Re: Linux 2.6.21 - something wrong with dmesg.
From: Sunil Naidu
Date: Thu Apr 26 2007 - 08:15:01 EST
Hello,
I did compile the kernel, boots good ;-) BTW, does anyone (on P-III)
facing a memory check skip or sort of? Not getting RAM info in the
dmesg. Unable to get dmseg from the start of the gcc check! Any clue?
Here is the dmesg I get on my box:
00000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 6:11 APIC version 17
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 20000000 (gap:
1ff00000:e00c0000)
[ 0.000000] Built 1 zonelists. Total pages: 129779
[ 0.000000] Kernel command line: ro root=LABEL=/
[ 0.000000] mapped APIC to ffffd000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffc000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] Detected 1202.764 MHz processor.
[ 13.595214] Console: colour VGA+ 80x25
[ 13.601724] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 13.603679] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 13.646235] Memory: 513268k/523200k available (2175k kernel code,
9388k reserved, 733k data, 212k init, 0k highmem)
[ 13.646415] virtual kernel memory layout:
[ 13.646417] fixmap : 0xfffb7000 - 0xfffff000 ( 288 kB)
[ 13.646420] vmalloc : 0xe0800000 - 0xfffb5000 ( 503 MB)
[ 13.646422] lowmem : 0xc0000000 - 0xdfef0000 ( 510 MB)
[ 13.646425] .init : 0xc03da000 - 0xc040f000 ( 212 kB)
[ 13.646427] .data : 0xc031fdd5 - 0xc03d7514 ( 733 kB)
[ 13.646430] .text : 0xc0100000 - 0xc031fdd5 (2175 kB)
[ 13.647089] Checking if this processor honours the WP bit even in
supervisor mode... Ok.
[ 13.707417] Calibrating delay using timer specific routine..
2406.24 BogoMIPS (lpj=1203121)
[ 13.707685] Security Framework v1.0.0 initialized
[ 13.707797] SELinux: Initializing.
[ 13.707914] SELinux: Starting in permissive mode
[ 13.707924] selinux_register_security: Registering secondary
module capability
[ 13.708082] Capability LSM initialized as secondary
[ 13.708200] Mount-cache hash table entries: 512
[ 13.708547] CPU: After generic identify, caps: 0383fbff 00000000
00000000 00000000 00000000 00000000 00000000
[ 13.708568] CPU: L1 I cache: 16K, L1 D cache: 16K
[ 13.708695] CPU: L2 cache: 256K
[ 13.708785] CPU: After all inits, caps: 0383fbff 00000000 00000000
00000040 00000000 00000000 00000000
[ 13.708795] Intel machine check architecture supported.
[ 13.708892] Intel machine check reporting enabled on CPU#0.
[ 13.709007] CPU: Intel(R) Pentium(R) III CPU 1200MHz stepping 01
[ 13.709165] Checking 'hlt' instruction... OK.
[ 13.712650] ACPI: Core revision 20070126
[ 13.716326] ENABLING IO-APIC IRQs
[ 13.716655] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 13.828786] NET: Registered protocol family 16
[ 13.829173] ACPI: bus type pci registered
[ 13.830908] PCI: PCI BIOS revision 2.10 entry at 0xfdb81, last bus=1
[ 13.831014] PCI: Using configuration type 1
[ 13.831112] Setting up standard PCI resources
[ 13.838325] ACPI: Interpreter enabled
[ 13.838440] ACPI: (supports S0 S1 S4 S5)
[ 13.838691] ACPI: Using IOAPIC for interrupt routing
[ 13.848472] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 13.848617] PCI: Probing PCI hardware (bus 00)
[ 13.848796] Boot video device is 0000:00:01.0
[ 13.848901] PCI quirk: region 0400-047f claimed by ICH4 ACPI/GPIO/TCO
[ 13.849009] PCI quirk: region 0480-04bf claimed by ICH4 GPIO
[ 13.849601] PCI: Transparent bridge - 0000:00:1e.0
[ 13.849744] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 13.849943] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.ICHB._PRT]
[ 13.865597] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11 *12 14 15)
[ 13.866208] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 13.866795] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 13.867378] ACPI: PCI Interrupt Link [LNKD] (IRQs 9) *11
[ 13.867640] ACPI Error (psargs-0355): [PRSE] Namespace lookup
failure, AE_NOT_FOUND
[ 13.867849] ACPI Error (psparse-0537): Method parse/execution
failed [\_SB_.LNKE._PRS] (Node dfd61f40), AE_NOT_FOUND
[ 13.868118] ACPI Exception (pci_link-0179): AE_NOT_FOUND,
Evaluating _PRS [20070126]
[ 13.868407] ACPI Error (psargs-0355): [PRSF] Namespace lookup
failure, AE_NOT_FOUND
[ 13.868635] ACPI Error (psparse-0537): Method parse/execution
failed [\_SB_.LNKF._PRS] (Node dfd61ea0), AE_NOT_FOUND
[ 13.868913] ACPI Exception (pci_link-0179): AE_NOT_FOUND,
Evaluating _PRS [20070126]
[ 13.869193] ACPI Error (psargs-0355): [PRSG] Namespace lookup
failure, AE_NOT_FOUND
[ 13.869421] ACPI Error (psparse-0537): Method parse/execution
failed [\_SB_.LNKG._PRS] (Node dfd61e00), AE_NOT_FOUND
[ 13.869704] ACPI Exception (pci_link-0179): AE_NOT_FOUND,
Evaluating _PRS [20070126]
[ 13.869980] ACPI Error (psargs-0355): [PRSH] Namespace lookup
failure, AE_NOT_FOUND
[ 13.870201] ACPI Error (psparse-0537): Method parse/execution
failed [\_SB_.LNKH._PRS] (Node c147b75c), AE_NOT_FOUND
[ 13.870484] ACPI Exception (pci_link-0179): AE_NOT_FOUND,
Evaluating _PRS [20070126]
[ 13.870928] ACPI: Power Resource [URP1] (off)
[ 13.871079] ACPI: Power Resource [URP2] (off)
[ 13.871228] ACPI: Power Resource [FDDP] (off)
[ 13.871380] ACPI: Power Resource [LPTP] (off)
[ 13.871502] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 13.871621] pnp: PnP ACPI init
[ 13.877725] pnp: PnP ACPI: found 12 devices
[ 13.878121] usbcore: registered new interface driver usbfs
[ 13.878293] usbcore: registered new interface driver hub
[ 13.878493] usbcore: registered new device driver usb
[ 13.878640] PCI: Using ACPI for IRQ routing
[ 13.878739] PCI: If a device doesn't work, try "pci=routeirq". If
it helps, post a report
[ 13.881330] NetLabel: Initializing
[ 13.881419] NetLabel: domain hash size = 128
[ 13.881508] NetLabel: protocols = UNLABELED CIPSOv4
[ 13.881622] NetLabel: unlabeled traffic allowed by default
[ 13.882333] Time: tsc clocksource has been installed.
[ 13.912288] PCI: Ignore bogus resource 6 [0:0] of 0000:00:01.0
[ 13.912400] PCI: Bridge: 0000:00:1e.0
[ 13.912497] IO window: c000-cfff
[ 13.912599] MEM window: efd00000-efdfffff
[ 13.912699] PREFETCH window: e7b00000-e7bfffff
[ 13.912809] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 13.912873] NET: Registered protocol family 2
[ 13.922378] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 13.922633] TCP established hash table entries: 16384 (order: 5,
131072 bytes)
[ 13.923353] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 13.923709] TCP: Hash tables configured (established 16384 bind 16384)
[ 13.923806] TCP reno registered
[ 13.926723] checking if image is initramfs... it is
[ 14.132575] Freeing initrd memory: 1476k freed
[ 14.133959] audit: initializing netlink socket (disabled)
[ 14.134114] audit(1177607993.133:1): initialized
[ 14.134526] VFS: Disk quotas dquot_6.5.1
[ 14.134650] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 14.134886] SELinux: Registering netfilter hooks
[ 14.135007] io scheduler noop registered
[ 14.135134] io scheduler cfq registered (default)
[ 14.136312] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 14.136674] isapnp: Scanning for PnP cards...
[ 14.411954] Switched to NOHz mode on CPU #0
[ 14.493091] isapnp: No Plug & Play device found
[ 14.498494] Real Time Clock Driver v1.12ac
[ 14.498930] Non-volatile memory driver v1.2
[ 14.499032] Linux agpgart interface v0.102 (c) Dave Jones
[ 14.499305] agpgart: Detected an Intel i810 E Chipset.
[ 14.511472] agpgart: AGP aperture is 64M @ 0xe8000000
[ 14.511662] [drm] Initialized drm 1.1.0 20060810
[ 14.511760] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports,
IRQ sharing enabled
[ 14.512089] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 14.512374] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 14.513183] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 14.514625] RAMDISK driver initialized: 16 RAM disks of 16384K size
4096 blocksize
[ 14.515060] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 14.515219] ide: Assuming 33MHz system bus speed for PIO modes;
override with idebus=xx
[ 14.515486] ICH2: IDE controller at PCI slot 0000:00:1f.1
[ 14.516930] ICH2: chipset revision 5
[ 14.517027] ICH2: not 100% native mode: will probe irqs later
[ 14.517149] ide0: BM-DMA at 0xff00-0xff07, BIOS settings:
hda:DMA, hdb:pio
[ 14.517385] ide1: BM-DMA at 0xff08-0xff0f, BIOS settings:
hdc:DMA, hdd:pio
[ 14.517612] Probing IDE interface ide0...
[ 14.781149] hda: ST310212A, ATA DISK drive
[ 15.393499] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 15.393813] Probing IDE interface ide1...
[ 16.064782] hdc: SONY CD-RW CRX320E, ATAPI CD/DVD-ROM drive
[ 16.676993] ide1 at 0x170-0x177,0x376 on irq 15
[ 16.677547] hda: max request size: 128KiB
[ 16.678611] hda: 20005650 sectors (10242 MB) w/512KiB Cache,
CHS=19846/16/63, UDMA(66)
[ 16.678883] hda: cache flushes not supported
[ 16.679055] hda: hda1 hda2 hda3
[ 16.710139] usbcore: registered new interface driver libusual
[ 16.710309] usbcore: registered new interface driver hiddev
[ 16.710458] usbcore: registered new interface driver usbhid
[ 16.710574] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[ 16.710811] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 16.710915] PNP: PS/2 controller doesn't have AUX irq; using default 12
[ 16.961686] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 16.962006] mice: PS/2 mouse device common for all mice
[ 16.962441] TCP cubic registered
[ 16.962542] Initializing XFRM netlink socket
[ 16.962679] NET: Registered protocol family 1
[ 16.962784] NET: Registered protocol family 17
[ 16.962897] Using IPI Shortcut mode
[ 16.963912] Freeing unused kernel memory: 212k freed
[ 16.987600] input: AT Translated Set 2 keyboard as /class/input/input0
[ 17.239843] USB Universal Host Controller Interface driver v3.0
[ 17.240103] ACPI: PCI Interrupt 0000:00:1f.2[D] -> GSI 19 (level,
low) -> IRQ 16
[ 17.240357] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 17.240364] uhci_hcd 0000:00:1f.2: UHCI Host Controller
[ 17.240614] uhci_hcd 0000:00:1f.2: new USB bus registered, assigned
bus number 1
[ 17.240819] uhci_hcd 0000:00:1f.2: irq 16, io base 0x0000dd80
[ 17.241204] usb usb1: configuration #1 chosen from 1 choice
[ 17.241370] hub 1-0:1.0: USB hub found
[ 17.241480] hub 1-0:1.0: 2 ports detected
[ 17.345406] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller
(OHCI) Driver
[ 17.345495] ACPI: PCI Interrupt 0000:01:04.0[B] -> GSI 17 (level,
low) -> IRQ 17
[ 17.345701] ohci_hcd 0000:01:04.0: OHCI Host Controller
[ 17.345840] ohci_hcd 0000:01:04.0: new USB bus registered, assigned
bus number 2
[ 17.346034] ohci_hcd 0000:01:04.0: irq 17, io mem 0xefdfd000
[ 17.398519] usb usb2: configuration #1 chosen from 1 choice
[ 17.398696] hub 2-0:1.0: USB hub found
[ 17.398802] hub 2-0:1.0: 2 ports detected
[ 17.499488] ACPI: PCI Interrupt 0000:01:04.1[C] -> GSI 18 (level,
low) -> IRQ 18
[ 17.499698] ohci_hcd 0000:01:04.1: OHCI Host Controller
[ 17.499845] ohci_hcd 0000:01:04.1: new USB bus registered, assigned
bus number 3
[ 17.500030] ohci_hcd 0000:01:04.1: irq 18, io mem 0xefdfe000
[ 17.552402] usb usb3: configuration #1 chosen from 1 choice
[ 17.552566] hub 3-0:1.0: USB hub found
[ 17.552678] hub 3-0:1.0: 2 ports detected
[ 17.657372] ACPI: PCI Interrupt 0000:01:04.3[A] -> GSI 16 (level,
low) -> IRQ 19
[ 17.657602] ehci_hcd 0000:01:04.3: EHCI Host Controller
[ 17.657801] ehci_hcd 0000:01:04.3: new USB bus registered, assigned
bus number 4
[ 17.658002] ehci_hcd 0000:01:04.3: debug port 1
[ 17.678219] ehci_hcd 0000:01:04.3: irq 19, io mem 0xefdffe00
[ 17.678325] ehci_hcd 0000:01:04.3: USB 2.0 started, EHCI 1.00,
driver 10 Dec 2004
[ 17.678756] usb usb4: configuration #1 chosen from 1 choice
[ 17.678942] hub 4-0:1.0: USB hub found
[ 17.679056] hub 4-0:1.0: 6 ports detected
[ 17.971021] SCSI subsystem initialized
[ 17.990351] libata version 2.20 loaded.
[ 18.228227] kjournald starting. Commit interval 5 seconds
[ 18.228358] EXT3-fs: mounted filesystem with ordered data mode.
[ 18.469980] usb 3-1: new low speed USB device using ohci_hcd and address 2
[ 18.645969] usb 3-1: configuration #1 chosen from 1 choice
[ 18.665259] input: Microsoft Basic Optical Mouse as /class/input/input1
[ 18.665421] input: USB HID v1.10 Mouse [Microsoft Basic Optical
Mouse] on usb-0000:01:04.1-1
[ 18.881856] usb 3-2: new full speed USB device using ohci_hcd and address 3
[ 19.076688] usb 3-2: configuration #1 chosen from 1 choice
[ 21.360931] SELinux: Disabled at runtime.
[ 21.361053] SELinux: Unregistering netfilter hooks
[ 21.366160] audit(1177608000.132:2): selinux=0 auid=4294967295
[ 26.507431] parport: PnPBIOS parport detected.
[ 26.507465] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP(,...)]
[ 26.655780] hdc: ATAPI 40X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
[ 26.655803] Uniform CD-ROM driver Revision: 3.20
[ 27.222552] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
[ 27.222658] ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 17 (level,
low) -> IRQ 17
[ 27.259075] eth0: VIA Rhine III at 0xefdfff00, 00:15:e9:48:b1:a4, IRQ 17.
[ 27.259796] eth0: MII PHY found at address 1, status 0x786d
advertising 01e1 Link 0021.
[ 27.448739] input: PC Speaker as /class/input/input2
[ 27.465215] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
[ 27.465326] iTCO_wdt: failed to reset NO_REBOOT flag, reboot
disabled by hardware
[ 27.465336] iTCO_wdt: No card detected
[ 27.543127] intel_rng: FWH not detected
[ 27.829884] i810_smbus 0000:00:01.0: i810/i815 i2c device found.
[ 27.920141] Floppy drive(s): fd0 is 1.44M
[ 27.936834] FDC 0 is a post-1991 82077
[ 28.232248] ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level,
low) -> IRQ 17
[ 28.232298] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[ 28.545156] intel8x0_measure_ac97_clock: measured 50920 usecs
[ 28.545165] intel8x0: clocking to 48000
[ 30.430914] lp0: using parport0 (interrupt-driven).
[ 30.753854] input: Power Button (FF) as /class/input/input3
[ 30.772105] ACPI: Power Button (FF) [PWRF]
[ 30.790110] input: Power Button (CM) as /class/input/input4
[ 30.808898] ACPI: Power Button (CM) [PWRB]
[ 30.827050] input: Sleep Button (CM) as /class/input/input5
[ 30.845283] ACPI: Sleep Button (CM) [SLPB]
[ 31.534526] EXT3 FS on hda3, internal journal
[ 31.925279] fuse init (API version 7.8)
[ 33.216055] Adding 265032k swap on /dev/hda2. Priority:-1
extents:1 across:265032k
[ 34.875622] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 35.522114] Netfilter messages via NETLINK v0.30.
[ 35.541789] nf_conntrack version 0.5.0 (4087 buckets, 32696 max)
[ 38.582733] eth0: link up, 10Mbps, half-duplex, lpa 0x0021
[ 40.907876] audit(1177588220.592:3): audit_pid=1676 old=0 by auid=4294967295
~Akula2
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/