Re: [PATCHSET] Announce: High-res timers,tickless/dyntick and dynamic HZ -V4
From: Robert Hancock
Date: Fri Jun 23 2006 - 20:52:26 EST
Thomas Gleixner wrote:
On Thu, 2006-06-22 at 21:31 -0600, Robert Hancock wrote:
Thomas Gleixner wrote:
An updated patchset is available from:
http://www.tglx.de/projects/hrtimers/2.6.17/patch-2.6.17-hrt-dyntick4.patch
On my Compaq Presario X1050 laptop running Fedora Core 5 I get:
Disabling NO_HZ and high resolution timers due to timer broadcasting
Not sure exactly what this is indicating or what's triggered this, but
I'm assuming the patch isn't doing much on this machine?
The system is configured for SMP, but this is an UP machine and the APIC
is disabled in the BIOS. Linux uses then the PIT and an IPI mechanism to
broadcast timer events. We need to do the event reprogramming per CPU,
so we switch off in that situation.
Solution: Either use an UP kernel, or enable Local APIC in the BIOS (is
not possible in most BIOSes), or add "lapic" to the kernel command line.
Also for an UP kernel adding "lapic" to the commandline is good, as the
APIC is faster accessible than the PIT.
Tried that, still no dice:
Kernel command line: ro root=/dev/VolGroup00/LogVol00 lapic
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
...
Disabling NO_HZ and high resolution timers due to timer broadcasting
This isn't a viable solution for all machines anyway - some laptops
disable the local APIC and the BIOS expects it to remain that way, and
blows up if it gets turned on.
I also saw a problem with suspend-to-disk, it locked up the machine. The
screen was already blanked so I couldn't tell if there was any output.
It could be the libata PATA patch as well, I'm building a new kernel
without the hrt patch now to try it..
Full output:
Linux version 2.6.17-1.2138_FC5idehrt (rob@xxxxxxxxxxxxxxxxxxxxx) (gcc
version 4.1.1 20060525 (Red Hat 4.1.1-1)) #1 SMP Thu Jun 22 20:52:49 CST
2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ffd0000 (usable)
BIOS-e820: 000000001ffd0000 - 000000001fff0c00 (reserved)
BIOS-e820: 000000001fff0c00 - 000000001fffc000 (ACPI NVS)
BIOS-e820: 000000001fffc000 - 0000000020000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 131024
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 126928 pages, LIFO batch:31
DMI 2.3 present.
Using APIC driver default
ACPI: RSDP (v000 COMPAQ ) @ 0x000f6560
ACPI: RSDT (v001 HP CPQ0860 0x14070520 CPQ 0x00000001) @ 0x1fff0c84
ACPI: FADT (v002 HP CPQ0860 0x00000002 CPQ 0x00000001) @ 0x1fff0c00
ACPI: SSDT (v001 COMPAQ CPQGysr 0x00001001 MSFT 0x0100000e) @ 0x1fff5c3c
ACPI: DSDT (v001 HP nx7000 0x00010000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
Allocating PCI resources starting at 30000000 (gap: 20000000:e0000000)
Detected 598.093 MHz processor.
Built 1 zonelists
Kernel command line: ro root=/dev/VolGroup00/LogVol00 lapic
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
mapped APIC to ffffd000 (fee00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
Event source pit configured with caps set: 07
CPU 0 irqstacks, hard=c079f000 soft=c077f000
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 511860k/524096k available (2101k kernel code, 11536k reserved,
1197k data, 240k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1197.22 BogoMIPS
(lpj=2394455)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: a7e9fbbf 00000000 00000000 00000000
00000180 00000000 00000000
CPU: After vendor identify, caps: a7e9fbbf 00000000 00000000 00000000
00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: After all inits, caps: a7e9f3bf 00000000 00000000 00000040 00000180
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 16k freed
ACPI: setting ELCR to 0200 (from 0c20)
CPU0: Intel(R) Pentium(R) M processor 1400MHz stepping 05
SMP motherboard not detected.
lapic max_delta_ns: 1346559260
Event source pit new caps set: 01
Event source lapic configured with caps set: 06
Brought up 1 CPUs
checking if image is initramfs... it is
Freeing initrd memory: 1665k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf031f, last bus=3
Setting up standard PCI resources
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [C046] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.C046] bus is 0
PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 1100-113f claimed by ICH4 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #03 (-#06) is hidden behind transparent bridge #02 (-#03) (try
'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.C046._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.C046.C047._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.C046.C058._PRT]
ACPI: Embedded Controller [C0EA] (gpe 28) interrupt mode.
ACPI: Power Resource [C18D] (on)
ACPI: Power Resource [C195] (on)
ACPI: Power Resource [C19C] (on)
ACPI: Power Resource [C1A6] (on)
ACPI: PCI Interrupt Link [C0C2] (IRQs 5 *10)
ACPI: PCI Interrupt Link [C0C3] (IRQs 5 *10)
ACPI: PCI Interrupt Link [C0C4] (IRQs *5 10)
ACPI: PCI Interrupt Link [C0C5] (IRQs *5 10)
ACPI: PCI Interrupt Link [C0C6] (IRQs 5 10) *0, disabled.
ACPI: PCI Interrupt Link [C0C7] (IRQs 5 10) *11
ACPI: PCI Interrupt Link [C0C8] (IRQs 5 10) *0, disabled.
ACPI: PCI Interrupt Link [C0C9] (IRQs *5 10)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 15 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report
pnp: 00:0d: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:0d: ioport range 0x1000-0x107f could not be reserved
pnp: 00:0d: ioport range 0x1100-0x113f has been reserved
pnp: 00:0d: ioport range 0x1200-0x121f has been reserved
PCI: Bridge: 0000:00:01.0
IO window: 3000-3fff
MEM window: 90400000-904fffff
PREFETCH window: 98000000-9fffffff
PCI: Bus 3, cardbus bridge: 0000:02:04.0
IO window: 00002800-000028ff
IO window: 00002c00-00002cff
PREFETCH window: 30000000-31ffffff
MEM window: 34000000-35ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 2000-2fff
MEM window: 90000000-903fffff
PREFETCH window: 30000000-31ffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt Link [C0C4] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [C0C4] -> GSI 5 (level, low)
-> IRQ 5
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 6, 327680 bytes)
TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1151088082.560:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Disabling NO_HZ and high resolution timers due to timer broadcasting
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 855PM Chipset.
agpgart: AGP aperture is 256M @ 0xb0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS2 at I/O 0x3e8 (irq = 3) is a 16550A
00:03: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt Link [C0C3] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [C0C3] -> GSI 10 (level,
low) -> IRQ 10
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
libata version 1.20 loaded.
ata_piix 0000:00:1f.1: version 1.05-ac7
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [C0C4] -> GSI 5 (level, low)
-> IRQ 5
PCI: Setting latency timer of device 0000:00:1f.1 to 64
ata1: PATA max UDMA/100 cmd 0x1F0 ctl 0x3F6 bmdma 0x4C40 irq 14
ata1: dev 0 cfg 49:2f00 82:346b 83:7f09 84:6003 85:3c69 86:3e01 87:6003
88:203f
ata1: dev 0 ATA-7, max UDMA/100, 156368016 sectors: LBA48
ata1: dev 0 configured for UDMA/100
scsi0 : ata_piix
Vendor: ATA Model: SAMSUNG MP0804H Rev: UE20
Type: Direct-Access ANSI SCSI revision: 05
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x4C48 irq 15
ata2: dev 0 cfg 49:0f00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000
88:0407
ata2: dev 0 ATAPI, max UDMA/33
ata2: dev 0 configured for UDMA/33
scsi1 : ata_piix
Vendor: QSI Model: CDRW/DVD SBW-241 Rev: VH04
Type: CD-ROM ANSI SCSI revision: 05
SCSI device sda: 156368016 512-byte hdwr sectors (80060 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 156368016 512-byte hdwr sectors (80060 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [C0C4] -> GSI 5 (level, low)
-> IRQ 5
Yenta: CardBus bridge found at 0000:02:04.0 [0e11:0860]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.0, mfunc 0x001c1112, devctl 0x44
Yenta: ISA IRQ mask 0x08d8, PCI irq 5
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff
cs: IO port probe 0x2000-0x2fff: clean.
pcmcia: parent PCI bridge Memory window: 0x90000000 - 0x903fffff
pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x31ffffff
usbcore: registered new driver libusual
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:C1A3,PNP0f13:C1A4] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
ACPI wakeup devices:
C058 C1AD C1A3 C1A4 C0AC C0B3 C0B4 C0B5 C0E7 C136
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 240k freed
Write protecting the kernel read-only data: 737k
Time: tsc clocksource has been installed.
Time: acpi_pm clocksource has been installed.
input: AT Translated Set 2 keyboard as /class/input/input0
device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel@xxxxxxxxxx
Synaptics Touchpad, model: 1, fw: 5.9, id: 0x236eb3, caps: 0x904713/0x10008
input: SynPS/2 Synaptics TouchPad as /class/input/input1
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
audit(1151088086.844:2): enforcing=1 old_enforcing=0 auid=4294967295
security: 3 users, 6 roles, 1417 types, 151 bools, 1 sens, 256 cats
security: 57 classes, 41080 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev dm-0, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses
genfs_contexts
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev cpuset, type cpuset), not configured for labeling
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
audit(1151088087.316:3): policy loaded auid=4294967295
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
hw_random: cannot enable RNG, aborting
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [C0C3] -> GSI 10 (level,
low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1f.6 to 64
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [C0C3] -> GSI 10 (level,
low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 54449 usecs
intel8x0: clocking to 48000
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [C0C3] -> GSI 10 (level,
low) -> IRQ 10
eth0: RTL-8139C+ at 0xe0926000, 00:02:3f:65:4d:74, IRQ 10
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, git-1.1.7
ieee80211: Copyright (C) 2004-2005 Intel Corporation
<jketreno@xxxxxxxxxxxxxxx>
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, git-1.1.1
ipw2200: Copyright(c) 2003-2006 Intel Corporation
ACPI: PCI Interrupt Link [C0C5] enabled at IRQ 5
ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [C0C5] -> GSI 5 (level, low)
-> IRQ 5
ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
cs: IO port probe 0x100-0x3af: excluding 0x140-0x14f 0x200-0x20f 0x370-0x37f
cs: IO port probe 0x3e0-0x4ff: excluding 0x3f0-0x3ff
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
Floppy drive(s): fd0 is 1.44M
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 1:0:0:0: Attached scsi generic sg1 type 5
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [C0C2] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [C0C2] -> GSI 10 (level,
low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 10, io base 0x000048c0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [C0C5] -> GSI 5 (level, low)
-> IRQ 5
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 5, io base 0x000048e0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [C0C4] -> GSI 5 (level, low)
-> IRQ 5
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 5, io base 0x00004c00
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ieee1394: Initialized config rom entry `ip1394'
floppy0: no floppy controllers found
ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
ACPI: PCI Interrupt Link [C0C9] enabled at IRQ 5
ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [C0C9] -> GSI 5 (level, low)
-> IRQ 5
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 5, io mem 0xa0000000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [C0C2] -> GSI 10 (level,
low) -> IRQ 10
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10]
MMIO=[90200000-902007ff] Max Packet=[2048] IR/IT contexts=[4/8]
Floppy drive(s): fd0 is 1.44M
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023f383800c298]
floppy0: no floppy controllers found
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
lp0: console ready
ACPI: AC Adapter [C134] (off-line)
ACPI: Battery Slot [C11F] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [C1BE]
ACPI: Lid Switch [C136]
ibm_acpi: ec object not found
ACPI: Video Device [C0D0] (multi-head: yes rom: no post: no)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda2, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
NTFS driver 2.1.27 [Flags: R/W MODULE].
NTFS volume version 3.1.
NTFS-fs error (device sda1): load_system_files(): Volume is dirty.
Mounting read-only. Run chkdsk and mount in Windows.
SELinux: initialized (dev sda1, type ntfs), uses genfs_contexts
Adding 1048568k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1
across:1048568k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses
genfs_contexts
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (4094 buckets, 32752 max) - 224 bytes per conntrack
eth0: link down
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
Bluetooth: Core ver 2.8
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: link down
ADDRCONF(NETDEV_UP): eth0: link is not ready
eth1: NETDEV_TX_BUSY returned; driver should report queue full via
ieee_device->is_queue_full.
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [C0C2] -> GSI 10 (level,
low) -> IRQ 10
[drm] Initialized radeon 1.24.0 20060225 on minor 0
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
[drm] Setting GART location based on new memory map
[drm] Loading R200 Microcode
[drm] writeback test succeeded in 1 usecs
ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
ieee80211_crypt: registered algorithm 'CCMP'
eth1: no IPv6 routers present
usb 4-2: new high speed USB device using ehci_hcd and address 2
usb 4-2: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
Vendor: Kingston Model: DT Elite HS 2.0 Rev: 5.02
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sdb: 2052607 512-byte hdwr sectors (1051 MB)
sdb: Write Protect is off
sdb: Mode Sense: 45 00 00 08
sdb: assuming drive cache: write through
SCSI device sdb: 2052607 512-byte hdwr sectors (1051 MB)
sdb: Write Protect is off
sdb: Mode Sense: 45 00 00 08
sdb: assuming drive cache: write through
sdb: sdb1
sd 2:0:0:0: Attached scsi removable disk sdb
sd 2:0:0:0: Attached scsi generic sg2 type 0
usb-storage: device scan complete
SELinux: initialized (dev sdb1, type vfat), uses genfs_contexts
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/