Re: [patch] PM: suspend/resume debugging should depend onSOFTWARE_SUSPEND

[Mike Galbraith]

On Fri, 2006-11-24 at 10:08 -0800, Linus Torvalds wrote:
> 
> On Fri, 24 Nov 2006, Mike Galbraith wrote:
> > 
> > I tried the dynticks/hires-timers/kbd suggestion, no difference.  It
> > still boots in medicated snail mode, and emits a stream of IRQ9: nobody
> > cared messages (fasteoi acpi, irqpoll = nogo) while doing so.
> 
> "medicated snail mode". Lol.

It turns out, that this is caused by console=ttyS0,115200n8.  Without
the problematic driver found by pm_trace for the old Pinacle SAT card...

02:02.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
	Subsystem: Pinnacle Systems Inc. PCTV Sat (DBC receiver)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (4000ns min, 10000ns max)
	Interrupt: pin A routed to IRQ 17
	Region 0: Memory at f2100000 (32-bit, prefetchable) [size=4K]
	Capabilities: [44] Vital Product Data
	Capabilities: [4c] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

went boom here -->02:02.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
	Subsystem: Pinnacle Systems Inc. PCTV Sat (DBC receiver)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (1000ns min, 63750ns max)
	Interrupt: pin A routed to IRQ 17
	Region 0: Memory at f2101000 (32-bit, prefetchable) [size=4K]
	Capabilities: [44] Vital Product Data
	Capabilities: [4c] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:03.0 Multimedia controller: Philips Semiconductors SAA7134 Video Broadcast Decoder (rev 01)
	Subsystem: Creatix Polymedia GmbH Medion 7134
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (2000ns min, 8000ns max)
	Interrupt: pin A routed to IRQ 20
	Region 0: Memory at f2002000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: [40] Power Management version 1
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=1 PME-

...and the serial console, I can now suspend to ram just fine with stock
2.6.19-rc6.  As a serial port test, I set up a getty on ttyS0, and
logged in via minicom prior to suspend.  After resume, the serial port
isn't talking.  Kill -9 the shell though, and all is fine again.

> Based on the "fasteoi", you're obviously right now using the APIC, and 
> that's _usually_ the mode that works better. But just in case, try booting 
> with "noapic".

Makes no difference for vanilla, works just fine either way, I don't
even have to remove vga=0x314. The RT kernel has some issues in this
area with s2ram, but that's a different story.

	Hope you're having/had a nice weekend, and thanks for the tips!

	-Mike

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/