[PATCH 07/70] esp: use tty_port

From: Alan Cox
Date: Fri Jun 20 2008 - 16:17:58 EST

From: Alan Cox <alan@xxxxxxxxxx>

Switch esp to use the new tty_port structures

Signed-off-by: Alan Cox <alan@xxxxxxxxxx>
---

drivers/char/esp.c | 272 +++++++++++++++++++++++-----------------------
include/linux/hayesesp.h | 9 --
2 files changed, 138 insertions(+), 143 deletions(-)


diff --git a/drivers/char/esp.c b/drivers/char/esp.c
index 84840ba..2eaf09f 100644
--- a/drivers/char/esp.c
+++ b/drivers/char/esp.c
@@ -128,9 +128,9 @@ static struct tty_driver *esp_driver;

#if defined(MODULE) && defined(SERIAL_DEBUG_MCOUNT)
#define DBG_CNT(s) printk(KERN_DEBUG "(%s): [%x] refc=%d, serc=%d, ttyc=%d -> %s\n", \
- tty->name, info->flags, \
+ tty->name, info->port.flags, \
serial_driver.refcount, \
- info->count, tty->count, s)
+ info->port.count, tty->count, s)
#else
#define DBG_CNT(s)
#endif
@@ -172,13 +172,13 @@ static inline int serial_paranoia_check(struct esp_struct *info,

static inline unsigned int serial_in(struct esp_struct *info, int offset)
{
- return inb(info->port + offset);
+ return inb(info->io_port + offset);
}

static inline void serial_out(struct esp_struct *info, int offset,
unsigned char value)
{
- outb(value, info->port+offset);
+ outb(value, info->io_port+offset);
}

/*
@@ -273,7 +273,7 @@ static inline void release_pio_buffer(struct esp_pio_buffer *buf)

static inline void receive_chars_pio(struct esp_struct *info, int num_bytes)
{
- struct tty_struct *tty = info->tty;
+ struct tty_struct *tty = info->port.tty;
int i;
struct esp_pio_buffer *pio_buf;
struct esp_pio_buffer *err_buf;
@@ -295,7 +295,7 @@ static inline void receive_chars_pio(struct esp_struct *info, int num_bytes)

for (i = 0; i < num_bytes - 1; i += 2) {
*((unsigned short *)(pio_buf->data + i)) =
- inw(info->port + UART_ESI_RX);
+ inw(info->io_port + UART_ESI_RX);
err_buf->data[i] = serial_in(info, UART_ESI_RWS);
err_buf->data[i + 1] = (err_buf->data[i] >> 3) & status_mask;
err_buf->data[i] &= status_mask;
@@ -308,7 +308,7 @@ static inline void receive_chars_pio(struct esp_struct *info, int num_bytes)
}

/* make sure everything is still ok since interrupts were enabled */
- tty = info->tty;
+ tty = info->port.tty;

if (!tty) {
release_pio_buffer(pio_buf);
@@ -325,7 +325,7 @@ static inline void receive_chars_pio(struct esp_struct *info, int num_bytes)

if (err_buf->data[i] & 0x04) {
flag = TTY_BREAK;
- if (info->flags & ASYNC_SAK)
+ if (info->port.flags & ASYNC_SAK)
do_SAK(tty);
} else if (err_buf->data[i] & 0x02)
flag = TTY_FRAME;
@@ -370,7 +370,7 @@ static void receive_chars_dma(struct esp_struct *info, int num_bytes)
static inline void receive_chars_dma_done(struct esp_struct *info,
int status)
{
- struct tty_struct *tty = info->tty;
+ struct tty_struct *tty = info->port.tty;
int num_bytes;
unsigned long flags;

@@ -396,7 +396,7 @@ static inline void receive_chars_dma_done(struct esp_struct *info,
if (status & 0x10) {
statflag = TTY_BREAK;
(info->icount.brk)++;
- if (info->flags & ASYNC_SAK)
+ if (info->port.flags & ASYNC_SAK)
do_SAK(tty);
} else if (status & 0x08) {
statflag = TTY_FRAME;
@@ -451,7 +451,7 @@ static inline void transmit_chars_pio(struct esp_struct *info,

for (i = 0; i < space_avail - 1; i += 2) {
outw(*((unsigned short *)(pio_buf->data + i)),
- info->port + UART_ESI_TX);
+ info->io_port + UART_ESI_TX);
}

if (space_avail & 0x0001)
@@ -470,8 +470,8 @@ static inline void transmit_chars_pio(struct esp_struct *info,
}

if (info->xmit_cnt < WAKEUP_CHARS) {
- if (info->tty)
- tty_wakeup(info->tty);
+ if (info->port.tty)
+ tty_wakeup(info->port.tty);

#ifdef SERIAL_DEBUG_INTR
printk("THRE...");
@@ -507,8 +507,8 @@ static inline void transmit_chars_dma(struct esp_struct *info, int num_bytes)
info->xmit_tail = (info->xmit_tail + dma_bytes) & (ESP_XMIT_SIZE - 1);

if (info->xmit_cnt < WAKEUP_CHARS) {
- if (info->tty)
- tty_wakeup(info->tty);
+ if (info->port.tty)
+ tty_wakeup(info->port.tty);

#ifdef SERIAL_DEBUG_INTR
printk("THRE...");
@@ -575,18 +575,18 @@ static void check_modem_status(struct esp_struct *info)
wake_up_interruptible(&info->delta_msr_wait);
}

- if ((info->flags & ASYNC_CHECK_CD) && (status & UART_MSR_DDCD)) {
+ if ((info->port.flags & ASYNC_CHECK_CD) && (status & UART_MSR_DDCD)) {
#if (defined(SERIAL_DEBUG_OPEN) || defined(SERIAL_DEBUG_INTR))
printk("ttys%d CD now %s...", info->line,
(status & UART_MSR_DCD) ? "on" : "off");
#endif
if (status & UART_MSR_DCD)
- wake_up_interruptible(&info->open_wait);
+ wake_up_interruptible(&info->port.open_wait);
else {
#ifdef SERIAL_DEBUG_OPEN
printk("scheduling hangup...");
#endif
- tty_hangup(info->tty);
+ tty_hangup(info->port.tty);
}
}
}
@@ -609,7 +609,7 @@ static irqreturn_t rs_interrupt_single(int irq, void *dev_id)

spin_lock(&info->lock);

- if (!info->tty) {
+ if (!info->port.tty) {
spin_unlock(&info->lock);
return IRQ_NONE;
}
@@ -647,7 +647,7 @@ static irqreturn_t rs_interrupt_single(int irq, void *dev_id)
num_bytes = serial_in(info, UART_ESI_STAT1) << 8;
num_bytes |= serial_in(info, UART_ESI_STAT2);

- num_bytes = tty_buffer_request_room(info->tty, num_bytes);
+ num_bytes = tty_buffer_request_room(info->port.tty, num_bytes);

if (num_bytes) {
if (dma_bytes ||
@@ -661,7 +661,7 @@ static irqreturn_t rs_interrupt_single(int irq, void *dev_id)

if (!(info->stat_flags & (ESP_STAT_DMA_RX | ESP_STAT_DMA_TX)) &&
(scratch & 0x02) && (info->IER & UART_IER_THRI)) {
- if ((info->xmit_cnt <= 0) || info->tty->stopped) {
+ if ((info->xmit_cnt <= 0) || info->port.tty->stopped) {
info->IER &= ~UART_IER_THRI;
serial_out(info, UART_ESI_CMD1, ESI_SET_SRV_MASK);
serial_out(info, UART_ESI_CMD2, info->IER);
@@ -782,7 +782,7 @@ static int startup(struct esp_struct *info)

spin_lock_irqsave(&info->lock, flags);

- if (info->flags & ASYNC_INITIALIZED)
+ if (info->port.flags & ASYNC_INITIALIZED)
goto out;

if (!info->xmit_buf) {
@@ -806,7 +806,7 @@ static int startup(struct esp_struct *info)
num_chars |= serial_in(info, UART_ESI_STAT2);

while (num_chars > 1) {
- inw(info->port + UART_ESI_RX);
+ inw(info->io_port + UART_ESI_RX);
num_chars -= 2;
}

@@ -834,9 +834,9 @@ static int startup(struct esp_struct *info)

if (retval) {
if (capable(CAP_SYS_ADMIN)) {
- if (info->tty)
+ if (info->port.tty)
set_bit(TTY_IO_ERROR,
- &info->tty->flags);
+ &info->port.tty->flags);
retval = 0;
}
goto out_unlocked;
@@ -874,30 +874,30 @@ static int startup(struct esp_struct *info)
serial_out(info, UART_ESI_CMD1, ESI_SET_SRV_MASK);
serial_out(info, UART_ESI_CMD2, info->IER);

- if (info->tty)
- clear_bit(TTY_IO_ERROR, &info->tty->flags);
+ if (info->port.tty)
+ clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
spin_unlock_irqrestore(&info->lock, flags);

/*
* Set up the tty->alt_speed kludge
*/
- if (info->tty) {
- if ((info->flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI)
- info->tty->alt_speed = 57600;
- if ((info->flags & ASYNC_SPD_MASK) == ASYNC_SPD_VHI)
- info->tty->alt_speed = 115200;
- if ((info->flags & ASYNC_SPD_MASK) == ASYNC_SPD_SHI)
- info->tty->alt_speed = 230400;
- if ((info->flags & ASYNC_SPD_MASK) == ASYNC_SPD_WARP)
- info->tty->alt_speed = 460800;
+ if (info->port.tty) {
+ if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI)
+ info->port.tty->alt_speed = 57600;
+ if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_VHI)
+ info->port.tty->alt_speed = 115200;
+ if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_SHI)
+ info->port.tty->alt_speed = 230400;
+ if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_WARP)
+ info->port.tty->alt_speed = 460800;
}

/*
* set the speed of the serial port
*/
change_speed(info);
- info->flags |= ASYNC_INITIALIZED;
+ info->port.flags |= ASYNC_INITIALIZED;
return 0;

out:
@@ -914,7 +914,7 @@ static void shutdown(struct esp_struct *info)
{
unsigned long flags, f;

- if (!(info->flags & ASYNC_INITIALIZED))
+ if (!(info->port.flags & ASYNC_INITIALIZED))
return;

#ifdef SERIAL_DEBUG_OPEN
@@ -951,7 +951,7 @@ static void shutdown(struct esp_struct *info)

while (current_port) {
if ((current_port != info) &&
- (current_port->flags & ASYNC_INITIALIZED))
+ (current_port->port.flags & ASYNC_INITIALIZED))
break;

current_port = current_port->next_port;
@@ -974,7 +974,7 @@ static void shutdown(struct esp_struct *info)
serial_out(info, UART_ESI_CMD1, ESI_SET_SRV_MASK);
serial_out(info, UART_ESI_CMD2, 0x00);

- if (!info->tty || (info->tty->termios->c_cflag & HUPCL))
+ if (!info->port.tty || (info->port.tty->termios->c_cflag & HUPCL))
info->MCR &= ~(UART_MCR_DTR|UART_MCR_RTS);

info->MCR &= ~UART_MCR_OUT2;
@@ -982,10 +982,10 @@ static void shutdown(struct esp_struct *info)
serial_out(info, UART_ESI_CMD2, UART_MCR);
serial_out(info, UART_ESI_CMD2, info->MCR);

- if (info->tty)
- set_bit(TTY_IO_ERROR, &info->tty->flags);
+ if (info->port.tty)
+ set_bit(TTY_IO_ERROR, &info->port.tty->flags);

- info->flags &= ~ASYNC_INITIALIZED;
+ info->port.flags &= ~ASYNC_INITIALIZED;
spin_unlock_irqrestore(&info->lock, flags);
}

@@ -1002,10 +1002,10 @@ static void change_speed(struct esp_struct *info)
unsigned char flow1 = 0, flow2 = 0;
unsigned long flags;

- if (!info->tty || !info->tty->termios)
+ if (!info->port.tty || !info->port.tty->termios)
return;
- cflag = info->tty->termios->c_cflag;
- port = info->port;
+ cflag = info->port.tty->termios->c_cflag;
+ port = info->io_port;

/* byte size and parity */
switch (cflag & CSIZE) {
@@ -1029,9 +1029,9 @@ static void change_speed(struct esp_struct *info)
if (cflag & CMSPAR)
cval |= UART_LCR_SPAR;
#endif
- baud = tty_get_baud_rate(info->tty);
+ baud = tty_get_baud_rate(info->port.tty);
if (baud == 38400 &&
- ((info->flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST))
+ ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST))
quot = info->custom_divisor;
else {
if (baud == 134) /* Special case since 134 is really 134.5 */
@@ -1046,49 +1046,49 @@ static void change_speed(struct esp_struct *info)
if (baud) {
/* Actual rate */
baud = BASE_BAUD/quot;
- tty_encode_baud_rate(info->tty, baud, baud);
+ tty_encode_baud_rate(info->port.tty, baud, baud);
}
info->timeout = ((1024 * HZ * bits * quot) / BASE_BAUD) + (HZ / 50);

/* CTS flow control flag and modem status interrupts */
/* info->IER &= ~UART_IER_MSI; */
if (cflag & CRTSCTS) {
- info->flags |= ASYNC_CTS_FLOW;
+ info->port.flags |= ASYNC_CTS_FLOW;
/* info->IER |= UART_IER_MSI; */
flow1 = 0x04;
flow2 = 0x10;
} else
- info->flags &= ~ASYNC_CTS_FLOW;
+ info->port.flags &= ~ASYNC_CTS_FLOW;
if (cflag & CLOCAL)
- info->flags &= ~ASYNC_CHECK_CD;
+ info->port.flags &= ~ASYNC_CHECK_CD;
else
- info->flags |= ASYNC_CHECK_CD;
+ info->port.flags |= ASYNC_CHECK_CD;

/*
* Set up parity check flag
*/
info->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
- if (I_INPCK(info->tty))
+ if (I_INPCK(info->port.tty))
info->read_status_mask |= UART_LSR_FE | UART_LSR_PE;
- if (I_BRKINT(info->tty) || I_PARMRK(info->tty))
+ if (I_BRKINT(info->port.tty) || I_PARMRK(info->port.tty))
info->read_status_mask |= UART_LSR_BI;

info->ignore_status_mask = 0;
#if 0
/* This should be safe, but for some broken bits of hardware... */
- if (I_IGNPAR(info->tty)) {
+ if (I_IGNPAR(info->port.tty)) {
info->ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
info->read_status_mask |= UART_LSR_PE | UART_LSR_FE;
}
#endif
- if (I_IGNBRK(info->tty)) {
+ if (I_IGNBRK(info->port.tty)) {
info->ignore_status_mask |= UART_LSR_BI;
info->read_status_mask |= UART_LSR_BI;
/*
* If we're ignore parity and break indicators, ignore
* overruns too. (For real raw support).
*/
- if (I_IGNPAR(info->tty)) {
+ if (I_IGNPAR(info->port.tty)) {
info->ignore_status_mask |= UART_LSR_OE | \
UART_LSR_PE | UART_LSR_FE;
info->read_status_mask |= UART_LSR_OE | \
@@ -1096,7 +1096,7 @@ static void change_speed(struct esp_struct *info)
}
}

- if (I_IXOFF(info->tty))
+ if (I_IXOFF(info->port.tty))
flow1 |= 0x81;

spin_lock_irqsave(&info->lock, flags);
@@ -1116,10 +1116,10 @@ static void change_speed(struct esp_struct *info)
serial_out(info, UART_ESI_CMD2, flow2);

/* set flow control characters (XON/XOFF only) */
- if (I_IXOFF(info->tty)) {
+ if (I_IXOFF(info->port.tty)) {
serial_out(info, UART_ESI_CMD1, ESI_SET_FLOW_CHARS);
- serial_out(info, UART_ESI_CMD2, START_CHAR(info->tty));
- serial_out(info, UART_ESI_CMD2, STOP_CHAR(info->tty));
+ serial_out(info, UART_ESI_CMD2, START_CHAR(info->port.tty));
+ serial_out(info, UART_ESI_CMD2, STOP_CHAR(info->port.tty));
serial_out(info, UART_ESI_CMD2, 0x10);
serial_out(info, UART_ESI_CMD2, 0x21);
switch (cflag & CSIZE) {
@@ -1355,9 +1355,9 @@ static int get_serial_info(struct esp_struct *info,
memset(&tmp, 0, sizeof(tmp));
tmp.type = PORT_16550A;
tmp.line = info->line;
- tmp.port = info->port;
+ tmp.port = info->io_port;
tmp.irq = info->irq;
- tmp.flags = info->flags;
+ tmp.flags = info->port.flags;
tmp.xmit_fifo_size = 1024;
tmp.baud_base = BASE_BAUD;
tmp.close_delay = info->close_delay;
@@ -1407,7 +1407,7 @@ static int set_serial_info(struct esp_struct *info,

if ((new_serial.type != PORT_16550A) ||
(new_serial.hub6) ||
- (info->port != new_serial.port) ||
+ (info->io_port != new_serial.port) ||
(new_serial.baud_base != BASE_BAUD) ||
(new_serial.irq > 15) ||
(new_serial.irq < 2) ||
@@ -1425,9 +1425,9 @@ static int set_serial_info(struct esp_struct *info,
if (change_irq ||
(new_serial.close_delay != info->close_delay) ||
((new_serial.flags & ~ASYNC_USR_MASK) !=
- (info->flags & ~ASYNC_USR_MASK)))
+ (info->port.flags & ~ASYNC_USR_MASK)))
return -EPERM;
- info->flags = ((info->flags & ~ASYNC_USR_MASK) |
+ info->port.flags = ((info->port.flags & ~ASYNC_USR_MASK) |
(new_serial.flags & ASYNC_USR_MASK));
info->custom_divisor = new_serial.custom_divisor;
} else {
@@ -1441,9 +1441,9 @@ static int set_serial_info(struct esp_struct *info,
if ((current_async->line >= info->line) &&
(current_async->line < (info->line + 8))) {
if (current_async == info) {
- if (current_async->count > 1)
+ if (current_async->port.count > 1)
return -EBUSY;
- } else if (current_async->count)
+ } else if (current_async->port.count)
return -EBUSY;
}

@@ -1456,7 +1456,7 @@ static int set_serial_info(struct esp_struct *info,
* At this point, we start making changes.....
*/

- info->flags = ((info->flags & ~ASYNC_FLAGS) |
+ info->port.flags = ((info->port.flags & ~ASYNC_FLAGS) |
(new_serial.flags & ASYNC_FLAGS));
info->custom_divisor = new_serial.custom_divisor;
info->close_delay = new_serial.close_delay * HZ/100;
@@ -1487,18 +1487,18 @@ static int set_serial_info(struct esp_struct *info,
}
}

- if (info->flags & ASYNC_INITIALIZED) {
- if (((old_info.flags & ASYNC_SPD_MASK) !=
- (info->flags & ASYNC_SPD_MASK)) ||
+ if (info->port.flags & ASYNC_INITIALIZED) {
+ if (((old_info.port.flags & ASYNC_SPD_MASK) !=
+ (info->port.flags & ASYNC_SPD_MASK)) ||
(old_info.custom_divisor != info->custom_divisor)) {
- if ((info->flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI)
- info->tty->alt_speed = 57600;
- if ((info->flags & ASYNC_SPD_MASK) == ASYNC_SPD_VHI)
- info->tty->alt_speed = 115200;
- if ((info->flags & ASYNC_SPD_MASK) == ASYNC_SPD_SHI)
- info->tty->alt_speed = 230400;
- if ((info->flags & ASYNC_SPD_MASK) == ASYNC_SPD_WARP)
- info->tty->alt_speed = 460800;
+ if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI)
+ info->port.tty->alt_speed = 57600;
+ if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_VHI)
+ info->port.tty->alt_speed = 115200;
+ if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_SHI)
+ info->port.tty->alt_speed = 230400;
+ if ((info->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_WARP)
+ info->port.tty->alt_speed = 460800;
change_speed(info);
}
} else
@@ -1554,9 +1554,9 @@ static int set_esp_config(struct esp_struct *info,

while (current_async) {
if (current_async == info) {
- if (current_async->count > 1)
+ if (current_async->port.count > 1)
return -EBUSY;
- } else if (current_async->count)
+ } else if (current_async->port.count)
return -EBUSY;

current_async = current_async->next_port;
@@ -1578,7 +1578,7 @@ static int set_esp_config(struct esp_struct *info,
spin_unlock_irqrestore(&info->lock, flags);
} else {
/* DMA mode to PIO mode only */
- if (info->count > 1)
+ if (info->port.count > 1)
return -EBUSY;

shutdown(info);
@@ -1634,7 +1634,7 @@ static int set_esp_config(struct esp_struct *info,
spin_unlock_irqrestore(&info->lock, flags);
}

- if (!(info->flags & ASYNC_INITIALIZED))
+ if (!(info->port.flags & ASYNC_INITIALIZED))
retval = startup(info);

return retval;
@@ -1917,9 +1917,9 @@ static void rs_close(struct tty_struct *tty, struct file *filp)

#ifdef SERIAL_DEBUG_OPEN
printk(KERN_DEBUG "rs_close ttys%d, count = %d\n",
- info->line, info->count);
+ info->line, info->port.count);
#endif
- if (tty->count == 1 && info->count != 1) {
+ if (tty->count == 1 && info->port.count != 1) {
/*
* Uh, oh. tty->count is 1, which means that the tty
* structure will be freed. Info->count should always
@@ -1927,19 +1927,19 @@ static void rs_close(struct tty_struct *tty, struct file *filp)
* one, we've got real problems, since it means the
* serial port won't be shutdown.
*/
- printk(KERN_DEBUG "rs_close: bad serial port count; tty->count is 1, info->count is %d\n", info->count);
- info->count = 1;
+ printk(KERN_DEBUG "rs_close: bad serial port count; tty->count is 1, info->port.count is %d\n", info->port.count);
+ info->port.count = 1;
}
- if (--info->count < 0) {
+ if (--info->port.count < 0) {
printk(KERN_ERR "rs_close: bad serial port count for ttys%d: %d\n",
- info->line, info->count);
- info->count = 0;
+ info->line, info->port.count);
+ info->port.count = 0;
}
- if (info->count) {
+ if (info->port.count) {
DBG_CNT("before DEC-2");
goto out;
}
- info->flags |= ASYNC_CLOSING;
+ info->port.flags |= ASYNC_CLOSING;

spin_unlock_irqrestore(&info->lock, flags);
/*
@@ -1958,7 +1958,7 @@ static void rs_close(struct tty_struct *tty, struct file *filp)
/* info->IER &= ~UART_IER_RLSI; */
info->IER &= ~UART_IER_RDI;
info->read_status_mask &= ~UART_LSR_DR;
- if (info->flags & ASYNC_INITIALIZED) {
+ if (info->port.flags & ASYNC_INITIALIZED) {

spin_lock_irqsave(&info->lock, flags);
serial_out(info, UART_ESI_CMD1, ESI_SET_SRV_MASK);
@@ -1981,15 +1981,15 @@ static void rs_close(struct tty_struct *tty, struct file *filp)
rs_flush_buffer(tty);
tty_ldisc_flush(tty);
tty->closing = 0;
- info->tty = NULL;
+ info->port.tty = NULL;

- if (info->blocked_open) {
+ if (info->port.blocked_open) {
if (info->close_delay)
msleep_interruptible(jiffies_to_msecs(info->close_delay));
- wake_up_interruptible(&info->open_wait);
+ wake_up_interruptible(&info->port.open_wait);
}
- info->flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CLOSING);
- wake_up_interruptible(&info->close_wait);
+ info->port.flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CLOSING);
+ wake_up_interruptible(&info->port.close_wait);
return;

out:
@@ -2047,10 +2047,10 @@ static void esp_hangup(struct tty_struct *tty)

rs_flush_buffer(tty);
shutdown(info);
- info->count = 0;
- info->flags &= ~ASYNC_NORMAL_ACTIVE;
- info->tty = NULL;
- wake_up_interruptible(&info->open_wait);
+ info->port.count = 0;
+ info->port.flags &= ~ASYNC_NORMAL_ACTIVE;
+ info->port.tty = NULL;
+ wake_up_interruptible(&info->port.open_wait);
}

/*
@@ -2071,11 +2071,11 @@ static int block_til_ready(struct tty_struct *tty, struct file *filp,
* until it's done, and then try again.
*/
if (tty_hung_up_p(filp) ||
- (info->flags & ASYNC_CLOSING)) {
- if (info->flags & ASYNC_CLOSING)
- interruptible_sleep_on(&info->close_wait);
+ (info->port.flags & ASYNC_CLOSING)) {
+ if (info->port.flags & ASYNC_CLOSING)
+ interruptible_sleep_on(&info->port.close_wait);
#ifdef SERIAL_DO_RESTART
- if (info->flags & ASYNC_HUP_NOTIFY)
+ if (info->port.flags & ASYNC_HUP_NOTIFY)
return -EAGAIN;
else
return -ERESTARTSYS;
@@ -2090,7 +2090,7 @@ static int block_til_ready(struct tty_struct *tty, struct file *filp,
*/
if ((filp->f_flags & O_NONBLOCK) ||
(tty->flags & (1 << TTY_IO_ERROR))) {
- info->flags |= ASYNC_NORMAL_ACTIVE;
+ info->port.flags |= ASYNC_NORMAL_ACTIVE;
return 0;
}

@@ -2100,20 +2100,20 @@ static int block_til_ready(struct tty_struct *tty, struct file *filp,
/*
* Block waiting for the carrier detect and the line to become
* free (i.e., not in use by the callout). While we are in
- * this loop, info->count is dropped by one, so that
+ * this loop, info->port.count is dropped by one, so that
* rs_close() knows when to free things. We restore it upon
* exit, either normal or abnormal.
*/
retval = 0;
- add_wait_queue(&info->open_wait, &wait);
+ add_wait_queue(&info->port.open_wait, &wait);
#ifdef SERIAL_DEBUG_OPEN
printk(KERN_DEBUG "block_til_ready before block: ttys%d, count = %d\n",
- info->line, info->count);
+ info->line, info->port.count);
#endif
spin_lock_irqsave(&info->lock, flags);
if (!tty_hung_up_p(filp))
- info->count--;
- info->blocked_open++;
+ info->port.count--;
+ info->port.blocked_open++;
while (1) {
if ((tty->termios->c_cflag & CBAUD)) {
unsigned int scratch;
@@ -2128,9 +2128,9 @@ static int block_til_ready(struct tty_struct *tty, struct file *filp,
}
set_current_state(TASK_INTERRUPTIBLE);
if (tty_hung_up_p(filp) ||
- !(info->flags & ASYNC_INITIALIZED)) {
+ !(info->port.flags & ASYNC_INITIALIZED)) {
#ifdef SERIAL_DO_RESTART
- if (info->flags & ASYNC_HUP_NOTIFY)
+ if (info->port.flags & ASYNC_HUP_NOTIFY)
retval = -EAGAIN;
else
retval = -ERESTARTSYS;
@@ -2144,7 +2144,7 @@ static int block_til_ready(struct tty_struct *tty, struct file *filp,
if (serial_in(info, UART_ESI_STAT2) & UART_MSR_DCD)
do_clocal = 1;

- if (!(info->flags & ASYNC_CLOSING) &&
+ if (!(info->port.flags & ASYNC_CLOSING) &&
(do_clocal))
break;
if (signal_pending(current)) {
@@ -2153,25 +2153,25 @@ static int block_til_ready(struct tty_struct *tty, struct file *filp,
}
#ifdef SERIAL_DEBUG_OPEN
printk(KERN_DEBUG "block_til_ready blocking: ttys%d, count = %d\n",
- info->line, info->count);
+ info->line, info->port.count);
#endif
spin_unlock_irqrestore(&info->lock, flags);
schedule();
spin_lock_irqsave(&info->lock, flags);
}
set_current_state(TASK_RUNNING);
- remove_wait_queue(&info->open_wait, &wait);
+ remove_wait_queue(&info->port.open_wait, &wait);
if (!tty_hung_up_p(filp))
- info->count++;
- info->blocked_open--;
+ info->port.count++;
+ info->port.blocked_open--;
spin_unlock_irqrestore(&info->lock, flags);
#ifdef SERIAL_DEBUG_OPEN
printk(KERN_DEBUG "block_til_ready after blocking: ttys%d, count = %d\n",
- info->line, info->count);
+ info->line, info->port.count);
#endif
if (retval)
return retval;
- info->flags |= ASYNC_NORMAL_ACTIVE;
+ info->port.flags |= ASYNC_NORMAL_ACTIVE;
return 0;
}

@@ -2204,12 +2204,12 @@ static int esp_open(struct tty_struct *tty, struct file *filp)
}

#ifdef SERIAL_DEBUG_OPEN
- printk(KERN_DEBUG "esp_open %s, count = %d\n", tty->name, info->count);
+ printk(KERN_DEBUG "esp_open %s, count = %d\n", tty->name, info->port.count);
#endif
spin_lock_irqsave(&info->lock, flags);
- info->count++;
+ info->port.count++;
tty->driver_data = info;
- info->tty = tty;
+ info->port.tty = tty;

spin_unlock_irqrestore(&info->lock, flags);

@@ -2263,7 +2263,7 @@ static int autoconfig(struct esp_struct *info)
int port_detected = 0;
unsigned long flags;

- if (!request_region(info->port, REGION_SIZE, "esp serial"))
+ if (!request_region(info->io_port, REGION_SIZE, "esp serial"))
return -EIO;

spin_lock_irqsave(&info->lock, flags);
@@ -2300,7 +2300,7 @@ static int autoconfig(struct esp_struct *info)
}
}
if (!port_detected)
- release_region(info->port, REGION_SIZE);
+ release_region(info->io_port, REGION_SIZE);

spin_unlock_irqrestore(&info->lock, flags);
return (port_detected);
@@ -2414,7 +2414,7 @@ static int __init espserial_init(void)
offset = 0;

do {
- info->port = esp[i] + offset;
+ info->io_port = esp[i] + offset;
info->irq = irq[i];
info->line = (i * 8) + (offset / 8);

@@ -2425,9 +2425,9 @@ static int __init espserial_init(void)
}

info->custom_divisor = (divisor[i] >> (offset / 2)) & 0xf;
- info->flags = STD_COM_FLAGS;
+ info->port.flags = STD_COM_FLAGS;
if (info->custom_divisor)
- info->flags |= ASYNC_SPD_CUST;
+ info->port.flags |= ASYNC_SPD_CUST;
info->magic = ESP_MAGIC;
info->close_delay = 5*HZ/10;
info->closing_wait = 30*HZ;
@@ -2436,13 +2436,13 @@ static int __init espserial_init(void)
info->config.flow_off = flow_off;
info->config.pio_threshold = pio_threshold;
info->next_port = ports;
- init_waitqueue_head(&info->open_wait);
- init_waitqueue_head(&info->close_wait);
+ init_waitqueue_head(&info->port.open_wait);
+ init_waitqueue_head(&info->port.close_wait);
init_waitqueue_head(&info->delta_msr_wait);
init_waitqueue_head(&info->break_wait);
ports = info;
printk(KERN_INFO "ttyP%d at 0x%04x (irq = %d) is an ESP ",
- info->line, info->port, info->irq);
+ info->line, info->io_port, info->irq);

if (info->line % 8) {
printk("secondary port\n");
@@ -2498,8 +2498,8 @@ static void __exit espserial_exit(void)
put_tty_driver(esp_driver);

while (ports) {
- if (ports->port)
- release_region(ports->port, REGION_SIZE);
+ if (ports->io_port)
+ release_region(ports->io_port, REGION_SIZE);
temp_async = ports->next_port;
kfree(ports);
ports = temp_async;
diff --git a/include/linux/hayesesp.h b/include/linux/hayesesp.h
index 2177ee5..940aeb5 100644
--- a/include/linux/hayesesp.h
+++ b/include/linux/hayesesp.h
@@ -76,11 +76,10 @@ struct hayes_esp_config {

struct esp_struct {
int magic;
+ struct tty_port port;
spinlock_t lock;
- int port;
+ int io_port;
int irq;
- int flags; /* defined in tty.h */
- struct tty_struct *tty;
int read_status_mask;
int ignore_status_mask;
int timeout;
@@ -93,14 +92,10 @@ struct esp_struct {
int MCR; /* Modem control register */
unsigned long last_active;
int line;
- int count; /* # of fd on device */
- int blocked_open; /* # of blocked opens */
unsigned char *xmit_buf;
int xmit_head;
int xmit_tail;
int xmit_cnt;
- wait_queue_head_t open_wait;
- wait_queue_head_t close_wait;
wait_queue_head_t delta_msr_wait;
wait_queue_head_t break_wait;
struct async_icount icount; /* kernel counters for the 4 input interrupts */

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/