Re: 2.6.22-rc: regression: no irda0 interface (2.6.21 was OK), smsc does not find chip
From: Andrey Borzenkov
Date: Mon Jun 11 2007 - 10:05:13 EST
On Monday 11 June 2007, Bjorn Helgaas wrote:
> > {pts/1}% lspnp -vv 00:0a
> > 00:0a SMCf010 SMC Fast Infrared Port
> > state = active
> > allocated resources:
> > io 0x100-0x107
> > ...
> >
> > {pts/1}% cat /proc/ioports
> > ...
> > 0100-013f : pcmcia_socket0
> > ...
> >
> > {pts/1}% sudo cat
> > /sys/class/pcmcia_socket/pcmcia_socket0/available_resources_io 0x00000100
> > - 0x000003af
> > 0x000003e0 - 0x000004ff
> > 0x00000820 - 0x000008ff
> > 0x00000a00 - 0x00000aff
> > 0x00000c00 - 0x00000cf7
>
> It's indeed very interesting that pcmcia_socket0 seems to have its
> fingers in the same ioport range the IR device thinks it's using.
> I don't know much about PCMCIA, but I can see I'm going to have to
> learn something :-)
>
For the record - I tried to completely unload PCMCIA driver for slot 0 (and
verified that 0x100 IO port is free) and tried to load smsc, but it did not
change anything whether I used first or second port for FIR.
> Can you send me your "lspci -vv" output, the whole /proc/ioports and
> /proc/iomem, and your dmesg log? And maybe your pcmcia_socket
> available_resources_io and available_resources_mem for good measure.
>
Sure.
lspci:
00:00.0 Host bridge: ALi Corporation M1644/M1644T Northbridge+Trident (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ >SERR- <PERR+
Latency: 0
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [b0] AGP version 2.0
Status: RQ=28 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW-
AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [a4] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: ALi Corporation PCI to AGP Controller (prog-if 00 [Normal
decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: f7f00000-fdffffff
Prefetchable memory behind bridge: 48000000-480fffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ <SERR- <PERR+
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
00:02.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) (prog-if
10 [OHCI])
Subsystem: Toshiba America Info Systems Unknown device 0004
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (20000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f7eff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.0 IDE interface: ALi Corporation M5229 IDE (rev c3) (prog-if f0)
Subsystem: Toshiba America Info Systems Unknown device 0004
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 1000ns max)
Interrupt: pin A routed to IRQ 255
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled]
[size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled]
[size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled]
[size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled]
[size=1]
Region 4: I/O ports at eff0 [size=16]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:06.0 Multimedia audio controller: ALi Corporation M5451 PCI AC-Link
Controller Audio Device (rev 01)
Subsystem: Toshiba America Info Systems Unknown device 0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR+ <PERR+
Latency: 64 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at ed00 [size=256]
Region 1: Memory at f7efe000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 ISA bridge: ALi Corporation M1533/M1535 PCI to ISA Bridge [Aladdin
IV/V/V+]
Subsystem: Toshiba America Info Systems Unknown device 0004
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [a0] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:08.0 Bridge: ALi Corporation M7101 Power Management Controller [PMU]
Subsystem: Toshiba America Info Systems Unknown device 0001
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
00:0a.0 Ethernet controller: Intel Corporation 82557/8/9 [Ethernet Pro 100]
(rev 08)
Subsystem: Toshiba America Info Systems 8255x-based Fast Ethernet
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f7efd000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at eb40 [size=64]
Region 2: Memory at f7d00000 (32-bit, non-prefetchable) [size=1M]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00:10.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller
(rev 01)
Subsystem: Lucent Technologies Unknown device ab01
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 48100000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 30000000-33fff000 (prefetchable)
Memory window 1: 34000000-37fff000
I/O window 0: 00001000-000010ff
I/O window 1: 00001400-000014ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt- PostWrite+
16-bit legacy interface ports at 0001
00:11.0 CardBus bridge: Toshiba America Info Systems ToPIC100 PCI to Cardbus
Bridge with ZV Support (rev 32)
Subsystem: Toshiba America Info Systems Unknown device 0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 48101000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=0
Memory window 0: 38000000-3bfff000 (prefetchable)
Memory window 1: 3c000000-3ffff000
I/O window 0: 00001800-000018ff
I/O window 1: 00001c00-00001cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:11.1 CardBus bridge: Toshiba America Info Systems ToPIC100 PCI to Cardbus
Bridge with ZV Support (rev 32)
Subsystem: Toshiba America Info Systems Unknown device 0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin B routed to IRQ 11
Region 0: Memory at 48102000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=0a, subordinate=0d, sec-latency=0
Memory window 0: 40000000-43fff000 (prefetchable)
Memory window 1: 44000000-47fff000
I/O window 0: 00002000-000020ff
I/O window 1: 00002400-000024ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:12.0 System peripheral: Toshiba America Info Systems SD TypA Controller
(rev 03)
Subsystem: Toshiba America Info Systems Unknown device 0001
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f7cffe00 (32-bit, non-prefetchable) [size=512]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: Trident Microsystems CyberBlade XPAi1 (rev
82) (prog-if 00 [VGA])
Subsystem: Toshiba America Info Systems Unknown device 0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 8
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=32M]
Region 1: Memory at fbc00000 (32-bit, non-prefetchable) [size=4M]
Region 2: Memory at f8000000 (32-bit, non-prefetchable) [size=32M]
Region 3: Memory at f7ff8000 (32-bit, non-prefetchable) [size=32K]
[virtual] Expansion ROM at 48000000 [disabled] [size=64K]
Capabilities: [80] AGP version 2.0
Status: RQ=33 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW-
AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [90] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
/proc/ioports:
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0100-013f : pcmcia_socket0
0170-0177 : 0000:00:04.0
0170-0177 : libata
01f0-01f7 : 0000:00:04.0
01f0-01f7 : libata
0376-0376 : 0000:00:04.0
0376-0376 : libata
03c0-03df : vesafb
03f6-03f6 : 0000:00:04.0
03f6-03f6 : libata
03f8-03ff : serial
0cf8-0cff : PCI conf1
1000-10ff : PCI CardBus #02
1400-14ff : PCI CardBus #02
1800-18ff : PCI CardBus #06
1c00-1cff : PCI CardBus #06
2000-20ff : PCI CardBus #0a
2400-24ff : PCI CardBus #0a
eb40-eb7f : 0000:00:0a.0
eb40-eb7f : e100
ed00-edff : 0000:00:06.0
ed00-edff : ALI 5451
ee00-ee3f : 0000:00:08.0
ee00-ee03 : ACPI PM1a_EVT_BLK
ee04-ee05 : ACPI PM1a_CNT_BLK
ee08-ee0b : ACPI PM_TMR
ee10-ee15 : ACPI CPU throttle
ee18-ee27 : ACPI GPE0_BLK
ee34-ee34 : ACPI PM2_CNT_BLK
ef00-ef1f : 0000:00:08.0
ef00-ef1f : ali1535_smbus
eff0-efff : 0000:00:04.0
eff0-efff : libata
/proc/iomem:
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000cbfff : Video ROM
000e0000-000eedff : reserved
000eee00-000eefff : ACPI Non-volatile Storage
000f0000-000fffff : System ROM
00100000-1ef5ffff : System RAM
00100000-002d1409 : Kernel code
002d140a-003a2c63 : Kernel data
1ef60000-1ef6ffff : ACPI Tables
1ef70000-1fffffff : reserved
30000000-33ffffff : PCI CardBus #02
34000000-37ffffff : PCI CardBus #02
38000000-3bffffff : PCI CardBus #06
3c000000-3fffffff : PCI CardBus #06
40000000-43ffffff : PCI CardBus #0a
44000000-47ffffff : PCI CardBus #0a
48000000-480fffff : PCI Bus #01
48000000-4800ffff : 0000:01:00.0
48100000-48100fff : 0000:00:10.0
48100000-48100fff : yenta_socket
48101000-48101fff : 0000:00:11.0
48101000-48101fff : yenta_socket
48102000-48102fff : 0000:00:11.1
48102000-48102fff : yenta_socket
60000000-60000fff : pcmcia_socket0
f0000000-f3ffffff : 0000:00:00.0
f7cffe00-f7cfffff : 0000:00:12.0
f7d00000-f7dfffff : 0000:00:0a.0
f7d00000-f7dfffff : e100
f7efd000-f7efdfff : 0000:00:0a.0
f7efd000-f7efdfff : e100
f7efe000-f7efefff : 0000:00:06.0
f7efe000-f7efefff : ALI 5451
f7eff000-f7efffff : 0000:00:02.0
f7eff000-f7efffff : ohci_hcd
f7f00000-fdffffff : PCI Bus #01
f7ff8000-f7ffffff : 0000:01:00.0
f8000000-f9ffffff : 0000:01:00.0
fbc00000-fbffffff : 0000:01:00.0
fc000000-fdffffff : 0000:01:00.0
fc000000-fcffffff : vesafb
fff80000-ffffffff : reserved
dmesg (I played around with smsc so you will see several attempts):
[ 0.000000] Linux version 2.6.22-rc4-2avb (bor@cooker) (gcc version 4.1.2
20070302 (prerelease) (4.1.2-1mdv2007.1)) #13 Sun Jun 10 21:04:18 MSD 2007
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 00000000000eee00 (reserved)
[ 0.000000] BIOS-e820: 00000000000eee00 - 00000000000ef000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000000ef000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000001ef60000 (usable)
[ 0.000000] BIOS-e820: 000000001ef60000 - 000000001ef70000 (ACPI data)
[ 0.000000] BIOS-e820: 000000001ef70000 - 0000000020000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] 495MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 126816) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 126816
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 126816
[ 0.000000] On node 0 totalpages: 126816
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 958 pages used for memmap
[ 0.000000] Normal zone: 121762 pages, LIFO batch:31
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP 000F0090, 0014 (r0 TOSHIB)
[ 0.000000] ACPI: RSDT 1EF60000, 0028 (r1 TOSHIB 750 970814 TASM
4010000)
[ 0.000000] ACPI: FACP 1EF60054, 0084 (r2 TOSHIB 750 970814 TASM
4010000)
[ 0.000000] ACPI: DSDT 1EF600D8, 68DA (r1 TOSHIB 4000 20020417 MSFT
100000A)
[ 0.000000] ACPI: FACS 000EEE00, 0040
[ 0.000000] ACPI: PM-Timer IO Port: 0xee08
[ 0.000000] Allocating PCI resources starting at 30000000 (gap:
20000000:dff80000)
[ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 -
00000000000a0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 -
00000000000e0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000e0000 -
00000000000ee000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000ee000 -
00000000000ef000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000ef000 -
0000000000100000
[ 0.000000] Built 1 zonelists. Total pages: 125826
[ 0.000000] Kernel command line: BOOT_IMAGE=2.6.22-rc4-kbd-2avb
root=LABEL=/ resume=/dev/sda1 vga=791
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] Detected 747.678 MHz processor.
[ 62.470759] Console: colour dummy device 80x25
[ 62.471005] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc.,
Ingo Molnar
[ 62.471023] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 62.471033] ... MAX_LOCK_DEPTH: 30
[ 62.471043] ... MAX_LOCKDEP_KEYS: 2048
[ 62.471053] ... CLASSHASH_SIZE: 1024
[ 62.471063] ... MAX_LOCKDEP_ENTRIES: 8192
[ 62.471073] ... MAX_LOCKDEP_CHAINS: 16384
[ 62.471083] ... CHAINHASH_SIZE: 8192
[ 62.471093] memory used by lock dependency info: 992 kB
[ 62.471104] per task-struct memory footprint: 1200 bytes
[ 62.471116] ------------------------
[ 62.471125] | Locking API testsuite:
[
62.471135] ----------------------------------------------------------------------------
[ 62.471151] | spin |wlock |rlock |mutex |
wsem | rsem |
[
62.471167] --------------------------------------------------------------------------
[ 62.471213] A-A deadlock: ok | ok | ok | ok |
ok | ok |
[ 62.473811] A-B-B-A deadlock: ok | ok | ok | ok |
ok | ok |
[ 62.475664] A-B-B-C-C-A deadlock: ok | ok | ok | ok |
ok | ok |
[ 62.477554] A-B-C-A-B-C deadlock: ok | ok | ok | ok |
ok | ok |
[ 62.479448] A-B-B-C-C-D-D-A deadlock: ok | ok | ok | ok |
ok | ok |
[ 62.481400] A-B-C-D-B-D-D-A deadlock: ok | ok | ok | ok |
ok | ok |
[ 62.483358] A-B-C-D-B-C-D-A deadlock: ok | ok | ok | ok |
ok | ok |
[ 62.485325] double unlock: ok | ok | ok | ok |
ok | ok |
[ 62.487123] initialize held: ok | ok | ok | ok |
ok | ok |
[ 62.488913] bad unlock order: ok | ok | ok | ok |
ok | ok |
[
62.490761] --------------------------------------------------------------------------
[ 62.490777] recursive read-lock: |
ok | | ok |
[ 62.491390] recursive read-lock #2: |
ok | | ok |
[ 62.492001] mixed read-write-lock: |
ok | | ok |
[ 62.492618] mixed write-read-lock: |
ok | | ok |
[
62.493235] --------------------------------------------------------------------------
[ 62.493251] hard-irqs-on + irq-safe-A/12: ok | ok | ok |
[ 62.494162] soft-irqs-on + irq-safe-A/12: ok | ok | ok |
[ 62.495081] hard-irqs-on + irq-safe-A/21: ok | ok | ok |
[ 62.495984] soft-irqs-on + irq-safe-A/21: ok | ok | ok |
[ 62.496891] sirq-safe-A => hirqs-on/12: ok | ok | ok |
[ 62.497798] sirq-safe-A => hirqs-on/21: ok | ok | ok |
[ 62.498705] hard-safe-A + irqs-on/12: ok | ok | ok |
[ 62.499612] soft-safe-A + irqs-on/12: ok | ok | ok |
[ 62.500524] hard-safe-A + irqs-on/21: ok | ok | ok |
[ 62.501432] soft-safe-A + irqs-on/21: ok | ok | ok |
[ 62.502339] hard-safe-A + unsafe-B #1/123: ok | ok | ok |
[ 62.503273] soft-safe-A + unsafe-B #1/123: ok | ok | ok |
[ 62.504207] hard-safe-A + unsafe-B #1/132: ok | ok | ok |
[ 62.505137] soft-safe-A + unsafe-B #1/132: ok | ok | ok |
[ 62.506067] hard-safe-A + unsafe-B #1/213: ok | ok | ok |
[ 62.506997] soft-safe-A + unsafe-B #1/213: ok | ok | ok |
[ 62.507929] hard-safe-A + unsafe-B #1/231: ok | ok | ok |
[ 62.508855] soft-safe-A + unsafe-B #1/231: ok | ok | ok |
[ 62.509782] hard-safe-A + unsafe-B #1/312: ok | ok | ok |
[ 62.510695] soft-safe-A + unsafe-B #1/312: ok | ok | ok |
[ 62.511611] hard-safe-A + unsafe-B #1/321: ok | ok | ok |
[ 62.512538] soft-safe-A + unsafe-B #1/321: ok | ok | ok |
[ 62.513465] hard-safe-A + unsafe-B #2/123: ok | ok | ok |
[ 62.514395] soft-safe-A + unsafe-B #2/123: ok | ok | ok |
[ 62.515330] hard-safe-A + unsafe-B #2/132: ok | ok | ok |
[ 62.516258] soft-safe-A + unsafe-B #2/132: ok | ok | ok |
[ 62.517192] hard-safe-A + unsafe-B #2/213: ok | ok | ok |
[ 62.518121] soft-safe-A + unsafe-B #2/213: ok | ok | ok |
[ 62.519053] hard-safe-A + unsafe-B #2/231: ok | ok | ok |
[ 62.519978] soft-safe-A + unsafe-B #2/231: ok | ok | ok |
[ 62.520907] hard-safe-A + unsafe-B #2/312: ok | ok | ok |
[ 62.521834] soft-safe-A + unsafe-B #2/312: ok | ok | ok |
[ 62.522768] hard-safe-A + unsafe-B #2/321: ok | ok | ok |
[ 62.523696] soft-safe-A + unsafe-B #2/321: ok | ok | ok |
[ 62.524626] hard-irq lock-inversion/123: ok | ok | ok |
[ 62.525557] soft-irq lock-inversion/123: ok | ok | ok |
[ 62.526493] hard-irq lock-inversion/132: ok | ok | ok |
[ 62.527420] soft-irq lock-inversion/132: ok | ok | ok |
[ 62.528355] hard-irq lock-inversion/213: ok | ok | ok |
[ 62.529287] soft-irq lock-inversion/213: ok | ok | ok |
[ 62.530223] hard-irq lock-inversion/231: ok | ok | ok |
[ 62.531149] soft-irq lock-inversion/231: ok | ok | ok |
[ 62.532082] hard-irq lock-inversion/312: ok | ok | ok |
[ 62.533011] soft-irq lock-inversion/312: ok | ok | ok |
[ 62.533948] hard-irq lock-inversion/321: ok | ok | ok |
[ 62.534875] soft-irq lock-inversion/321: ok | ok | ok |
[ 62.535806] hard-irq read-recursion/123: ok |
[ 62.536124] soft-irq read-recursion/123: ok |
[ 62.536444] hard-irq read-recursion/132: ok |
[ 62.536762] soft-irq read-recursion/132: ok |
[ 62.537082] hard-irq read-recursion/213: ok |
[ 62.537400] soft-irq read-recursion/213: ok |
[ 62.537719] hard-irq read-recursion/231: ok |
[ 62.538036] soft-irq read-recursion/231: ok |
[ 62.538354] hard-irq read-recursion/312: ok |
[ 62.538671] soft-irq read-recursion/312: ok |
[ 62.538990] hard-irq read-recursion/321: ok |
[ 62.539308] soft-irq read-recursion/321: ok |
[ 62.539629] -------------------------------------------------------
[ 62.539643] Good, all 218 testcases passed! |
[ 62.539653] ---------------------------------
[ 62.541298] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 62.544144] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 62.648193] Memory: 495900k/507264k available (1861k kernel code, 10784k
reserved, 838k data, 184k init, 0k highmem)
[ 62.648272] virtual kernel memory layout:
[ 62.648277] fixmap : 0xffff8000 - 0xfffff000 ( 28 kB)
[ 62.648282] vmalloc : 0xdf800000 - 0xffff6000 ( 519 MB)
[ 62.648286] lowmem : 0xc0000000 - 0xdef60000 ( 495 MB)
[ 62.648290] .init : 0xc03a6000 - 0xc03d4000 ( 184 kB)
[ 62.648294] .data : 0xc02d140a - 0xc03a2c64 ( 838 kB)
[ 62.648298] .text : 0xc0100000 - 0xc02d140a (1861 kB)
[ 62.648344] Checking if this processor honours the WP bit even in
supervisor mode... Ok.
[ 62.732548] Calibrating delay using timer specific routine.. 1497.68
BogoMIPS (lpj=2495503)
[ 62.732851] Mount-cache hash table entries: 512
[ 62.733789] CPU: After generic identify, caps: 0383f9ff 00000000 00000000
00000000 00000000 00000000 00000000
[ 62.733825] CPU: L1 I cache: 16K, L1 D cache: 16K
[ 62.733844] CPU: L2 cache: 256K
[ 62.733861] CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040
00000000 00000000 00000000
[ 62.733898] Compat vDSO mapped to ffffe000.
[ 62.733953] CPU: Intel Pentium III (Coppermine) stepping 0a
[ 62.733982] Checking 'hlt' instruction... OK.
[ 62.746236] ACPI: Core revision 20070126
[ 62.766712] Parsing all Control Methods:
[ 62.767183] Table [DSDT](id 0001) - 683 Objects with 60 Devices 195 Methods
10 Regions
[ 62.767216] tbxface-0587 [02] tb_load_namespace : ACPI Tables
successfully acquired
[ 62.767245] ACPI: setting ELCR to 0200 (from 0a00)
[ 62.767811] evxfevnt-0091 [02] enable : Transition to ACPI
mode successful
[ 62.769429] NET: Registered protocol family 16
[ 62.770649] ACPI: bus type pci registered
[ 62.771700] PCI: PCI BIOS revision 2.10 entry at 0xfe5ae, last bus=5
[ 62.771716] PCI: Using configuration type 1
[ 62.771726] Setting up standard PCI resources
[ 62.780975] evgpeblk-0952 [04] ev_create_gpe_block : GPE 00 to 3F [_GPE]
8 regs on int 0x9
[ 62.784458] evgpeblk-1048 [03] ev_initialize_gpe_bloc: Found 3 Wake,
Enabled 0 Runtime GPEs in this block
[ 62.785892] Completing Region/Field/Buffer/Package
initialization:........................................
[ 62.790995] Initialized 8/10 Regions 0/0 Fields 16/16 Buffers 16/27
Packages (692 nodes)
[ 62.791019] Initializing Device/Processor/Thermal objects by executing _INI
methods:.
[ 62.795837] Executed 1 _INI methods requiring 0 _STA executions (examined
64 objects)
[ 62.795947] ACPI: Interpreter enabled
[ 62.795963] ACPI: (supports S0 S3 S4 S5)
[ 62.796153] ACPI: Using PIC for interrupt routing
[ 62.839902] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 62.840045] PCI: Probing PCI hardware (bus 00)
[ 62.841201] PCI quirk: region ee00-ee3f claimed by ali7101 ACPI
[ 62.841225] PCI quirk: region ef00-ef1f claimed by ali7101 SMB
[ 62.842978] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 62.843697] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
[ 62.882557] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11)
[ 62.883832] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11)
[ 62.885042] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11)
[ 62.886305] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11)
[ 62.887525] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11)
[ 62.888737] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11)
[ 62.890370] ACPI: Power Resource [PFAN] (off)
[ 62.890436] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 62.890562] pnp: PnP ACPI init
[ 62.890691] ACPI: bus type pnp registered
[ 62.954051] pnp: PnP ACPI: found 12 devices
[ 62.954101] ACPI: ACPI bus type pnp unregistered
[ 62.954430] PCI: Using ACPI for IRQ routing
[ 62.954448] PCI: If a device doesn't work, try "pci=routeirq". If it
helps, post a report
[ 62.965460] pnp: 00:00: iomem range 0x0-0x9ffff could not be reserved
[ 62.965489] pnp: 00:00: iomem range 0xe0000-0xeffff could not be reserved
[ 62.965506] pnp: 00:00: iomem range 0xf0000-0xfffff could not be reserved
[ 62.965524] pnp: 00:00: iomem range 0x100000-0x1ef5ffff could not be
reserved
[ 62.965785] Time: tsc clocksource has been installed.
[ 62.997630] PCI: Bridge: 0000:00:01.0
[ 62.997661] IO window: disabled.
[ 62.997682] MEM window: f7f00000-fdffffff
[ 62.997699] PREFETCH window: 48000000-480fffff
[ 62.997720] PCI: Bus 2, cardbus bridge: 0000:00:10.0
[ 62.997733] IO window: 00001000-000010ff
[ 62.997749] IO window: 00001400-000014ff
[ 62.997765] PREFETCH window: 30000000-33ffffff
[ 62.997781] MEM window: 34000000-37ffffff
[ 62.997797] PCI: Bus 6, cardbus bridge: 0000:00:11.0
[ 62.997809] IO window: 00001800-000018ff
[ 62.997824] IO window: 00001c00-00001cff
[ 62.997841] PREFETCH window: 38000000-3bffffff
[ 62.997857] MEM window: 3c000000-3fffffff
[ 62.997874] PCI: Bus 10, cardbus bridge: 0000:00:11.1
[ 62.997885] IO window: 00002000-000020ff
[ 62.997901] IO window: 00002400-000024ff
[ 62.997917] PREFETCH window: 40000000-43ffffff
[ 62.997934] MEM window: 44000000-47ffffff
[ 62.997972] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 62.998018] PCI: Enabling device 0000:00:10.0 (0000 -> 0003)
[ 63.000663] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
[ 63.000694] PCI: setting IRQ 11 as level-triggered
[ 63.000703] ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKC] -> GSI 11
(level, low) -> IRQ 11
[ 63.000762] PCI: Enabling device 0000:00:11.0 (0000 -> 0003)
[ 63.002889] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
[ 63.002906] ACPI: PCI Interrupt 0000:00:11.0[A] -> Link [LNKA] -> GSI 11
(level, low) -> IRQ 11
[ 63.002961] PCI: Enabling device 0000:00:11.1 (0000 -> 0003)
[ 63.005055] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
[ 63.005071] ACPI: PCI Interrupt 0000:00:11.1[B] -> Link [LNKB] -> GSI 11
(level, low) -> IRQ 11
[ 63.005213] NET: Registered protocol family 2
[ 63.036018] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 63.036544] TCP established hash table entries: 16384 (order: 7, 720896
bytes)
[ 63.043090] TCP bind hash table entries: 16384 (order: 7, 720896 bytes)
[ 63.049915] TCP: Hash tables configured (established 16384 bind 16384)
[ 63.050082] TCP reno registered
[ 63.059914] checking if image is initramfs... it is
[ 63.277188] Freeing initrd memory: 1171k freed
[ 63.279813] audit: initializing netlink socket (disabled)
[ 63.279958] audit(1181566616.319:1): initialized
[ 63.281313] io scheduler noop registered
[ 63.281345] io scheduler anticipatory registered
[ 63.281357] io scheduler deadline registered
[ 63.281416] io scheduler cfq registered (default)
[ 63.281501] Activating ISA DMA hang workarounds.
[ 63.281548] Boot video device is 0000:01:00.0
[ 63.282463] vesafb: framebuffer at 0xfc000000, mapped to 0xdf880000, using
3072k, total 16384k
[ 63.282499] vesafb: mode is 1024x768x16, linelength=2048, pages=9
[ 63.282513] vesafb: protected mode interface info at c000:775e
[ 63.282527] vesafb: pmi: set display start = c00c777f, set palette =
c00c77e2
[ 63.282539] vesafb: scrolling: redraw
[ 63.282553] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[ 63.353029] Console: switching to colour frame buffer device 128x48
[ 63.416464] fb0: VESA VGA frame buffer device
[ 63.499013] Switched to high resolution mode on CPU 0
[ 63.720982] Real Time Clock Driver v1.12ac
[ 63.726162] RAMDISK driver initialized: 16 RAM disks of 32000K size 1024
blocksize
[ 63.728972] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64
irq 1,12
[ 63.734870] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 63.735602] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 63.737242] mice: PS/2 mouse device common for all mice
[ 63.738753] NET: Registered protocol family 1
[ 63.739484] Using IPI Shortcut mode
[ 63.741458] BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
[ 63.743207] Freeing unused kernel memory: 184k freed
[ 63.744180] Write protecting the kernel text: 1864k
[ 63.744842] Write protecting the kernel read-only data: 684k
[ 63.778506] SCSI subsystem initialized
[ 63.795649] input: AT Translated Set 2 keyboard as /class/input/input0
[ 63.857915] libata version 2.21 loaded.
[ 63.890575] ACPI: Unable to derive IRQ for device 0000:00:04.0
[ 63.915820] ACPI: PCI Interrupt 0000:00:04.0[A]: no GSI
[ 63.941192] scsi0 : pata_ali
[ 63.966093] scsi1 : pata_ali
[ 63.990183] ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma
0x0001eff0 irq 14
[ 64.014754] ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma
0x0001eff8 irq 15
[ 64.199340] ata1.00: ata_hpa_resize 1: sectors = 39070080, hpa_sectors =
39070080
[ 64.223901] ata1.00: ATA-5: IC25N020ATDA04-0, DA3OA70A, max UDMA/100
[ 64.248487] ata1.00: 39070080 sectors, multi 0: LBA
[ 64.272985] ata1.00: limited to UDMA/33 due to 40-wire cable
[ 64.309244] ata1.00: ata_hpa_resize 1: sectors = 39070080, hpa_sectors =
39070080
[ 64.334495] ata1.00: configured for UDMA/33
[ 64.688923] ata2.00: ATAPI, max UDMA/33
[ 64.895513] ata2.00: configured for UDMA/33
[ 64.921423] scsi 0:0:0:0: Direct-Access ATA IC25N020ATDA04-0 DA3O
PQ: 0 ANSI: 5
[ 64.949936] scsi 1:0:0:0: CD-ROM TOSHIBA DVD-ROM SD-C2502 1313
PQ: 0 ANSI: 5
[ 65.009344] sd 0:0:0:0: [sda] 39070080 512-byte hardware sectors (20004 MB)
[ 65.035141] sd 0:0:0:0: [sda] Write Protect is off
[ 65.060285] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 65.060389] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 65.086647] sd 0:0:0:0: [sda] 39070080 512-byte hardware sectors (20004 MB)
[ 65.112551] sd 0:0:0:0: [sda] Write Protect is off
[ 65.137989] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 65.138122] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 65.164116] sda: sda1 sda2
[ 65.207818] sd 0:0:0:0: [sda] Attached SCSI disk
[ 65.584173] swsusp: Marking nosave pages: 000000000009f000 -
0000000000100000
[ 65.584199] swsusp: Basic memory bitmaps created
[ 65.620553] swsusp: Basic memory bitmaps freed
[ 65.749800] ReiserFS: sda2: found reiserfs format "3.6" with standard
journal
[ 65.775054] ReiserFS: sda2: using ordered data mode
[ 65.817514] ReiserFS: sda2: journal params: device sda2, size 8192, journal
first block 18, max trans len 1024, max batch 900, max commit age 30, max
trans age 30
[ 65.877779] ReiserFS: sda2: checking transaction log (sda2)
[ 65.933489] ReiserFS: sda2: Using r5 hash to sort names
[ 74.272441] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 74.272528] scsi 1:0:0:0: Attached scsi generic sg1 type 5
[ 74.490146] Linux agpgart interface v0.102 (c) Dave Jones
[ 74.542589] usbcore: registered new interface driver usbfs
[ 74.542854] usbcore: registered new interface driver hub
[ 74.543072] usbcore: registered new device driver usb
[ 74.711847] agpgart: Detected ALi M1644 chipset
[ 74.721726] agpgart: AGP aperture is 64M @ 0xf0000000
[ 74.772905] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI)
Driver
[ 74.775874] ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 11
[ 74.775892] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKG] -> GSI 11
(level, low) -> IRQ 11
[ 74.775956] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 74.777721] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus
number 1
[ 74.777815] ohci_hcd 0000:00:02.0: irq 11, io mem 0xf7eff000
[ 74.831804] usb usb1: configuration #1 chosen from 1 choice
[ 74.832118] hub 1-0:1.0: USB hub found
[ 74.832217] hub 1-0:1.0: 3 ports detected
[ 74.955768] Yenta: CardBus bridge found at 0000:00:10.0 [12a3:ab01]
[ 74.955818] Yenta: Enabling burst memory read transactions
[ 74.955830] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 74.955836] Yenta: Routing CardBus interrupts to PCI
[ 74.955848] Yenta TI: socket 0000:00:10.0, mfunc 0x01000002, devctl 0x60
[ 74.977822] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
[ 74.977838] e100: Copyright(c) 1999-2006 Intel Corporation
[ 75.063210] sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray
[ 75.063234] Uniform CD-ROM driver Revision: 3.20
[ 75.063700] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 75.185635] Yenta: ISA IRQ mask 0x0000, PCI irq 11
[ 75.185652] Socket status: 30000011
[ 75.186622] Yenta: CardBus bridge found at 0000:00:11.0 [1179:0001]
[ 75.315688] Yenta: ISA IRQ mask 0x04b8, PCI irq 11
[ 75.315703] Socket status: 30000007
[ 75.316398] Yenta: CardBus bridge found at 0000:00:11.1 [1179:0001]
[ 75.442242] Yenta: ISA IRQ mask 0x04b8, PCI irq 11
[ 75.442259] Socket status: 30000007
[ 75.448429] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
[ 75.448457] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKD] -> GSI 11
(level, low) -> IRQ 11
[ 75.477665] e100: eth0: e100_probe: addr 0xf7efd000, irq 11, MAC addr
00:00:39:D7:14:A1
[ 75.491638] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
[ 75.491664] ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LNKH] -> GSI 11
(level, low) -> IRQ 11
[ 75.563140] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ
sharing enabled
[ 75.715360] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 75.818143] pccard: PCMCIA card inserted into slot 0
[ 76.208122] NET: Registered protocol family 23
[ 79.924209] cs: memory probe 0x0c0000-0x0fffff: excluding 0xc0000-0xcbfff
0xe0000-0xfffff
[ 79.927926] cs: memory probe 0x60000000-0x60ffffff: clean.
[ 79.939570] cs: memory probe 0xa0000000-0xa0ffffff: clean.
[ 79.951819] pcmcia: registering new device pcmcia0.0
[ 80.382434] wlags49_h1_cs v7.18 for PCMCIA, 03/31/2004 14:31:00 by Agere
Systems, http://www.agere.com
[ 80.382454] *** Modified for kernel 2.6 by Andrey Borzenkov
<arvidjaar@xxxxxxx> $Revision: 39 $
[ 80.382463] *** Station Mode (STA) Support: YES
[ 80.382469] *** Access Point Mode (AP) Support: YES
[ 80.871844] eth1: PRI 31 variant 2 version 9.48
[ 80.871913] eth1: NIC 5 variant 2 version 1.02
[ 80.875729] eth1: Wireless, io_addr 0x100, irq 11, mac_address
00:02:2D:26:95:6C
[ 81.373545] Toshiba System Managment Mode driver v1.11 26/9/2001
[ 81.579468] Non-volatile memory driver v1.2
[ 81.641830] input: ImPS/2 Generic Wheel Mouse as /class/input/input1
[ 82.480744] ACPI: AC Adapter [ADP1] (off-line)
[ 82.503628] ACPI: Battery Slot [BAT1] (battery present)
[ 82.503904] ACPI: Battery Slot [BAT2] (battery absent)
[ 82.565695] input: Power Button (FF) as /class/input/input2
[ 82.696658] ACPI: Power Button (FF) [PWRF]
[ 82.723225] input: Lid Switch as /class/input/input3
[ 82.812408] ACPI: Lid Switch [LID]
[ 82.932730] ACPI: Transitioning device [FAN] to D3
[ 82.932747] ACPI: Transitioning device [FAN] to D3
[ 82.932762] ACPI: Fan [FAN] (off)
[ 82.967034] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 83.033930] ACPI: Thermal Zone [THRM] (39 C)
[ 20.443331] Marking TSC unstable due to: possible TSC halt in C2.
[ 20.446664] Time: acpi_pm clocksource has been installed.
[ 20.449997] toshiba_acpi: Toshiba Laptop ACPI Extras version 0.18
[ 20.449997] toshiba_acpi: HCI method: \_SB_.VALD.GHCI
[ 20.486664] ACPI: Video Device [VGA] (multi-head: yes rom: yes post: no)
[ 20.653331] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised:
dm-devel@xxxxxxxxxx
[ 20.849997] Clocksource tsc unstable (delta = -90684000 ns)
[ 21.019997] loop: module loaded
[ 25.353330] Adding 500432k swap on /dev/sda1. Priority:-1 extents:1
across:500432k
[ 38.063329] usbcore: registered new interface driver usbhid
[ 38.063329] /home/bor/src/linux-git/drivers/hid/usbhid/hid-core.c: v2.6:USB
HID core driver
[ 40.703329] process `syslogd' is using obsolete setsockopt SO_BSDCOMPAT
[ 43.983328] Bluetooth: Core ver 2.11
[ 43.983328] NET: Registered protocol family 31
[ 43.983328] Bluetooth: HCI device and connection manager initialized
[ 43.983328] Bluetooth: HCI socket layer initialized
[ 44.436662] Bluetooth: L2CAP ver 2.8
[ 44.436662] Bluetooth: L2CAP socket layer initialized
[ 45.383328] Bluetooth: RFCOMM socket layer initialized
[ 45.383328] Bluetooth: RFCOMM TTY layer initialized
[ 45.383328] Bluetooth: RFCOMM ver 1.8
[ 46.743328] NET: Registered protocol family 17
[ 50.486661] eth1: PRI 31 variant 2 version 9.48
[ 50.486661] eth1: NIC 5 variant 2 version 1.02
[ 51.476661] eth1: PRI 31 variant 2 version 9.48
[ 51.476661] eth1: NIC 5 variant 2 version 1.02
[ 51.796661] eth1: PRI 31 variant 2 version 9.48
[ 51.796661] eth1: NIC 5 variant 2 version 1.02
[ 2932.806373] pccard: card ejected from slot 0
[ 3021.556364] pnp: Device 00:0a activated.
[ 3021.556364] smsc_ircc_present(), addr 0x02e8 - no device found!
[ 3021.556364] PnP probe failed
[ 3021.556364] Detected unconfigured Toshiba laptop with ALi ISA bridge SMSC
IrDA chip, pre-configuring device.
[ 3021.556364] Activated ALi 1533 ISA bridge port 0x02e8.
[ 3021.556364] Activated ALi 1533 ISA bridge port 0x02f8.
[ 3021.556364] found SMC SuperIO Chip (devid=0x5a rev=00 base=0x002e):
LPC47N227
[ 3021.556364] smsc_superio_flat(): IrDA not enabled
[ 3021.556364] smsc_superio_flat(): fir: 0x2f8, sir: 0x2e8, dma: 03, irq: 7,
mode: 0x02
[ 3021.556364] SMsC IrDA Controller found
[ 3021.556364] IrCC version 2.0, firport 0x2f8, sirport 0x2e8 dma=3, irq=7
[ 3021.559697] No transceiver found. Defaulting to Fast pin select
[ 3044.583028] pnp: Device 00:0a disabled.
[ 3543.909645] pnp: Device 00:0a activated.
[ 3543.909645] printk: 1 messages suppressed.
[ 3543.909645] smsc_ircc_present(), addr 0x0100 - no device found!
[ 3543.909645] PnP probe failed
[ 3543.912978] Detected unconfigured Toshiba laptop with ALi ISA bridge SMSC
IrDA chip, pre-configuring device.
[ 3543.912978] Activated ALi 1533 ISA bridge port 0x02e8.
[ 3543.912978] Activated ALi 1533 ISA bridge port 0x02f8.
[ 3543.912978] found SMC SuperIO Chip (devid=0x5a rev=00 base=0x002e):
LPC47N227
[ 3543.912978] smsc_superio_flat(): fir: 0x2f8, sir: 0x2e8, dma: 03, irq: 7,
mode: 0x0a
[ 3543.912978] SMsC IrDA Controller found
[ 3543.912978] IrCC version 2.0, firport 0x2f8, sirport 0x2e8 dma=3, irq=7
[ 3543.912978] No transceiver found. Defaulting to Fast pin select
[ 3543.922978] IrDA: Registered device irda0
[ 3605.166306] pnp: Device 00:0a disabled.
[ 3615.652971] pccard: PCMCIA card inserted into slot 0
[ 3615.652971] pcmcia: registering new device pcmcia0.0
[ 3615.949638] wlags49_h1_cs v7.18 for PCMCIA, 03/31/2004 14:31:00 by Agere
Systems, http://www.agere.com
[ 3615.949638] *** Modified for kernel 2.6 by Andrey Borzenkov
<arvidjaar@xxxxxxx> $Revision: 39 $
[ 3615.949638] *** Station Mode (STA) Support: YES
[ 3615.949638] *** Access Point Mode (AP) Support: YES
[ 3615.996305] eth1: PRI 31 variant 2 version 9.48
[ 3615.996305] eth1: NIC 5 variant 2 version 1.02
[ 3616.456305] eth1: Wireless, io_addr 0x100, irq 11, mac_address
00:02:2D:26:95:6C
[ 3617.152971] eth1: PRI 31 variant 2 version 9.48
[ 3617.152971] eth1: NIC 5 variant 2 version 1.02
[ 3617.539638] eth1: PRI 31 variant 2 version 9.48
[ 3617.539638] eth1: NIC 5 variant 2 version 1.02
[ 3617.906304] eth1: PRI 31 variant 2 version 9.48
[ 3617.906304] eth1: NIC 5 variant 2 version 1.02
available_resources_io:
0x00000100 - 0x000003af
0x000003e0 - 0x000004ff
0x00000820 - 0x000008ff
0x00000a00 - 0x00000aff
0x00000c00 - 0x00000cf7
available_resources_mem:
0x000cc000 - 0x000dffff
0x60000000 - 0x60ffffff
0xa0000000 - 0xa0ffffff
Attachment:
signature.asc
Description: This is a digitally signed message part.