Re: sata_nv + ADMA + Samsung disk problem
From: Gabor Gombas
Date: Thu Aug 16 2007 - 12:06:52 EST
Hi,
On Tue, Aug 14, 2007 at 06:30:28PM +0900, Tejun Heo wrote:
> Hmmm... That's timeout on cache flush, indicative of failing disk.
> Please post the result of 'smartctl -a /dev/sdc'.
Ok, so something is fishy in 2.6.22 wrt. SMART.
First, booting back to 2.6.20.5 I confirmed that SMART works without any
problems for all 4 disks, so all the following is a regression in
2.6.22.
I have 4 disks: two Maxtors (hdparm -I output below): sda/sdb, and two
Samsung (hdparm -I output is in my previous mail): sdc/sdd.
<==================== cut ====================>
/dev/sda:
ATA device, with non-removable media
Model Number: Maxtor 6B250S0
Serial Number: XXXXXXXX
Firmware Revision: BANC1G10
Standards:
Used: ATA/ATAPI-7 T13 1532D revision 0
Supported: 7 6 5 4
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 490234752
device size with M = 1024*1024: 239372 MBytes
device size with M = 1000*1000: 251000 MBytes (251 GB)
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Advanced power management level: unknown setting (0x0000)
Recommended acoustic management value: 192, current value: 128
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_VERIFY command
* WRITE_BUFFER command
* READ_BUFFER command
* NOP cmd
* DOWNLOAD_MICROCODE
Advanced Power Management feature set
SET_MAX security extension
* Automatic Acoustic Management feature set
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
Media Card Pass-Through
* General Purpose Logging feature set
* WRITE_{DMA|MULTIPLE}_FUA_EXT
* URG for READ_STREAM[_DMA]_EXT
* URG for WRITE_STREAM[_DMA]_EXT
* SATA-I signaling speed (1.5Gb/s)
* Native Command Queueing (NCQ)
Software settings preservation
* SMART Command Transport (SCT) feature set
* SCT Data Tables (AC5)
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
not supported: enhanced erase
Checksum: correct
<==================== cut ====================>
Under 2.6.22.1, when I try to do "smartctl -d ata -s on /dev/sd[ab]" or
"smartctl -d ata -a /dev/sd[ab]", I get the following error:
<==================== cut ====================>
smartctl version 5.37 [x86_64-unknown-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Maxtor DiamondMax 10 family (ATA/133 and SATA/150)
Device Model: Maxtor 6B250S0
Serial Number: XXXXXXXX
Firmware Version: BANC1G10
User Capacity: 251,000,193,024 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Wed Aug 15 12:01:38 2007 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
Error SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
CMD=0x50
FR =0x00
NS =0x00
SC =0x00
CL =0xc2
CH =0x00
SEL=0x00
A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options.
<==================== cut ====================>
To repeat, this does not happen under 2.6.20.5. Using "-T permissive" works:
<==================== cut ====================>
smartctl version 5.37 [x86_64-unknown-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Maxtor DiamondMax 10 family (ATA/133 and SATA/150)
Device Model: Maxtor 6B250S0
Serial Number: XXXXXXXX
Firmware Version: BANC1G10
User Capacity: 251,000,193,024 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Wed Aug 15 12:01:47 2007 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
Error SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
CMD=0x50
FR =0x00
NS =0x00
SC =0x00
CL =0xc2
CH =0x00
SEL=0x00
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x05) Offline data collection activity
was aborted by an interrupting command from host.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (1922) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 99) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
3 Spin_Up_Time 0x0027 185 183 063 Pre-fail Always - 14093
4 Start_Stop_Count 0x0032 253 253 000 Old_age Always - 1050
5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail Always - 0
6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail Offline - 0
7 Seek_Error_Rate 0x000a 253 252 000 Old_age Always - 0
8 Seek_Time_Performance 0x0027 247 239 187 Pre-fail Always - 33104
9 Power_On_Minutes 0x0032 246 246 000 Old_age Always - 440h+23m
10 Spin_Retry_Count 0x002b 253 252 157 Pre-fail Always - 0
11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 251 251 000 Old_age Always - 1057
192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age Always - 0
193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always - 0
194 Temperature_Celsius 0x0032 035 253 000 Old_age Always - 38
195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always - 8387
196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline - 0
197 Current_Pending_Sector 0x0008 253 253 000 Old_age Offline - 0
198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0008 199 199 000 Old_age Offline - 0
200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always - 0
201 Soft_Read_Error_Rate 0x000a 253 252 000 Old_age Always - 0
202 TA_Increase_Count 0x000a 253 252 000 Old_age Always - 0
203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always - 0
204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age Always - 0
205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age Always - 0
207 Spin_High_Current 0x002a 253 252 000 Old_age Always - 0
208 Spin_Buzz 0x002a 253 252 000 Old_age Always - 0
209 Offline_Seek_Performnce 0x0024 234 234 000 Old_age Offline - 230
210 Unknown_Attribute 0x0032 253 252 000 Old_age Always - 0
211 Unknown_Attribute 0x0032 253 252 000 Old_age Always - 0
212 Unknown_Attribute 0x0032 253 252 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 2618 -
# 2 Short offline Completed without error 00% 2600 -
# 3 Short offline Completed without error 00% 2574 -
# 4 Short offline Self-test routine in progress 80% 2574 -
# 5 Short offline Completed without error 00% 2565 -
# 6 Short offline Completed without error 00% 2556 -
# 7 Short offline Completed without error 00% 2550 -
# 8 Extended offline Aborted by host 40% 2550 -
# 9 Short offline Completed without error 00% 2525 -
#10 Short offline Completed without error 00% 2516 -
#11 Short offline Completed without error 00% 2516 -
#12 Short offline Completed without error 00% 2504 -
#13 Short offline Completed without error 00% 2499 -
#14 Short offline Completed without error 00% 2494 -
#15 Short offline Completed without error 00% 2489 -
#16 Short offline Completed without error 00% 2484 -
#17 Short offline Completed without error 00% 2469 -
#18 Short offline Completed without error 00% 2450 -
#19 Short offline Completed without error 00% 2442 -
#20 Short offline Completed without error 00% 2435 -
#21 Short offline Completed without error 00% 2422 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
<==================== cut ====================>
Doing "smartctl -d ata -s on /dev/sd[cd]" or "smartctl -d ata -a
/dev/sd[cd]" works _most of the time_, but sometimes I get errors like
this:
<==================== cut ====================>
smartctl version 5.37 [x86_64-unknown-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint P120 series
Device Model: SAMSUNG SP2504C
Serial Number: XXXXXXXXXXXXXX
Firmware Version: VT100-33
User Capacity: 250,059,350,016 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 4a
Local Time is: Wed Aug 15 11:37:35 2007 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
Error SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
CMD=0x50
FR =0x00
NS =0x00
SC =0x49
CL =0x41
CH =0x16
SEL=0x00
A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options.
<==================== cut ====================>
This error is infrequent and not deterministic; I got it 2 times in
about 15-20 tries (I think the second time the SC/CL/CH values were
different but I did not manage to capture that).
When the smart command succeeds, I get the following output:
<==================== cut ====================>
smartctl version 5.37 [x86_64-unknown-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint P120 series
Device Model: SAMSUNG SP2504C
Serial Number: XXXXXXXXXXXXXX
Firmware Version: VT100-33
User Capacity: 250,059,350,016 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 4a
Local Time is: Wed Aug 15 11:47:00 2007 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (4867) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 81) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0007 100 100 025 Pre-fail Always - 6080
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 817
5 Reallocated_Sector_Ct 0x0033 253 253 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 253 253 051 Pre-fail Always - 0
8 Seek_Time_Performance 0x0025 253 253 015 Pre-fail Offline - 11557
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 2342
10 Spin_Retry_Count 0x0033 253 253 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0012 253 002 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 783
190 Temperature_Celsius 0x0022 148 124 000 Old_age Always - 30
194 Temperature_Celsius 0x0022 148 124 000 Old_age Always - 30
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 2820219
196 Reallocated_Event_Count 0x0032 253 253 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 253 253 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 253 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age Always - 0
201 Soft_Read_Error_Rate 0x000a 253 100 000 Old_age Always - 0
202 TA_Increase_Count 0x0032 253 253 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 2336 -
# 2 Short offline Completed without error 00% 2318 -
# 3 Short offline Completed without error 00% 2292 -
# 4 Short offline Interrupted (host reset) 80% 2291 -
# 5 Short offline Completed without error 00% 2283 -
# 6 Short offline Completed without error 00% 2273 -
# 7 Short offline Completed without error 00% 2268 -
# 8 Short offline Completed without error 00% 2241 -
# 9 Short offline Completed without error 00% 2233 -
#10 Short offline Completed without error 00% 2233 -
#11 Short offline Completed without error 00% 2221 -
#12 Short offline Completed without error 00% 2216 -
#13 Short offline Completed without error 00% 2210 -
#14 Short offline Completed without error 00% 2206 -
#15 Short offline Completed without error 00% 2200 -
#16 Short offline Completed without error 00% 2185 -
#17 Extended offline Completed without error 00% 2181 -
#18 Short offline Completed without error 00% 2166 -
#19 Short offline Completed without error 00% 2158 -
#20 Extended offline Completed without error 00% 2155 -
#21 Short offline Completed without error 00% 2151 -
SMART Selective Self-Test Log Data Structure Revision Number (0) should be 1
SMART Selective self-test log data structure revision number 0
Warning: ATA Specification requires selective self-test log data structure revision number = 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
<==================== cut ====================>
The output for the other disk is nearly identical, the differences in
the reported values are insignificant.
SMART shows the same behavior regardless if ADMA is enabled or not, but
when booting with ADMA-enabled I got a SATA exception for sdc in about
10 minutes in single-user mode so basically no I/O load. I never got a
SATA exception with ADMA turned off even during heavy I/O load.
Gabor
--
---------------------------------------------------------
MTA SZTAKI Computer and Automation Research Institute
Hungarian Academy of Sciences
---------------------------------------------------------
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/