0
CPU 0 irqstacks, hard=c03f4000 soft=c03f3000
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2194.738 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 757960k/769280k available (2108k kernel code, 10756k reserved, 713k data, 172k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 4394.77 BogoMIPS (lpj=8789544)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebf9ff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: After vendor identify, caps: bfebf9ff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 256K
CPU: After all inits, caps: bfebf1ff 00000000 00000000 00000080 00004400 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
mtrr: v2.0 (20020519)
CPU: Intel Mobile Intel(R) Celeron(R) CPU 2.20GHz stepping 09
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0e00)
checking if image is initramfs... it is
Freeing initrd memory: 512k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd317, last bus=3
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs *10)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *11)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *11)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *11)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *11)
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Boot video device is 0000:00:02.0
PCI quirk: region d800-d87f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region eec0-eeff claimed by ICH4 GPIO
PCI: Enabled i801 SMBus device
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: Power Resource [PFAN] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Cannot allocate resource region 4 of device 0000:00:1d.0
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bus 2, cardbus bridge: 0000:01:0b.0
IO window: 0000c000-0000c0ff
IO window: 0000c400-0000c4ff
PREFETCH window: 38000000-39ffffff
MEM window: 3c000000-3dffffff
PCI: Bridge: 0000:00:1e.0
IO window: c000-cfff
MEM window: cff00000-cfffffff
PREFETCH window: 38000000-39ffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PCI: Enabling device 0000:01:0b.0 (0000 -> 0003)
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
Simple Boot Flag at 0x7c set to 0x1
apm: BIOS version 1.2 Flags 0x02 (Driver version 1.16ac)
apm: overridden by ACPI.
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 2A9D19A62139EA9
- User ID: Red Hat, Inc. (Kernel Module GPG key)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Fan [FAN] (off)
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Thermal Zone [THRM] (60 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 855 Chipset.
agpgart: Detected 16252K stolen memory.
agpgart: AGP aperture is 128M @ 0xd8000000
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 32 ports, IRQ sharing enabled
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
ICH4: chipset revision 3
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xbfa0-0xbfa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xbfa8-0xbfaf, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: TOSHIBA MK2023GAS, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: TOSHIBA DVD-ROM SD-C2612, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 39070080 sectors (20003 MB), CHS=38760/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 < hda5 hda6 hda7 >
hdc: ATAPI 24X DVD-ROM drive, 192kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 3.39
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard on isa0060/serio0
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 8, 1310720 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
ACPI wakeup devices:
MPC0 MPC1 LAN VIY0 USB1 USB4 AMDM LID PWRB
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 172k freed
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
input: PS/2 Mouse on isa0060/serio1
input: AlpsPS/2 ALPS GlidePoint on isa0060/serio1
security: 3 users, 6 roles, 882 types, 107 bools
security: 55 classes, 241893 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev hda5, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses genfs_contexts
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
cdrom: open failed.
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
e100: Intel(R) PRO/100 Network Driver, 3.4.14-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [LNKE] -> GSI 11 (level, low) -> IRQ 11
e100: eth0: e100_probe: addr 0xcffff000, irq 11, MAC addr 00:00:39:D8:CB:2E
PCI: Enabling device 0000:00:1f.5 (0000 -> 0003)
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 54224 usecs
intel8x0: clocking to 48000
i8xx TCO timer: initialized (0xd860). heartbeat=30 sec (nowayout=0)
hw_random: RNG not detected
intelfb: Framebuffer driver for Intel(R) 830M/845G/852GM/855GM/865G/915G chipsets
intelfb: Version 0.9.2
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
intelfb: 00:02.0: Intel(R) 852GM, aperture size 128MB, stolen memory 16252kB
intelfb: Non-CRT device is enabled ( LVDS port ). Disabling mode switching.
intelfb: Video mode must be programmed at boot time.
PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: irq 11, io mem 0x3a080000
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 10, io base 0x00001440
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-1: new high speed USB device using ehci_hcd and address 2
ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:01:0b.0 [1179:0001]
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
Yenta: ISA IRQ mask 0x00b8, PCI irq 11
Socket status: 30000011
pcmcia: parent PCI bridge I/O window: 0xc000 - 0xcfff
cs: IO port probe 0xc000-0xcfff: clean.
pcmcia: parent PCI bridge Memory window: 0xcff00000 - 0xcfffffff
pcmcia: parent PCI bridge Memory window: 0x38000000 - 0x39ffffff
usb 1-1.2: new high speed USB device using ehci_hcd and address 3
usb 1-1.3: new low speed USB device using ehci_hcd and address 4
SCSI subsystem initialized
input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:1d.7-1.3
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
cs: memory probe 0xcff00000-0xcfffffff: excluding 0xcff00000-0xcff0ffff 0xcfff0000-0xcfffffff
eth1: MAC address 00:30:bd:d2:8e:78
eth1: Atmel at76c50x wireless. Version 0.96 simon@xxxxxxxxxxxxxxxxx
eth1: Belkin F5D6020-V2 index 0x01: Vcc 5.0, irq 3, io 0xc100-0xc11f
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
Vendor: LITE-ON Model: DVDRW SOHW-1673S Rev: JS0B
Type: CD-ROM ANSI SCSI revision: 00
usb-storage: device scan complete
sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03812a0(lo)
IPv6 over IPv4 tunneling driver
ip_tables: (C) 2000-2002 Netfilter core team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.3 (6010 buckets, 48080 max) - 236 bytes per conntrack
eth0: no IPv6 routers present
ACPI: AC Adapter [ADP1] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Power Button (CM) [PWRB]
ibm_acpi: ec object not found
toshiba_acpi: Toshiba Laptop ACPI Extras version 0.18
toshiba_acpi: HCI method: \_SB_.VALD.GHCI
ACPI: Video Device [VGA] (multi-head: yes rom: yes post: no)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@xxxxxxxxxx
eth1: no IPv6 routers present
cdrom: open failed.
EXT3 FS on hda5, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev hda2, type ext3), uses xattr
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev hda6, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
Adding 787144k swap on /dev/hda7. Priority:-1 extents:1 across:787144k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
Removing netfilter NETLINK layer.
ip_tables: (C) 2000-2002 Netfilter core team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.3 (6010 buckets, 48080 max) - 236 bytes per conntrack
pnp: Evaluate _CRS failed
pnp: Failed to activate device 00:08.
parport_pc: probe of 00:08 failed with error -5
lp: driver loaded but no devices found
[drm] Initialized drm 1.0.0 20040925
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
[drm] Initialized i915 1.1.0 20040405 on minor 0:
PCI: Enabling device 0000:00:02.1 (0000 -> 0002)
[drm] Initialized i915 1.1.0 20040405 on minor 1:
mtrr: base(0xd8020000) is not aligned on a size(0x300000) boundary
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on hda1, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev hda1, type ext3), uses xattr
application mixer_applet2 uses obsolete OSS audio interface
eth1: no IPv6 routers present
00:00.0 Host bridge: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 01)
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at <unassigned> (32-bit, prefetchable)
Capabilities: [40] Vendor Specific Information
00:00.1 System peripheral: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 01)
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:00.3 System peripheral: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 01)
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:02.0 VGA compatible controller: Intel Corporation 82852/855GM Integrated Graphics Device (rev 01) (prog-if 00 [VGA])
Subsystem: Toshiba America Info Systems: Unknown device 0002
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at d0000000 (32-bit, non-prefetchable) [size=512K]
Region 2: I/O ports at eff8 [size=8]
Capabilities: [d0] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.1 Display controller: Intel Corporation 82852/855GM Integrated Graphics Device (rev 01)
Subsystem: Toshiba America Info Systems: Unknown device 0002
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Region 0: Memory at 30000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at 3a000000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [d0] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 03) (prog-if 00 [UHCI])
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 4: I/O ports at 1440 [size=32]
00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 03) (prog-if 20 [EHCI])
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 11
Region 0: Memory at 3a080000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 83) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Latency: 0
Bus: primary=00, secondary=01, subordinate=03, sec-latency=64
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: cff00000-cfffffff
Prefetchable memory behind bridge: 38000000-39ffffff
Secondary status: 66Mhz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge (rev 03)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev 03) (prog-if 8a [Master SecP PriP])
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at <ignored>
Region 1: I/O ports at <ignored>
Region 2: I/O ports at <ignored>
Region 3: I/O ports at <ignored>
Region 4: I/O ports at bfa0 [size=16]
Region 5: Memory at 3a080400 (32-bit, non-prefetchable) [size=1K]
00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 03)
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 0
Region 4: I/O ports at d880 [size=32]
00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 03)
Subsystem: Toshiba America Info Systems: Unknown device 0241
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 0: I/O ports at 1000 [size=256]
Region 1: I/O ports at 1400 [size=64]
Region 2: Memory at 3a080800 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at 3a080a00 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:08.0 Ethernet controller: Intel Corporation 82801DB PRO/100 VE (MOB) Ethernet Controller (rev 83)
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min, 14000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at cffff000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at cf40 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
01:0b.0 CardBus bridge: Toshiba America Info Systems ToPIC100 PCI to Cardbus Bridge with ZV Support (rev 33)
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 11
Region 0: Memory at cff00000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=01, secondary=02, subordinate=05, sec-latency=0
Memory window 0: 38000000-39fff000 (prefetchable)
Memory window 1: 3c000000-3dfff000
I/O window 0: 0000c000-0000c0ff
I/O window 1: 0000c400-0000c4ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001