Re: 2.6.18-rc1-mm1

[Reuben Farrelly]

On 10/07/2006 12:56 a.m., Alan Cox wrote:
> Ar Sul, 2006-07-09 am 05:22 -0700, ysgrifennodd Andrew Morton:
> > > ata5: PATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0x30B0 irq 14
> > > scsi4 : ata_piix
> > > ata5.00: ATAPI, max UDMA/66
> > > ata5.00: configured for UDMA/66
>
> More ATAPI devices getting uppity about mode setting.
>
> > John stuff.  I suspect it's natural and normal, if the IDE error handling
> > did something rude with interrupt holdoff.
>
> The new libata should be more polite than that, although since the ATA
> drive can stall the CPU indefinitely you lose anyway 8(

It may not be related to ATA.  I just reloaded into 2.6.17-mm6 to get the info 
for Alan and saw it when booting up on that too:

PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
Losing some ticks... checking if CPU frequency changed.
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7

Note it was in a different place in here than in -rc1-mm1 (slightly later in the 
bootup).

I'm fairly sure it's not new to this release.

> > > Jul  2 12:03:28 tornado kernel: hda: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 
> > > 2000kB Cache, UDMA(66)
>
> Can you send me the full hdparm identify stuff for this ?

sh-3.1# hdparm -I /dev/hda

/dev/hda:

ATAPI CD-ROM, with removable media
        Model Number:       PIONEER DVD-RW  DVR-111D
        Serial Number:      FADC005671WL
        Firmware Revision:  1.23
Standards:
        Likely used CD-ROM ATAPI-1
Configuration:
        DRQ response: 50us.
        Packet size: 12 bytes
Capabilities:
        LBA, IORDY(can be disabled)
        Buffer size: 64.0kB
        DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4
             Cycle time: min=120ns recommended=120ns
        PIO: pio0 pio1 pio2 pio3 pio4
             Cycle time: no flow control=240ns  IORDY flow control=120ns
Commands/features:
        Enabled Supported:
           *    Power Management feature set
           *    PACKET command feature set
           *    DEVICE_RESET command
HW reset results:
        CBLID- above Vih
        Device num = 0 determined by the jumper
sh-3.1#
sh-3.1# hdparm -i /dev/hda

/dev/hda:

 Model=PIONEER DVD-RW DVR-111D, FwRev=1.23, SerialNo=
 Config={ Fixed Removeable DTR<=5Mbs DTR>10Mbs nonMagnetic }
 RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0
 BuffType=13395, BuffSize=64kB, MaxMultSect=0
 (maybe): CurCHS=0/0/0, CurSects=0, LBA=yes, LBAsects=0
 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4
 DMA modes:  mdma0 mdma1 mdma2
 UDMA modes: udma0 udma1 udma2 udma3 *udma4
 AdvancedPM=no
 Drive conforms to: Unspecified:  ATA/ATAPI-2 ATA/ATAPI-3 ATA/ATAPI-4 ATA/ATAPI-5

 * signifies the current active mode

sh-3.1#


Reuben
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/