Re: Iomega ZIP-100 drive unsupported with jmicron JMB361 chip?

[Bill Davidsen]

trash can wrote:
> -----BEGIN PGP SIGNED MESSAGE-----
> Hash: SHA1
>
> Success!
> I downloaded kernel-2.6.24-0.81.rc4.git7.fc9.src.rpm from the Fedora
> development tree. Went through "rpm dependecy hell" and solved all
> dependencies by installing other fc9 rpms. I used
> config-2.6.23.1-42.fc8 as my starting point. My
> config-2.6.24-0.81.rc4.git7.local.fc8 is attached.
>
> After compilation and installation of the kernel rpm, upon boot I could
> see a device sdc4 being created, but boot failed with
> "mount: missing mount point", some errors in mounting from setuproot and
> switchroot.
>
> I believe the problem was with the Red Hat/Fedora anaconda installer
> and/or grub, and my multiboot machine setup. I had not been able to boot
> updated fc8 kernel packages, only the originally installed kernel.
> Note that my Fedora 7 and Fedora 8 distributions share no directories
> (one exception) and all this work is taking place in the Fedora 8
> distribution. The /boot partition IS shared among my distributions.
> I found my /etc/fstab file had two "/" mount point entries. The last line
> contained LABEL=/ and is a reference to my Fedora 7 root partition.
> I deleted this line from fstab as I did not want to change the mount
> point for this line to mount my Fedora 7 distribution on Fedora 8.
> This kernel installation process was appending LABEL=/ to my kernel
> line in grub.conf:
> kernel /vmlinuz-2.6.24-0.81.rc4.git7.local.fc8 ro root=/dev/VGf800/LogVol00 rhgb quiet LABEL=/
>
> LABEL=/ was removed from the line.
>
> I then needed to recreate my initrd image:
> mkinitrd /boot/initrd-2.6.24-0.81.rc4.git7.local.fc8.img \
>   2.6.24-0.81.rc4.git7.local.fc8
>
> Finally I was able to boot (Zip disk inserted) to the local kernel and the
> Zip drive works as expected.
>
> # blkid
> /dev/sdc4: SEC_TYPE="msdos" LABEL="ZIP-100" UUID="4910-1305" TYPE="vfat"
>
> dmesg:
> ata9.00: ATAPI: LITE-ON DVDRW SOHW-1693S, KS0B, max UDMA/66
> ata9.01: ATAPI: IOMEGA  ZIP 100       ATAPI, 05.H, max MWDMA1, CDB intr
> ata9.00: limited to UDMA/33 due to 40-wire cable
> ata9.00: configured for UDMA/33
> ata9.01: configured for MWDMA1
> scsi 8:0:0:0: CD-ROM            LITE-ON  DVDRW SOHW-1693S KS0B PQ: 0 ANSI: 5
> scsi 8:0:1:0: Direct-Access     IOMEGA   ZIP 100          05.H PQ: 0 ANSI: 5
> sd 8:0:1:0: [sdc] 196608 512-byte hardware sectors (101 MB)
> sd 8:0:1:0: [sdc] Write Protect is off
> sd 8:0:1:0: [sdc] Mode Sense: 00 40 00 00
> sd 8:0:1:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> sd 8:0:1:0: [sdc] 196608 512-byte hardware sectors (101 MB)
> sd 8:0:1:0: [sdc] Write Protect is off
> sd 8:0:1:0: [sdc] Mode Sense: 00 40 00 00
> sd 8:0:1:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
>  sdc: sdc4
>
> My thanks to all the great people who solved this problem and those who patiently
> responded to my queries.
>
> - -RoyBoy626
I've been behing reading this list, I was going to say that I have 
always had best luck with those drives using the old idescsi driver, 
although I haven't used a kernel newer than... 2.6.18 or so on the old 
machines. Since you have a solution I won't suggest you try that with an 
old kernel ;-)

--
Bill Davidsen <davidsen@xxxxxxx>
  "We have more to fear from the bungling of the incompetent than from
the machinations of the wicked."  - from Slashdot
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/