Re: [PATCH 1/2] Eliminate references to new_client in i2cdocumentation

[Jean Delvare]

Hi Grant,

On Thu, 10 May 2007 15:04:16 -0600, Grant Likely wrote:
> The use of 'new_client' in i2c device allocation has been refered to as
> a 'disease'.  Replace all occurances of 'struct i2c_client *new_client'
> in documentation examples with 'struct i2c_client *client'.
> 
> Also remove unnecessary zero initializtion of .flags since kzalloc is used.
> 
> Signed-off-by: Grant Likely <grant.likely@xxxxxxxxxxxx>

Thanks for your contribution, however I made a similar documentation
cleanup 3 weeks ago:
  http://lists.lm-sensors.org/pipermail/i2c/2007-April/001075.html
It's upstream already.

> ---
> 
>  Documentation/i2c/writing-clients |   29 ++++++++++++++---------------
>  1 files changed, 14 insertions(+), 15 deletions(-)
> 
> diff --git a/Documentation/i2c/writing-clients b/Documentation/i2c/writing-clients
> index fbcff96..bd61480 100644
> --- a/Documentation/i2c/writing-clients
> +++ b/Documentation/i2c/writing-clients
> @@ -260,7 +260,7 @@ For now, you can ignore the `flags' parameter. It is there for future use.
>    {
>      int err = 0;
>      int i;
> -    struct i2c_client *new_client;
> +    struct i2c_client *client;
>      struct foo_data *data;
>      const char *client_name = ""; /* For non-`sensors' drivers, put the real
>                                       name here! */
> @@ -323,13 +323,12 @@ For now, you can ignore the `flags' parameter. It is there for future use.
>        goto ERROR0;
>      }
>  
> -    new_client = &data->client;
> -    i2c_set_clientdata(new_client, data);
> +    client = &data->client;
> +    i2c_set_clientdata(client, data);
>  
> -    new_client->addr = address;
> -    new_client->adapter = adapter;
> -    new_client->driver = &foo_driver;
> -    new_client->flags = 0;
> +    client->addr = address;
> +    client->adapter = adapter;
> +    client->driver = &foo_driver;
>  
>      /* Now, we do the remaining detection. If no `force' parameter is used. */
>  
> @@ -337,7 +336,7 @@ For now, you can ignore the `flags' parameter. It is there for future use.
>         parameter was used. */
>      if (kind < 0) {
>        /* The below is of course bogus */
> -      if (foo_read(new_client,FOO_REG_GENERIC) != FOO_GENERIC_VALUE)
> +      if (foo_read(client,FOO_REG_GENERIC) != FOO_GENERIC_VALUE)
>           goto ERROR1;
>      }
>  
> @@ -349,7 +348,7 @@ For now, you can ignore the `flags' parameter. It is there for future use.
>      /* Determine the chip type. Not needed if a `force_CHIPTYPE' parameter
>         was used. */
>      if (kind <= 0) {
> -      i = foo_read(new_client,FOO_REG_CHIPTYPE);
> +      i = foo_read(client,FOO_REG_CHIPTYPE);
>        if (i == FOO_TYPE_1) 
>          kind = chip1; /* As defined in the enum */
>        else if (i == FOO_TYPE_2)
> @@ -377,7 +376,7 @@ For now, you can ignore the `flags' parameter. It is there for future use.
>      /* SENSORS ONLY END */
>  
>      /* Fill in the remaining client fields. */
> -    strcpy(new_client->name,client_name);
> +    strcpy(client->name,client_name);
>  
>      /* SENSORS ONLY BEGIN */
>      data->type = kind;
> @@ -389,14 +388,14 @@ For now, you can ignore the `flags' parameter. It is there for future use.
>      /* Any other initializations in data must be done here too. */
>  
>      /* Tell the i2c layer a new client has arrived */
> -    if ((err = i2c_attach_client(new_client)))
> +    if ((err = i2c_attach_client(client)))
>        goto ERROR3;
>  
>      /* SENSORS ONLY BEGIN */
>      /* Register a new directory entry with module sensors. See below for
>         the `template' structure. */
> -    if ((i = i2c_register_entry(new_client, type_name,
> -                                    foo_dir_table_template,THIS_MODULE)) < 0) {
> +    if ((i = i2c_register_entry(client, type_name,
> +                                foo_dir_table_template,THIS_MODULE)) < 0) {
>        err = i;
>        goto ERROR4;
>      }
> @@ -406,14 +405,14 @@ For now, you can ignore the `flags' parameter. It is there for future use.
>  
>      /* This function can write default values to the client registers, if
>         needed. */
> -    foo_init_client(new_client);
> +    foo_init_client(client);
>      return 0;
>  
>      /* OK, this is not exactly good programming practice, usually. But it is
>         very code-efficient in this case. */
>  
>      ERROR4:
> -      i2c_detach_client(new_client);
> +      i2c_detach_client(client);
>      ERROR3:
>      ERROR2:
>      /* SENSORS ONLY START */


-- 
Jean Delvare
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/