Re: nobody cared about IRQ 19 (firewire, on a HP 2510p notebook)
From: Martin Michlmayr
Date: Sun Mar 30 2008 - 12:13:21 EST
* Stefan Richter <stefanr@xxxxxxxxxxxxxxxxx> [2008-03-30 13:11]:
> Martin, please check whether the same happens if you disable firewire-ohci
> in the kernel config (or blacklist it in the modprobe config) and use the
> ohci1394 driver instead.
Yes, I get essentially the same message with the ohci1394 driver:
[ 895.455783] irq 19: nobody cared (try booting with the "irqpoll" option)
[ 895.455783] Pid: 0, comm: swapper Not tainted 2.6.25-rc7-amd64 #1
[ 895.455783]
[ 895.455783] Call Trace:
[ 895.455783] <IRQ> [<ffffffff88078155>] :ohci1394:ohci_irq_handler+0x4b/0x76e
[ 895.455783] [<ffffffff8026c883>] __report_bad_irq+0x30/0x72
[ 895.455783] [<ffffffff8026cac2>] note_interrupt+0x1fd/0x23f
[ 895.455783] [<ffffffff8026d34f>] handle_fasteoi_irq+0xa5/0xc8
[ 895.455783] [<ffffffff8020f53c>] do_IRQ+0x6d/0xd9
[ 895.455783] [<ffffffff8020c46d>] ret_from_intr+0x0/0x19
[ 895.455783] <EOI> [<ffffffff803a25a4>] menu_reflect+0x0/0x75
[ 895.455783] [<ffffffff8800642b>] :processor:acpi_idle_enter_simple+0x18d/0x1fe
[ 895.455783] [<ffffffff803a1b2b>] cpuidle_idle_call+0x7a/0xb3
[ 895.455783] [<ffffffff803a1ab1>] cpuidle_idle_call+0x0/0xb3
[ 895.455783] [<ffffffff8020b06c>] cpu_idle+0xa9/0xd3
[ 895.455783]
[ 895.455783] handlers:
[ 895.455783] [<ffffffff8807810a>] (ohci_irq_handler+0x0/0x76e [ohci1394])
[ 895.455783] Disabling IRQ #19
dmesg is attached.
--
Martin Michlmayr
http://www.cyrius.com/
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Linux version 2.6.25-rc7-amd64 (Debian 2.6.25~rc7-1~experimental.1~snapshot.11011) (waldi@xxxxxxxxxx) (gcc version 4.1.3 20080114 (prerelease) (Debian 4.1.2-19)) #1 SMP Sun Mar 30 17:36:02 CEST 2008
[ 0.000000] Command line: root=/dev/mapper/lucky-root ro vga=791
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007f7b0000 (usable)
[ 0.000000] BIOS-e820: 000000007f7b0000 - 000000007f7c5400 (reserved)
[ 0.000000] BIOS-e820: 000000007f7c5400 - 000000007f7e7fb8 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007f7e7fb8 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed20000 - 00000000fed9a000 (reserved)
[ 0.000000] BIOS-e820: 00000000feda0000 - 00000000fedc0000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffb00000 - 00000000ffc00000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 256, 522160) 1 entries of 3200 used
[ 0.000000] end_pfn_map = 1048576
[ 0.000000] DMI 2.4 present.
[ 0.000000] ACPI: RSDP 000F77A0, 0024 (r2 HP )
[ 0.000000] ACPI: XSDT 7F7C81C4, 0074 (r1 HPQOEM SLIC-MPC 1 HP 1)
[ 0.000000] ACPI: FACP 7F7C8084, 00F4 (r4 HP 30C9 3 HP 1)
[ 0.000000] ACPI: DSDT 7F7C84C0, 13484 (r1 HP nc2500 10000 MSFT 3000001)
[ 0.000000] ACPI: FACS 7F7E7D80, 0040
[ 0.000000] ACPI: SLIC 7F7C8238, 0176 (r1 HPQOEM SLIC-MPC 1 HP 1)
[ 0.000000] ACPI: HPET 7F7C83B0, 0038 (r1 HP 30C9 1 HP 1)
[ 0.000000] ACPI: APIC 7F7C83E8, 0068 (r1 HP 30C9 1 HP 1)
[ 0.000000] ACPI: MCFG 7F7C8450, 003C (r1 HP 30C9 1 HP 1)
[ 0.000000] ACPI: TCPA 7F7C848C, 0032 (r2 HP 30C9 1 HP 1)
[ 0.000000] ACPI: SSDT 7F7DB944, 02BE (r1 HP HPQPAT 1 MSFT 3000001)
[ 0.000000] ACPI: SSDT 7F7DC586, 025F (r1 HP Cpu0Tst 3000 INTL 20060317)
[ 0.000000] ACPI: SSDT 7F7DC7E5, 00A6 (r1 HP Cpu1Tst 3000 INTL 20060317)
[ 0.000000] ACPI: SSDT 7F7DC88B, 04D7 (r1 HP CpuPm 3000 INTL 20060317)
[ 0.000000] ACPI: DMI detected: Hewlett-Packard
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-000000007f7b0000
[ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 256, 522160) 1 entries of 3200 used
[ 0.000000] Bootmem setup node 0 0000000000000000-000000007f7b0000
[ 0.000000] NODE_DATA [000000000000c000 - 0000000000012fff]
[ 0.000000] bootmap [0000000000013000 - 0000000000022ef7] pages 10
[ 0.000000] early res: 0 [0-fff] BIOS data page
[ 0.000000] early res: 1 [6000-7fff] SMP_TRAMPOLINE
[ 0.000000] early res: 2 [200000-6464a7] TEXT DATA BSS
[ 0.000000] early res: 3 [37909000-37fef295] RAMDISK
[ 0.000000] early res: 4 [9fc00-a0bff] EBDA
[ 0.000000] early res: 5 [8000-bfff] PGTABLE
[ 0.000000] No mptable found.
[ 0.000000] [ffffe20000000000-ffffe200001fffff] PMD ->ffff810001200000 on node 0
[ 0.000000] [ffffe20000200000-ffffe200003fffff] PMD ->ffff810001600000 on node 0
[ 0.000000] [ffffe20000400000-ffffe200005fffff] PMD ->ffff810001a00000 on node 0
[ 0.000000] [ffffe20000600000-ffffe200007fffff] PMD ->ffff810001e00000 on node 0
[ 0.000000] [ffffe20000800000-ffffe200009fffff] PMD ->ffff810002200000 on node 0
[ 0.000000] [ffffe20000a00000-ffffe20000bfffff] PMD ->ffff810002600000 on node 0
[ 0.000000] [ffffe20000c00000-ffffe20000dfffff] PMD ->ffff810002a00000 on node 0
[ 0.000000] [ffffe20000e00000-ffffe20000ffffff] PMD ->ffff810002e00000 on node 0
[ 0.000000] [ffffe20001000000-ffffe200011fffff] PMD ->ffff810003200000 on node 0
[ 0.000000] [ffffe20001200000-ffffe200013fffff] PMD ->ffff810003600000 on node 0
[ 0.000000] [ffffe20001400000-ffffe200015fffff] PMD ->ffff810003a00000 on node 0
[ 0.000000] [ffffe20001600000-ffffe200017fffff] PMD ->ffff810003e00000 on node 0
[ 0.000000] [ffffe20001800000-ffffe200019fffff] PMD ->ffff810004200000 on node 0
[ 0.000000] [ffffe20001a00000-ffffe20001bfffff] PMD ->ffff810004600000 on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] DMA32 4096 -> 1048576
[ 0.000000] Normal 1048576 -> 1048576
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0 -> 159
[ 0.000000] 0: 256 -> 522160
[ 0.000000] On node 0 totalpages: 522063
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 1102 pages reserved
[ 0.000000] DMA zone: 2841 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 7082 pages used for memmap
[ 0.000000] DMA32 zone: 510982 pages, LIFO batch:31
[ 0.000000] Normal zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 (Bootup-CPU)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] Processor #1
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Setting APIC routing to flat
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:7ec00000)
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] PERCPU: Allocating 35224 bytes of per cpu data
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 513823
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: root=/dev/mapper/lucky-root ro vga=791
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] TSC calibrated against PM_TIMER
[ 0.000002] time.c: Detected 1196.997 MHz processor.
[ 0.000032] Console: colour dummy device 80x25
[ 0.000037] console [tty0] enabled
[ 0.000312] Checking aperture...
[ 0.000331] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000334] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.004000] Memory: 2047828k/2088640k available (2205k kernel code, 40424k reserved, 1027k data, 372k init)
[ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.004000] hpet clockevent registered
[ 0.080009] Calibrating delay using timer specific routine.. 2397.31 BogoMIPS (lpj=4794630)
[ 0.080086] Security Framework initialized
[ 0.080096] SELinux: Disabled at boot.
[ 0.080103] Capability LSM initialized
[ 0.080473] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.082280] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.083202] Mount-cache hash table entries: 256
[ 0.083437] Initializing cgroup subsys ns
[ 0.083446] Initializing cgroup subsys cpuacct
[ 0.083480] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.083486] CPU: L2 cache: 2048K
[ 0.083493] CPU 0/0 -> Node 0
[ 0.083497] CPU: Physical Processor ID: 0
[ 0.083502] CPU: Processor Core ID: 0
[ 0.083515] CPU0: Thermal monitoring handled by SMI
[ 0.083518] using mwait in idle threads.
[ 0.084015] ACPI: Core revision 20070126
[ 0.159876] Using local APIC timer interrupts.
[ 0.160012] APIC timer calibration result 8312479
[ 0.160015] Detected 8.312 MHz APIC timer.
[ 0.160258] Booting processor 1/2 APIC 0x1
[ 0.004000] Initializing CPU#1
[ 0.004000] Calibrating delay using timer specific routine.. 2394.00 BogoMIPS (lpj=4788003)
[ 0.004000] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.004000] CPU: L2 cache: 2048K
[ 0.004000] CPU 1/1 -> Node 0
[ 0.004000] CPU: Physical Processor ID: 0
[ 0.004000] CPU: Processor Core ID: 1
[ 0.004000] CPU1: Thermal monitoring enabled (TM2)
[ 0.004000] Intel(R) Core(TM)2 Duo CPU U7600 @ 1.20GHz stepping 0d
[ 0.248606] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.252052] Brought up 2 CPUs
[ 0.252178] CPU0 attaching sched-domain:
[ 0.252182] domain 0: span 00000003
[ 0.252185] groups: 00000001 00000002
[ 0.252190] domain 1: span 00000003
[ 0.252192] groups: 00000003
[ 0.252197] CPU1 attaching sched-domain:
[ 0.252199] domain 0: span 00000003
[ 0.252202] groups: 00000002 00000001
[ 0.252206] domain 1: span 00000003
[ 0.252209] groups: 00000003
[ 0.252620] net_namespace: 1016 bytes
[ 0.252631] Booting paravirtualized kernel on bare hardware
[ 0.252956] NET: Registered protocol family 16
[ 0.253264] ACPI: bus type pci registered
[ 0.253399] PCI: BIOS Bug: MCFG area at f8000000 is not E820-reserved
[ 0.253406] PCI: Not using MMCONFIG.
[ 0.253411] PCI: Using configuration type 1
[ 0.256974] ACPI: EC: Look up EC in DSDT
[ 0.007168] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 0.353529] ACPI: Interpreter enabled
[ 0.353537] ACPI: (supports S0 S3 S4 S5)
[ 0.353563] ACPI: Using IOAPIC for interrupt routing
[ 0.373665] ACPI: EC: GPE = 0x16, I/O: command/status = 0x66, data = 0x62
[ 0.373674] ACPI: EC: driver started in interrupt mode
[ 0.373769] ACPI: PCI Root Bridge [C003] (0000:00)
[ 0.375074] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[ 0.375086] pci 0000:00:1f.0: quirk: region 1100-113f claimed by ICH6 GPIO
[ 0.375967] PCI: Transparent bridge - 0000:00:1e.0
[ 0.376052] ACPI: PCI Interrupt Routing Table [\_SB_.C003._PRT]
[ 0.377033] ACPI: PCI Interrupt Routing Table [\_SB_.C003.C0B2._PRT]
[ 0.377371] ACPI: PCI Interrupt Routing Table [\_SB_.C003.C11F._PRT]
[ 0.377671] ACPI: PCI Interrupt Routing Table [\_SB_.C003.C133._PRT]
[ 0.458107] ACPI: PCI Interrupt Link [C12F] (IRQs *10 11)
[ 0.458548] ACPI: PCI Interrupt Link [C130] (IRQs *10 11)
[ 0.458983] ACPI: PCI Interrupt Link [C131] (IRQs 10 *11)
[ 0.459419] ACPI: PCI Interrupt Link [C132] (IRQs 10 11) *5
[ 0.459858] ACPI: PCI Interrupt Link [C142] (IRQs *10 11)
[ 0.460285] ACPI: PCI Interrupt Link [C143] (IRQs 10 11) *0, disabled.
[ 0.460721] ACPI: PCI Interrupt Link [C144] (IRQs 10 *11)
[ 0.460927] ACPI Exception (pci_link-0184): AE_NOT_FOUND, Evaluating _PRS [20070126]
[ 0.461281] ACPI: Power Resource [C29F] (on)
[ 0.461390] ACPI: Power Resource [C1C7] (off)
[ 0.461605] ACPI: Power Resource [C3AD] (off)
[ 0.461811] ACPI: Power Resource [C3B0] (off)
[ 0.462016] ACPI: Power Resource [C3C3] (off)
[ 0.462226] ACPI: Power Resource [C3C4] (off)
[ 0.462431] ACPI: Power Resource [C3C5] (off)
[ 0.462634] ACPI: Power Resource [C3C6] (off)
[ 0.462837] ACPI: Power Resource [C3C7] (off)
[ 0.463101] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.463152] pnp: PnP ACPI init
[ 0.463166] ACPI: bus type pnp registered
[ 0.463473] 00:00: calling quirk 0xffffffff8035b6ca: quirk_system_pci_resources+0x0/0x173()
[ 0.463550] pnp 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.470899] pnp 00:01: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 0.472215] pnp 00:02: Plug and Play ACPI device, IDs IFX0102 PNP0c31 (active)
[ 0.472303] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.472387] pnp 00:04: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.472463] pnp 00:05: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.472545] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.472933] pnp 00:07: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.473020] pnp 00:08: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.473111] pnp 00:09: Plug and Play ACPI device, IDs SYN0130 SYN0100 SYN0002 PNP0f13 (active)
[ 0.474032] 00:0a: calling quirk 0xffffffff8035b6ca: quirk_system_pci_resources+0x0/0x173()
[ 0.474113] pnp 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.478436] pnp 00:0b: Plug and Play ACPI device, IDs HPQ0004 (active)
[ 0.478561] 00:0c: calling quirk 0xffffffff8035b6ca: quirk_system_pci_resources+0x0/0x173()
[ 0.478656] pnp 00:0c: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.481318] 00:0d: calling quirk 0xffffffff8035b6ca: quirk_system_pci_resources+0x0/0x173()
[ 0.481428] pnp 00:0d: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.481457] pnp: PnP ACPI: found 14 devices
[ 0.481463] ACPI: ACPI bus type pnp unregistered
[ 0.481751] usbcore: registered new interface driver usbfs
[ 0.481841] usbcore: registered new interface driver hub
[ 0.481910] usbcore: registered new device driver usb
[ 0.482120] PCI: Using ACPI for IRQ routing
[ 0.482126] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 0.500051] NET: Registered protocol family 8
[ 0.500057] NET: Registered protocol family 20
[ 0.500124] PCI-GART: No AMD northbridge found.
[ 0.500138] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 11
[ 0.500148] hpet0: 3 64-bit timers, 14318180 Hz
[ 0.501210] ACPI: RTC can wake from S4
[ 0.504044] Switched to high resolution mode on CPU 0
[ 0.252027] Switched to high resolution mode on CPU 1
[ 0.516050] pnp: the driver 'system' has been registered
[ 0.516066] system 00:00: iomem range 0x0-0x9ffff could not be reserved
[ 0.516074] system 00:00: iomem range 0xe0000-0xfffff could not be reserved
[ 0.516082] system 00:00: iomem range 0x100000-0x7f7fffff could not be reserved
[ 0.516090] system 00:00: driver attached
[ 0.516104] system 00:0a: ioport range 0x500-0x55f has been reserved
[ 0.516112] system 00:0a: ioport range 0x800-0x80f has been reserved
[ 0.516121] system 00:0a: iomem range 0xffb00000-0xffbfffff could not be reserved
[ 0.516130] system 00:0a: iomem range 0xfff00000-0xffffffff could not be reserved
[ 0.516137] system 00:0a: driver attached
[ 0.516146] system 00:0c: ioport range 0x4d0-0x4d1 has been reserved
[ 0.516153] system 00:0c: ioport range 0x2f8-0x2ff has been reserved
[ 0.516161] system 00:0c: ioport range 0x3f8-0x3ff has been reserved
[ 0.516168] system 00:0c: ioport range 0x1000-0x107f has been reserved
[ 0.516177] system 00:0c: ioport range 0x1100-0x113f has been reserved
[ 0.516185] system 00:0c: ioport range 0x1200-0x121f has been reserved
[ 0.516193] system 00:0c: iomem range 0xf8000000-0xfbffffff has been reserved
[ 0.516201] system 00:0c: iomem range 0xfec00000-0xfec000ff could not be reserved
[ 0.516210] system 00:0c: iomem range 0xfed20000-0xfed3ffff could not be reserved
[ 0.516219] system 00:0c: iomem range 0xfed45000-0xfed8ffff could not be reserved
[ 0.516228] system 00:0c: iomem range 0xfed90000-0xfed99fff could not be reserved
[ 0.516235] system 00:0c: driver attached
[ 0.516244] system 00:0d: iomem range 0xcee00-0xcffff has been reserved
[ 0.516252] system 00:0d: iomem range 0xd2000-0xd3fff has been reserved
[ 0.516260] system 00:0d: iomem range 0xfeda0000-0xfedbffff could not be reserved
[ 0.516269] system 00:0d: iomem range 0xfee00000-0xfee00fff could not be reserved
[ 0.516277] system 00:0d: driver attached
[ 0.516934] PCI: Bridge: 0000:00:1c.0
[ 0.516940] IO window: disabled.
[ 0.516949] MEM window: disabled.
[ 0.516957] PREFETCH window: disabled.
[ 0.516969] PCI: Bridge: 0000:00:1c.1
[ 0.516973] IO window: disabled.
[ 0.516983] MEM window: 0xe0000000-0xe00fffff
[ 0.516992] PREFETCH window: disabled.
[ 0.517007] PCI: Bus 3, cardbus bridge: 0000:02:06.0
[ 0.517013] IO window: 0x00003000-0x000030ff
[ 0.517022] IO window: 0x00003400-0x000034ff
[ 0.517032] PREFETCH window: 0x88000000-0x8bffffff
[ 0.517042] MEM window: 0x8c000000-0x8fffffff
[ 0.517051] PCI: Bridge: 0000:00:1e.0
[ 0.517058] IO window: 3000-3fff
[ 0.517068] MEM window: 0xe0100000-0xe03fffff
[ 0.517077] PREFETCH window: 0x0000000088000000-0x000000008bffffff
[ 0.517121] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 0.517135] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.517166] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 17
[ 0.517179] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 0.517197] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 0.517221] ACPI: PCI Interrupt 0000:02:06.0[A] -> GSI 18 (level, low) -> IRQ 18
[ 0.517287] NET: Registered protocol family 2
[ 0.552216] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.553439] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.556763] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.557659] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.557667] TCP reno registered
[ 0.568332] checking if image is initramfs... it is
[ 1.536099] Freeing initrd memory: 7064k freed
[ 1.294389] audit: initializing netlink socket (disabled)
[ 1.294425] type=2000 audit(1206892467.541:1): initialized
[ 1.294734] Total HugeTLB memory allocated, 0
[ 1.294889] VFS: Disk quotas dquot_6.5.1
[ 1.294935] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.295081] io scheduler noop registered
[ 1.295087] io scheduler anticipatory registered
[ 1.295092] io scheduler deadline registered
[ 1.295115] io scheduler cfq registered (default)
[ 1.295132] pci 0000:00:02.0: Boot video device
[ 1.295432] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 1.295487] assign_interrupt_mode Found MSI capability
[ 1.295553] Allocate Port Service[0000:00:1c.0:pcie00]
[ 1.295699] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 1.295753] assign_interrupt_mode Found MSI capability
[ 1.295814] Allocate Port Service[0000:00:1c.1:pcie00]
[ 1.296510] vesafb: framebuffer at 0xd0000000, mapped to 0xffffc20000900000, using 3072k, total 7616k
[ 1.296521] vesafb: mode is 1024x768x16, linelength=2048, pages=3
[ 1.296527] vesafb: scrolling: redraw
[ 1.296533] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[ 1.316629] Console: switching to colour frame buffer device 128x48
[ 1.336816] fb0: VESA VGA frame buffer device
[ 1.340506] Real Time Clock Driver v1.12ac
[ 1.341047] hpet_resources: 0xfed00000 is busy
[ 1.341164] Linux agpgart interface v0.103
[ 1.341325] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 1.342027] pnp: the driver 'serial' has been registered
[ 1.342372] isa bounce pool size: 16 pages
[ 1.343772] brd: module loaded
[ 1.343989] input: Macintosh mouse button emulation as /class/input/input0
[ 1.344232] pnp: the driver 'i8042 kbd' has been registered
[ 1.344250] i8042 kbd 00:08: driver attached
[ 1.344298] pnp: the driver 'i8042 aux' has been registered
[ 1.344325] i8042 aux 00:09: driver attached
[ 1.344375] PNP: PS/2 Controller [PNP0303:C29C,PNP0f13:C29D] at 0x60,0x64 irq 1,12
[ 1.346601] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 1.347624] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.347820] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 1.348096] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 1.348295] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 1.348494] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 1.376204] mice: PS/2 mouse device common for all mice
[ 1.376449] cpuidle: using governor ladder
[ 1.376597] cpuidle: using governor menu
[ 1.377309] TCP bic registered
[ 1.377442] NET: Registered protocol family 1
[ 1.377628] NET: Registered protocol family 17
[ 1.378001] registered taskstats version 1
[ 1.378295] Freeing unused kernel memory: 372k freed
[ 1.399989] input: AT Translated Set 2 keyboard as /class/input/input1
[ 1.659605] ACPI: Transitioning device [C3B1] to D3
[ 1.660179] ACPI: PNP0C0B:00 is registered as cooling_device0
[ 1.664119] ACPI: Fan [C3B1] (off)
[ 1.668528] ACPI: Transitioning device [C3B2] to D3
[ 1.672174] ACPI: PNP0C0B:01 is registered as cooling_device1
[ 1.676120] ACPI: Fan [C3B2] (off)
[ 1.684489] ACPI: Transitioning device [C3C8] to D3
[ 1.688170] ACPI: PNP0C0B:02 is registered as cooling_device2
[ 1.692123] ACPI: Fan [C3C8] (off)
[ 1.700401] ACPI: Transitioning device [C3C9] to D3
[ 1.704170] ACPI: PNP0C0B:03 is registered as cooling_device3
[ 1.708123] ACPI: Fan [C3C9] (off)
[ 1.712504] ACPI: Transitioning device [C3CA] to D3
[ 1.716168] ACPI: PNP0C0B:04 is registered as cooling_device4
[ 1.720122] ACPI: Fan [C3CA] (off)
[ 1.724507] ACPI: Transitioning device [C3CB] to D3
[ 1.728169] ACPI: PNP0C0B:05 is registered as cooling_device5
[ 1.732123] ACPI: Fan [C3CB] (off)
[ 1.736503] ACPI: Transitioning device [C3CC] to D3
[ 1.740172] ACPI: PNP0C0B:06 is registered as cooling_device6
[ 1.744124] ACPI: Fan [C3CC] (off)
[ 2.036874] ACPI: SSDT 7F7DBCCA, 023D (r1 HP Cpu0Ist 3000 INTL 20060317)
[ 2.044353] ACPI: SSDT 7F7DBF8C, 05FA (r1 HP Cpu0Cst 3001 INTL 20060317)
[ 2.063554] Monitor-Mwait will be used to enter C-1 state
[ 2.063559] Monitor-Mwait will be used to enter C-2 state
[ 2.063747] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 2.064195] ACPI: ACPI0007:00 is registered as cooling_device7
[ 2.068141] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 2.072645] ACPI: SSDT 7F7DBC02, 00C8 (r1 HP Cpu1Ist 3000 INTL 20060317)
[ 2.080594] ACPI: SSDT 7F7DBF07, 0085 (r1 HP Cpu1Cst 3000 INTL 20060317)
[ 1.818884] ACPI: CPU1 (power states: C1[C1] C2[C2])
[ 2.088136] Marking TSC unstable due to TSC halts in idle
[ 1.820183] ACPI: ACPI0007:01 is registered as cooling_device8
[ 1.820189] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 1.844627] ACPI: LNXTHERM:01 is registered as thermal_zone0
[ 1.848462] ACPI: Thermal Zone [TZ6] (25 C)
[ 2.133204] ACPI: LNXTHERM:02 is registered as thermal_zone1
[ 1.895555] ACPI: Thermal Zone [TZ0] (69 C)
[ 1.904035] ACPI: LNXTHERM:03 is registered as thermal_zone2
[ 1.912215] ACPI: Thermal Zone [TZ1] (73 C)
[ 1.924119] ACPI: LNXTHERM:04 is registered as thermal_zone3
[ 1.932424] ACPI: Thermal Zone [TZ3] (61 C)
[ 1.945357] ACPI: LNXTHERM:05 is registered as thermal_zone4
[ 2.230054] ACPI: Thermal Zone [TZ4] (35 C)
[ 1.967135] ACPI: LNXTHERM:06 is registered as thermal_zone5
[ 2.246884] ACPI: Thermal Zone [TZ5] (63 C)
[ 2.727107] USB Universal Host Controller Interface driver v3.0
[ 2.730996] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 2.734941] PCI: Setting latency timer of device 0000:00:1a.0 to 64
[ 2.734948] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 2.739154] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 2.742973] uhci_hcd 0000:00:1a.0: irq 16, io base 0x00002040
[ 2.747136] usb usb1: configuration #1 chosen from 1 choice
[ 2.750983] hub 1-0:1.0: USB hub found
[ 2.754945] hub 1-0:1.0: 2 ports detected
[ 2.831253] Uniform Multi-Platform E-IDE driver
[ 2.834939] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 2.859089] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.862958] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.866938] usb usb1: Product: UHCI Host Controller
[ 2.870937] usb usb1: Manufacturer: Linux 2.6.25-rc7-amd64 uhci_hcd
[ 2.874938] usb usb1: SerialNumber: 0000:00:1a.0
[ 2.878987] ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 17 (level, low) -> IRQ 17
[ 2.882951] PCI: Setting latency timer of device 0000:00:1a.1 to 64
[ 2.882957] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 2.887042] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
[ 2.887088] uhci_hcd 0000:00:1a.1: irq 17, io base 0x00002060
[ 2.891130] usb usb2: configuration #1 chosen from 1 choice
[ 2.891168] hub 2-0:1.0: USB hub found
[ 2.894959] hub 2-0:1.0: 2 ports detected
[ 2.999077] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.002958] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.006959] usb usb2: Product: UHCI Host Controller
[ 3.010971] usb usb2: Manufacturer: Linux 2.6.25-rc7-amd64 uhci_hcd
[ 3.014959] usb usb2: SerialNumber: 0000:00:1a.1
[ 2.849465] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18
[ 2.853398] PCI: Setting latency timer of device 0000:00:1a.7 to 64
[ 2.853403] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 2.857463] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 3
[ 2.867014] ehci_hcd 0000:00:1a.7: debug port 1
[ 2.869385] PCI: cache line size of 32 is not supported by device 0000:00:1a.7
[ 2.869403] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xe0621000
[ 3.063182] usb 1-1: new full speed USB device using uhci_hcd and address 2
[ 2.996145] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 3.000261] usb usb3: configuration #1 chosen from 1 choice
[ 3.004169] hub 3-0:1.0: USB hub found
[ 3.008142] hub 3-0:1.0: 4 ports detected
[ 3.119998] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.123906] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.127907] usb usb3: Product: EHCI Host Controller
[ 3.131906] usb usb3: Manufacturer: Linux 2.6.25-rc7-amd64 ehci_hcd
[ 3.135907] usb usb3: SerialNumber: 0000:00:1a.7
[ 3.139953] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 20
[ 3.143921] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 3.143928] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 3.397131] Clocksource tsc unstable (delta = -251353446 ns)
[ 3.147985] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
[ 3.157105] ehci_hcd 0000:00:1d.7: debug port 1
[ 3.159914] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 3.159927] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xe0628000
[ 3.178892] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 3.183005] usb usb4: configuration #1 chosen from 1 choice
[ 3.186920] hub 4-0:1.0: USB hub found
[ 3.190892] hub 4-0:1.0: 6 ports detected
[ 3.297767] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.301683] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.305682] usb usb4: Product: EHCI Host Controller
[ 3.309682] usb usb4: Manufacturer: Linux 2.6.25-rc7-amd64 ehci_hcd
[ 3.313682] usb usb4: SerialNumber: 0000:00:1d.7
[ 3.637689] usb 1-1: device not accepting address 2, error -71
[ 3.656617] ACPI: PCI Interrupt 0000:02:06.1[B] -> GSI 19 (level, low) -> IRQ 19
[ 3.362226] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 20
[ 3.365695] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 3.365701] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 3.369785] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[ 3.715333] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[e0101000-e01017ff] Max Packet=[2048] IR/IT contexts=[4/4]
[ 3.373736] uhci_hcd 0000:00:1d.0: irq 20, io base 0x00002080
[ 3.377850] usb usb5: configuration #1 chosen from 1 choice
[ 3.381722] hub 5-0:1.0: USB hub found
[ 3.385696] hub 5-0:1.0: 2 ports detected
[ 3.492732] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.496609] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.500607] usb usb5: Product: UHCI Host Controller
[ 3.504607] usb usb5: Manufacturer: Linux 2.6.25-rc7-amd64 uhci_hcd
[ 3.508626] usb usb5: SerialNumber: 0000:00:1d.0
[ 3.512660] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 22 (level, low) -> IRQ 22
[ 3.516619] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 3.516625] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 3.520681] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
[ 3.524650] uhci_hcd 0000:00:1d.1: irq 22, io base 0x000020a0
[ 3.528768] usb usb6: configuration #1 chosen from 1 choice
[ 3.532648] hub 6-0:1.0: USB hub found
[ 3.536616] hub 6-0:1.0: 2 ports detected
[ 3.643538] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.647442] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.651440] usb usb6: Product: UHCI Host Controller
[ 3.655440] usb usb6: Manufacturer: Linux 2.6.25-rc7-amd64 uhci_hcd
[ 3.659440] usb usb6: SerialNumber: 0000:00:1d.1
[ 3.663476] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 3.667447] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 3.667452] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 3.671505] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
[ 3.675477] uhci_hcd 0000:00:1d.2: irq 18, io base 0x000020c0
[ 3.679609] usb usb7: configuration #1 chosen from 1 choice
[ 3.683478] hub 7-0:1.0: USB hub found
[ 3.687448] hub 7-0:1.0: 2 ports detected
[ 3.794386] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.798293] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.802294] usb usb7: Product: UHCI Host Controller
[ 3.806293] usb usb7: Manufacturer: Linux 2.6.25-rc7-amd64 uhci_hcd
[ 3.810294] usb usb7: SerialNumber: 0000:00:1d.2
[ 4.369232] ICH8M: IDE controller (0x8086:0x2850 rev 0x03) at PCI slot 0000:00:1f.1
[ 4.373213] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 16 (level, low) -> IRQ 16
[ 4.377221] ICH8M: not 100% native mode: will probe irqs later
[ 4.381215] ICH8M: IDE port disabled
[ 4.385210] ide0: BM-DMA at 0x20e0-0x20e7, BIOS settings: hda:DMA, hdb:DMA
[ 4.389213] Probing IDE interface ide0...
[ 4.517239] usb 5-2: new full speed USB device using uhci_hcd and address 2
[ 4.685053] usb 5-2: configuration #1 chosen from 1 choice
[ 4.689430] usb 5-2: New USB device found, idVendor=08ff, idProduct=2580
[ 4.693073] usb 5-2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 4.697060] usb 5-2: Product: Fingerprint Sensor
[ 4.845355] hdb: MATSHITADVD-RAM UJ-842S, ATAPI CD/DVD-ROM drive
[ 4.935607] usb 1-1: new full speed USB device using uhci_hcd and address 4
[ 4.547224] ieee1394: Host added: ID:BUS[0-00:1023] GUID[001b249929010210]
[ 5.110456] usb 1-1: configuration #1 chosen from 1 choice
[ 5.116251] usb 1-1: New USB device found, idVendor=03f0, idProduct=171d
[ 5.118472] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 5.122467] usb 1-1: Product: HP Integrated Module
[ 5.126467] usb 1-1: Manufacturer: Broadcom Corp
[ 5.154925] hda: TOSHIBA MK8009GAH, ATA DISK drive
[ 5.158515] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[ 5.158583] hda: UDMA/100 mode selected
[ 5.162574] hdb: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[ 5.162864] hdb: MWDMA2 mode selected
[ 5.166784] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 5.205075] No dock devices found.
[ 5.217401] SCSI subsystem initialized
[ 5.230075] libata version 3.00 loaded.
[ 5.261441] hda: max request size: 128KiB
[ 5.262499] hda: 156301488 sectors (80026 MB), CHS=65535/16/63
[ 4.837806] hda: cache flushes supported
[ 4.841723] hda: hda1 hda2 hda3
[ 4.869295] hdb: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
[ 4.871706] Uniform CD-ROM driver Revision: 3.20
[ 5.834326] device-mapper: uevent: version 1.0.3
[ 5.837313] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@xxxxxxxxxx
[ 9.448581] PM: Starting manual resume from disk
[ 10.024594] kjournald starting. Commit interval 5 seconds
[ 9.587812] EXT3-fs: mounted filesystem with ordered data mode.
[ 13.877449] input: Power Button (FF) as /class/input/input2
[ 13.932865] ACPI: Power Button (FF) [PWRF]
[ 13.936949] input: Sleep Button (CM) as /class/input/input3
[ 13.996903] ACPI: Sleep Button (CM) [C2BF]
[ 14.000901] input: Lid Switch as /class/input/input4
[ 14.034130] ACPI: Lid Switch [C155]
[ 14.037456] ACPI: AC Adapter [C23B] (on-line)
[ 14.529020] agpgart: Detected an Intel 965GM Chipset.
[ 14.531741] agpgart: Detected 7676K stolen memory.
[ 14.552269] agpgart: AGP aperture is 256M @ 0xd0000000
[ 14.332884] ACPI: Battery Slot [C23D] (battery present)
[ 14.723619] ACPI: WMI: Mapper loaded
[ 14.769333] ACPI: device:02 is registered as cooling_device9
[ 14.772235] input: Video Bus as /class/input/input5
[ 14.822936] ACPI: Video Device [C09A] (multi-head: yes rom: no post: no)
[ 14.985624] e1000e: Intel(R) PRO/1000 Network Driver - 0.2.0
[ 14.986888] e1000e: Copyright (c) 1999-2007 Intel Corporation.
[ 14.990966] ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 22 (level, low) -> IRQ 22
[ 14.994901] PCI: Setting latency timer of device 0000:00:19.0 to 64
[ 15.145424] eth0: (PCI Express:2.5GB/s:Width x1) 00:1e:68:06:12:ee
[ 15.147010] eth0: Intel(R) PRO/1000 Network Connection
[ 15.150935] eth0: MAC: 4, PHY: 6, PBA No: ffffff-0ff
[ 15.280806] Bluetooth: Core ver 2.11
[ 15.343723] ricoh-mmc: Ricoh MMC Controller disabling driver
[ 15.346911] ricoh-mmc: Copyright(c) Philip Langdale
[ 15.015704] NET: Registered protocol family 31
[ 15.015708] Bluetooth: HCI device and connection manager initialized
[ 15.015715] Bluetooth: HCI socket layer initialized
[ 15.350955] ricoh-mmc: Ricoh MMC controller found at 0000:02:06.3 [1180:0843] (rev 11)
[ 15.354932] ricoh-mmc: Controller is now disabled.
[ 15.163604] Bluetooth: HCI USB driver ver 2.9
[ 15.169669] usbcore: registered new interface driver hci_usb
[ 15.192659] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
[ 15.192994] iTCO_wdt: Found a ICH8M-E TCO device (Version=2, TCOBASE=0x1060)
[ 15.196925] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 15.302792] input: PC Speaker as /class/input/input6
[ 15.608570] sdhci: Secure Digital Host Controller Interface driver
[ 15.610702] sdhci: Copyright(c) Pierre Ossman
[ 15.614728] sdhci: SDHCI controller found at 0000:02:06.2 [1180:0822] (rev 21)
[ 15.618721] ACPI: PCI Interrupt 0000:02:06.2[C] -> GSI 20 (level, low) -> IRQ 20
[ 15.622714] sdhc0:slot0: Will use DMA mode even though HW doesn't fully claim to support it.
[ 15.626748] mmc0: SDHCI at 0xe0102000 irq 20 DMA
[ 16.253707] pnp: the driver 'tpm_inf_pnp' has been registered
[ 16.255095] tpm_inf_pnp 00:02: Found C284 with ID IFX0102
[ 16.259146] tpm_inf_pnp 00:02: TPM found: config base 0x560, data base 0x570, chip version 0x000b, vendor id 0x15d1 (Infineon), product id 0x000b (SLB 9635 TT 1.2)
[ 16.263442] tpm_inf_pnp 00:02: driver attached
[ 15.963006] Yenta: CardBus bridge found at 0000:02:06.0 [103c:30c9]
[ 16.394350] iwl4965: Intel(R) Wireless WiFi Link 4965AGN driver for Linux, 1.2.23ks
[ 16.397187] iwl4965: Copyright(c) 2003-2007 Intel Corporation
[ 16.090278] input: PS/2 Generic Mouse as /class/input/input7
[ 16.425826] Yenta: ISA IRQ mask 0x04b8, PCI irq 18
[ 16.428809] Socket status: 30000006
[ 16.432779] Yenta: Raising subordinate bus# of parent bus (#02) from #03 to #06
[ 16.436774] pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff
[ 16.440794] pcmcia: parent PCI bridge Memory window: 0xe0100000 - 0xe03fffff
[ 16.444784] pcmcia: parent PCI bridge Memory window: 0x88000000 - 0x8bffffff
[ 16.470454] ACPI: PCI Interrupt 0000:10:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 16.472812] PCI: Setting latency timer of device 0000:10:00.0 to 64
[ 16.476799] iwl4965: Detected Intel Wireless WiFi Link 4965AGN
[ 16.529555] iwl4965: Tunable channels: 13 802.11bg, 19 802.11a channels
[ 16.537188] phy0: Selected rate control algorithm 'iwl-4965-rs'
[ 16.294817] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 16.295965] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 16.400616] ACPI: PCI interrupt for device 0000:10:00.0 disabled
[ 16.868692] Synaptics Touchpad, model: 1, fw: 6.3, id: 0x1a0b1, caps: 0xa04713/0x200000
[ 16.908830] input: SynPS/2 Synaptics TouchPad as /class/input/input8
[ 18.454284] hda_intel: azx_get_response timeout, switching to polling mode: last cmd=0x006ba000
[ 19.882348] EXT3 FS on dm-1, internal journal
[ 21.291919] loop: module loaded
[ 21.106679] tun: Universal TUN/TAP device driver, 1.6
[ 21.107653] tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx>
[ 23.520274] kjournald starting. Commit interval 5 seconds
[ 23.217691] EXT3 FS on hda1, internal journal
[ 23.221385] EXT3-fs: mounted filesystem with ordered data mode.
[ 23.584565] kjournald starting. Commit interval 5 seconds
[ 23.264959] EXT3 FS on dm-3, internal journal
[ 23.264964] EXT3-fs: mounted filesystem with ordered data mode.
[ 23.337571] Adding 1048568k swap on /dev/mapper/lucky-swap. Priority:-1 extents:1 across:1048568k
[ 24.929768] Bridge firewalling registered
[ 24.931887] br0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
[ 24.942253] device eth0 entered promiscuous mode
[ 26.905730] eth0: Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[ 26.909306] eth0: 10/100 speed: disabling TSO
[ 26.913842] br0: port 1(eth0) entering learning state
[ 35.889487] br0: topology change detected, propagating
[ 35.893480] br0: port 1(eth0) entering forwarding state
[ 37.648095] NET: Registered protocol family 10
[ 37.649458] lo: Disabled Privacy Extensions
[ 45.122808] pnp: the driver 'parport_pc' has been registered
[ 44.888753] lp: driver loaded but no devices found
[ 44.998186] ppdev: user-space parallel port driver
[ 47.815704] br0: no IPv6 routers present
[ 48.150923] eth0: no IPv6 routers present
[ 50.699445] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
[ 53.780266] Bluetooth: L2CAP ver 2.9
[ 53.780796] Bluetooth: L2CAP socket layer initialized
[ 53.784394] Bluetooth: RFCOMM socket layer initialized
[ 53.784886] Bluetooth: RFCOMM TTY layer initialized
[ 53.788909] Bluetooth: RFCOMM ver 1.8
[ 54.139106] ACPI: PCI Interrupt 0000:10:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 54.140587] PM: Writing back config space on device 0000:10:00.0 at offset 1 (was 100002, writing 100006)
[ 54.355094] iwl4965: iwlwifi-4965-1.ucode firmware file req failed: Reason -2
[ 54.357637] iwl4965: Could not read microcode: -2
[ 54.361727] ACPI: PCI interrupt for device 0000:10:00.0 disabled
[ 57.567349] ACPI: PCI Interrupt 0000:10:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 57.575109] PM: Writing back config space on device 0000:10:00.0 at offset 1 (was 100002, writing 100006)
[ 57.587756] iwl4965: iwlwifi-4965-1.ucode firmware file req failed: Reason -2
[ 57.591080] iwl4965: Could not read microcode: -2
[ 57.595168] ACPI: PCI interrupt for device 0000:10:00.0 disabled
[ 58.260886] hdb: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
[ 58.262502] hdb: task_no_data_intr: error=0x04 { AbortedCommand }
[ 58.262502] ide: failed opcode was: 0xef
[ 62.410686] [drm] Initialized drm 1.1.0 20060810
[ 62.435748] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 62.435768] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 62.436019] [drm] Initialized i915 1.6.0 20060119 on minor 0
[ 71.634881] eth0: no IPv6 routers present
[ 79.545124] ACPI: PCI Interrupt 0000:10:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 79.545247] PM: Writing back config space on device 0000:10:00.0 at offset 1 (was 100002, writing 100006)
[ 79.553765] iwl4965: iwlwifi-4965-1.ucode firmware file req failed: Reason -2
[ 79.553778] iwl4965: Could not read microcode: -2
[ 79.553862] ACPI: PCI interrupt for device 0000:10:00.0 disabled
[ 101.471941] ACPI: PCI Interrupt 0000:10:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 101.472056] PM: Writing back config space on device 0000:10:00.0 at offset 1 (was 100002, writing 100006)
[ 101.480593] iwl4965: iwlwifi-4965-1.ucode firmware file req failed: Reason -2
[ 101.480604] iwl4965: Could not read microcode: -2
[ 101.480689] ACPI: PCI interrupt for device 0000:10:00.0 disabled
[ 123.396260] ACPI: PCI Interrupt 0000:10:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 123.397988] PM: Writing back config space on device 0000:10:00.0 at offset 1 (was 100002, writing 100006)
[ 123.408407] iwl4965: iwlwifi-4965-1.ucode firmware file req failed: Reason -2
[ 123.410141] iwl4965: Could not read microcode: -2
[ 123.412117] ACPI: PCI interrupt for device 0000:10:00.0 disabled
[ 145.351857] ACPI: PCI Interrupt 0000:10:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 145.355243] PM: Writing back config space on device 0000:10:00.0 at offset 1 (was 100002, writing 100006)
[ 145.366199] iwl4965: iwlwifi-4965-1.ucode firmware file req failed: Reason -2
[ 145.367590] iwl4965: Could not read microcode: -2
[ 145.371657] ACPI: PCI interrupt for device 0000:10:00.0 disabled
[ 167.313265] ACPI: PCI Interrupt 0000:10:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 167.317069] PM: Writing back config space on device 0000:10:00.0 at offset 1 (was 100002, writing 100006)
[ 167.329391] iwl4965: iwlwifi-4965-1.ucode firmware file req failed: Reason -2
[ 167.332981] iwl4965: Could not read microcode: -2
[ 167.337053] ACPI: PCI interrupt for device 0000:10:00.0 disabled
[ 189.276942] ACPI: PCI Interrupt 0000:10:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 189.280762] PM: Writing back config space on device 0000:10:00.0 at offset 1 (was 100002, writing 100006)
[ 189.293392] iwl4965: iwlwifi-4965-1.ucode firmware file req failed: Reason -2
[ 189.296665] iwl4965: Could not read microcode: -2
[ 189.300750] ACPI: PCI interrupt for device 0000:10:00.0 disabled
[ 310.719289] ACPI: PCI Interrupt 0000:10:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 310.723113] PM: Writing back config space on device 0000:10:00.0 at offset 1 (was 100002, writing 100006)
[ 310.735538] iwl4965: iwlwifi-4965-1.ucode firmware file req failed: Reason -2
[ 310.739063] iwl4965: Could not read microcode: -2
[ 310.743095] ACPI: PCI interrupt for device 0000:10:00.0 disabled
[ 432.148269] ACPI: PCI Interrupt 0000:10:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 432.152137] PM: Writing back config space on device 0000:10:00.0 at offset 1 (was 100002, writing 100006)
[ 432.164698] iwl4965: iwlwifi-4965-1.ucode firmware file req failed: Reason -2
[ 432.168023] iwl4965: Could not read microcode: -2
[ 432.172103] ACPI: PCI interrupt for device 0000:10:00.0 disabled
[ 553.578398] ACPI: PCI Interrupt 0000:10:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 553.581812] PM: Writing back config space on device 0000:10:00.0 at offset 1 (was 100002, writing 100006)
[ 553.594944] iwl4965: iwlwifi-4965-1.ucode firmware file req failed: Reason -2
[ 553.598044] iwl4965: Could not read microcode: -2
[ 553.602126] ACPI: PCI interrupt for device 0000:10:00.0 disabled
[ 675.019326] ACPI: PCI Interrupt 0000:10:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 675.022850] PM: Writing back config space on device 0000:10:00.0 at offset 1 (was 100002, writing 100006)
[ 675.033922] iwl4965: iwlwifi-4965-1.ucode firmware file req failed: Reason -2
[ 675.035057] iwl4965: Could not read microcode: -2
[ 675.039158] ACPI: PCI interrupt for device 0000:10:00.0 disabled
[ 796.455782] ACPI: PCI Interrupt 0000:10:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 796.459614] PM: Writing back config space on device 0000:10:00.0 at offset 1 (was 100002, writing 100006)
[ 796.472347] iwl4965: iwlwifi-4965-1.ucode firmware file req failed: Reason -2
[ 796.475569] iwl4965: Could not read microcode: -2
[ 796.479596] ACPI: PCI interrupt for device 0000:10:00.0 disabled
[ 895.455783] irq 19: nobody cared (try booting with the "irqpoll" option)
[ 895.455783] Pid: 0, comm: swapper Not tainted 2.6.25-rc7-amd64 #1
[ 895.455783]
[ 895.455783] Call Trace:
[ 895.455783] <IRQ> [<ffffffff88078155>] :ohci1394:ohci_irq_handler+0x4b/0x76e
[ 895.455783] [<ffffffff8026c883>] __report_bad_irq+0x30/0x72
[ 895.455783] [<ffffffff8026cac2>] note_interrupt+0x1fd/0x23f
[ 895.455783] [<ffffffff8026d34f>] handle_fasteoi_irq+0xa5/0xc8
[ 895.455783] [<ffffffff8020f53c>] do_IRQ+0x6d/0xd9
[ 895.455783] [<ffffffff8020c46d>] ret_from_intr+0x0/0x19
[ 895.455783] <EOI> [<ffffffff803a25a4>] menu_reflect+0x0/0x75
[ 895.455783] [<ffffffff8800642b>] :processor:acpi_idle_enter_simple+0x18d/0x1fe
[ 895.455783] [<ffffffff803a1b2b>] cpuidle_idle_call+0x7a/0xb3
[ 895.455783] [<ffffffff803a1ab1>] cpuidle_idle_call+0x0/0xb3
[ 895.455783] [<ffffffff8020b06c>] cpu_idle+0xa9/0xd3
[ 895.455783]
[ 895.455783] handlers:
[ 895.455783] [<ffffffff8807810a>] (ohci_irq_handler+0x0/0x76e [ohci1394])
[ 895.455783] Disabling IRQ #19
[ 917.880795] ACPI: PCI Interrupt 0000:10:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 917.884259] PM: Writing back config space on device 0000:10:00.0 at offset 1 (was 100002, writing 100006)
[ 917.892669] iwl4965: iwlwifi-4965-1.ucode firmware file req failed: Reason -2
[ 917.896083] iwl4965: Could not read microcode: -2
[ 917.896641] ACPI: PCI interrupt for device 0000:10:00.0 disabled