2.6.16-rc3 - sata_mv - Assertion failed!
From: Sander
Date: Fri Feb 17 2006 - 04:35:10 EST
Hi Jeff and others,
I get some error messages while using a raid5 over nine Maxtor 500GB
disks.
The first three disks are connected to the onboard nForce4, and six to a
MV88SX6081 8-port SATA II PCI-X Controller (rev 09)
I made a 25GB partition on each disk, and create raid5 over them:
mdadm -C -l5 -n9 /dev/md1 /dev/sda2 /dev/sdb2 /dev/sdc2 \
/dev/sdd2 /dev/sde2 /dev/sdf2 /dev/sdg2 /dev/sdh2 /dev/sdi2
When the recovery is finished, I create an ext3 filesystem, and mount
it:
mke2fs -j -m1 /dev/md1
mount -o data=writeback /dev/md1 /mnt
Then I execute the following:
for i in `seq 10`
do dd if=/dev/zero of=bigfile.$i bs=1024k count=10000
done
md5sum bigfile.*
rm bigfile.*
This time, the system was building another raid5 on other partitions at
the same time, generating some extra load. The system spits out error
messages (via netconsole), and responds _very_ slow on disks activity.
I rebuilded 2.6.16-rc3 with ATA_DEBUG and ATA_VERBOSE_DEBUG defined, but
that kernel hangs when I try to create the raid5. I'll try again with
only ATA_DEBUG enabled.
I'll also have a look at the firmware version in the Marvell controller,
and upgrade it if it is not the latest.
Any more I can do? More info I can provide? Is this due to the sata_mv
driver being beta? If so, I love to test any patches. All disks passed
badblocks in write mode, fwiw.
Sander
[ 0.000000] Linux version 2.6.16-rc3 (root@elisha) (gcc version 4.0.3 20060104 (prerelease) (Debian 4.0.2-6)) #1 SMP Wed Feb 15 17:07:29 CET 2006
[cut]
[ 78.285313] ata2: SATA link down (SStatus 0)
[ 78.285361] scsi1 : sata_nv
[ 78.285495] Vendor: ATA Model: Maxtor 7H500F0 Rev: HA43
[ 78.286242] Type: Direct-Access ANSI SCSI revision: 05
[ 78.286795] ACPI: PCI Interrupt Link [LSI1] enabled at IRQ 22
[ 78.286846] GSI 20 sharing vector 0xD1 and IRQ 20
[ 78.286894] ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LSI1] -> GSI 22 (level, high) -> IRQ 20
[ 78.287266] ata3: SATA max UDMA/133 cmd 0x1458 ctl 0x144E bmdma 0x1420 irq 20
[ 78.287344] ata4: SATA max UDMA/133 cmd 0x1450 ctl 0x144A bmdma 0x1428 irq 20
[ 78.505038] ata3: SATA link up 3.0 Gbps (SStatus 123)
[ 78.704878] ata3: dev 0 ATA-7, max UDMA/133, 976773168 sectors: LBA48
[ 78.705922] nv_sata: Primary device added
[ 78.705926] ata3: dev 0 configured for UDMA/133
[ 78.705929] scsi2 : sata_nv
[ 78.706065] nv_sata: Primary device removed
[ 78.706110] nv_sata: Secondary device added
[ 78.706154] nv_sata: Secondary device removed
[ 78.924512] ata4: SATA link up 3.0 Gbps (SStatus 123)
[ 79.114363] ata4: dev 0 ATA-7, max UDMA/133, 976773168 sectors: LBA48
[ 79.115391] nv_sata: Primary device added
[ 79.115394] ata4: dev 0 configured for UDMA/133
[ 79.115396] scsi3 : sata_nv
[ 79.115520] nv_sata: Primary device removed
[ 79.115564] nv_sata: Secondary device added
[ 79.115609] nv_sata: Secondary device removed
[ 79.115725] Vendor: ATA[ 80.033304] ata6: dev 0 ATA-7, max UDMA/133, 976773168 sectors: LBA48
[ 80.034353] ata6: dev 0 configured for UDMA/133
[ 80.034397] scsi5 : sata_mv
[ 80.492731] ata7: dev 0 ATA-7, max UDMA/133, 976773168 sectors: LBA48
[ 80.493771] ata7: dev 0 configured for UDMA/133
[ 80.493815] scsi6 : sata_mv
[ 80.952151] ata8: dev 0 ATA-7, max UDMA/133, 976773168 sectors: LBA48
[ 80.953186] ata8: dev 0 configured for UDMA/133
[ 80.953231] scsi7 : sata_mv
[ 81.411574] ata9: dev 0 ATA-7, max UDMA/133, 976773168 sectors: LBA48
[ 81.412605] ata9: dev 0 configured for UDMA/133
[ 81.412650] scsi8 : sata_mv
[ 81.880985] ata10: dev 0 ATA-7, max UDMA/133, 976773168 sectors: LBA48
[ 81.882022] ata10: dev 0 configured for UDMA/133
[ 81.882066] scsi9 : sata_mv
[ 81.940725] ata11: no device found (phy stat 00000000)
[ 81.940773] scsi10 : sata_mv
[ 81.990662] ata12: no device found (phy stat 00000000)
[ 81.990709] scsi11 : sata_mv
[ 81.990839] Vendor: ATA Model: Maxtor 7H500F0 Rev: HA43
[ 81.991587] Type: Direct-Access ANSI SCSI revision: 05
[ 81.991795] Vendor: ATA Model: Maxtor 7H[ 82.879567] Driver 'w83627hf' needs updating - please use bus_type methods
[cut]
[ 2071.503963] ata5: translated ATA stat/err 0xd0/00 to SCSI SK/ASC/ASCQ 0xb/47/00
[ 2071.504017] ata5: status=0xd0 { Busy }
[ 2101.475022] ata5: Entering mv_eng_timeout
[ 2101.475059] mmio_base ffffc20000080000 ap ffff81013b4a5480 qc ffff81013b4a59b8 scsi_cmnd ffff810116d70b40 &cmnd ffff810116d70bb0
[ 2101.538621] ata5: no device found (phy stat 00000100)
[ 2101.601492] ata5: status=0x50 { DriveReady SeekComplete }
[ 2101.601540] ata5: error=0x01 { AddrMarkNotFound }
[ 2101.601578] Assertion failed! qc->flags & ATA_QCFLAG_ACTIVE,drivers/scsi/libata-core.c,ata_qc_complete,line=3623
[ 2101.601637] ata5: status=0x50 { DriveReady SeekComplete }
[ 2101.601675] ata5: error=0x01 { AddrMarkNotFound }
[ 2101.601713] sdd: Current: sense key=0x0
[ 2101.601742] ASC=0x0 ASCQ=0x0
[ 2101.601856] Assertion failed! ((in_ptr >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK) == ((readl(port_mmio + EDMA_REQ_Q_OUT_PTR_OFS) >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK),drivers/scsi/sata_mv.c,mv_qc_issue,line=1073
[ 2131.567227] ata5: Entering mv_eng_timeout
[ 2131.567259] mmio_base ffffc20000080000 ap ffff81013b4a5480 qc ffff81013b4a59b8 scsi_cmnd ffff81010b7489c0 &cmnd ffff81010b748a30
[ 2131.651702] ata5: no device found (phy stat 00000100)
[ 2131.693584] Assertion failed! qc->flags & ATA_QCFLAG_ACTIVE,drivers/scsi/libata-core.c,ata_qc_complete,line=3623
[ 2131.693640] ata5: status=0x50 { DriveReady SeekComplete }
[ 2131.693677] ata5: error=0x01 { AddrMarkNotFound }
[ 2131.693712] sdd: Current: sense key=0x0
[ 2131.693741] ASC=0x0 ASCQ=0x0
[ 2131.693856] Assertion failed! ((in_ptr >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK) == ((readl(port_mmio + EDMA_REQ_Q_OUT_PTR_OFS) >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK),drivers/scsi/sata_mv.c,mv_qc_issue,line=1073
[ 2161.689415] ata5: Entering mv_eng_timeout
[ 2161.689447] mmio_base ffffc20000080000 ap ffff81013b4a5480 qc ffff81013b4a59b8 scsi_cmnd ffff81010b7489c0 &cmnd ffff81010b748a30
[ 2161.773886] ata5: no device found (phy stat 00000100)
[ 2161.815776] ata5: status=0x50 { DriveReady SeekComplete }
[ 2161.815823] ata5: error=0x01 { AddrMarkNotFound }
[ 2161.815859] Assertion failed! qc->flags & ATA_QCFLAG_ACTIVE,drivers/scsi/libata-core.c,ata_qc_complete,line=3623
[ 2161.815917] ata5: status=0x50 { DriveReady SeekComplete }
[ 2161.815954] ata5: error=0x01 { AddrMarkNotFound }
[ 2161.815989] sdd: Current: sense key=0x0
[ 2161.816018] ASC=0x0 ASCQ=0x0
[ 2161.816122] Assertion failed! ((in_ptr >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK) == ((readl(port_mmio + EDMA_REQ_Q_OUT_PTR_OFS) >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK),drivers/scsi/sata_mv.c,mv_qc_issue,line=1073
[ 2191.781622] ata5: Entering mv_eng_timeout
[ 2191.781654] mmio_base ffffc20000080000 ap ffff81013b4a5480 qc ffff81013b4a59b8 scsi_cmnd ffff810116d70b40 &cmnd ffff810116d70bb0
[ 2191.866094] ata5: no device found (phy stat 00000100)
[ 2191.907980] ata5: status=0x50 { DriveReady SeekComplete }
[ 2191.908020] ata5: error=0x01 { AddrMarkNotFound }
[ 2191.908056] Assertion failed! qc->flags & ATA_QCFLAG_ACTIVE,drivers/scsi/libata-core.c,ata_qc_complete,line=3623
[ 2191.908115] ata5: status=0x50 { DriveReady SeekComplete }
[ 2191.908151] ata5: error=0x01 { AddrMarkNotFound }
[ 2191.908188] sdd: Current: sense key=0x0
[ 2191.908217] ASC=0x0 ASCQ=0x0
[ 2191.908305] Assertion failed! ((in_ptr >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK) == ((readl(port_mmio + EDMA_REQ_Q_OUT_PTR_OFS) >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK),drivers/scsi/sata_mv.c,mv_qc_issue,line=1073
[ 2221.873842] ata5: Entering mv_eng_timeout
[ 2221.877167] mmio_base ffffc20000080000 ap ffff81013b4a5480 qc ffff81013b4a59b8 scsi_cmnd ffff81010b7489c0 &cmnd ffff81010b748a30
[cut the same over and over]
--
Humilis IT Services and Solutions
http://www.humilis.net
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/