Re: [PATCH 0/5][RFC] Physical PCI slot objects

From: Gary Hade
Date: Wed Nov 14 2007 - 13:14:18 EST

Next message: Ravinandan Arakali (rarakali): "RE: Question about free/used memory on Linux"
Previous message: Morrison, Tom: "RE: 2.6.23.1 - sata_mv (7042) hang with large file operations"
In reply to: Alex Chiang: "Re: [PATCH 0/5][RFC] Physical PCI slot objects"
Next in thread: Alex Chiang: "Re: [PATCH 0/5][RFC] Physical PCI slot objects"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On Wed, Nov 14, 2007 at 07:42:37AM -0700, Alex Chiang wrote:
> Hi Gary,
>
> * Gary Hade <garyhade@xxxxxxxxxx>:
> >
> > I am not fundamentally opposed to this new capability but share
> > the same concerns that Greg and others have expressed. So far,
> > I have only tried the changes on one single node system (IBM
> > x3850) but the below NAK-worthy result supports the idea that
> > the changes need to be well and widely tested.
>
> Can you send me the lspci -vv and lspci -vt output from this
> machine?

Alex, I added some slot number hints to the below `lspci -vt`
output.

I am still looking at your other message and will have some
hopefully helpful comments soon. I did apply all 5 patches,
4 was a typo.

Thanks,
Gary

--
Gary Hade
System x Enablement
IBM Linux Technology Center
503-578-4503 IBM T/L: 775-4503
garyhade@xxxxxxxxxx
http://www.ibm.com/linux/ltc

Script started on Wed 14 Nov 2007 03:38:14 AM PST
0;root@elm3a9:~[root@elm3a9 ~]# lspci -vt
-+-[0000:19]---00.0-[0000:1a-1d]--+-00.0 Intel Corporation 82571EB Gigabit Ethernet Controller <- slot 6
| \-00.1 Intel Corporation 82571EB Gigabit Ethernet Controller
+-[0000:14]---00.0-[0000:15-18]-- <- slot 5
+-[0000:0f]---00.0-[0000:10-13]-- <- slot 4
+-[0000:0a]---00.0-[0000:0b-0e]----00.0-[0000:0c]----04.0 Adaptec ASC-29320ALP U320 <- slot 3
+-[0000:06]---00.0 IBM Calgary PCI-X Host Bridge <- slot 2
+-[0000:02]-+-00.0 IBM Calgary PCI-X Host Bridge <- slot 1
| \-01.0 S2io Inc. Xframe II 10Gbps Ethernet
+-[0000:01]-+-00.0 IBM Calgary PCI-X Host Bridge
| +-01.0 Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet
| +-01.1 Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet
| \-02.0 Adaptec AIC-9410W SAS (Razor ASIC non-RAID)
\-[0000:00]-+-00.0 IBM Calgary PCI-X Host Bridge
+-01.0 ATI Technologies Inc Radeon RV100 QY [Radeon 7000/VE]
+-03.0 NEC Corporation USB
+-03.1 NEC Corporation USB
+-03.2 NEC Corporation USB 2.0
+-0f.0 Broadcom CSB6 South Bridge
+-0f.1 Broadcom CSB6 RAID/IDE Controller
\-0f.3 Broadcom GCLE-2 Host Bridge
0;root@elm3a9:~[root@elm3a9 ~]# lspci -vvv
00:00.0 Host bridge: IBM Calgary PCI-X Host Bridge (rev 04)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 240
Capabilities: [60] PCI-X non-bridge device
Command: DPERE- ERO- RBC=512 OST=2
Status: Dev=00:00.0 64bit+ 133MHz+ SCD- USC- DC=bridge DMMRBC=512 DMOST=2 DMCRS=8 RSCEM- 266MHz+ 533MHz-

00:01.0 VGA compatible controller: ATI Technologies Inc Radeon RV100 QY [Radeon 7000/VE] (prog-if 00 [VGA])
Subsystem: IBM IBM eServer xSeries server mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 240 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 5
Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 1800 [size=256]
Region 2: Memory at f1c00000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at f1c20000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:03.0 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 240 (250ns min, 10500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at f1c10000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+

00:03.1 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 240 (250ns min, 10500ns max), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 20
Region 0: Memory at f1c11000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:03.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-if 20 [EHCI])
Subsystem: NEC Corporation USB 2.0
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 240 (4000ns min, 8500ns max), Cache Line Size: 128 bytes
Interrupt: pin C routed to IRQ 20
Region 0: Memory at f1c12000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0f.0 Host bridge: Broadcom CSB6 South Bridge (rev a0)
Subsystem: Broadcom Unknown device 0201
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 240

00:0f.1 IDE interface: Broadcom CSB6 RAID/IDE Controller (rev a0) (prog-if 82 [Master PriP])
Subsystem: Broadcom Unknown device 0212
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 0700 [size=16]

00:0f.3 ISA bridge: Broadcom GCLE-2 Host Bridge
Subsystem: Broadcom Unknown device 0230
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0

01:00.0 Host bridge: IBM Calgary PCI-X Host Bridge (rev 04)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 240
Capabilities: [60] PCI-X non-bridge device
Command: DPERE- ERO- RBC=512 OST=2
Status: Dev=01:00.0 64bit+ 133MHz+ SCD- USC- DC=bridge DMMRBC=512 DMOST=2 DMCRS=8 RSCEM- 266MHz+ 533MHz-

01:01.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet (rev 10)
Subsystem: IBM Unknown device 02e7
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 240 (16000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 24
Region 0: Memory at f1dc0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [40] PCI-X non-bridge device
Command: DPERE- ERO- RBC=2048 OST=1
Status: Dev=01:01.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz-
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
Address: 00000000fee00000 Data: 4056

01:01.1 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet (rev 10)
Subsystem: IBM Unknown device 02e7
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 240 (16000ns min), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 28
Region 0: Memory at f1dd0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [40] PCI-X non-bridge device
Command: DPERE- ERO- RBC=512 OST=1
Status: Dev=01:01.1 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz-
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D3 PME-Enable+ DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
Address: 00000000fee00000 Data: 4056

01:02.0 SCSI storage controller: Adaptec AIC-9410W SAS (Razor ASIC non-RAID) (rev 08)
Subsystem: IBM Unknown device 02e7
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 240 (32000ns min, 26750ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 25
Region 0: Memory at f1d80000 (64-bit, non-prefetchable) [size=256K]
Region 2: Memory at f0c00000 (64-bit, prefetchable) [size=128K]
Region 4: I/O ports at 1900 [size=256]
[virtual] Expansion ROM at f1d00000 [disabled] [size=512K]
Capabilities: [40] PCI-X non-bridge device
Command: DPERE- ERO- RBC=4096 OST=8
Status: Dev=01:02.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=4096 DMOST=8 DMCRS=128 RSCEM- 266MHz- 533MHz-
Capabilities: [58] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [e0] Message Signalled Interrupts: 64bit+ Queue=0/2 Enable-
Address: 00000000fee00000 Data: 4055

02:00.0 Host bridge: IBM Calgary PCI-X Host Bridge (rev 04)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 240
Capabilities: [60] PCI-X non-bridge device
Command: DPERE- ERO- RBC=512 OST=2
Status: Dev=02:00.0 64bit+ 133MHz+ SCD- USC- DC=bridge DMMRBC=512 DMOST=2 DMCRS=8 RSCEM- 266MHz+ 533MHz-

02:01.0 Ethernet controller: S2io Inc. Xframe II 10Gbps Ethernet (rev 02)
Subsystem: S2io Inc. Unknown device 6020
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 240 (63750ns min, 250ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f0e00000 (64-bit, prefetchable) [size=32K]
Region 2: Memory at f0d00000 (64-bit, prefetchable) [size=1M]
Region 4: Memory at f0e08000 (64-bit, prefetchable) [size=2K]
[virtual] Expansion ROM at f1e00000 [disabled] [size=1M]
Capabilities: [40] Message Signalled Interrupts: 64bit+ Queue=0/5 Enable-
Address: 00000000fee00000 Data: 4056
Capabilities: [60] PCI-X non-bridge device
Command: DPERE+ ERO+ RBC=4096 OST=8
Status: Dev=02:01.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=4096 DMOST=32 DMCRS=1024 RSCEM- 266MHz+ 533MHz-
Capabilities: [80] Vital Product Data
Capabilities: [90] MSI-X: Enable- Mask- TabSize=64
Vector table: BAR=4 offset=00000000
PBA: BAR=4 offset=00000400
Capabilities: [a0] Power Management version 3
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-

06:00.0 Host bridge: IBM Calgary PCI-X Host Bridge (rev 04)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 240
Capabilities: [60] PCI-X non-bridge device
Command: DPERE- ERO- RBC=512 OST=2
Status: Dev=06:00.0 64bit+ 133MHz+ SCD- USC- DC=bridge DMMRBC=512 DMOST=2 DMCRS=8 RSCEM- 266MHz+ 533MHz-

0a:00.0 PCI bridge: IBM CalIOC2 PCI-E Root Port (rev 01) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=0a, secondary=0b, subordinate=0e, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 512 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 256 bytes, MaxReadReq 4096 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s L1, Port 0
Link: Latency L0s <256ns, L1 <2us
Link: ASPM Disabled RCB 128 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl+ MRL+ AtnInd+ PwrInd+ HotPlug+ Surpise+
Slot: Number 3, PowerLimit 25.000000
Slot: Enabled AtnBtn- PwrFlt+ MRL+ PresDet- CmdCplt- HPIrq+
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable+ Non-Fatal+ Fatal+ PME+
Capabilities: [100] Advanced Error Reporting

0b:00.0 PCI bridge: PLX Technology, Inc. PEX 8114 PCI Express-to-PCI/PCI-X Bridge (rev bc) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Region 0: Memory at f2000000 (32-bit, non-prefetchable) [size=8K]
Bus: primary=0b, secondary=0c, subordinate=0c, sec-latency=240
I/O behind bridge: 00003000-00003fff
Memory behind bridge: f1f00000-f1ffffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Power Management version 3
Flags: PMEClk+ DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 00000000fee00000 Data: 4052
Capabilities: [58] PCI-X bridge device
Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz
Status: Dev=0b:00.0 64bit- 133MHz- SCD- USC- SCO+ SRD-
Upstream: Capacity=16 CommitmentLimit=16
Downstream: Capacity=16 CommitmentLimit=16
Capabilities: [68] Express PCI/PCI-X Bridge IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn+ AtnInd+ PwrInd+
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 256 bytes, MaxReadReq 2048 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s L1, Port 0
Link: Latency L0s <2us, L1 <32us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [100] Device Serial Number df-0e-00-00-01-00-00-00
Capabilities: [fb4] Advanced Error Reporting
Capabilities: [138] Power Budgeting
Capabilities: [148] Virtual Channel

0c:04.0 SCSI storage controller: Adaptec ASC-29320ALP U320 (rev 10)
Subsystem: Adaptec Unknown device 0045
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 240 (10000ns min, 6250ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 52
Region 0: I/O ports at 3000 [disabled] [size=256]
Region 1: Memory at f1f80000 (64-bit, non-prefetchable) [size=8K]
Region 3: I/O ports at 3100 [disabled] [size=256]
[virtual] Expansion ROM at f1f00000 [disabled] [size=512K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a0] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable-
Address: 00000000fee00000 Data: 4052
Capabilities: [94] PCI-X non-bridge device
Command: DPERE- ERO+ RBC=2048 OST=8
Status: Dev=0c:04.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=8 DMCRS=64 RSCEM- 266MHz- 533MHz-

0f:00.0 PCI bridge: IBM CalIOC2 PCI-E Root Port (rev 01) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=0f, secondary=10, subordinate=13, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 512 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 512 bytes, MaxReadReq 4096 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s L1, Port 1
Link: Latency L0s <256ns, L1 <2us
Link: ASPM Disabled RCB 128 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Slot: AtnBtn- PwrCtrl+ MRL+ AtnInd+ PwrInd+ HotPlug+ Surpise+
Slot: Number 4, PowerLimit 25.000000
Slot: Enabled AtnBtn- PwrFlt+ MRL+ PresDet- CmdCplt- HPIrq+
Slot: AttnInd Off, PwrInd Off, Power+
Root: Correctable+ Non-Fatal+ Fatal+ PME+
Capabilities: [100] Advanced Error Reporting

14:00.0 PCI bridge: IBM CalIOC2 PCI-E Root Port (rev 01) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=14, secondary=15, subordinate=18, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 512 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 512 bytes, MaxReadReq 4096 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s L1, Port 2
Link: Latency L0s <256ns, L1 <2us
Link: ASPM Disabled RCB 128 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Slot: AtnBtn- PwrCtrl+ MRL+ AtnInd+ PwrInd+ HotPlug+ Surpise+
Slot: Number 5, PowerLimit 25.000000
Slot: Enabled AtnBtn- PwrFlt+ MRL+ PresDet- CmdCplt- HPIrq+
Slot: AttnInd Off, PwrInd Off, Power+
Root: Correctable+ Non-Fatal+ Fatal+ PME+
Capabilities: [100] Advanced Error Reporting

19:00.0 PCI bridge: IBM CalIOC2 PCI-E Root Port (rev 01) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=19, secondary=1a, subordinate=1d, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 512 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s L1, Port 3
Link: Latency L0s <256ns, L1 <2us
Link: ASPM Disabled RCB 128 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Slot: AtnBtn- PwrCtrl+ MRL+ AtnInd+ PwrInd+ HotPlug+ Surpise+
Slot: Number 6, PowerLimit 25.000000
Slot: Enabled AtnBtn- PwrFlt+ MRL+ PresDet- CmdCplt- HPIrq+
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable+ Non-Fatal+ Fatal+ PME+
Capabilities: [100] Advanced Error Reporting

1a:00.0 Ethernet controller: Intel Corporation 82571EB Gigabit Ethernet Controller (rev 06)
Subsystem: Intel Corporation PRO/1000 PT Dual Port Server Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 55
Region 0: Memory at f2100000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at f2120000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 1a00 [size=32]
[virtual] Expansion ROM at f2140000 [disabled] [size=128K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 00000000fee00000 Data: 407b
Capabilities: [e0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <64us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 0
Link: Latency L0s <4us, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Device Serial Number ce-c4-0b-ff-ff-17-15-00

1a:00.1 Ethernet controller: Intel Corporation 82571EB Gigabit Ethernet Controller (rev 06)
Subsystem: Intel Corporation PRO/1000 PT Dual Port Server Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 59
Region 0: Memory at f2160000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at f2180000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 1a20 [size=32]
[virtual] Expansion ROM at f21a0000 [disabled] [size=128K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 00000000fee00000 Data: 4083
Capabilities: [e0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <64us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 0
Link: Latency L0s <4us, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Device Serial Number ce-c4-0b-ff-ff-17-15-00

0;root@elm3a9:~[root@elm3a9 ~]# exit
exit

Script done on Wed 14 Nov 2007 03:38:23 AM PST
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Next message: Ravinandan Arakali (rarakali): "RE: Question about free/used memory on Linux"
Previous message: Morrison, Tom: "RE: 2.6.23.1 - sata_mv (7042) hang with large file operations"
In reply to: Alex Chiang: "Re: [PATCH 0/5][RFC] Physical PCI slot objects"
Next in thread: Alex Chiang: "Re: [PATCH 0/5][RFC] Physical PCI slot objects"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]