Re: Help: DGE-560T not recognized by Linux

[Randy.Dunlap]

On Fri, 17 Feb 2006 22:27:20 -0700 Brian Hall wrote:

> 
> I have just built a new system, based on an Asrock 939Dual-Sata
> motherboard. It only has 100MB built-in networking (uli526x), so I
> purchased a D-Link DGE-560T PCI-e gigabit NIC ($81 at Newegg) thinking
> it was supported by Linux. Looking at the card, it appears to be a
> Marvell chip, but neither the sk98lin or skge drivers worked. I tried
> other GBe drivers as well, they didn't recognize it either.
> 
> Is there a place where I can just add this card's ID and use one of the
> sk* drivers? I paged through the source but didn't see an obvious place
> to add a card ID, but it must be in there somewhere.

The sky2 driver seems to support this device.
drivers/net/sky2.c
in very recent kernels.

> I'm not subscribed to linux-kernel, please CC: me on replies, thanks.
> 
> Here's the info from the card:
> big M on the chip (Marvell I assume)
> 88E8052-NNC
> GMAA17011A1
> 0442 A2P
> 
> and on the back of the card:
> 
> 00005A708649 0592
> DLink
> 531CL00467 DGE-560T 70-13-001-001
> 
> from lspci:
> 
> 02:00.0 0200: 1186:4b00 (rev 11)
> 	Subsystem: 1186:4b00
> 
> 02:00.0 Ethernet controller: D-Link System Inc Unknown device 4b00 (rev
> 11) Subsystem: D-Link System Inc Unknown device 4b00
> 	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B-
> ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR+ <PERR- Latency:
> 0, Cache Line Size 10 Interrupt: pin A routed to IRQ 11
> 	Region 0: Memory at ff3fc000 (64-bit, non-prefetchable)
> [size=16K] Region 2: I/O ports at 9800 [size=256]
> 	Expansion ROM at 50000000 [disabled] [size=128K]
> 	Capabilities: [48] Power Management version 2
> 		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1
> +,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=1 PME-
> 	Capabilities: [50] Vital Product Data
> 	Capabilities: [5c] Message Signalled Interrupts: 64bit+
> Queue=0/1 Enable- Address: 0000000000000000  Data: 0000
> 	Capabilities: [e0] Express Legacy Endpoint IRQ 0
> 		Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
> ExtTag- Device: Latency L0s unlimited, L1 unlimited
> 		Device: AtnBtn- AtnInd- PwrInd-
> 		Device: Errors: Correctable- Non-Fatal- Fatal-
> Unsupported- Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr+ NoSnoop-
> 		Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
> 		Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port
> 214 Link: Latency L0s <256ns, L1 unlimited
> 		Link: ASPM Disabled RCB 128 bytes CommClk- ExtSynch-
> 		Link: Speed 2.5Gb/s, Width x1


---
~Randy
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/