Re: 2.6.25-rc5-mm1

[Torsten Kaiser]

On Wed, Mar 12, 2008 at 9:01 PM, Torsten Kaiser
<just.for.lkml@xxxxxxxxxxxxxx> wrote:
> On Wed, Mar 12, 2008 at 8:44 PM, Andrew Morton
> <akpm@xxxxxxxxxxxxxxxxxxxx> wrote:
> >  OK, so it looks like it died during networking initialisation.
>  >
>  >  Could you please add initcall_debug to the boot command line so we can see
>  >  which function it is getting stuck in?
>
>  Yes, here is the result:
>  [    2.573979] PCI-DMA: Disabling AGP.
>  [    2.577639] PCI-DMA: aperture base @ 8000000 size 65536 KB
>  [    2.589504] PCI-DMA: using GART IOMMU.
>  [    2.593258] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
>  [    2.600132] initcall pci_iommu_init+0x0/0x20() returned 0 after 19 msecs
>  [    2.622146] calling  hpet_late_init+0x0/0x140()
>  [    2.626689] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
>  [    2.633022] hpet0: 3 32-bit timers, 25000000 Hz
>  [    2.638562] initcall hpet_late_init+0x0/0x140() returned 0 after 9 msecs
>  [    2.654545] calling  clocksource_done_booting+0x0/0x20()
>  [    2.659855] initcall clocksource_done_booting+0x0/0x20()<6>Time:
>
> hpet clocksource has been installed.
>  [    2.662185]  returned 0 after 0 msecs
>  [    2.688448] calling  init_pipe_fs+0x0/0x60()
>  [    2.695423] initcall init_pipe_fs+0x0/0x60() returned 0 after 0 msecs
>  [    2.705784] calling  init_mnt_writers+0x0/0x70()
>  [    2.711681] initcall init_mnt_writers+0x0/0x70() returned 0 after 0 msecs
>  [    2.721678] calling  eventpoll_init+0x0/0x90()
>  [    2.731644] initcall eventpoll_init+0x0/0x90() returned 0 after 0 msecs
>  [    2.738295] calling  anon_inode_init+0x0/0x130()
>  [    2.751614] initcall anon_inode_init+0x0/0x130() returned 0 after 0 msecs
>  [    2.771585] calling  pcie_aspm_init+0x0/0x30()
>  [    2.779297] initcall pcie_aspm_init+0x0/0x30() returned 0 after 2 msecs
>  [    2.793911] calling  acpi_event_init+0x0/0x52()
>
>  -> it looked like the system this time already hung here. But just
>  pressing the 'Alt' key let the system continue until the network hang.
>  (I tried this a second time, again it paused here until I pressed a key)
>
>  [   94.857929] initcall acpi_event_init+0x0/0x52() returned 0 after 29276 msecs
>  [   94.865002] calling  pnp_system_init+0x0/0x20()
>  [   94.877935] system 00:06: ioport range 0x4d0-0x4d1 has been reserved
>  [   94.884286] system 00:06: ioport range 0x7b0-0x7df has been reserved
>  [   94.897886] system 00:06: ioport range 0x800-0x80f has been reserved
>  [   94.907886] system 00:06: ioport range 0xbb0-0xbdf has been reserved
>  [   94.917855] system 00:06: ioport range 0x2000-0x207f has been reserved
>  [   94.937827] system 00:06: ioport range 0x2080-0x20ff has been reserved
>  [   94.947827] system 00:06: ioport range 0x2400-0x247f has been reserved
>  [   94.957793] system 00:06: ioport range 0x2480-0x24ff has been reserved
>  [   94.977766] system 00:06: ioport range 0x2800-0x287f has been reserved
>  [   94.987766] system 00:06: ioport range 0x2880-0x28ff has been reserved
>  [   94.997734] system 00:06: ioport range 0x2c00-0x2c7f has been reserved
>  [   95.017708] system 00:06: ioport range 0x2c80-0x2cff has been reserved
>  [   95.024234] system 00:06: iomem range 0x0-0x0 could not be reserved
>  [   95.037678] system 00:06: iomem range 0xfee01000-0xfeefffff could
>  not be reserved
>  [   95.060158] system 00:06: iomem range 0xefa80000-0xefabffff has been reserved
>  [   95.070158] system 00:06: iomem range 0xffb00000-0xffbfffff could
>  not be reserved
>  [   95.077633] system 00:06: iomem range 0xfff00000-0xffffffff could
>  not be reserved
>  [   95.097590] system 00:08: iomem range 0xfec00000-0xfec00fff could
>  not be reserved
>  [   95.120064] system 00:08: iomem range 0xfee00000-0xfee00fff could
>  not be reserved
>  [   95.130070] system 00:0c: ioport range 0x290-0x297 has been reserved
>  [   95.137523] system 00:0d: iomem range 0x0-0x9ffff could not be reserved
>  [   95.157495] system 00:0d: iomem range 0xc0000-0xcffff has been reserved
>  [   95.167495] system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
>  [   95.177463] system 00:0d: iomem range 0x100000-0xdfffffff could not
>  be reserved
>  [   95.197437] system 00:0d: iomem range 0xfec00000-0xffffffff could
>  not be reserved
>  [   95.219983] initcall pnp_system_init+0x0/0x20() returned 0 after 162 msecs
>  [   95.226887] calling  chr_dev_init+0x0/0xd0()
>  [   95.237813] initcall chr_dev_init+0x0/0xd0() returned 0 after 0 msecs
>  [   95.247378] calling  firmware_class_init+0x0/0x90()
>  [   95.257320] initcall firmware_class_init+0x0/0x90() returned 0 after 0 msecs
>  [   95.276031] calling  loopback_init+0x0/0x20()
>  [   95.288590] initcall loopback_init+0x0/0x20() returned 0 after 0 msecs
>  [   95.296837] calling  cpufreq_gov_performance_init+0x0/0x20()
>  [   95.309084] initcall cpufreq_gov_performance_init+0x0/0x20()
>  returned 0 after 0 msecs
>  [   95.317734] calling  cpufreq_gov_dbs_init+0x0/0x50()
>  [   95.338090] initcall cpufreq_gov_dbs_init+0x0/0x50() returned 0 after 0 msecs
>  [   95.345254] calling  init_acpi_pm_clocksource+0x0/0xc0()
>  [   95.355293] initcall init_acpi_pm_clocksource+0x0/0xc0() returned 0
>  after 0 msecs
>  [   95.374115] calling  pcibios_assign_resources+0x0/0x90()
>  [   95.379618] PCI: Bridge: 0000:00:06.0
>  [   95.394087]   IO window: disabled.
>  [   95.397502]   MEM window: 0xeff00000-0xefffffff
>  [   95.402032]   PREFETCH window: 0x00000000eef00000-0x00000000eeffffff
>  [   95.415189] PCI: Bridge: 0000:00:0b.0
>  [   95.418860]   IO window: e000-efff
>  [   95.438075]   MEM window: 0xefe00000-0xefefffff
>  [   95.442610]   PREFETCH window: disabled.
>  [   95.455526] PCI: Bridge: 0000:00:0c.0
>  [   95.459197]   IO window: disabled.
>  [   95.462604]   MEM window: 0xefd00000-0xefdfffff
>  [   95.475513]   PREFETCH window: disabled.
>  [   95.479443] PCI: Bridge: 0000:00:0d.0
>  [   95.485512]   IO window: disabled.
>  [   95.495480]   MEM window: 0xefc00000-0xefcfffff
>  [   95.500010]   PREFETCH window: disabled.
>  [   95.515455] PCI: Bridge: 0000:00:0f.0
>  [   95.519124]   IO window: d000-dfff
>  [   95.522533]   MEM window: 0xefb00000-0xefbfffff
>  [   95.535423]   PREFETCH window: 0x00000000e0000000-0x00000000e7ffffff
>  [   95.545456] initcall pcibios_assign_resources+0x0/0x90() returned 0
>  after 79 msecs
>  [   95.557830] calling  fill_mp_bus_to_cpumask+0x0/0x100()
>  [   95.575408] initcall fill_mp_bus_to_cpumask+0x0/0x100() returned 0
>  after 0 msecs
>  [   95.593777] calling  inet_init+0x0/0x380()
>  [   95.597890] NET: Registered protocol family 2
>
>  -> same hang, no reaction to SysRq.
>
>  What looks suspicious: The call to pcie_aspm_init is just before the
>  temporary hang. When I used make oldconfig to upgrade the .config from
>  2.6.25-rc3-mm1 to -rc5-mm1 I activated the new option CONFIG_PCIEASPM.
>
>  I will try with CONFIG_PCIEASPM_DEBUG added and completely without this option.

CONFIG_PCIEASPM does not change anything.
Also testing the range of ipc patches you suggested to Badari did not fix it.

I did a bisect, these patches are currently remaining, but I dod not
have the time for more bisect steps until tomorrow:

git-scsi-misc
git-sh
execute-tasklets-in-the-same-order-they-were-queued
git-sched
sched: work around hrtick related lockup
sched: make sure jiffies is up to date before calling __update_rq_clock()
sched: fix rq->clock overflows detection with CONFIG_NO_HZ
sched: make cpu_clock() globally synchronous
sched: remove isolcpus
ftrace: make the task state char-string visible to all
sched: add latency tracer callbacks to the scheduler
latencytop: optimize LT_BACKTRACEDEPTH loops a bit
sched: cleanup old and rarely used 'debug' features.
[SCSI] zfcp: convert zfcp to use target reset and device reset handler
[SCSI] qla4xxx: Add target reset functionality
[SCSI] scsi_error: add target reset handler
[SCSI] ps3rom: Simplify fill_from_dev_buffer()
[SCSI] scsi_debug: use shost_priv macro
[SCSI] scsi_debug: remove unnecessary checking
[SCSI] scsi_debug: remove scsi_debug.h
[SCSI] scsi_debug: stop including drivers/scsi/scsi.h
[SCSI] Remove random noop unchecked_isa_dma users
[SCSI] aacraid: READ_CAPACITY_16 shouldn't trust allocation length in cdb
[SCSI] st: show options currently set in sysfs
[SCSI] st: add option to use SILI in variable block reads
[SCSI] gdth: remove command accessors
[SCSI] aic94xx: Use sas_request_addr() to provide SAS WWN if the
adapter lacks one
[SCSI] libsas: Provide a transport-level facility to request SAS addrs
[SCSI] ips: sg chaining support to the path to non I/O commands
[SCSI] gdth: convert to PCI hotplug API
[SCSI] gdth: PCI probe cleanups, prep for PCI hotplug API conversion
rtc: rtc-sh: Add support for periodic IRQs.
sh: SuperH KEYSC keypad data for Solution Engine 7722
sh: SuperH KEYSC keypad data for MigoR
sh: SuperH KEYSC platform driver

Torsten
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/