Re: 2.6.18 - AHCI detection pauses excessively
From: Berck E. Nash
Date: Mon Nov 27 2006 - 03:58:42 EST
Tejun Heo wrote:
Yeah, I did and forgot about this thread too. Sorry. This is on the
top of my to-do list now. I'm attaching the patch. TIA.
That didn't fix the problem, but did change the messages. I've attached
the entire log, including the weird errors on power-off from the same
device that gives problems on boot, which I suspect are related.
Berck
[ 0.000000] Linux version 2.6.19-rc6-mm1 (root@luna) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-20)) #3 SMP PREEMPT Sun Nov 26 21:25:59 MST 2006
[ 0.000000] Command line: root=/dev/sdc1 ro console=tty0 console=ttyS0,115200n8 BOOT_IMAGE=vmlinuz
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003ff80000 (usable)
[ 0.000000] BIOS-e820: 000000003ff80000 - 000000003ff8e000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003ff8e000 - 000000003ffe0000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003ffe0000 - 0000000040000000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
[ 0.000000] end_pfn_map = 1048576
[ 0.000000] DMI 2.4 present.
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] DMA32 4096 -> 1048576
[ 0.000000] Normal 1048576 -> 1048576
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0 -> 159
[ 0.000000] 0: 256 -> 262016
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 (Bootup-CPU)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] Processor #1
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] Setting APIC routing to flat
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Nosave address range: 000000000009f000 - 00000000000a0000
[ 0.000000] Nosave address range: 00000000000a0000 - 00000000000e4000
[ 0.000000] Nosave address range: 00000000000e4000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:bfb00000)
[ 0.000000] PERCPU: Allocating 32512 bytes of per cpu data
[ 0.000000] Built 1 zonelists. Total pages: 257375
[ 0.000000] Kernel command line: root=/dev/sdc1 ro console=tty0 console=ttyS0,115200n8 BOOT_IMAGE=vmlinuz
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 57.369381] Console: colour VGA+ 80x25
[ 57.632610] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 57.639997] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 57.646956] Checking aperture...
[ 57.657752] Memory: 1027700k/1048064k available (2281k kernel code, 19860k reserved, 999k data, 196k init)
[ 57.726521] Calibrating delay using timer specific routine.. 5800.15 BogoMIPS (lpj=2900075)
[ 57.734992] Mount-cache hash table entries: 256
[ 57.739636] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 57.744433] CPU: L2 cache: 2048K
[ 57.747699] using mwait in idle threads.
[ 57.751657] CPU: Physical Processor ID: 0
[ 57.755701] CPU: Processor Core ID: 0
[ 57.759400] CPU0: Thermal monitoring enabled (TM2)
[ 57.764238] Freeing SMP alternatives: 24k freed
[ 57.768811] ACPI: Core revision 20060707
[ 57.797724] Using local APIC timer interrupts.
[ 57.836680] result 25877185
[ 57.839512] Detected 25.877 MHz APIC timer.
[ 57.844463] Booting processor 1/2 APIC 0x1
[ 57.858937] Initializing CPU#1
[ 57.919341] Calibrating delay using timer specific routine.. 5796.44 BogoMIPS (lpj=2898222)
[ 57.919345] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 57.919346] CPU: L2 cache: 2048K
[ 57.919348] CPU: Physical Processor ID: 0
[ 57.919348] CPU: Processor Core ID: 1
[ 57.919352] CPU1: Thermal monitoring enabled (TM2)
[ 57.919543] Intel(R) Core(TM)2 CPU 6300 @ 1.86GHz stepping 06
[ 57.920346] Brought up 2 CPUs
[ 57.962055] testing NMI watchdog ... OK.
[ 57.996481] time.c: Using 14.318180 MHz WALL HPET GTOD HPET/TSC timer.
[ 58.003041] time.c: Detected 2898.247 MHz processor.
[ 58.095698] migration_cost=22
[ 58.099005] NET: Registered protocol family 16
[ 58.103489] wait_for_probes: waiting for 0 threads
[ 58.108353] wait_for_probes: waiting for 0 threads
[ 58.113184] ACPI: bus type pci registered
[ 58.117236] PCI: BIOS Bug: MCFG area at f0000000 is not E820-reserved
[ 58.123713] PCI: Not using MMCONFIG.
[ 58.127328] PCI: Using configuration type 1
[ 58.131544] wait_for_probes: waiting for 0 threads
[ 58.144443] ACPI: Interpreter enabled
[ 58.148145] ACPI: Using IOAPIC for interrupt routing
[ 58.153867] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 58.159174] PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
[ 58.165654] PCI quirk: region 0480-04bf claimed by ICH6 GPIO
[ 58.171805] PCI: Transparent bridge - 0000:00:1e.0
[ 58.183676] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 58.191454] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 *7 10 11 12 14 15)
[ 58.199230] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15)
[ 58.207003] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 58.214779] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 58.222892] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 58.230668] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 58.238444] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 58.246113] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 58.251804] pnp: PnP ACPI init
[ 58.257367] pnp: PnP ACPI: found 15 devices
[ 58.261613] intel_rng: FWH not detected
[ 58.265571] SCSI subsystem initialized
[ 58.269400] PCI: Using ACPI for IRQ routing
[ 58.273619] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 58.281970] wait_for_probes: waiting for 0 threads
[ 58.286792] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 58.291874] hpet0: 3 64-bit timers, 14318180 Hz
[ 58.297442] PCI-GART: No AMD northbridge found.
[ 58.302523] pnp: 00:07: ioport range 0x290-0x297 has been reserved
[ 58.308910] PCI: Bridge: 0000:00:01.0
[ 58.312610] IO window: disabled.
[ 58.316047] MEM window: faa00000-feafffff
[ 58.320263] PREFETCH window: cff00000-efefffff
[ 58.324915] PCI: Bridge: 0000:00:1c.0
[ 58.328610] IO window: disabled.
[ 58.332050] MEM window: disabled.
[ 58.335573] PREFETCH window: cfe00000-cfefffff
[ 58.340226] PCI: Bridge: 0000:00:1c.3
[ 58.343919] IO window: c000-cfff
[ 58.347359] MEM window: fa900000-fa9fffff
[ 58.351575] PREFETCH window: disabled.
[ 58.355533] PCI: Bridge: 0000:00:1e.0
[ 58.359229] IO window: b000-bfff
[ 58.362668] MEM window: fa700000-fa8fffff
[ 58.366885] PREFETCH window: 50000000-500fffff
[ 58.371541] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 58.379035] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 58.386523] ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19
[ 58.394027] NET: Registered protocol family 2
[ 58.410079] IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 58.417339] TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
[ 58.425423] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 58.432657] TCP: Hash tables configured (established 131072 bind 65536)
[ 58.439300] TCP reno registered
[ 58.446108] wait_for_probes: waiting for 0 threads
[ 58.451398] audit: initializing netlink socket (disabled)
[ 58.456838] audit(1164581690.592:1): initialized
[ 58.466875] Loading Reiser4. See www.namesys.com for a description of Reiser4.
[ 58.474192] io scheduler noop registered
[ 58.478542] io scheduler anticipatory registered (default)
[ 58.484336] assign_interrupt_mode Found MSI capability
[ 58.489590] assign_interrupt_mode Found MSI capability
[ 58.494852] assign_interrupt_mode Found MSI capability
[ 58.500163] input: Power Button (FF) as /class/input/input0
[ 58.505766] ACPI: Power Button (FF) [PWRF]
[ 58.509935] input: Power Button (CM) as /class/input/input1
[ 58.515541] ACPI: Power Button (CM) [PWRB]
[ 58.519974] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 58.526417] ACPI: Processor [CPU2] (supports 8 throttling states)
[ 58.532636] ACPI: Getting cpuindex for acpiid 0x3
[ 58.537377] ACPI: Getting cpuindex for acpiid 0x4
[ 58.543441] Real Time Clock Driver v1.12ac
[ 58.547651] Linux agpgart interface v0.101 (c) Dave Jones
[ 58.553087] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
[ 58.561039] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 58.567369] 00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 58.573106] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 58.579491] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 58.587557] ICH7: IDE controller at PCI slot 0000:00:1f.1
[ 58.592994] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 22 (level, low) -> IRQ 22
[ 58.600476] ICH7: chipset revision 1
[ 58.604083] ICH7: not 100% native mode: will probe irqs later
[ 58.609868] ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
[ 58.617226] ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio<7>Losing some ticks... checking if CPU frequency changed.
[ 58.629616]
[ 59.303006] hda: LITE-ON LTR-48246S, ATAPI CD/DVD-ROM drive
[ 60.022548] hdb: _NEC DVD_RW ND-3520AW, ATAPI CD/DVD-ROM drive
[ 60.082411] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 60.605720] SiI680: IDE controller at PCI slot 0000:01:00.0
[ 60.611332] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 21 (level, low) -> IRQ 21
[ 60.618815] SiI680: chipset revision 2
[ 60.622608] SiI680: BASE CLOCK == 133
[ 60.626351] SiI680: 100% native mode on irq 21
[ 60.630835] ide2: MMIO-DMA , BIOS settings: hde:pio, hdf:pio
[ 60.636968] ide3: MMIO-DMA , BIOS settings: hdg:pio, hdh:pio
[ 60.908838] hde: SAMSUNG WN316025A (1.6 GB), ATA DISK drive
[ 61.525676] ide2 at 0xffffc20000006c80-0xffffc20000006c87,0xffffc20000006c8a on irq 21
[ 61.797585] hdg: MAXTOR 6L040J2, ATA DISK drive
[ 62.413451] ide3 at 0xffffc20000006cc0-0xffffc20000006cc7,0xffffc20000006cca on irq 21
[ 62.421565] hde: max request size: 64KiB
[ 62.425521] hde: 3145968 sectors (1610 MB) w/109KiB Cache, CHS=3121/16/63, DMA
[ 62.432984] hde: hde1
[ 62.448439] hdg: max request size: 64KiB
[ 62.453350] hdg: 78198750 sectors (40037 MB) w/1819KiB Cache, CHS=65535/16/63, UDMA(133)
[ 62.461826] hdg: cache flushes supported
[ 62.465792] hdg: hdg1
[ 62.484633] hda: ATAPI 48X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
[ 62.491607] Uniform CD-ROM driver Revision: 3.20
[ 62.535733] hdb: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
[ 62.556615] ACPI: PCI Interrupt 0000:01:01.0[A] -> GSI 22 (level, low) -> IRQ 22
[ 62.564736] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 23 (level, low) -> IRQ 23
[ 62.572472] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 62.578688] PNP: PS/2 controller doesn't have AUX irq; using default 12
[ 62.587929] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 62.592943] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 62.598095] mice: PS/2 mouse device common for all mice
[ 62.603362] EDAC MC: Ver: 2.0.1 Nov 25 2006
[ 62.607686] TCP cubic registered
[ 62.610950] Initializing XFRM netlink socket
[ 62.615263] NET: Registered protocol family 1
[ 62.619657] NET: Registered protocol family 17
[ 62.624147] NET: Registered protocol family 15
[ 62.628628] wait_for_probes: waiting for 3 threads
[ 62.636844] input: AT Translated Set 2 keyboard as /class/input/input2
[ 62.773700] scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
[ 62.773701] <Adaptec 2940 Ultra2 SCSI adapter>
[ 62.773702] aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs
[ 62.773702]
[ 63.054114] scsi 0:0:1:0: Direct-Access IBM-PCCO ST39102LC !# B219 PQ: 0 ANSI: 2
[ 63.062248] scsi0:A:1:0: Tagged Queuing enabled. Depth 8
[ 63.067731] target0:0:1: Beginning Domain Validation
[ 63.079230] target0:0:1: wide asynchronous
[ 63.088137] target0:0:1: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 15)
[ 63.099356] target0:0:1: Domain Validation skipping write tests
[ 63.105399] target0:0:1: Ending Domain Validation
[ 63.113209] scsi 0:0:2:0: Direct-Access SGI SEAGATE ST39102L 2702 PQ: 0 ANSI: 2
[ 63.121334] scsi0:A:2:0: Tagged Queuing enabled. Depth 8
[ 63.126818] target0:0:2: Beginning Domain Validation
[ 63.137168] target0:0:2: wide asynchronous
[ 63.145241] target0:0:2: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 15)
[ 63.155644] target0:0:2: Domain Validation skipping write tests
[ 63.161682] target0:0:2: Ending Domain Validation
[ 63.577105] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
[ 63.585232] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part
[ 63.592092] ata1: SATA max UDMA/133 cmd 0xFFFFC2000000E900 ctl 0x0 bmdma 0x0 irq 316
[ 63.599913] ata2: SATA max UDMA/133 cmd 0xFFFFC2000000E980 ctl 0x0 bmdma 0x0 irq 316
[ 63.607731] ata3: SATA max UDMA/133 cmd 0xFFFFC2000000EA00 ctl 0x0 bmdma 0x0 irq 316
[ 63.615549] ata4: SATA max UDMA/133 cmd 0xFFFFC2000000EA80 ctl 0x0 bmdma 0x0 irq 316
[ 63.623332] scsi1 : ahci
[ 63.927590] SATA PHY: stable DET=3
[ 64.031995] SATA PHY: stable DET=3
[ 64.136570] SATA PHY: stable DET=3
[ 64.241067] SATA PHY: stable DET=3
[ 64.344525] SATA PHY: stable DET=3
[ 64.449101] SATA PHY: stable DET=3
[ 64.553506] SATA PHY: stable DET=3
[ 64.658081] SATA PHY: stable DET=3
[ 64.762552] SATA PHY: stable DET=3
[ 64.866036] SATA PHY: stable DET=3
[ 64.970612] SATA PHY: stable DET=3
[ 65.075017] SATA PHY: stable DET=3
[ 65.179592] SATA PHY: stable DET=3
[ 65.284037] SATA PHY: stable DET=3
[ 65.387534] SATA PHY: stable DET=3
[ 65.492109] SATA PHY: stable DET=3
[ 65.596515] SATA PHY: stable DET=3
[ 65.701089] SATA PHY: stable DET=3
[ 65.805534] SATA PHY: stable DET=3
[ 65.909045] SATA PHY: stable DET=3
[ 65.912479] SATA PHY: debounced
[ 66.070326] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 66.083463] ata1.00: ATA-6, max UDMA/133, 72303840 sectors: LBA48
[ 66.089681] ata1.00: ata1: dev 0 multi count 16
[ 66.102173] ata1.00: configured for UDMA/133
[ 66.106487] scsi2 : ahci
[ 66.240954] SCSI device sda: 17774160 512-byte hdwr sectors (9100 MB)
[ 66.249392] sda: Write Protect is off
[ 66.254682] SCSI device sda: write cache: enabled, read cache: enabled, supports DPO and FUA
[ 66.263935] SCSI device sda: 17774160 512-byte hdwr sectors (9100 MB)
[ 66.272374] sda: Write Protect is off
[ 66.277646] SCSI device sda: write cache: enabled, read cache: enabled, supports DPO and FUA
[ 66.286123] sda: sda1 sda2
[ 66.295437] sd 0:0:1:0: Attached scsi disk sda
[ 66.299945] sd 0:0:1:0: Attached scsi generic sg0 type 0
[ 66.306160] SCSI device sdb: 17781520 512-byte hdwr sectors (9104 MB)
[ 66.316003] sdb: Write Protect is off
[ 66.323489] SCSI device sdb: write cache: enabled, read cache: enabled, supports DPO and FUA
[ 66.332780] SCSI device sdb: 17781520 512-byte hdwr sectors (9104 MB)
[ 66.342624] sdb: Write Protect is off
[ 66.350085] SCSI device sdb: write cache: enabled, read cache: enabled, supports DPO and FUA
[ 66.358564] sdb: sdb1
[ 66.367085] sd 0:0:2:0: Attached scsi disk sdb
[ 66.371597] sd 0:0:2:0: Attached scsi generic sg1 type 0
[ 66.413576] SATA PHY: stable DET=3
[ 66.518137] SATA PHY: stable DET=3
[ 66.622543] SATA PHY: stable DET=3
[ 66.727118] SATA PHY: stable DET=3
[ 66.831523] SATA PHY: stable DET=3
[ 66.936098] SATA PHY: stable DET=3
[ 67.040660] SATA PHY: stable DET=3
[ 67.145065] SATA PHY: stable DET=3
[ 67.249640] SATA PHY: stable DET=3
[ 67.354046] SATA PHY: stable DET=3
[ 67.458621] SATA PHY: stable DET=3
[ 67.563183] SATA PHY: stable DET=3
[ 67.667589] SATA PHY: stable DET=3
[ 67.772164] SATA PHY: stable DET=3
[ 67.876570] SATA PHY: stable DET=3
[ 67.981144] SATA PHY: stable DET=3
[ 68.085707] SATA PHY: stable DET=3
[ 68.190099] SATA PHY: stable DET=3
[ 68.294674] SATA PHY: stable DET=3
[ 68.404075] SATA PHY: stable DET=3
[ 68.407512] SATA PHY: debounced
[ 68.565486] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 98.544548] ata2.00: qc timeout (cmd 0xec)
[ 98.548679] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x104)
[ 99.358514] SATA PHY: stable DET=3
[ 99.463089] SATA PHY: stable DET=3
[ 99.567495] SATA PHY: stable DET=3
[ 99.672070] SATA PHY: stable DET=3
[ 99.776515] SATA PHY: stable DET=3
[ 99.880026] SATA PHY: stable DET=3
[ 99.984601] SATA PHY: stable DET=3
[ 100.089006] SATA PHY: stable DET=3
[ 100.193581] SATA PHY: stable DET=3
[ 100.298013] SATA PHY: stable DET=3
[ 100.401537] SATA PHY: stable DET=3
[ 100.506112] SATA PHY: stable DET=3
[ 100.610517] SATA PHY: stable DET=3
[ 100.715092] SATA PHY: stable DET=3
[ 100.819511] SATA PHY: stable DET=3
[ 100.924060] SATA PHY: stable DET=3
[ 101.028635] SATA PHY: stable DET=3
[ 101.133040] SATA PHY: stable DET=3
[ 101.237615] SATA PHY: stable DET=3
[ 101.342034] SATA PHY: stable DET=3
[ 101.345474] SATA PHY: debounced
[ 108.385331] ata2: port is slow to respond, please be patient (Status 0x80)
[ 131.326177] ata2: port failed to respond (30 secs, Status 0x80)
[ 131.332131] ata2: COMRESET failed (device not ready)
[ 131.337127] ata2: hardreset failed, retrying in 5 secs
[ 136.642653] SATA PHY: stable DET=3
[ 136.747228] SATA PHY: stable DET=3
[ 136.851699] SATA PHY: stable DET=3
[ 136.955170] SATA PHY: stable DET=3
[ 137.059746] SATA PHY: stable DET=3
[ 137.164151] SATA PHY: stable DET=3
[ 137.268726] SATA PHY: stable DET=3
[ 137.373184] SATA PHY: stable DET=3
[ 137.476682] SATA PHY: stable DET=3
[ 137.581257] SATA PHY: stable DET=3
[ 137.685662] SATA PHY: stable DET=3
[ 137.790237] SATA PHY: stable DET=3
[ 137.894682] SATA PHY: stable DET=3
[ 137.998193] SATA PHY: stable DET=3
[ 138.102768] SATA PHY: stable DET=3
[ 138.207173] SATA PHY: stable DET=3
[ 138.311748] SATA PHY: stable DET=3
[ 138.416180] SATA PHY: stable DET=3
[ 138.519704] SATA PHY: stable DET=3
[ 138.624279] SATA PHY: stable DET=3
[ 138.627716] SATA PHY: debounced
[ 138.630908] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 138.641746] ata2.00: ATA-6, max UDMA/133, 640 sectors: LBA
[ 138.647349] ata2.00: ata2: dev 0 multi count 1
[ 138.656446] ata2.00: configured for UDMA/133
[ 138.660753] scsi3 : ahci
[ 138.964628] SATA PHY: stable DET=3
[ 139.069190] SATA PHY: stable DET=3
[ 139.173752] SATA PHY: stable DET=3
[ 139.278157] SATA PHY: stable DET=3
[ 139.382733] SATA PHY: stable DET=3
[ 139.487138] SATA PHY: stable DET=3
[ 139.591713] SATA PHY: stable DET=3
[ 139.696275] SATA PHY: stable DET=3
[ 139.800681] SATA PHY: stable DET=3
[ 139.905256] SATA PHY: stable DET=3
[ 140.009661] SATA PHY: stable DET=3
[ 140.114237] SATA PHY: stable DET=3
[ 140.218799] SATA PHY: stable DET=3
[ 140.323204] SATA PHY: stable DET=3
[ 140.427779] SATA PHY: stable DET=3
[ 140.532185] SATA PHY: stable DET=3
[ 140.636760] SATA PHY: stable DET=3
[ 140.741322] SATA PHY: stable DET=3
[ 140.845727] SATA PHY: stable DET=3
[ 140.950302] SATA PHY: stable DET=3
[ 140.953737] SATA PHY: debounced
[ 141.111543] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 141.123065] ata3.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 31/32)
[ 141.130844] ata3.00: ata3: dev 0 multi count 16
[ 141.140769] ata3.00: configured for UDMA/133
[ 141.145078] scsi4 : ahci
[ 141.449052] SATA PHY: stable DET=0
[ 141.553626] SATA PHY: stable DET=0
[ 141.658032] SATA PHY: stable DET=0
[ 141.762607] SATA PHY: stable DET=0
[ 141.867052] SATA PHY: stable DET=0
[ 141.970563] SATA PHY: stable DET=0
[ 142.075138] SATA PHY: stable DET=0
[ 142.179543] SATA PHY: stable DET=0
[ 142.284118] SATA PHY: stable DET=0
[ 142.388550] SATA PHY: stable DET=0
[ 142.492074] SATA PHY: stable DET=0
[ 142.596649] SATA PHY: stable DET=0
[ 142.701048] SATA PHY: stable DET=0
[ 142.805617] SATA PHY: stable DET=0
[ 142.910022] SATA PHY: stable DET=0
[ 143.014584] SATA PHY: stable DET=0
[ 143.119146] SATA PHY: stable DET=0
[ 143.223552] SATA PHY: stable DET=0
[ 143.328127] SATA PHY: stable DET=0
[ 143.432532] SATA PHY: stable DET=0
[ 143.435965] SATA PHY: debounced
[ 143.439146] ata4: SATA link down (SStatus 0 SControl 300)
[ 143.444617] scsi 1:0:0:0: Direct-Access ATA WDC WD360GD-00FL 31.0 PQ: 0 ANSI: 5
[ 143.452786] SCSI device sdc: 72303840 512-byte hdwr sectors (37020 MB)
[ 143.459353] sdc: Write Protect is off
[ 143.463061] SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 143.472081] SCSI device sdc: 72303840 512-byte hdwr sectors (37020 MB)
[ 143.478649] sdc: Write Protect is off
[ 143.482352] SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 143.491347] sdc: sdc1 sdc2
[ 143.502458] sd 1:0:0:0: Attached scsi disk sdc
[ 143.506968] sd 1:0:0:0: Attached scsi generic sg2 type 0
[ 143.512352] scsi 2:0:0:0: Direct-Access ATA Config Disk RGL1 PQ: 0 ANSI: 5
[ 143.520525] SCSI device sdd: 640 512-byte hdwr sectors (0 MB)
[ 143.526313] sdd: Write Protect is off
[ 143.530021] SCSI device sdd: write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 143.539123] SCSI device sdd: 640 512-byte hdwr sectors (0 MB)
[ 143.544915] sdd: Write Protect is off
[ 143.548618] SCSI device sdd: write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 143.557700] sdd: unknown partition table
[ 143.561965] sd 2:0:0:0: Attached scsi disk sdd
[ 143.566471] sd 2:0:0:0: Attached scsi generic sg3 type 0
[ 143.571856] scsi 3:0:0:0: Direct-Access ATA ST3250823AS 3.03 PQ: 0 ANSI: 5
[ 143.580033] SCSI device sde: 488397168 512-byte hdwr sectors (250059 MB)
[ 143.586770] sde: Write Protect is off
[ 143.590476] SCSI device sde: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 143.599487] SCSI device sde: 488397168 512-byte hdwr sectors (250059 MB)
[ 143.606226] sde: Write Protect is off
[ 143.609938] SCSI device sde: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 143.618935] sde: sde1 sde2
[ 143.628705] sd 3:0:0:0: Attached scsi disk sde
[ 143.633214] sd 3:0:0:0: Attached scsi generic sg4 type 0
[ 143.638621] wait_for_probes: waiting for 0 threads
[ 143.644027] reiser4: sdc1: found disk format 4.0.0.
[ 144.852704] VFS: Mounted root (reiser4 filesystem) readonly.
[ 144.858424] Freeing unused kernel memory: 196k freed
INIT: version 2.86 booting
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...[ 147.094500] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 147.102175] sky2 v1.10 addr 0xfa9fc000 irq 19 Yukon-EC (0xb6) rev 2
[ 147.108722] sky2 eth0: addr 00:18:f3:3d:1b:06
[ 147.113659] Floppy drive(s): fd0 is 1.44M
[ 147.132226] FDC 0 is a post-1991 82077
[ 147.140641] usbcore: registered new interface driver usbfs
[ 147.146253] usbcore: registr4en1ew interface driver hub
[ 147.151727] usbcore: registered new device driver usb
[ 147.176300] ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 23 (level, low) -> IRQ 23
[ 147.194214] USB Universal Host Controller Interface driver v3.0
[ 147.200314] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 20
[ 147.205440] ACPI: PCI Interrupt 000070:1d.1[B] -> GSI 17 (level, low) -> IRQ 17
[ 147.205450] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 147.205525] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 1
[ 147.2054P] uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000e800
[ 147.206118] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 147.206126] uhci_hcd 0000:00:1d.2: UHCI Hosodnraoeir
[ 147.206158] usb usb1: new device found, idVendor=0000, idProduct=0000
[ 147.206159] usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
[ 147.206161] usb usb1: Product: UHCI Host ContrlUer
[ 147.206162] usb usb1: Manufacturer: Linux 2.6.19-rc6-mm1 uhci_hcd
[ 147.206163] usb usb1: SerialNumber: 0000:00:1d.1
[ 147.206204] usb usb1: configuration #1 chosen fro 21 choice
[ 147.206218] hub 1-0:1.0: USB hub found
[ 147.206221] hub 1-0:1.0: 2 ports detected
[ 147.206233] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 2
[ 147.206261] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e880
[ 147.206292] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 19
[ 147.206299] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 147.206320] usb usb2: new device found, idVendor=0000, idProduct=0000
[ 147.206322] usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
[ 147.206323] usb usb2: Product: UHCI Host Controller
[ 147.206324] usb usb2: Manufacturer: Linux 2.6.19-rc6-mm1 uhci_hcd
[ 147.206326] usb usb2: SerialNumber: 0000:00:1d.2
[ 147.206354] usb usb2: configuration #1 chosen from 1 choice
[ 147.206367] hub 2-0:1.0: USB hub found
[ 147.206370] hub 2-0:1.0: 2 ports detected
[ 147.206382] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 3
[ 147.206408] uhci_hcd 0000:00:1d.3: irq 19, io base 0x0000ec00
[ 147.206446] usb usb3: new device found, idVendor=0000, idProduct=0000
[ 147.206447] usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
[ 147.206448] usb usb3: Product: UHCI Host Controller
[ 147.206450] usb usb3: Manufacturer: Linux 2.6.19-rc6-mm1 uhci_hcd
[ 147.206451] usb usb3: SerialNumber: 0000:00:1d.3
[ 147.206477] usb usb3: configuration #1 chosen from 1 choice
[ 147.206489] hub 3-0:1.0: USB hub found
[ 147.206492] hub 3-0:1.0: 2 ports detected
[ 147.421598] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 147.427070] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4
[ 147.434751] uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000e480
[ 147.440796] usb usb4: new device found, idVendor=0000, idProduct=0000
[ 147.448538] usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
[ 147.455593] usb usb4: Product: UHCI Host Controller
[ 147.460591] usb usb4: Manufacturer: Linux 2.6.19-rc6-mm1 uhci_hcd
[ 147.469255] usb usb4: SerialNumber: 0000:00:1d.0
[ 147.474562] usb usb4: configuration #1 chosen from 1 choice
[ 147.480258] hub 4-0:1.0: USB hub found
[ 147.484115] hub 4-0:1.0: 2 ports detected
[ 147.517639] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 20
[ 147.525681] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 147.531082] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[ 147.538724] ehci_hcd 0000:00:1d.7: debug port 1
[ 147.543386] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xfebfbc00
[ 147.553056] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 147.560798] usb usb5: new device found, idVendor=0000, idProduct=0000
[ 147.567356] usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
[ 147.574394] usb usb5: Product: EHCI Host Controller
[ 147.579382] usb usb5: Manufacturer: Linux 2.6.19-rc6-mm1 ehci_hcd
[ 147.585609] usb usb5: SerialNumber: 0000:00:1d.7
[ 147.590675] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 147.598091] usb usb5: configuration #1 chosen from 1 choice
[ 147.598111] hub 5-0:1.0: USB hub found
[ 147.598115] hub 5-0:1.0: 8 ports detected
[ 147.664579] hda_codec: Unknown model for ALC882, trying auto-probe from BIOS...
done.
Setting parameters of disc: (none).
Activating swap:swapon on /dev/sdc2
[ 148.501685] Adding 1959920k swap on /dev/sdc2. Priority:-1 extents:1 across:1959920k
.
Will now check root file system:fsck 1.40-WIP (14-Nov-2006)
[/sbin/fsck.reiser4 (1) -- /] fsck.reiser4 -a /dev/sdc1
fsck.reiser4 /dev/sdc1
.
Setting the system clock again..
[ 148.846087] usb 5-7: new high speed USB device using ehci_hcd and address 6
[ 148.971198] usb 5-7: new device found, idVendor=05e3, idProduct=0606
[ 148.977871] usb 5-7: new device strings: Mfr=0, Product=1, SerialNumber=0
[ 148.985141] usb 5-7: Product: USB2.0 Hub
[ 148.989440] usb 5-7: configuration #1 chosen from 1 choice
[ 148.995552] hub 5-7:1.0: USB hub found
[ 148.999907] hub 5-7:1.0: 4 ports detected
[ 149.179768] usb 4-1: new low speed USB device using uhci_hcd and address 2
[ 149.359046] usb 4-1: new device found, idVendor=045e, idProduct=001e
[ 149.365905] usb 4-1: new device strings: Mfr=1, Product=2, SerialNumber=0
[ 149.373212] usb 4-1: Product: Microsoft IntelliMouse® Explorer
[ 149.379456] usb 4-1: Manufacturer: Microsoft
[ 149.384122] usb 4-1: configuration #1 chosen from 1 choice
System Clock set. Local time: Sun Nov 26 22:56:23 MST 2006.
Cleaning up ifupdown....
Loading kernel module nvidia.
[ 149.527299] usb 4-2: new low speed USB device using uhci_hcd and address 3
[ 149.664808] usbcore: registered new interface driver hiddev
[ 149.691745] usb 4-2: new device found, idVendor=0d3d, idProduct=0001
[ 149.698254] usb 4-2: new device strings: Mfr=0, Product=2, SerialNumber=0
[ 149.705179] usb 4-2: Product: USBPS2
[ 149.708899] usb 4-2: configuration #1 chosen from 1 choice
[ 149.870517] usb 2-1: new full speed USB device using uhci_hcd and address 3
[ 149.990442] usb 2-1: device descriptor read/64, error -71
[ 150.209320] usb 2-1: device descriptor read/64, error -71
[ 150.257283] nvidia: module license 'NVIDIA' taints kernel.
[ 150.416927] usb 2-1: new full speed USB device using uhci_hcd and address 4
[ 150.515873] NVRM: The NVIDIA probe routine was not called for 1 device(s).
[ 150.515890] ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 150.530441] NVRM: This can occur when a driver such as rivafb, nvidiafb or
[ 150.530442] NVRM: rivatv was loaded and obtained ownership of the NVIDIA
[ 150.530443] NVRM: device(s).
[ 150.536819] usb 2-1: device descriptor read/64, error -71
[ 150.552801] NVRM: Try unloading the rivafb, nvidiafb or rivatv kernel module
[ 150.552802] NVRM: (and/or reconfigure your kernel without rivafb/nvidiafb
[ 150.552803] NVRM: support), then try loading the NVIDIA kernel module again.
[ 150.574122] NVRM: loading NVIDIA Linux x86_64 Kernel Module 1.0-9629 Wed Nov 1 19:27:33 PST 2006
Loading kernel module loop.
FATAL: Module loop not found.
Loading kernel module i2c-i801.
Loading kernel module i2c-isa.
Loading kernel module eeprom.
Loading kernel module w83627ehf.
Loading kernel module usb-storage.
[ 150.655320] Initializing USB Mass Storage driver...
[ 150.752226] usb 2-1: device descriptor read/64, error -71
[ 150.961220] usb 2-1: new full speed USB device using uhci_hcd and address 5
[ 151.376260] usb 2-1: device not accepting address 5, error -71
[ 151.484845] usb 2-1: new full speed USB device using uhci_hcd and address 6
[ 151.899912] usb 2-1: device not accepting address 6, error -71
[ 152.112034] usb 2-2: new full speed USB device using uhci_hcd and address 7
[ 152.419953] usb 5-7.3: new high speed USB device using ehci_hcd and address 7
[ 152.511368] usb 5-7.3: new device found, idVendor=0bda, idProduct=8187
[ 152.518346] usb 5-7.3: new device strings: Mfr=1, Product=2, SerialNumber=3
[ 152.525398] usb 5-7.3: Product: RTL8187_Wireless
[ 152.530085] usb 5-7.3: Manufacturer: Manufacturer_Realtek_RTL8187_
[ 152.531240] input: Microsoft Microsoft IntelliMouse® Explorer as /class/input/input3
[ 152.531376] input: USB HID v1.00 Mouse [Microsoft Microsoft IntelliMouse® Explorer] on usb-0000:00:1d.0-1
[ 152.553989] usb 5-7.3: SerialNumber: 0015AF05C9DE
[ 152.558883] usb 5-7.3: configuration #1 chosen from 1 choice
[ 152.564748] input: USBPS2 as /class/input/input4
[ 152.569559] input: USB HID v1.00 Keyboard [USBPS2] on usb-0000:00:1d.0-2
[ 152.598228] input: USBPS2 as /class/input/input5
[ 152.603008] input: USB HID v1.00 Mouse [USBPS2] on usb-0000:00:1d.0-2
[ 152.609682] usbcore: registered new interface driver usbhid
[ 152.612079] usbcore: registered new interface driver usb-storage
[ 152.612081] USB Mass Storage support registered.
[ 152.626231] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Loading kernel module snd-rtctimer.
Loading kernel module uhci-hcd.
Loading kernel module acpi-cpufreq.
FATAL: Error inserting acpi_cpuf[ 152.674231] usbcore: registered new interface driver cdc_acm
req (/lib/module[ 152.680227] drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model driver for USB modems and ISDN adapters
s/2.6.19-rc6-mm1/kernel/arch/x86_64/kernel/cpufreq/acpi-cpufreq.ko): No such device
Loading kernel module cdc-acm.
Loading device-mapper support.
Will now check all file systems.
fsck 1.40-WIP (14-Nov-2006)
Checking all file systems.
Done checking file systems.
A log is being saved in /var/log/fsck/checkfs if that location is writable.
Setting kernel variables...done.
Will now mount local filesystems:[ 152.853692] ReiserFS: sde1: found reiserfs format "3.6" with standard journal
[ 152.860994] ReiserFS: sde1: using ordered data mode
[ 152.875751] ReiserFS: sde1: journal params: device sde1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 152.890838] ReiserFS: sde1: checking transaction log (sde1)
[ 152.968048] ReiserFS: sde1: Using r5 hash to sort names
[ 153.035606] reiser4: sda1: found disk format 4.0.0.
.
Will now activate swapfile swap:done.
Cleaning /tmp...done.
Cleaning /var/run...done.
Cleaning /var/lock...done.
Setting up networking....
Configuring network interfaces...done.
Starting portmap daemon....
[ 154.803119] sky2 eth0: enabling interface
Setting sensors limits: done.
Setting console screen modes and fonts.
Setting up ALSA...done.
Initializing random number generator...done.
Recovering nvi editor sessions...none found.
Setting up X server socket directory /tmp/.X11-unix....
Setting up ICE socket directory /tmp/.ICE-unix....
Recovering schroot sessions... done.
INIT: Entering runlevel: 2
Starting system log daemon....
Starting kernel log daemon....
Loading ACPI modules:
Starting Advanced Configuration and Power Interface daemon: acpid.
Starting Common Unix Printing System: cupsd[ 157.299194] usb 2-2: new device found, idVendor=03f0, idProduct=0401
[ 157.305711] usb 2-2: new device strings: Mfr=1, Product=2, SerialNumber=3
[ 157.312652] usb 2-2: Product: HP ScanJet 5200C
[ 157.317694] sky2 eth0: Link is up at 1000 Mbps, full duplex, flow control both
[ 157.325090] usb 2-2: Manufacturer: Hewlett-Packard
[ 157.329976] usb 2-2: SerialNumber: SG91U161Z2HT
[ 157.334680] usb 2-2: configuration #1 chosen from 1 choice
.
Starting system message bus: dbus.
Starting Hardware abstraction layer: hald.
Starting DirMngr: dirmngr.
Starting mouse interface server: gpm.
Starting internet superserver: inetd.
Starting Postfix Mail Transport Agent: postfix.
Starting Samba daemons: nmbd smbd.
Starting sensor daemon: sensord.
Starting OpenBSD Secure Shell server: sshd.
Setting up X font server socket directory /tmp/.font-unix...done.
Starting X font server: xfs.
Starting NFS common utilities: statd.
Starting NTP server: ntpd.
Starting deferred execution scheduler: atd.
Starting periodic command scheduler: crond.
Starting K Display Manager: kdm.
Running local boot scripts (/etc/rc.local).
Debian GNU/Linux 4.0 luna ttyS0
luna login: INIT:Stopping K Display Manager: kdm.
Stopping deferred execution scheduler: atd.
Stopping periodic command scheduler: crond.
Stopping Samba daemons: nmbd smbd.
Stopping Advanced Configuration and Power Interface daemon: acpid.
Stopping Common Unix Printing System: cupsd.
Stopping Hardware abstraction layer: hald.
Stopping system message bus: dbus.
Stopping DirMngr: dirmngr.
Stopping mouse interface server: gpm.
Stopping internet superserver: inetd.
Stopping Postfix Mail Transport Agent: postfix.
Stopping sensor daemon: sensord.
Stopping OpenBSD Secure Shell server: sshd.
Stopping X font server: xfs.
Stopping NTP server: ntpd.
Saving the system clock..
Hardware Clock updated to Mon Nov 27 01:30:01 MST 2006.
Shutting down ALSA...done.
Stopping NFS common utilities: statd.
Stopping kernel log daemon....
Stopping system log daemon....
Saving random seed...done.
Asking non-system processes to terminate...done.
Unmounting remote and non-toplevel virtual filesystems...done.
Stopping portmap daemon....
Deconfiguring network interfaces...[ 9363.903564] sky2 eth0: disabling interface
done.
Cleaning up ifupdown....
Asking all remaining processes to terminate...done.
Killing all remaining processes...done.
Will now unmount temporary filesystems:/dev umounted
.
Will now deactivate swap:swapoff on /dev/sdc2
.
Will now unmount local filesystems:/backup umounted
/home umounted
/tmp umounted
/dev/sde1 umounted
/dev/sda1 umounted
/dev/hde1 umounted
.
Mounting root filesystem read-only...done.
Will now halt.
[ 9371.896444] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9371.903036] ata2.00: (irq_stat 0x40000001)
[ 9371.907228] ata2.00: cmd e0/00:00:00:00:00/00:00:00:00:00/00 tag 0 data 0 in
[ 9371.907229] res 51/04:00:01:01:80/00:00:00:00:00/a0 Emask 0x1 (device error)
[ 9371.931688] ata2.00: configured for UDMA/133
[ 9371.936073] ata2: EH complete
[ 9371.939137] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9371.945702] ata2.00: (irq_stat 0x40000001)
[ 9371.949899] ata2.00: cmd e0/00:00:00:00:00/00:00:00:00:00/00 tag 0 data 0 in
[ 9371.949900] res 51/04:00:01:01:80/00:00:00:00:00/a0 Emask 0x1 (device error)
[ 9371.974319] ata2.00: configured for UDMA/133
[ 9371.978701] ata2: EH complete
[ 9371.981763] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9371.988346] ata2.00: (irq_stat 0x40000001)
[ 9371.992543] ata2.00: cmd e0/00:00:00:00:00/00:00:00:00:00/00 tag 0 data 0 in
[ 9371.992544] res 51/04:00:01:01:80/00:00:00:00:00/a0 Emask 0x1 (device error)
[ 9372.016961] ata2.00: configured for UDMA/133
[ 9372.021345] ata2: EH complete
[ 9372.024417] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9372.030990] ata2.00: (irq_stat 0x40000001)
[ 9372.035190] ata2.00: cmd e0/00:00:00:00:00/00:00:00:00:00/00 tag 0 data 0 in
[ 9372.035191] res 51/04:00:01:01:80/00:00:00:00:00/a0 Emask 0x1 (device error)
[ 9372.059604] ata2.00: configured for UDMA/133
[ 9372.063981] ata2: EH complete
[ 9372.067053] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9372.073634] ata2.00: (irq_stat 0x40000001)
[ 9372.077834] ata2.00: cmd e0/00:00:00:00:00/00:00:00:00:00/00 tag 0 data 0 in
[ 9372.077835] res 51/04:00:01:01:80/00:00:00:00:00/a0 Emask 0x1 (device error)
[ 9372.102259] ata2.00: configured for UDMA/133
[ 9372.106633] ata2: EH complete
[ 9372.109702] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9372.116280] ata2.00: (irq_stat 0x40000001)
[ 9372.120471] ata2.00: cmd e0/00:00:00:00:00/00:00:00:00:00/00 tag 0 data 0 in
[ 9372.120472] res 51/04:00:01:01:80/00:00:00:00:00/a0 Emask 0x1 (device error)
[ 9372.144866] ata2.00: configured for UDMA/133
[ 9372.149237] ata2: EH complete
[ 9372.152310] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9372.158882] ata2.00: (irq_stat 0x40000001)
[ 9372.163079] ata2.00: cmd 94/00:00:00:00:00/00:00:00:00:00/00 tag 0 data 0 in
[ 9372.163080] res 51/04:00:01:01:80/00:00:00:00:00/a0 Emask 0x1 (device error)
[ 9372.187505] ata2.00: configured for UDMA/133
[ 9372.191891] ata2: EH complete
[ 9372.194954] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9372.201528] ata2.00: (irq_stat 0x40000001)
[ 9372.205725] ata2.00: cmd 94/00:00:00:00:00/00:00:00:00:00/00 tag 0 data 0 in
[ 9372.205726] res 51/04:00:01:01:80/00:00:00:00:00/a0 Emask 0x1 (device error)
[ 9372.230150] ata2.00: configured for UDMA/133
[ 9372.234525] ata2: EH complete
[ 9372.237590] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9372.244171] ata2.00: (irq_stat 0x40000001)
[ 9372.248370] ata2.00: cmd 94/00:00:00:00:00/00:00:00:00:00/00 tag 0 data 0 in
[ 9372.248371] res 51/04:00:01:01:80/00:00:00:00:00/a0 Emask 0x1 (device error)
[ 9372.272791] ata2.00: configured for UDMA/133
[ 9372.277161] ata2: EH complete
[ 9372.280236] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9372.286818] ata2.00: (irq_stat 0x40000001)
[ 9372.291015] ata2.00: cmd 94/00:00:00:00:00/00:00:00:00:00/00 tag 0 data 0 in
[ 9372.291016] res 51/04:00:01:01:80/00:00:00:00:00/a0 Emask 0x1 (device error)
[ 9372.315408] ata2.00: configured for UDMA/133
[ 9372.319772] ata2: EH complete
[ 9372.322838] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9372.329410] ata2.00: (irq_stat 0x40000001)
[ 9372.333607] ata2.00: cmd 94/00:00:00:00:00/00:00:00:00:00/00 tag 0 data 0 in
[ 9372.333608] res 51/04:00:01:01:80/00:00:00:00:00/a0 Emask 0x1 (device error)
[ 9372.358023] ata2.00: configured for UDMA/133
[ 9372.362390] ata2: EH complete
[ 9372.365463] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9372.372036] ata2.00: (irq_stat 0x40000001)
[ 9372.376236] ata2.00: cmd 94/00:00:00:00:00/00:00:00:00:00/00 tag 0 data 0 in
[ 9372.376237] res 51/04:00:01:01:80/00:00:00:00:00/a0 Emask 0x1 (device error)
[ 9372.400648] ata2.00: configured for UDMA/133
[ 9372.405018] ata2: EH complete
[ 9372.408077] SCSI device sdd: 640 512-byte hdwr sectors (0 MB)
[ 9372.410277] Synchronizing SCSI cache for disk sde:
[ 9372.418928] sdd: Write Protect is off
[ 9372.422679] SCSI device sdd: write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 9372.431950] SCSI device sdd: 640 512-byte hdwr sectors (0 MB)
[ 9372.437839] sdd: Write Protect is off
[ 9372.441609] SCSI device sdd: write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 9372.450324] Synchronizing SCSI cache for disk sdc:
[ 9372.450480] Synchronizing SCSI cache for disk sdb:
[ 9372.450732] Synchronizing SCSI cache for disk sda:
[ 9372.942537] Shutdown: hdg
[ 9372.945441] Shutdown: hde
[ 9372.948690] Power down.
[ 9372.951278] acpi_power_off called