Re: Linux 2.6.23-rc3

[Zilvinas Valinskas]

Hello Michal, 

This morning I have booted laptop, for a while fan had been turned off.
But then after a light load (compiling stuff & co), fan was turned on
and now it is still on. 

zilvinas@zv:~$ acpi -bt
     Battery 1: charged, 97%
     Thermal 1: ok, 48.0 degrees C
     Thermal 2: ok, 37.0 degrees C
     Thermal 3: ok, 46.0 degrees C
     Thermal 4: ok, 37.0 degrees C
     Thermal 5: ok, 32.0 degrees C
     Thermal 6: ok, 20.0 degrees C

Temperatures don't seem to be that high to keep the fan on.

Z. 

On Mon, 2007-08-13 at 18:49 +0200, Michal Piotrowski wrote:
> Hi Zilvinas,
> 
> On 13/08/07, Zilvinas Valinskas <zilvinas@xxxxxxxxxxx> wrote:
> > Hello lkml,
> >
> > Linux kernel v2.6.23-rc3 booted ok and so far everything is fine. I have
> > HP Compaq nx9420 laptop (Dual Core).
> >
> > Just a few things that I found interesting:
> >
> > 1. /sys/devices/system/clocksource/clocksource0/*
> >
> > $ sudo grep . *
> > available_clocksource:hpet hpet acpi_pm jiffies tsc
> >                       ^^^^^^^^^ listed twice ;) not a big deal but still.
> > current_clocksource:hpet
> >                     ^^^^ seems selected ;) although in dmesg there are
> >
> > $ dmesg | grep -i hpet
> > $ dmesg | grep -i hpet
> > ACPI: HPET 7FFE59BC, 0038 (r1 HP     309F            1 HP          1)
> > ACPI: HPET id: 0x8086a201 base: 0xfed00000
> > hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
> > hpet0: 3 64-bit timers, 14318180 Hz
> > hpet_resources: 0xfed00000 is busy
> > ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ ? strange.
> >
> > Time: hpet clocksource has been installed.
> >
> > 2. ACPI related (?) - one fan is always on, even when system is idling.
> >
> > It never stops ;)
> 
> Hmmm... looks like a thermal trip points problem.
> 
> >
> > $ acpi -bt
> >      Battery 1: charged, 98%
> >      Thermal 1: ok, 48.0 degrees C
> >      Thermal 2: ok, 38.0 degrees C
> >      Thermal 3: active[5], 47.0 degrees C
> >      Thermal 4: ok, 37.0 degrees C
> >      Thermal 5: ok, 32.0 degrees C
> >      Thermal 6: ok, 25.0 degrees C
> >
> >
> > In earlier kernel versions it was turned on when needed (mostly during
> > compilation ...) and then when system is cooled  enough fan was
> > automatically turned off.
> >
> > 3. the same messages are printed twice (2.6.23-rc2 was fine).
> >
> > Brought up 2 CPUs
> > NET: Registered protocol family 16
> > ACPI: bus type pci registered
> > PCI: BIOS Bug: MCFG area at f8000000 is not E820-reserved
> > PCI: Not using MMCONFIG.
> > PCI: Using configuration type 1
> > ACPI: EC: Look up EC in DSDT
> > ACPI: EC: GPE = 0x16, I/O: command/status = 0x66, data = 0x62
> > ^^^^^^^^^^^^^^^^^^^^^^^^ 1st time
> > ACPI: Interpreter enabled
> > ACPI: (supports S0 S3)
> > ACPI: Using IOAPIC for interrupt routing
> > ACPI: EC: GPE = 0x16, I/O: command/status = 0x66, data = 0x62
> > ^^^^^^^^^^^^^^^^^^^^^^^^ 2nd time
> > ACPI: PCI Root Bridge [C003] (0000:00)
> >
> >
> > Otherwise I am happy with 2.6.23-rc3. Thank y'all ;)
> >
> > Best regards,
> > Zilvinas
> 
> Regards,
> Michal
> 

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/