Re: 2.6.23-rc4-mm1

From: Andrew Morton
Date: Mon Sep 10 2007 - 14:21:23 EST

Next message: Paul E. McKenney: "[PATCH RFC 0/9] RCU: Preemptible RCU"
Previous message: Alistair John Strachan: "Re: [RESEND][PATCH 0/4] Virtual Machine Time Accounting"
In reply to: Andy Whitcroft: "Re: 2.6.23-rc4-mm1"
Next in thread: Torsten Kaiser: "Re: 2.6.23-rc4-mm1"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On Mon, 10 Sep 2007 18:49:26 +0100 Andy Whitcroft <apw@xxxxxxxxxxxx> wrote:

> I have a couple of old NUMA-Q systems which are unable to read their
> boot disks with 2.6.23-rc4-mm1. The disks appear to be recognised and
> even the partition tables read correctly, and then they go pop:
>
> qla1280: QLA1040 found on PCI bus 0, dev 10

cc's added.

> Clocksource tsc unstable (delta = 99922590 ns)
> Time: jiffies clocksource has been installed.
> scsi(0:0): Resetting SCSI BUS
> scsi0 : QLogic QLA1040 PCI to SCSI Host Adapter
> Firmware version: 7.65.06, Driver version 3.26
> scsi 0:0:0:0: Direct-Access IBM DGHS18X 0360 PQ: 0 ANSI: 3
> scsi(0:0:0:0): Sync: period 10, offset 12, Wide
> scsi 0:0:1:0: Direct-Access IBM OEM DCHS09X 5454 PQ: 0 ANSI: 2
> scsi(0:0:1:0): Sync: period 10, offset 12, Wide
> scsi 0:0:2:0: Direct-Access IBM OEM DCHS09X 5454 PQ: 0 ANSI: 2
> scsi(0:0:2:0): Sync: period 10, offset 12, Wide
> scsi 0:0:3:0: Direct-Access IBM OEM DCHS09X 5454 PQ: 0 ANSI: 2
> scsi(0:0:3:0): Sync: period 10, offset 12, Wide
> scsi 0:0:4:0: Direct-Access IBM OEM DCHS09X 5454 PQ: 0 ANSI: 2
> scsi(0:0:4:0): Sync: period 10, offset 12, Wide
> st: Version 20070203, fixed bufsize 32768, s/g segs 256
> sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA
> sd 0:0:0:0: [sda] 35843670 512-byte hardware sectors (18352 MB)
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA
> sda: sda1
> sd 0:0:0:0: [sda] Attached SCSI disk
> sd 0:0:1:0: [sdb] 17796077 512-byte hardware sectors (9112 MB)
> sd 0:0:1:0: [sdb] Write Protect is off
> sd 0:0:1:0: [sdb] Write cache: disabled, read cache: enabled, supports DPO and FUA
> sd 0:0:1:0: [sdb] 17796077 512-byte hardware sectors (9112 MB)
> sd 0:0:1:0: [sdb] Write Protect is off
> sd 0:0:1:0: [sdb] Write cache: disabled, read cache: enabled, supports DPO and FUA
> sdb: unknown partition table
> sd 0:0:1:0: [sdb] Attached SCSI disk
> sd 0:0:2:0: [sdc] 17796077 512-byte hardware sectors (9112 MB)
> sd 0:0:2:0: [sdc] Write Protect is off
> sd 0:0:2:0: [sdc] Write cache: disabled, read cache: enabled, supports DPO and FUA
> sd 0:0:2:0: [sdc] 17796077 512-byte hardware sectors (9112 MB)
> sd 0:0:2:0: [sdc] Write Protect is off
> sd 0:0:2:0: [sdc] Write cache: disabled, read cache: enabled, supports DPO and FUA
> sdc: sdc1
> sd 0:0:2:0: [sdc] Attached SCSI disk
> sd 0:0:3:0: [sdd] 17796077 512-byte hardware sectors (9112 MB)
> sd 0:0:3:0: [sdd] Write Protect is off
> sd 0:0:3:0: [sdd] Write cache: disabled, read cache: enabled, supports DPO and FUA
> sd 0:0:3:0: [sdd] 17796077 512-byte hardware sectors (9112 MB)
> sd 0:0:3:0: [sdd] Write Protect is off
> sd 0:0:3:0: [sdd] Write cache: disabled, read cache: enabled, supports DPO and FUA
> sdd: sdd1
> sd 0:0:3:0: [sdd] Attached SCSI disk
> sd 0:0:4:0: [sde] 17796077 512-byte hardware sectors (9112 MB)
> sd 0:0:4:0: [sde] Write Protect is off
> sd 0:0:4:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA
> sd 0:0:4:0: [sde] 17796077 512-byte hardware sectors (9112 MB)
> sd 0:0:4:0: [sde] Write Protect is off
> sd 0:0:4:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA
> sde: unknown partition table
> sd 0:0:4:0: [sde] Attached SCSI disk
> sd 0:0:0:0: Attached scsi generic sg0 type 0
> sd 0:0:1:0: Attached scsi generic sg1 type 0
> sd 0:0:2:0: Attached scsi generic sg2 type 0
> sd 0:0:3:0: Attached scsi generic sg3 type 0
> sd 0:0:4:0: Attached scsi generic sg4 type 0
> serio: i8042 KBD port at 0x60,0x64 irq 1
> serio: i8042 AUX port at 0x60,0x64 irq 12
> mice: PS/2 mouse device common for all mice
> input: AT Translated Set 2 keyboard as /class/input/input0
> oprofile: using NMI interrupt.
> TCP cubic registered
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> Using IPI Shortcut mode
> input: PS/2 Logitech Mouse as /class/input/input1
> RAMDISK: cramfs filesystem found at block 0
> RAMDISK: Loading 1244KiB [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/done.
> VFS: Mounted root (cramfs filesystem) readonly.
> Freeing unused kernel memory: 220k freed
> initrd-tools: 0.1.81.1
> mount: fs type devfs not supported by kernel
> FATAL: Module sd_mod not found.
> umount: devfs: not mounted
> ext3: No journal on filesystem on sda1
> sd 0:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
> end_request: I/O error, dev sda, sector 63
> Buffer I/O error on device sda1, logical block 0
> Buffer I/O error on device sda1, logical block 1
> Buffer I/O error on device sda1, logical block 2
> Buffer I/O error on device sda1, logical block 3
> mount: fs type devfs not supported by kernel
> ext3: No journal on filesystem on sda1
> umount: devfs: not mounted
> sd 0:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
> end_request: I/O error, dev sda, sector 28010831
> sd 0:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
> end_request: I/O error, dev sda, sector 31080815
> sd 0:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
> end_request: I/O error, dev sda, sector 31080855
> sd 0:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
> end_request: I/O error, dev sda, sector 31080919
> Buffer I/O error on device sda1, logical block 3885107
> sd 0:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
> end_request: I/O error, dev sda, sector 28411047
> sd 0:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
> end_request: I/O error, dev sda, sector 31135687
> sd 0:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
> end_request: I/O error, dev sda, sector 31138007
> sd 0:0:0:0: [sda] <6>sd 0:0:0:0: [sda] Result: hostbyte=0x07 driverbyte=0x00
>

The only patch which touches qla1280 is git-block.patch. From a quick
squizz the change looks OK, although it's tricky and something might have
broken.

(the dprintk at line 2929 needs to print remseg, not seg_cnt).

Can you retest with that change reverted (below)? If it's not that then
perhaps something in scsi core broke, dunno.

diff -puN drivers/scsi/qla1280.c~revert-1 drivers/scsi/qla1280.c
--- a/drivers/scsi/qla1280.c~revert-1
+++ a/drivers/scsi/qla1280.c
@@ -2775,7 +2775,7 @@ qla1280_64bit_start_scsi(struct scsi_qla
struct device_reg __iomem *reg = ha->iobase;
struct scsi_cmnd *cmd = sp->cmd;
cmd_a64_entry_t *pkt;
- struct scatterlist *sg = NULL, *s;
+ struct scatterlist *sg = NULL;
__le32 *dword_ptr;
dma_addr_t dma_handle;
int status = 0;
@@ -2889,16 +2889,13 @@ qla1280_64bit_start_scsi(struct scsi_qla
* Load data segments.
*/
if (seg_cnt) { /* If data transfer. */
- int remseg = seg_cnt;
/* Setup packet address segment pointer. */
dword_ptr = (u32 *)&pkt->dseg_0_address;

if (cmd->use_sg) { /* If scatter gather */
/* Load command entry data segments. */
- for_each_sg(sg, s, seg_cnt, cnt) {
- if (cnt == 2)
- break;
- dma_handle = sg_dma_address(s);
+ for (cnt = 0; cnt < 2 && seg_cnt; cnt++, seg_cnt--) {
+ dma_handle = sg_dma_address(sg);
#if defined(CONFIG_IA64_GENERIC) || defined(CONFIG_IA64_SGI_SN2)
if (ha->flags.use_pci_vchannel)
sn_pci_set_vchan(ha->pdev,
@@ -2909,12 +2906,12 @@ qla1280_64bit_start_scsi(struct scsi_qla
cpu_to_le32(pci_dma_lo32(dma_handle));
*dword_ptr++ =
cpu_to_le32(pci_dma_hi32(dma_handle));
- *dword_ptr++ = cpu_to_le32(sg_dma_len(s));
+ *dword_ptr++ = cpu_to_le32(sg_dma_len(sg));
+ sg++;
dprintk(3, "S/G Segment phys_addr=%x %x, len=0x%x\n",
cpu_to_le32(pci_dma_hi32(dma_handle)),
cpu_to_le32(pci_dma_lo32(dma_handle)),
- cpu_to_le32(sg_dma_len(sg_next(s))));
- remseg--;
+ cpu_to_le32(sg_dma_len(sg)));
}
dprintk(5, "qla1280_64bit_start_scsi: Scatter/gather "
"command packet data - b %i, t %i, l %i \n",
@@ -2929,9 +2926,7 @@ qla1280_64bit_start_scsi(struct scsi_qla
dprintk(3, "S/G Building Continuation...seg_cnt=0x%x "
"remains\n", seg_cnt);

- while (remseg > 0) {
- /* Update sg start */
- sg = s;
+ while (seg_cnt > 0) {
/* Adjust ring index. */
ha->req_ring_index++;
if (ha->req_ring_index == REQUEST_ENTRY_CNT) {
@@ -2957,10 +2952,9 @@ qla1280_64bit_start_scsi(struct scsi_qla
(u32 *)&((struct cont_a64_entry *) pkt)->dseg_0_address;

/* Load continuation entry data segments. */
- for_each_sg(sg, s, remseg, cnt) {
- if (cnt == 5)
- break;
- dma_handle = sg_dma_address(s);
+ for (cnt = 0; cnt < 5 && seg_cnt;
+ cnt++, seg_cnt--) {
+ dma_handle = sg_dma_address(sg);
#if defined(CONFIG_IA64_GENERIC) || defined(CONFIG_IA64_SGI_SN2)
if (ha->flags.use_pci_vchannel)
sn_pci_set_vchan(ha->pdev,
@@ -2972,12 +2966,12 @@ qla1280_64bit_start_scsi(struct scsi_qla
*dword_ptr++ =
cpu_to_le32(pci_dma_hi32(dma_handle));
*dword_ptr++ =
- cpu_to_le32(sg_dma_len(s));
+ cpu_to_le32(sg_dma_len(sg));
dprintk(3, "S/G Segment Cont. phys_addr=%x %x, len=0x%x\n",
cpu_to_le32(pci_dma_hi32(dma_handle)),
cpu_to_le32(pci_dma_lo32(dma_handle)),
- cpu_to_le32(sg_dma_len(s)));
- remseg--;
+ cpu_to_le32(sg_dma_len(sg)));
+ sg++;
}
dprintk(5, "qla1280_64bit_start_scsi: "
"continuation packet data - b %i, t "
@@ -3068,7 +3062,7 @@ qla1280_32bit_start_scsi(struct scsi_qla
struct device_reg __iomem *reg = ha->iobase;
struct scsi_cmnd *cmd = sp->cmd;
struct cmd_entry *pkt;
- struct scatterlist *sg = NULL, *s;
+ struct scatterlist *sg = NULL;
__le32 *dword_ptr;
int status = 0;
int cnt;
@@ -3194,7 +3188,6 @@ qla1280_32bit_start_scsi(struct scsi_qla
* Load data segments.
*/
if (seg_cnt) {
- int remseg = seg_cnt;
/* Setup packet address segment pointer. */
dword_ptr = &pkt->dseg_0_address;

@@ -3203,25 +3196,22 @@ qla1280_32bit_start_scsi(struct scsi_qla
qla1280_dump_buffer(1, (char *)sg, 4 * 16);

/* Load command entry data segments. */
- for_each_sg(sg, s, seg_cnt, cnt) {
- if (cnt == 4)
- break;
+ for (cnt = 0; cnt < 4 && seg_cnt; cnt++, seg_cnt--) {
*dword_ptr++ =
- cpu_to_le32(pci_dma_lo32(sg_dma_address(s)));
- *dword_ptr++ = cpu_to_le32(sg_dma_len(s));
+ cpu_to_le32(pci_dma_lo32(sg_dma_address(sg)));
+ *dword_ptr++ =
+ cpu_to_le32(sg_dma_len(sg));
dprintk(3, "S/G Segment phys_addr=0x%lx, len=0x%x\n",
- (pci_dma_lo32(sg_dma_address(s))),
- (sg_dma_len(s)));
- remseg--;
+ (pci_dma_lo32(sg_dma_address(sg))),
+ (sg_dma_len(sg)));
+ sg++;
}
/*
* Build continuation packets.
*/
dprintk(3, "S/G Building Continuation"
"...seg_cnt=0x%x remains\n", seg_cnt);
- while (remseg > 0) {
- /* Continue from end point */
- sg = s;
+ while (seg_cnt > 0) {
/* Adjust ring index. */
ha->req_ring_index++;
if (ha->req_ring_index == REQUEST_ENTRY_CNT) {
@@ -3249,16 +3239,18 @@ qla1280_32bit_start_scsi(struct scsi_qla
&((struct cont_entry *) pkt)->dseg_0_address;

/* Load continuation entry data segments. */
- for_each_sg(sg, s, remseg, cnt) {
+ for (cnt = 0; cnt < 7 && seg_cnt;
+ cnt++, seg_cnt--) {
*dword_ptr++ =
- cpu_to_le32(pci_dma_lo32(sg_dma_address(s)));
+ cpu_to_le32(pci_dma_lo32(sg_dma_address(sg)));
*dword_ptr++ =
- cpu_to_le32(sg_dma_len(s));
+ cpu_to_le32(sg_dma_len(sg));
dprintk(1,
"S/G Segment Cont. phys_addr=0x%x, "
"len=0x%x\n",
- cpu_to_le32(pci_dma_lo32(sg_dma_address(s))),
- cpu_to_le32(sg_dma_len(s)));
+ cpu_to_le32(pci_dma_lo32(sg_dma_address(sg))),
+ cpu_to_le32(sg_dma_len(sg)));
+ sg++;
}
dprintk(5, "qla1280_32bit_start_scsi: "
"continuation packet data - "
_

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Next message: Paul E. McKenney: "[PATCH RFC 0/9] RCU: Preemptible RCU"
Previous message: Alistair John Strachan: "Re: [RESEND][PATCH 0/4] Virtual Machine Time Accounting"
In reply to: Andy Whitcroft: "Re: 2.6.23-rc4-mm1"
Next in thread: Torsten Kaiser: "Re: 2.6.23-rc4-mm1"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]