Re: regression with gammu on 2.6.21-rc7

[Greg KH]

On Mon, Apr 23, 2007 at 10:10:22AM +0200, Wolfgang Erig wrote:
> Hello Greg,

Please don't take me out of the cc:, otherwise I might mist this (as I
did...)

> On Sun, Apr 22, 2007 at 10:47:17PM -0700, Greg KH wrote:
> > On Fri, Apr 20, 2007 at 10:58:53AM +0200, Wolfgang Erig wrote:
> > > Hello,
> > > 
> > > I have a regression with 2.6.21-rc7-g80d74d51.
> > > The utility "gammu" to talk to my mobile does not work anymore.
> > > With 2.6.20 gammu runs fine.
> > > 
> > > Distribution is the latest Debian/testing
> > > 
> > > Wolfgang
> > > 
> > > $ gammu --backup backup
> > > Press Ctrl+C to break...
> > > I/O possible
> the problem is here because gammu stops working.
> Maybe a problem in gammu, but with 2.6.20 gammu works fine.
> > > $ uname -a
> > > Linux max 2.6.21-rc7-g80d74d51 #9 SMP Wed Apr 18 21:41:41 CEST 2007 i686 GNU/Linux
> > > $ tail messages 
> > > Apr 20 08:04:36 max kernel: ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 16
> > > Apr 20 08:04:36 max kernel: extern: link up, 100Mbps, full-duplex, lpa 0x45E1
> > > Apr 20 08:04:36 max kernel: intern:  setting half-duplex.
> > > Apr 20 08:09:02 max kernel: usb 2-2: USB disconnect, address 3
> > > Apr 20 08:09:02 max kernel: pl2303 ttyUSB0: pl2303 converter now disconnected from ttyUSB0
> > > Apr 20 08:09:02 max kernel: pl2303 2-2:1.0: device disconnected
> > > Apr 20 08:10:24 max kernel: usb 2-2: new full speed USB device using uhci_hcd and address 4
> > > Apr 20 08:10:25 max kernel: usb 2-2: configuration #1 chosen from 1 choice
> > > Apr 20 08:10:25 max kernel: pl2303 2-2:1.0: pl2303 converter detected
> > > Apr 20 08:10:25 max kernel: usb 2-2: pl2303 converter now attached to ttyUSB0
> > 
> > That looks ok, I'm guessing you yanked it out and then back in?
> Yes.
> This is included only to see which device is connected.
> > Or is the problem that the device was removed?
> No, no problem with removal.
> I see no hint for a problem in the usb-layer.

I don't see any problems here.

If you enable debugging in the pl2303 driver, do you get any errors?
You can do this by:
	modprobe pl2303 debug=1
or if the module is built in or already loaded:
	echo 1 > /sys/modules/pl2303/parameters/debug


Also, if you know how to use git, doing a 'git bisect' to try to track
down the problem commit would be very helpful.

thanks,

greg k-h
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/