Re: [RFC] [PATCH -mm] ASIC3 driver
From: Samuel Ortiz
Date: Fri Oct 19 2007 - 06:53:20 EST
On Thu, Oct 18, 2007 at 03:05:44PM -0700, Andrew Morton wrote:
> On Thu, 18 Oct 2007 11:12:41 +0200
> Samuel Ortiz <sameo@xxxxxxxxxxxxxx> wrote:
> You're not a big fan of checkpatch, I see.
Well, now I am :-)
I fixed all the errors, there are only a couple lines being more than 80
characters left.
> > +#include <linux/module.h>
> > +#include <linux/version.h>
> > +#include <linux/irq.h>
>
> Please see the large comment at the top of linux/irq.h. I believe this
> driver will fial to compile on at least arm.
It doesn't build as a module, since we need the irq.h symbols.
I changed MFD_ASIC3 to bool. I somehow feel that this is not the cleanest
solution, but OTOH I think that dynamically adding IRQs and GPIOs to an
embedded board doesn't make much sense.
> We really should fix this.
As I explained to Thomas, asic3 defines an additional range of IRQs for the
board, so we really need to access the irq API.
There may be another way, but I'm not aware of it.
> > +static inline void asic3_write_register(struct asic3 *asic,
> > + unsigned int reg, u32 value)
> > +{
> > + iowrite16(value, (unsigned long)asic->mapping +
> > + (reg >> (2 - asic->bus_shift)));
> > +}
> > +
> > +static inline u32 asic3_read_register(struct asic3 *asic,
> > + unsigned int reg)
> > +{
> > + return ioread16((unsigned long)asic->mapping +
> > + (reg >> (2 - asic->bus_shift)));
> > +}
>
> You'd get faster code if that "2 - asic->bus_shift" was cached in struct
> asic3 rather than recalculated each time.
Done.
> > +static void asic3_irq_demux(unsigned int irq, struct irq_desc *desc)
> > +{
> > + int iter, i;
> > + struct asic3 *asic;
> > +
> > + desc->chip->ack(irq);
>
> hm, so this delves into the innards of the IRQ management. Does it work OK
> with and without CONFIG_GENERIC_HARDIRQS? If not, some Kconfig work will
> be needed.
It needs CONFIG_GENERIC_HARDIRQS, I fixed Kconfig.
> > + for (i = 0; i < ASIC3_GPIOS_PER_BANK; i++) {
> > + int bit = (1 << i);
> > + unsigned int irqnr;
> > + if (!(istat & bit))
> > + continue;
>
> Most people prefer a blank line between end-of-definitions and start-of-code.
Done.
> > +static void asic3_unmask_gpio_irq(unsigned int irq)
> > +{
> > + struct asic3 *asic = get_irq_chip_data(irq);
> > + u32 val, bank, index;
> > +
> > + bank = asic3_irq_to_bank(asic, irq);
> > + index = asic3_irq_to_index(asic, irq);
> > +
> > + spin_lock(&asic->lock);
> > + val = asic3_read_register(asic, bank + ASIC3_GPIO_Mask);
> > + val &= ~(1 << index);
> > + asic3_write_register(asic, bank + ASIC3_GPIO_Mask, val);
> > + spin_unlock(&asic->lock);
> > +}
>
> Am wondering about the handling of asic->lock. As it is taken from hard
> interrupts, it is a bug to take it with local interrupts enabled. afacit
> that is what this code is doing and is hence deadlockable. But I didn't
> look very hard.
No, I think you're right, the lock should be taken with local interrupts
disabled. I fixed that too.
> Has this code been exercised with lockdep enabled?
Yes, I'm running it with lockdep enabled.
> > +int asic3_gpio_get_value(struct asic3 *asic, unsigned gpio)
> > +{
> > + u32 mask = ASIC3_GPIO_bit(gpio);
> > +
> > + switch (gpio >> 4) {
> > + case ASIC3_GPIO_BANK_A:
> > + return asic3_get_gpio_a(asic, Status) & mask;
> > + case ASIC3_GPIO_BANK_B:
> > + return asic3_get_gpio_b(asic, Status) & mask;
> > + case ASIC3_GPIO_BANK_C:
> > + return asic3_get_gpio_c(asic, Status) & mask;
> > + case ASIC3_GPIO_BANK_D:
> > + return asic3_get_gpio_d(asic, Status) & mask;
> > + default:
> > + printk(KERN_ERR "%s: invalid GPIO value 0x%x",
> > + __FUNCTION__, gpio);
> > + return -EINVAL;
> > + }
> > +}
> > +EXPORT_SYMBOL(asic3_gpio_get_value);
> > ...
> > +EXPORT_SYMBOL(asic3_gpio_set_value);
>
> To what are these exported?
Currently nothing, but the plan is to push several drivers (leds, MMC,
buttons...) based on the ASIC3, and they need to access the ASIC3 GPIOs.
Do you want me to remove the EXPORT_SYMBOL until we actually add those
drivers ?
Thanks a lot for the review, here goes a new version of this patch:
Signed-off-by: Samuel Ortiz <sameo@xxxxxxxxxxxxxx>
---
drivers/mfd/Kconfig | 7
drivers/mfd/Makefile | 1
drivers/mfd/asic3.c | 588 ++++++++++++++++++++++++++++++++++++++++++++++
include/linux/mfd/asic3.h | 497 ++++++++++++++++++++++++++++++++++++++
4 files changed, 1093 insertions(+)
Index: linux-2.6-htc/drivers/mfd/asic3.c
===================================================================
--- /dev/null 1970-01-01 00:00:00.000000000 +0000
+++ linux-2.6-htc/drivers/mfd/asic3.c 2007-10-19 12:45:56.000000000 +0200
@@ -0,0 +1,588 @@
+/*
+ * driver/mfd/asic3.c
+ *
+ * Compaq ASIC3 support.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Copyright 2001 Compaq Computer Corporation.
+ * Copyright 2004-2005 Phil Blundell
+ * Copyright 2007 OpenedHand Ltd.
+ *
+ * Authors: Phil Blundell <pb@xxxxxxxxxxxxx>,
+ * Samuel Ortiz <sameo@xxxxxxxxxxxxxx>
+ *
+ */
+
+#include <linux/version.h>
+#include <linux/kernel.h>
+#include <linux/irq.h>
+#include <linux/io.h>
+#include <linux/spinlock.h>
+#include <linux/platform_device.h>
+
+#include <linux/mfd/asic3.h>
+
+static inline void asic3_write_register(struct asic3 *asic,
+ unsigned int reg, u32 value)
+{
+ iowrite16(value, (unsigned long)asic->mapping +
+ (reg >> asic->bus_shift));
+}
+
+static inline u32 asic3_read_register(struct asic3 *asic,
+ unsigned int reg)
+{
+ return ioread16((unsigned long)asic->mapping +
+ (reg >> asic->bus_shift));
+}
+
+/* IRQs */
+#define MAX_ASIC_ISR_LOOPS 20
+#define ASIC3_GPIO_Base_INCR \
+ (ASIC3_GPIO_B_Base - ASIC3_GPIO_A_Base)
+
+static void asic3_irq_flip_edge(struct asic3 *asic,
+ u32 base, int bit)
+{
+ u16 edge;
+ unsigned long flags;
+
+ spin_lock_irqsave(&asic->lock, flags);
+ edge = asic3_read_register(asic,
+ base + ASIC3_GPIO_EdgeTrigger);
+ edge ^= bit;
+ asic3_write_register(asic,
+ base + ASIC3_GPIO_EdgeTrigger, edge);
+ spin_unlock_irqrestore(&asic->lock, flags);
+}
+
+static void asic3_irq_demux(unsigned int irq, struct irq_desc *desc)
+{
+ int iter, i;
+ unsigned long flags;
+ struct asic3 *asic;
+
+ desc->chip->ack(irq);
+
+ asic = desc->handler_data;
+
+ for (iter = 0 ; iter < MAX_ASIC_ISR_LOOPS; iter++) {
+ u32 status;
+ int bank;
+
+ spin_lock_irqsave(&asic->lock, flags);
+ status = asic3_read_register(asic,
+ ASIC3_OFFSET(INTR, PIntStat));
+ spin_unlock_irqrestore(&asic->lock, flags);
+
+ /* Check all ten register bits */
+ if ((status & 0x3ff) == 0)
+ break;
+
+ /* Handle GPIO IRQs */
+ for (bank = 0; bank < ASIC3_NUM_GPIO_BANKS; bank++) {
+ if (status & (1 << bank)) {
+ unsigned long base, istat;
+
+ base = ASIC3_GPIO_A_Base
+ + bank * ASIC3_GPIO_Base_INCR;
+
+ spin_lock_irqsave(&asic->lock, flags);
+ istat = asic3_read_register(asic,
+ base +
+ ASIC3_GPIO_IntStatus);
+ /* Clearing IntStatus */
+ asic3_write_register(asic,
+ base +
+ ASIC3_GPIO_IntStatus, 0);
+ spin_unlock_irqrestore(&asic->lock, flags);
+
+ for (i = 0; i < ASIC3_GPIOS_PER_BANK; i++) {
+ int bit = (1 << i);
+ unsigned int irqnr;
+
+ if (!(istat & bit))
+ continue;
+
+ irqnr = asic->irq_base +
+ (ASIC3_GPIOS_PER_BANK * bank)
+ + i;
+ desc = irq_desc + irqnr;
+ desc->handle_irq(irqnr, desc);
+ if (asic->irq_bothedge[bank] & bit)
+ asic3_irq_flip_edge(asic, base,
+ bit);
+ }
+ }
+ }
+
+ /* Handle remaining IRQs in the status register */
+ for (i = ASIC3_NUM_GPIOS; i < ASIC3_NR_IRQS; i++) {
+ /* They start at bit 4 and go up */
+ if (status & (1 << (i - ASIC3_NUM_GPIOS + 4))) {
+ desc = irq_desc + + i;
+ desc->handle_irq(asic->irq_base + i,
+ desc);
+ }
+ }
+ }
+
+ if (iter >= MAX_ASIC_ISR_LOOPS)
+ printk(KERN_ERR "%s: interrupt processing overrun\n",
+ __FUNCTION__);
+}
+
+static inline int asic3_irq_to_bank(struct asic3 *asic, int irq)
+{
+ int n;
+
+ n = (irq - asic->irq_base) >> 4;
+
+ return (n * (ASIC3_GPIO_B_Base - ASIC3_GPIO_A_Base));
+}
+
+static inline int asic3_irq_to_index(struct asic3 *asic, int irq)
+{
+ return (irq - asic->irq_base) & 0xf;
+}
+
+static void asic3_mask_gpio_irq(unsigned int irq)
+{
+ struct asic3 *asic = get_irq_chip_data(irq);
+ u32 val, bank, index;
+ unsigned long flags;
+
+ bank = asic3_irq_to_bank(asic, irq);
+ index = asic3_irq_to_index(asic, irq);
+
+ spin_lock_irqsave(&asic->lock, flags);
+ val = asic3_read_register(asic, bank + ASIC3_GPIO_Mask);
+ val |= 1 << index;
+ asic3_write_register(asic, bank + ASIC3_GPIO_Mask, val);
+ spin_unlock_irqrestore(&asic->lock, flags);
+}
+
+static void asic3_mask_irq(unsigned int irq)
+{
+ struct asic3 *asic = get_irq_chip_data(irq);
+ int regval;
+ unsigned long flags;
+
+ spin_lock_irqsave(&asic->lock, flags);
+ regval = asic3_read_register(asic,
+ ASIC3_INTR_Base +
+ ASIC3_INTR_IntMask);
+
+ regval &= ~(ASIC3_INTMASK_MASK0 <<
+ (irq - (asic->irq_base + ASIC3_NUM_GPIOS)));
+
+ asic3_write_register(asic,
+ ASIC3_INTR_Base +
+ ASIC3_INTR_IntMask,
+ regval);
+ spin_unlock_irqrestore(&asic->lock, flags);
+}
+
+static void asic3_unmask_gpio_irq(unsigned int irq)
+{
+ struct asic3 *asic = get_irq_chip_data(irq);
+ u32 val, bank, index;
+ unsigned long flags;
+
+ bank = asic3_irq_to_bank(asic, irq);
+ index = asic3_irq_to_index(asic, irq);
+
+ spin_lock_irqsave(&asic->lock, flags);
+ val = asic3_read_register(asic, bank + ASIC3_GPIO_Mask);
+ val &= ~(1 << index);
+ asic3_write_register(asic, bank + ASIC3_GPIO_Mask, val);
+ spin_unlock_irqrestore(&asic->lock, flags);
+}
+
+static void asic3_unmask_irq(unsigned int irq)
+{
+ struct asic3 *asic = get_irq_chip_data(irq);
+ int regval;
+ unsigned long flags;
+
+ spin_lock_irqsave(&asic->lock, flags);
+ regval = asic3_read_register(asic,
+ ASIC3_INTR_Base +
+ ASIC3_INTR_IntMask);
+
+ regval |= (ASIC3_INTMASK_MASK0 <<
+ (irq - (asic->irq_base + ASIC3_NUM_GPIOS)));
+
+ asic3_write_register(asic,
+ ASIC3_INTR_Base +
+ ASIC3_INTR_IntMask,
+ regval);
+ spin_unlock_irqrestore(&asic->lock, flags);
+}
+
+static int asic3_gpio_irq_type(unsigned int irq, unsigned int type)
+{
+ struct asic3 *asic = get_irq_chip_data(irq);
+ u32 bank, index;
+ u16 trigger, level, edge, bit;
+ unsigned long flags;
+
+ bank = asic3_irq_to_bank(asic, irq);
+ index = asic3_irq_to_index(asic, irq);
+ bit = 1<<index;
+
+ spin_lock_irqsave(&asic->lock, flags);
+ level = asic3_read_register(asic,
+ bank + ASIC3_GPIO_LevelTrigger);
+ edge = asic3_read_register(asic,
+ bank + ASIC3_GPIO_EdgeTrigger);
+ trigger = asic3_read_register(asic,
+ bank + ASIC3_GPIO_TriggerType);
+ asic->irq_bothedge[(irq - asic->irq_base) >> 4] &= ~bit;
+
+ if (type == IRQT_RISING) {
+ trigger |= bit;
+ edge |= bit;
+ } else if (type == IRQT_FALLING) {
+ trigger |= bit;
+ edge &= ~bit;
+ } else if (type == IRQT_BOTHEDGE) {
+ trigger |= bit;
+ if (asic3_gpio_get_value(asic, irq - asic->irq_base))
+ edge &= ~bit;
+ else
+ edge |= bit;
+ asic->irq_bothedge[(irq - asic->irq_base) >> 4] |= bit;
+ } else if (type == IRQT_LOW) {
+ trigger &= ~bit;
+ level &= ~bit;
+ } else if (type == IRQT_HIGH) {
+ trigger &= ~bit;
+ level |= bit;
+ } else {
+ /*
+ * if type == IRQT_NOEDGE, we should mask interrupts, but
+ * be careful to not unmask them if mask was also called.
+ * Probably need internal state for mask.
+ */
+ printk(KERN_NOTICE "asic3: irq type not changed.\n");
+ }
+ asic3_write_register(asic, bank + ASIC3_GPIO_LevelTrigger,
+ level);
+ asic3_write_register(asic, bank + ASIC3_GPIO_EdgeTrigger,
+ edge);
+ asic3_write_register(asic, bank + ASIC3_GPIO_TriggerType,
+ trigger);
+ spin_unlock_irqrestore(&asic->lock, flags);
+ return 0;
+}
+
+static struct irq_chip asic3_gpio_irq_chip = {
+ .name = "ASIC3-GPIO",
+ .ack = asic3_mask_gpio_irq,
+ .mask = asic3_mask_gpio_irq,
+ .unmask = asic3_unmask_gpio_irq,
+ .set_type = asic3_gpio_irq_type,
+};
+
+static struct irq_chip asic3_irq_chip = {
+ .name = "ASIC3",
+ .ack = asic3_mask_irq,
+ .mask = asic3_mask_irq,
+ .unmask = asic3_unmask_irq,
+};
+
+static int asic3_irq_probe(struct platform_device *pdev)
+{
+ struct asic3 *asic = platform_get_drvdata(pdev);
+ unsigned long clksel = 0;
+ unsigned int irq, irq_base;
+
+ asic->irq_nr = platform_get_irq(pdev, 0);
+ if (asic->irq_nr < 0)
+ return asic->irq_nr;
+
+ /* turn on clock to IRQ controller */
+ clksel |= CLOCK_SEL_CX;
+ asic3_write_register(asic, ASIC3_OFFSET(CLOCK, SEL),
+ clksel);
+
+ irq_base = asic->irq_base;
+
+ for (irq = irq_base; irq < irq_base + ASIC3_NR_IRQS; irq++) {
+ if (irq < asic->irq_base + ASIC3_NUM_GPIOS)
+ set_irq_chip(irq, &asic3_gpio_irq_chip);
+ else
+ set_irq_chip(irq, &asic3_irq_chip);
+
+ set_irq_chip_data(irq, asic);
+ set_irq_handler(irq, handle_level_irq);
+ set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
+ }
+
+ asic3_write_register(asic, ASIC3_OFFSET(INTR, IntMask),
+ ASIC3_INTMASK_GINTMASK);
+
+ set_irq_chained_handler(asic->irq_nr, asic3_irq_demux);
+ set_irq_type(asic->irq_nr, IRQT_RISING);
+ set_irq_data(asic->irq_nr, asic);
+
+ return 0;
+}
+
+static void asic3_irq_remove(struct platform_device *pdev)
+{
+ struct asic3 *asic = platform_get_drvdata(pdev);
+ unsigned int irq, irq_base;
+
+ irq_base = asic->irq_base;
+
+ for (irq = irq_base; irq < irq_base + ASIC3_NR_IRQS; irq++) {
+ set_irq_flags(irq, 0);
+ set_irq_handler(irq, NULL);
+ set_irq_chip(irq, NULL);
+ set_irq_chip_data(irq, NULL);
+ }
+ set_irq_chained_handler(asic->irq_nr, NULL);
+}
+
+/* GPIOs */
+static inline u32 asic3_get_gpio(struct asic3 *asic, unsigned int base,
+ unsigned int function)
+{
+ return asic3_read_register(asic, base + function);
+}
+
+static void asic3_set_gpio(struct asic3 *asic, unsigned int base,
+ unsigned int function, u32 bits, u32 val)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&asic->lock, flags);
+ val |= (asic3_read_register(asic, base + function) & ~bits);
+
+ asic3_write_register(asic, base + function, val);
+ spin_unlock_irqrestore(&asic->lock, flags);
+}
+
+#define asic3_get_gpio_a(asic, fn) \
+ asic3_get_gpio(asic, ASIC3_GPIO_A_Base, ASIC3_GPIO_##fn)
+#define asic3_get_gpio_b(asic, fn) \
+ asic3_get_gpio(asic, ASIC3_GPIO_B_Base, ASIC3_GPIO_##fn)
+#define asic3_get_gpio_c(asic, fn) \
+ asic3_get_gpio(asic, ASIC3_GPIO_C_Base, ASIC3_GPIO_##fn)
+#define asic3_get_gpio_d(asic, fn) \
+ asic3_get_gpio(asic, ASIC3_GPIO_D_Base, ASIC3_GPIO_##fn)
+
+#define asic3_set_gpio_a(asic, fn, bits, val) \
+ asic3_set_gpio(asic, ASIC3_GPIO_A_Base, ASIC3_GPIO_##fn, bits, val)
+#define asic3_set_gpio_b(asic, fn, bits, val) \
+ asic3_set_gpio(asic, ASIC3_GPIO_B_Base, ASIC3_GPIO_##fn, bits, val)
+#define asic3_set_gpio_c(asic, fn, bits, val) \
+ asic3_set_gpio(asic, ASIC3_GPIO_C_Base, ASIC3_GPIO_##fn, bits, val)
+#define asic3_set_gpio_d(asic, fn, bits, val) \
+ asic3_set_gpio(asic, ASIC3_GPIO_D_Base, ASIC3_GPIO_##fn, bits, val)
+
+#define asic3_set_gpio_banks(asic, fn, bits, pdata, field) \
+ do { \
+ asic3_set_gpio_a((asic), fn, (bits), (pdata)->gpio_a.field); \
+ asic3_set_gpio_b((asic), fn, (bits), (pdata)->gpio_b.field); \
+ asic3_set_gpio_c((asic), fn, (bits), (pdata)->gpio_c.field); \
+ asic3_set_gpio_d((asic), fn, (bits), (pdata)->gpio_d.field); \
+ } while (0)
+
+int asic3_gpio_get_value(struct asic3 *asic, unsigned gpio)
+{
+ u32 mask = ASIC3_GPIO_bit(gpio);
+
+ switch (gpio >> 4) {
+ case ASIC3_GPIO_BANK_A:
+ return asic3_get_gpio_a(asic, Status) & mask;
+ case ASIC3_GPIO_BANK_B:
+ return asic3_get_gpio_b(asic, Status) & mask;
+ case ASIC3_GPIO_BANK_C:
+ return asic3_get_gpio_c(asic, Status) & mask;
+ case ASIC3_GPIO_BANK_D:
+ return asic3_get_gpio_d(asic, Status) & mask;
+ default:
+ printk(KERN_ERR "%s: invalid GPIO value 0x%x",
+ __FUNCTION__, gpio);
+ return -EINVAL;
+ }
+}
+EXPORT_SYMBOL(asic3_gpio_get_value);
+
+void asic3_gpio_set_value(struct asic3 *asic, unsigned gpio, int val)
+{
+ u32 mask = ASIC3_GPIO_bit(gpio);
+ u32 bitval = 0;
+ if (val)
+ bitval = mask;
+
+ switch (gpio >> 4) {
+ case ASIC3_GPIO_BANK_A:
+ asic3_set_gpio_a(asic, Out, mask, bitval);
+ return;
+ case ASIC3_GPIO_BANK_B:
+ asic3_set_gpio_b(asic, Out, mask, bitval);
+ return;
+ case ASIC3_GPIO_BANK_C:
+ asic3_set_gpio_c(asic, Out, mask, bitval);
+ return;
+ case ASIC3_GPIO_BANK_D:
+ asic3_set_gpio_d(asic, Out, mask, bitval);
+ return;
+ default:
+ printk(KERN_ERR "%s: invalid GPIO value 0x%x",
+ __FUNCTION__, gpio);
+ return;
+ }
+}
+EXPORT_SYMBOL(asic3_gpio_set_value);
+
+static int asic3_gpio_probe(struct platform_device *pdev)
+{
+ struct asic3_platform_data *pdata = pdev->dev.platform_data;
+ struct asic3 *asic = platform_get_drvdata(pdev);
+
+ asic3_write_register(asic, ASIC3_GPIO_OFFSET(A, Mask), 0xffff);
+ asic3_write_register(asic, ASIC3_GPIO_OFFSET(B, Mask), 0xffff);
+ asic3_write_register(asic, ASIC3_GPIO_OFFSET(C, Mask), 0xffff);
+ asic3_write_register(asic, ASIC3_GPIO_OFFSET(D, Mask), 0xffff);
+
+ asic3_set_gpio_a(asic, SleepMask, 0xffff, 0xffff);
+ asic3_set_gpio_b(asic, SleepMask, 0xffff, 0xffff);
+ asic3_set_gpio_c(asic, SleepMask, 0xffff, 0xffff);
+ asic3_set_gpio_d(asic, SleepMask, 0xffff, 0xffff);
+
+ if (pdata) {
+ asic3_set_gpio_banks(asic, Out, 0xffff, pdata, init);
+ asic3_set_gpio_banks(asic, Direction, 0xffff, pdata, dir);
+ asic3_set_gpio_banks(asic, SleepMask, 0xffff, pdata,
+ sleep_mask);
+ asic3_set_gpio_banks(asic, SleepOut, 0xffff, pdata, sleep_out);
+ asic3_set_gpio_banks(asic, BattFaultOut, 0xffff, pdata,
+ batt_fault_out);
+ asic3_set_gpio_banks(asic, SleepConf, 0xffff, pdata,
+ sleep_conf);
+ asic3_set_gpio_banks(asic, AltFunction, 0xffff, pdata,
+ alt_function);
+ }
+
+ return 0;
+}
+
+static void asic3_gpio_remove(struct platform_device *pdev)
+{
+ return;
+}
+
+
+/* Core */
+static int asic3_probe(struct platform_device *pdev)
+{
+ struct asic3_platform_data *pdata = pdev->dev.platform_data;
+ struct asic3 *asic;
+ struct resource *mem;
+ unsigned long clksel;
+ int ret;
+
+ asic = kzalloc(sizeof(struct asic3), GFP_KERNEL);
+ if (!asic)
+ return -ENOMEM;
+
+ spin_lock_init(&asic->lock);
+ platform_set_drvdata(pdev, asic);
+ asic->dev = &pdev->dev;
+
+ mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!mem) {
+ ret = -ENOMEM;
+ printk(KERN_ERR "asic3: no MEM resource\n");
+ goto err_out_1;
+ }
+
+ asic->mapping = ioremap(mem->start, PAGE_SIZE);
+ if (!asic->mapping) {
+ ret = -ENOMEM;
+ printk(KERN_ERR "asic3: couldn't ioremap\n");
+ goto err_out_1;
+ }
+
+ asic->irq_base = pdata->irq_base;
+
+ if (pdata && pdata->bus_shift)
+ asic->bus_shift = 2 - pdata->bus_shift;
+ else
+ asic->bus_shift = 0;
+
+ clksel = 0;
+ asic3_write_register(asic, ASIC3_OFFSET(CLOCK, SEL), clksel);
+
+ ret = asic3_irq_probe(pdev);
+ if (ret < 0) {
+ printk(KERN_ERR "asic3: couldn't probe IRQs\n");
+ goto err_out_2;
+ }
+ asic3_gpio_probe(pdev);
+
+ if (pdata->children) {
+ int i;
+ for (i = 0; i < pdata->n_children; i++) {
+ pdata->children[i]->dev.parent = &pdev->dev;
+ platform_device_register(pdata->children[i]);
+ }
+ }
+
+ printk(KERN_INFO "ASIC3 Core driver\n");
+
+ return 0;
+
+ err_out_2:
+ iounmap(asic->mapping);
+ err_out_1:
+ kfree(asic);
+
+ return ret;
+}
+
+static int asic3_remove(struct platform_device *pdev)
+{
+ struct asic3 *asic = platform_get_drvdata(pdev);
+
+ asic3_gpio_remove(pdev);
+ asic3_irq_remove(pdev);
+
+ asic3_write_register(asic, ASIC3_OFFSET(CLOCK, SEL), 0);
+
+ iounmap(asic->mapping);
+
+ kfree(asic);
+
+ return 0;
+}
+
+static void asic3_shutdown(struct platform_device *pdev)
+{
+}
+
+static struct platform_driver asic3_device_driver = {
+ .driver = {
+ .name = "asic3",
+ },
+ .probe = asic3_probe,
+ .remove = __devexit_p(asic3_remove),
+ .shutdown = asic3_shutdown,
+};
+
+static int __init asic3_init(void)
+{
+ int retval = 0;
+ retval = platform_driver_register(&asic3_device_driver);
+ return retval;
+}
+
+subsys_initcall(asic3_init);
Index: linux-2.6-htc/drivers/mfd/Kconfig
===================================================================
--- linux-2.6-htc.orig/drivers/mfd/Kconfig 2007-10-19 01:25:23.000000000 +0200
+++ linux-2.6-htc/drivers/mfd/Kconfig 2007-10-19 12:30:13.000000000 +0200
@@ -15,6 +15,13 @@
interface. The device may be connected by PCI or local bus with
varying functions enabled.
+config MFD_ASIC3
+ bool "Support for Compaq ASIC3"
+ depends on GENERIC_HARDIRQS
+ ---help---
+ This driver supports the ASIC3 multifunction chip found on many
+ PDAs (mainly iPAQ and HTC based ones).
+
endmenu
menu "Multimedia Capabilities Port drivers"
Index: linux-2.6-htc/drivers/mfd/Makefile
===================================================================
--- linux-2.6-htc.orig/drivers/mfd/Makefile 2007-10-19 01:25:23.000000000 +0200
+++ linux-2.6-htc/drivers/mfd/Makefile 2007-10-19 01:26:22.000000000 +0200
@@ -3,6 +3,7 @@
#
obj-$(CONFIG_MFD_SM501) += sm501.o
+obj-$(CONFIG_MFD_ASIC3) += asic3.o
obj-$(CONFIG_MCP) += mcp-core.o
obj-$(CONFIG_MCP_SA11X0) += mcp-sa11x0.o
Index: linux-2.6-htc/include/linux/mfd/asic3.h
===================================================================
--- /dev/null 1970-01-01 00:00:00.000000000 +0000
+++ linux-2.6-htc/include/linux/mfd/asic3.h 2007-10-19 12:19:04.000000000 +0200
@@ -0,0 +1,497 @@
+/*
+ * include/linux/mfd/asic3.h
+ *
+ * Compaq ASIC3 headers.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Copyright 2001 Compaq Computer Corporation.
+ * Copyright 2007 OpendHand.
+ */
+
+#ifndef __ASIC3_H__
+#define __ASIC3_H__
+
+#include <linux/types.h>
+
+struct asic3 {
+ void __iomem *mapping;
+ unsigned int bus_shift;
+ unsigned int irq_nr;
+ unsigned int irq_base;
+ spinlock_t lock;
+ u16 irq_bothedge[4];
+ struct device *dev;
+};
+
+struct asic3_platform_data {
+ struct {
+ u32 dir;
+ u32 init;
+ u32 sleep_mask;
+ u32 sleep_out;
+ u32 batt_fault_out;
+ u32 sleep_conf;
+ u32 alt_function;
+ } gpio_a, gpio_b, gpio_c, gpio_d;
+
+ unsigned int bus_shift;
+
+ unsigned int irq_base;
+
+ struct platform_device **children;
+ unsigned int n_children;
+};
+
+int asic3_gpio_get_value(struct asic3 *asic, unsigned gpio);
+void asic3_gpio_set_value(struct asic3 *asic, unsigned gpio, int val);
+
+#define ASIC3_NUM_GPIO_BANKS 4
+#define ASIC3_GPIOS_PER_BANK 16
+#define ASIC3_NUM_GPIOS 64
+#define ASIC3_NR_IRQS ASIC3_NUM_GPIOS + 6
+
+#define ASIC3_GPIO_BANK_A 0
+#define ASIC3_GPIO_BANK_B 1
+#define ASIC3_GPIO_BANK_C 2
+#define ASIC3_GPIO_BANK_D 3
+
+#define ASIC3_GPIO(bank, gpio) \
+ ((ASIC3_GPIOS_PER_BANK * ASIC3_GPIO_BANK_##bank) + (gpio))
+#define ASIC3_GPIO_bit(gpio) (1 << (gpio & 0xf))
+/* All offsets below are specified with this address bus shift */
+#define ASIC3_DEFAULT_ADDR_SHIFT 2
+
+#define ASIC3_OFFSET(base, reg) (ASIC3_##base##_Base + ASIC3_##base##_##reg)
+#define ASIC3_GPIO_OFFSET(base, reg) \
+ (ASIC3_GPIO_##base##_Base + ASIC3_GPIO_##reg)
+
+#define ASIC3_GPIO_A_Base 0x0000
+#define ASIC3_GPIO_B_Base 0x0100
+#define ASIC3_GPIO_C_Base 0x0200
+#define ASIC3_GPIO_D_Base 0x0300
+
+#define ASIC3_GPIO_Mask 0x00 /* R/W 0:don't mask */
+#define ASIC3_GPIO_Direction 0x04 /* R/W 0:input */
+#define ASIC3_GPIO_Out 0x08 /* R/W 0:output low */
+#define ASIC3_GPIO_TriggerType 0x0c /* R/W 0:level */
+#define ASIC3_GPIO_EdgeTrigger 0x10 /* R/W 0:falling */
+#define ASIC3_GPIO_LevelTrigger 0x14 /* R/W 0:low level detect */
+#define ASIC3_GPIO_SleepMask 0x18 /* R/W 0:don't mask in sleep mode */
+#define ASIC3_GPIO_SleepOut 0x1c /* R/W level 0:low in sleep mode */
+#define ASIC3_GPIO_BattFaultOut 0x20 /* R/W level 0:low in batt_fault */
+#define ASIC3_GPIO_IntStatus 0x24 /* R/W 0:none, 1:detect */
+#define ASIC3_GPIO_AltFunction 0x28 /* R/W 1:LED register control */
+#define ASIC3_GPIO_SleepConf 0x2c /*
+ * R/W bit 1: autosleep
+ * 0: disable gposlpout in normal mode,
+ * enable gposlpout in sleep mode.
+ */
+#define ASIC3_GPIO_Status 0x30 /* R Pin status */
+
+#define ASIC3_SPI_Base 0x0400
+#define ASIC3_SPI_Control 0x0000
+#define ASIC3_SPI_TxData 0x0004
+#define ASIC3_SPI_RxData 0x0008
+#define ASIC3_SPI_Int 0x000c
+#define ASIC3_SPI_Status 0x0010
+
+#define SPI_CONTROL_SPR(clk) ((clk) & 0x0f) /* Clock rate */
+
+#define ASIC3_PWM_0_Base 0x0500
+#define ASIC3_PWM_1_Base 0x0600
+#define ASIC3_PWM_TimeBase 0x0000
+#define ASIC3_PWM_PeriodTime 0x0004
+#define ASIC3_PWM_DutyTime 0x0008
+
+#define PWM_TIMEBASE_VALUE(x) ((x)&0xf) /* Low 4 bits sets time base */
+#define PWM_TIMEBASE_ENABLE (1 << 4) /* Enable clock */
+
+#define ASIC3_LED_0_Base 0x0700
+#define ASIC3_LED_1_Base 0x0800
+#define ASIC3_LED_2_Base 0x0900
+#define ASIC3_LED_TimeBase 0x0000 /* R/W 7 bits */
+#define ASIC3_LED_PeriodTime 0x0004 /* R/W 12 bits */
+#define ASIC3_LED_DutyTime 0x0008 /* R/W 12 bits */
+#define ASIC3_LED_AutoStopCount 0x000c /* R/W 16 bits */
+
+/* LED TimeBase bits - match ASIC2 */
+#define LED_TBS 0x0f /* Low 4 bits sets time base, max = 13 */
+ /* Note: max = 5 on hx4700 */
+ /* 0: maximum time base */
+ /* 1: maximum time base / 2 */
+ /* n: maximum time base / 2^n */
+
+#define LED_EN (1 << 4) /* LED ON/OFF 0:off, 1:on */
+#define LED_AUTOSTOP (1 << 5) /* LED ON/OFF auto stop 0:disable, 1:enable */
+#define LED_ALWAYS (1 << 6) /* LED Interrupt Mask 0:No mask, 1:mask */
+
+#define ASIC3_CLOCK_Base 0x0A00
+#define ASIC3_CLOCK_CDEX 0x00
+#define ASIC3_CLOCK_SEL 0x04
+
+#define CLOCK_CDEX_SOURCE (1 << 0) /* 2 bits */
+#define CLOCK_CDEX_SOURCE0 (1 << 0)
+#define CLOCK_CDEX_SOURCE1 (1 << 1)
+#define CLOCK_CDEX_SPI (1 << 2)
+#define CLOCK_CDEX_OWM (1 << 3)
+#define CLOCK_CDEX_PWM0 (1 << 4)
+#define CLOCK_CDEX_PWM1 (1 << 5)
+#define CLOCK_CDEX_LED0 (1 << 6)
+#define CLOCK_CDEX_LED1 (1 << 7)
+#define CLOCK_CDEX_LED2 (1 << 8)
+
+/* Clocks settings: 1 for 24.576 MHz, 0 for 12.288Mhz */
+#define CLOCK_CDEX_SD_HOST (1 << 9) /* R/W: SD host clock source */
+#define CLOCK_CDEX_SD_BUS (1 << 10) /* R/W: SD bus clock source ctrl */
+#define CLOCK_CDEX_SMBUS (1 << 11)
+#define CLOCK_CDEX_CONTROL_CX (1 << 12)
+
+#define CLOCK_CDEX_EX0 (1 << 13) /* R/W: 32.768 kHz crystal */
+#define CLOCK_CDEX_EX1 (1 << 14) /* R/W: 24.576 MHz crystal */
+
+#define CLOCK_SEL_SD_HCLK_SEL (1 << 0) /* R/W: SDIO host clock select */
+#define CLOCK_SEL_SD_BCLK_SEL (1 << 1) /* R/W: SDIO bus clock select */
+
+/* R/W: INT clock source control (32.768 kHz) */
+#define CLOCK_SEL_CX (1 << 2)
+
+
+#define ASIC3_INTR_Base 0x0B00
+
+#define ASIC3_INTR_IntMask 0x00 /* Interrupt mask control */
+#define ASIC3_INTR_PIntStat 0x04 /* Peripheral interrupt status */
+#define ASIC3_INTR_IntCPS 0x08 /* Interrupt timer clock pre-scale */
+#define ASIC3_INTR_IntTBS 0x0c /* Interrupt timer set */
+
+#define ASIC3_INTMASK_GINTMASK (1 << 0) /* Global INTs mask 1:enable */
+#define ASIC3_INTMASK_GINTEL (1 << 1) /* 1: rising edge, 0: hi level */
+#define ASIC3_INTMASK_MASK0 (1 << 2)
+#define ASIC3_INTMASK_MASK1 (1 << 3)
+#define ASIC3_INTMASK_MASK2 (1 << 4)
+#define ASIC3_INTMASK_MASK3 (1 << 5)
+#define ASIC3_INTMASK_MASK4 (1 << 6)
+#define ASIC3_INTMASK_MASK5 (1 << 7)
+
+#define ASIC3_INTR_PERIPHERAL_A (1 << 0)
+#define ASIC3_INTR_PERIPHERAL_B (1 << 1)
+#define ASIC3_INTR_PERIPHERAL_C (1 << 2)
+#define ASIC3_INTR_PERIPHERAL_D (1 << 3)
+#define ASIC3_INTR_LED0 (1 << 4)
+#define ASIC3_INTR_LED1 (1 << 5)
+#define ASIC3_INTR_LED2 (1 << 6)
+#define ASIC3_INTR_SPI (1 << 7)
+#define ASIC3_INTR_SMBUS (1 << 8)
+#define ASIC3_INTR_OWM (1 << 9)
+
+#define ASIC3_INTR_CPS(x) ((x)&0x0f) /* 4 bits, max 14 */
+#define ASIC3_INTR_CPS_SET (1 << 4) /* Time base enable */
+
+
+/* Basic control of the SD ASIC */
+#define ASIC3_SDHWCTRL_Base 0x0E00
+#define ASIC3_SDHWCTRL_SDConf 0x00
+
+#define ASIC3_SDHWCTRL_SUSPEND (1 << 0) /* 1=suspend all SD operations */
+#define ASIC3_SDHWCTRL_CLKSEL (1 << 1) /* 1=SDICK, 0=HCLK */
+#define ASIC3_SDHWCTRL_PCLR (1 << 2) /* All registers of SDIO cleared */
+#define ASIC3_SDHWCTRL_LEVCD (1 << 3) /* SD card detection: 0:low */
+
+/* SD card write protection: 0=high */
+#define ASIC3_SDHWCTRL_LEVWP (1 << 4)
+#define ASIC3_SDHWCTRL_SDLED (1 << 5) /* SD card LED signal 0=disable */
+
+/* SD card power supply ctrl 1=enable */
+#define ASIC3_SDHWCTRL_SDPWR (1 << 6)
+
+#define ASIC3_EXTCF_Base 0x1100
+
+#define ASIC3_EXTCF_Select 0x00
+#define ASIC3_EXTCF_Reset 0x04
+
+#define ASIC3_EXTCF_SMOD0 (1 << 0) /* slot number of mode 0 */
+#define ASIC3_EXTCF_SMOD1 (1 << 1) /* slot number of mode 1 */
+#define ASIC3_EXTCF_SMOD2 (1 << 2) /* slot number of mode 2 */
+#define ASIC3_EXTCF_OWM_EN (1 << 4) /* enable onewire module */
+#define ASIC3_EXTCF_OWM_SMB (1 << 5) /* OWM bus selection */
+#define ASIC3_EXTCF_OWM_RESET (1 << 6) /* ?? used by OWM and CF */
+#define ASIC3_EXTCF_CF0_SLEEP_MODE (1 << 7) /* CF0 sleep state */
+#define ASIC3_EXTCF_CF1_SLEEP_MODE (1 << 8) /* CF1 sleep state */
+#define ASIC3_EXTCF_CF0_PWAIT_EN (1 << 10) /* CF0 PWAIT_n control */
+#define ASIC3_EXTCF_CF1_PWAIT_EN (1 << 11) /* CF1 PWAIT_n control */
+#define ASIC3_EXTCF_CF0_BUF_EN (1 << 12) /* CF0 buffer control */
+#define ASIC3_EXTCF_CF1_BUF_EN (1 << 13) /* CF1 buffer control */
+#define ASIC3_EXTCF_SD_MEM_ENABLE (1 << 14)
+#define ASIC3_EXTCF_CF_SLEEP (1 << 15) /* CF sleep mode control */
+
+/*********************************************
+ * The Onewire interface registers
+ *
+ * OWM_CMD
+ * OWM_DAT
+ * OWM_INTR
+ * OWM_INTEN
+ * OWM_CLKDIV
+ *
+ *********************************************/
+
+#define ASIC3_OWM_Base 0xC00
+
+#define ASIC3_OWM_CMD 0x00
+#define ASIC3_OWM_DAT 0x04
+#define ASIC3_OWM_INTR 0x08
+#define ASIC3_OWM_INTEN 0x0C
+#define ASIC3_OWM_CLKDIV 0x10
+
+#define ASIC3_OWM_CMD_ONEWR (1 << 0)
+#define ASIC3_OWM_CMD_SRA (1 << 1)
+#define ASIC3_OWM_CMD_DQO (1 << 2)
+#define ASIC3_OWM_CMD_DQI (1 << 3)
+
+#define ASIC3_OWM_INTR_PD (1 << 0)
+#define ASIC3_OWM_INTR_PDR (1 << 1)
+#define ASIC3_OWM_INTR_TBE (1 << 2)
+#define ASIC3_OWM_INTR_TEMP (1 << 3)
+#define ASIC3_OWM_INTR_RBF (1 << 4)
+
+#define ASIC3_OWM_INTEN_EPD (1 << 0)
+#define ASIC3_OWM_INTEN_IAS (1 << 1)
+#define ASIC3_OWM_INTEN_ETBE (1 << 2)
+#define ASIC3_OWM_INTEN_ETMT (1 << 3)
+#define ASIC3_OWM_INTEN_ERBF (1 << 4)
+
+#define ASIC3_OWM_CLKDIV_PRE (3 << 0) /* two bits wide at bit 0 */
+#define ASIC3_OWM_CLKDIV_DIV (7 << 2) /* 3 bits wide at bit 2 */
+
+
+/*****************************************************************************
+ * The SD configuration registers are at a completely different location
+ * in memory. They are divided into three sets of registers:
+ *
+ * SD_CONFIG Core configuration register
+ * SD_CTRL Control registers for SD operations
+ * SDIO_CTRL Control registers for SDIO operations
+ *
+ *****************************************************************************/
+#define ASIC3_SD_CONFIG_Base 0x0400 /* Assumes 32 bit addressing */
+
+#define ASIC3_SD_CONFIG_Command 0x08 /* R/W: Command */
+
+/* [0:8] SD Control Register Base Address */
+#define ASIC3_SD_CONFIG_Addr0 0x20
+
+/* [9:31] SD Control Register Base Address */
+#define ASIC3_SD_CONFIG_Addr1 0x24
+
+/* R/O: interrupt assigned to pin */
+#define ASIC3_SD_CONFIG_IntPin 0x78
+
+/*
+ * Set to 0x1f to clock SD controller, 0 otherwise.
+ * At 0x82 - Gated Clock Ctrl
+ */
+#define ASIC3_SD_CONFIG_ClkStop 0x80
+
+/* Control clock of SD controller */
+#define ASIC3_SD_CONFIG_ClockMode 0x84
+#define ASIC3_SD_CONFIG_SDHC_PinStatus 0x88 /* R/0: SD pins status */
+#define ASIC3_SD_CONFIG_SDHC_Power1 0x90 /* Power1 - manual pwr ctrl */
+
+/* auto power up after card inserted */
+#define ASIC3_SD_CONFIG_SDHC_Power2 0x92
+
+/* auto power down when card removed */
+#define ASIC3_SD_CONFIG_SDHC_Power3 0x94
+#define ASIC3_SD_CONFIG_SDHC_CardDetect 0x98
+#define ASIC3_SD_CONFIG_SDHC_Slot 0xA0 /* R/O: support slot number */
+#define ASIC3_SD_CONFIG_SDHC_ExtGateClk1 0x1E0 /* Not used */
+#define ASIC3_SD_CONFIG_SDHC_ExtGateClk2 0x1E2 /* Not used*/
+
+/* GPIO Output Reg. , at 0x1EA - GPIO Output Enable Reg. */
+#define ASIC3_SD_CONFIG_SDHC_GPIO_OutAndEnable 0x1E8
+#define ASIC3_SD_CONFIG_SDHC_GPIO_Status 0x1EC /* GPIO Status Reg. */
+
+/* Bit 1: double buffer/single buffer */
+#define ASIC3_SD_CONFIG_SDHC_ExtGateClk3 0x1F0
+
+/* Memory access enable (set to 1 to access SD Controller) */
+#define SD_CONFIG_COMMAND_MAE (1<<1)
+
+#define SD_CONFIG_CLK_ENABLE_ALL 0x1f
+
+#define SD_CONFIG_POWER1_PC_33V 0x0200 /* Set for 3.3 volts */
+#define SD_CONFIG_POWER1_PC_OFF 0x0000 /* Turn off power */
+
+ /* two bits - number of cycles for card detection */
+#define SD_CONFIG_CARDDETECTMODE_CLK ((x) & 0x3)
+
+
+#define ASIC3_SD_CTRL_Base 0x1000
+
+#define ASIC3_SD_CTRL_Cmd 0x00
+#define ASIC3_SD_CTRL_Arg0 0x08
+#define ASIC3_SD_CTRL_Arg1 0x0C
+#define ASIC3_SD_CTRL_StopInternal 0x10
+#define ASIC3_SD_CTRL_TransferSectorCount 0x14
+#define ASIC3_SD_CTRL_Response0 0x18
+#define ASIC3_SD_CTRL_Response1 0x1C
+#define ASIC3_SD_CTRL_Response2 0x20
+#define ASIC3_SD_CTRL_Response3 0x24
+#define ASIC3_SD_CTRL_Response4 0x28
+#define ASIC3_SD_CTRL_Response5 0x2C
+#define ASIC3_SD_CTRL_Response6 0x30
+#define ASIC3_SD_CTRL_Response7 0x34
+#define ASIC3_SD_CTRL_CardStatus 0x38
+#define ASIC3_SD_CTRL_BufferCtrl 0x3C
+#define ASIC3_SD_CTRL_IntMaskCard 0x40
+#define ASIC3_SD_CTRL_IntMaskBuffer 0x44
+#define ASIC3_SD_CTRL_CardClockCtrl 0x48
+#define ASIC3_SD_CTRL_MemCardXferDataLen 0x4C
+#define ASIC3_SD_CTRL_MemCardOptionSetup 0x50
+#define ASIC3_SD_CTRL_ErrorStatus0 0x58
+#define ASIC3_SD_CTRL_ErrorStatus1 0x5C
+#define ASIC3_SD_CTRL_DataPort 0x60
+#define ASIC3_SD_CTRL_TransactionCtrl 0x68
+#define ASIC3_SD_CTRL_SoftwareReset 0x1C0
+
+#define SD_CTRL_SOFTWARE_RESET_CLEAR (1<<0)
+
+#define SD_CTRL_TRANSACTIONCONTROL_SET (1<<8)
+
+#define SD_CTRL_CARDCLOCKCONTROL_FOR_SD_CARD (1<<15)
+#define SD_CTRL_CARDCLOCKCONTROL_ENABLE_CLOCK (1<<8)
+#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_512 (1<<7)
+#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_256 (1<<6)
+#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_128 (1<<5)
+#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_64 (1<<4)
+#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_32 (1<<3)
+#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_16 (1<<2)
+#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_8 (1<<1)
+#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_4 (1<<0)
+#define SD_CTRL_CARDCLOCKCONTROL_CLK_DIV_2 (0<<0)
+
+#define MEM_CARD_OPTION_REQUIRED 0x000e
+#define MEM_CARD_OPTION_DATA_RESPONSE_TIMEOUT(x) (((x) & 0x0f) << 4)
+#define MEM_CARD_OPTION_C2_MODULE_NOT_PRESENT (1<<14)
+#define MEM_CARD_OPTION_DATA_XFR_WIDTH_1 (1<<15)
+#define MEM_CARD_OPTION_DATA_XFR_WIDTH_4 0
+
+#define SD_CTRL_COMMAND_INDEX(x) ((x) & 0x3f)
+#define SD_CTRL_COMMAND_TYPE_CMD (0 << 6)
+#define SD_CTRL_COMMAND_TYPE_ACMD (1 << 6)
+#define SD_CTRL_COMMAND_TYPE_AUTHENTICATION (2 << 6)
+#define SD_CTRL_COMMAND_RESPONSE_TYPE_NORMAL (0 << 8)
+#define SD_CTRL_COMMAND_RESPONSE_TYPE_EXT_R1 (4 << 8)
+#define SD_CTRL_COMMAND_RESPONSE_TYPE_EXT_R1B (5 << 8)
+#define SD_CTRL_COMMAND_RESPONSE_TYPE_EXT_R2 (6 << 8)
+#define SD_CTRL_COMMAND_RESPONSE_TYPE_EXT_R3 (7 << 8)
+#define SD_CTRL_COMMAND_DATA_PRESENT (1 << 11)
+#define SD_CTRL_COMMAND_TRANSFER_READ (1 << 12)
+#define SD_CTRL_COMMAND_TRANSFER_WRITE (0 << 12)
+#define SD_CTRL_COMMAND_MULTI_BLOCK (1 << 13)
+#define SD_CTRL_COMMAND_SECURITY_CMD (1 << 14)
+
+#define SD_CTRL_STOP_INTERNAL_ISSSUE_CMD12 (1 << 0)
+#define SD_CTRL_STOP_INTERNAL_AUTO_ISSUE_CMD12 (1 << 8)
+
+#define SD_CTRL_CARDSTATUS_RESPONSE_END (1 << 0)
+#define SD_CTRL_CARDSTATUS_RW_END (1 << 2)
+#define SD_CTRL_CARDSTATUS_CARD_REMOVED_0 (1 << 3)
+#define SD_CTRL_CARDSTATUS_CARD_INSERTED_0 (1 << 4)
+#define SD_CTRL_CARDSTATUS_SIGNAL_STATE_PRESENT_0 (1 << 5)
+#define SD_CTRL_CARDSTATUS_WRITE_PROTECT (1 << 7)
+#define SD_CTRL_CARDSTATUS_CARD_REMOVED_3 (1 << 8)
+#define SD_CTRL_CARDSTATUS_CARD_INSERTED_3 (1 << 9)
+#define SD_CTRL_CARDSTATUS_SIGNAL_STATE_PRESENT_3 (1 << 10)
+
+#define SD_CTRL_BUFFERSTATUS_CMD_INDEX_ERROR (1 << 0)
+#define SD_CTRL_BUFFERSTATUS_CRC_ERROR (1 << 1)
+#define SD_CTRL_BUFFERSTATUS_STOP_BIT_END_ERROR (1 << 2)
+#define SD_CTRL_BUFFERSTATUS_DATA_TIMEOUT (1 << 3)
+#define SD_CTRL_BUFFERSTATUS_BUFFER_OVERFLOW (1 << 4)
+#define SD_CTRL_BUFFERSTATUS_BUFFER_UNDERFLOW (1 << 5)
+#define SD_CTRL_BUFFERSTATUS_CMD_TIMEOUT (1 << 6)
+#define SD_CTRL_BUFFERSTATUS_UNK7 (1 << 7)
+#define SD_CTRL_BUFFERSTATUS_BUFFER_READ_ENABLE (1 << 8)
+#define SD_CTRL_BUFFERSTATUS_BUFFER_WRITE_ENABLE (1 << 9)
+#define SD_CTRL_BUFFERSTATUS_ILLEGAL_FUNCTION (1 << 13)
+#define SD_CTRL_BUFFERSTATUS_CMD_BUSY (1 << 14)
+#define SD_CTRL_BUFFERSTATUS_ILLEGAL_ACCESS (1 << 15)
+
+#define SD_CTRL_INTMASKCARD_RESPONSE_END (1 << 0)
+#define SD_CTRL_INTMASKCARD_RW_END (1 << 2)
+#define SD_CTRL_INTMASKCARD_CARD_REMOVED_0 (1 << 3)
+#define SD_CTRL_INTMASKCARD_CARD_INSERTED_0 (1 << 4)
+#define SD_CTRL_INTMASKCARD_SIGNAL_STATE_PRESENT_0 (1 << 5)
+#define SD_CTRL_INTMASKCARD_UNK6 (1 << 6)
+#define SD_CTRL_INTMASKCARD_WRITE_PROTECT (1 << 7)
+#define SD_CTRL_INTMASKCARD_CARD_REMOVED_3 (1 << 8)
+#define SD_CTRL_INTMASKCARD_CARD_INSERTED_3 (1 << 9)
+#define SD_CTRL_INTMASKCARD_SIGNAL_STATE_PRESENT_3 (1 << 10)
+
+#define SD_CTRL_INTMASKBUFFER_CMD_INDEX_ERROR (1 << 0)
+#define SD_CTRL_INTMASKBUFFER_CRC_ERROR (1 << 1)
+#define SD_CTRL_INTMASKBUFFER_STOP_BIT_END_ERROR (1 << 2)
+#define SD_CTRL_INTMASKBUFFER_DATA_TIMEOUT (1 << 3)
+#define SD_CTRL_INTMASKBUFFER_BUFFER_OVERFLOW (1 << 4)
+#define SD_CTRL_INTMASKBUFFER_BUFFER_UNDERFLOW (1 << 5)
+#define SD_CTRL_INTMASKBUFFER_CMD_TIMEOUT (1 << 6)
+#define SD_CTRL_INTMASKBUFFER_UNK7 (1 << 7)
+#define SD_CTRL_INTMASKBUFFER_BUFFER_READ_ENABLE (1 << 8)
+#define SD_CTRL_INTMASKBUFFER_BUFFER_WRITE_ENABLE (1 << 9)
+#define SD_CTRL_INTMASKBUFFER_ILLEGAL_FUNCTION (1 << 13)
+#define SD_CTRL_INTMASKBUFFER_CMD_BUSY (1 << 14)
+#define SD_CTRL_INTMASKBUFFER_ILLEGAL_ACCESS (1 << 15)
+
+#define SD_CTRL_DETAIL0_RESPONSE_CMD_ERROR (1 << 0)
+#define SD_CTRL_DETAIL0_END_BIT_ERROR_FOR_RESPONSE_NON_CMD12 (1 << 2)
+#define SD_CTRL_DETAIL0_END_BIT_ERROR_FOR_RESPONSE_CMD12 (1 << 3)
+#define SD_CTRL_DETAIL0_END_BIT_ERROR_FOR_READ_DATA (1 << 4)
+#define SD_CTRL_DETAIL0_END_BIT_ERROR_FOR_WRITE_CRC_STATUS (1 << 5)
+#define SD_CTRL_DETAIL0_CRC_ERROR_FOR_RESPONSE_NON_CMD12 (1 << 8)
+#define SD_CTRL_DETAIL0_CRC_ERROR_FOR_RESPONSE_CMD12 (1 << 9)
+#define SD_CTRL_DETAIL0_CRC_ERROR_FOR_READ_DATA (1 << 10)
+#define SD_CTRL_DETAIL0_CRC_ERROR_FOR_WRITE_CMD (1 << 11)
+
+#define SD_CTRL_DETAIL1_NO_CMD_RESPONSE (1 << 0)
+#define SD_CTRL_DETAIL1_TIMEOUT_READ_DATA (1 << 4)
+#define SD_CTRL_DETAIL1_TIMEOUT_CRS_STATUS (1 << 5)
+#define SD_CTRL_DETAIL1_TIMEOUT_CRC_BUSY (1 << 6)
+
+#define ASIC3_SDIO_CTRL_Base 0x1200
+
+#define ASIC3_SDIO_CTRL_Cmd 0x00
+#define ASIC3_SDIO_CTRL_CardPortSel 0x04
+#define ASIC3_SDIO_CTRL_Arg0 0x08
+#define ASIC3_SDIO_CTRL_Arg1 0x0C
+#define ASIC3_SDIO_CTRL_TransferBlockCount 0x14
+#define ASIC3_SDIO_CTRL_Response0 0x18
+#define ASIC3_SDIO_CTRL_Response1 0x1C
+#define ASIC3_SDIO_CTRL_Response2 0x20
+#define ASIC3_SDIO_CTRL_Response3 0x24
+#define ASIC3_SDIO_CTRL_Response4 0x28
+#define ASIC3_SDIO_CTRL_Response5 0x2C
+#define ASIC3_SDIO_CTRL_Response6 0x30
+#define ASIC3_SDIO_CTRL_Response7 0x34
+#define ASIC3_SDIO_CTRL_CardStatus 0x38
+#define ASIC3_SDIO_CTRL_BufferCtrl 0x3C
+#define ASIC3_SDIO_CTRL_IntMaskCard 0x40
+#define ASIC3_SDIO_CTRL_IntMaskBuffer 0x44
+#define ASIC3_SDIO_CTRL_CardXferDataLen 0x4C
+#define ASIC3_SDIO_CTRL_CardOptionSetup 0x50
+#define ASIC3_SDIO_CTRL_ErrorStatus0 0x54
+#define ASIC3_SDIO_CTRL_ErrorStatus1 0x58
+#define ASIC3_SDIO_CTRL_DataPort 0x60
+#define ASIC3_SDIO_CTRL_TransactionCtrl 0x68
+#define ASIC3_SDIO_CTRL_CardIntCtrl 0x6C
+#define ASIC3_SDIO_CTRL_ClocknWaitCtrl 0x70
+#define ASIC3_SDIO_CTRL_HostInformation 0x74
+#define ASIC3_SDIO_CTRL_ErrorCtrl 0x78
+#define ASIC3_SDIO_CTRL_LEDCtrl 0x7C
+#define ASIC3_SDIO_CTRL_SoftwareReset 0x1C0
+
+#define ASIC3_MAP_SIZE 0x2000
+
+#endif /* __ASIC3_H__ */
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/