Re: [linux-dvb] bug: saa7134_init run before v4l2_i2c_drv_init
From: hermann pitton
Date: Sat Jul 12 2008 - 23:26:13 EST
Hi,
the analysis is quite well.
Please propose a fix too ;)
Cheers,
Hermann
Am Samstag, den 12.07.2008, 19:08 +0100 schrieb Simon Arlott:
> (Hardware: SAA7134, TDA9887, MT2050, MT352)
>
> tuner-core.c:tuner_probe doesn't auto-detect the MT20xx tuner
> saa7134-cards.c:saa7134_board_init2 sets the tuner type for any unknown tuner
>
> Normally when saa7134_init runs it calls for the tuner module before calling
> saa7134_board_init2, but if compiled in it will silently fail to set the tuner
> type because it is run before tuner_probe is called.
>
> This used to work ok in 2.6.24, but doesn't in 2.6.26-rc9. I think
> c117d05cd4c09342f97ba1c6ef63f0bae3239a39 looks like it could have caused this,
> but I haven't tried reverting it.
>
> I've tried to use subsys_init for v4l2_i2c_drv_init in include/media/v4l2-i2c-drv.h,
> but it seems to have no effect and it's still loaded after saa7134.
>
> If I rmmod tuner and modprobe it then it fails to work because saa7134_board_init2
> isn't there to set the tuner type - ideally the type should be stored during the
> init of saa7134 in such a way that tuner can refer to it when probing for devices
> (and saa7134 should still prod tuner for the situation where it's loaded later).
>
>
> Kernel log with both compiled in:
> (I've inserted a WARN_ON at the point where saa7134 is about to call
> saa7134_i2c_call_clients.)
> [ 1.716916] calling videodev_init+0x0/0x7d
> [ 1.717030] Linux video capture interface: v2.00
> [ 1.717091] initcall videodev_init+0x0/0x7d returned 0 after 0 msecs
>
> [ 1.717091] calling ir_init+0x0/0x14
> [ 1.717972] initcall ir_init+0x0/0x14 returned 0 after 0 msecs
>
> [ 1.718095] calling saa7134_init+0x0/0x4a
> [ 1.718095] saa7130/34: v4l2 driver version 0.2.14 loaded
> [ 1.718095] ACPI: PCI Interrupt 0000:05:00.0[A] -> Link [LNED] -> GSI 19 (level, low) -> IRQ 19
> [ 1.718095] saa7134[0]: found at 0000:05:00.0, rev: 1, irq: 19, latency: 64, mmio: 0xfeaffc00
> [ 1.718095] saa7134[0]: subsystem: 11bd:002d, board: Pinnacle PCTV 300i DVB-T + PAL [card=50,autodetected]
> [ 1.718104] saa7134[0]: board init: gpio is c806000
> [ 1.859741] saa7134[0]: i2c eeprom 00: bd 11 2d 00 f8 f8 1c 00 43 43 a9 1c 55 d2 b2 92
> [ 1.860128] saa7134[0]: i2c eeprom 10: 00 f0 04 04 ff 20 ff ff ff ff ff ff ff ff ff ff
> [ 1.860338] saa7134[0]: i2c eeprom 20: 01 40 01 02 03 ff 03 01 08 ff 00 25 ff ff ff ff
> [ 1.860725] saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> [ 1.861108] saa7134[0]: i2c eeprom 40: ff 16 00 c0 86 3c 01 01 ff ff ff ff ff ff ff ff
> [ 1.861374] saa7134[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> [ 1.861793] saa7134[0]: i2c eeprom 60: 0c 22 17 44 03 11 e1 a1 ff ff ff ff ff ff ff ff
> [ 1.862177] saa7134[0]: i2c eeprom 70: 00 30 8d 18 3b 02 ff ff 74 50 ff ff ff ff ff ff
> [ 1.862851] saa7134[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> [ 1.863234] saa7134[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> [ 1.863608] saa7134[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> [ 1.864015] saa7134[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> [ 1.864389] saa7134[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> [ 1.864849] saa7134[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> [ 1.865222] saa7134[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> [ 1.865606] saa7134[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> [ 1.866770] ------------[ cut here ]------------
> [ 1.866770] WARNING: at drivers/media/video/saa7134/saa7134-cards.c:5659 saa7134_tuner_setup+0xc3/0x17a()
> [ 1.871794] Modules linked in:
> [ 1.871930] Pid: 1, comm: swapper Not tainted 2.6.26-rc9 #89
> [ 1.872035]
> [ 1.872036] Call Trace:
> [ 1.872238] [<ffffffff80230ffc>] warn_on_slowpath+0x58/0x86
> [ 1.872348] [<ffffffff8023fde3>] ? call_usermodehelper_exec+0xb2/0xc2
> [ 1.872461] [<ffffffff80240139>] ? request_module+0x14b/0x162
> [ 1.872802] [<ffffffff80231b50>] ? printk+0x67/0x69
> [ 1.872802] [<ffffffff803e0747>] saa7134_tuner_setup+0xc3/0x17a
> [ 1.872802] [<ffffffff803e0e61>] ? saa7134_tuner_callback+0x0/0x182
> [ 1.872802] [<ffffffff803e0e54>] saa7134_board_init2+0x656/0x663
> [ 1.872802] [<ffffffff80499ef7>] ? i2c_master_recv+0x3c/0x4b
> [ 1.872802] [<ffffffff803e291c>] ? saa7134_i2c_register+0x144/0x1bd
> [ 1.872806] [<ffffffff805b7879>] saa7134_initdev+0x594/0x8ad
> [ 1.873037] [<ffffffff8034b6f2>] pci_device_probe+0xb3/0x10c
> [ 1.873147] [<ffffffff803b7054>] driver_probe_device+0xd9/0x169
> [ 1.873893] [<ffffffff803b7133>] __driver_attach+0x4f/0x79
> [ 1.873893] [<ffffffff803b70e4>] ? __driver_attach+0x0/0x79
> [ 1.873893] [<ffffffff803b66c6>] bus_for_each_dev+0x4a/0x7b
> [ 1.873893] [<ffffffff803b6e85>] driver_attach+0x1c/0x1e
> [ 1.873893] [<ffffffff803b6b3c>] bus_add_driver+0xb7/0x20b
> [ 1.873893] [<ffffffff803b730f>] driver_register+0x93/0x10a
> [ 1.873896] [<ffffffff8034b975>] __pci_register_driver+0x50/0x8b
> [ 1.874037] [<ffffffff803e1e96>] ? saa7134_init+0x0/0x4a
> [ 1.874133] [<ffffffff803e1ede>] saa7134_init+0x48/0x4a
> [ 1.874910] [<ffffffff807c1940>] kernel_init+0x147/0x29d
> [ 1.874910] [<ffffffff8020c118>] child_rip+0xa/0x12
> [ 1.874910] [<ffffffff807c17f9>] ? kernel_init+0x0/0x29d
> [ 1.874910] [<ffffffff8020c10e>] ? child_rip+0x0/0x12
> [ 1.874910]
> [ 1.874910] ---[ end trace d510dd024e67e971 ]---
> [ 1.876873] saa7134[0]: registered device video0 [v4l2]
> [ 1.876873] saa7134[0]: registered device vbi0
> [ 1.876873] initcall saa7134_init+0x0/0x4a returned 0 after 149 msecs
>
> [ 1.876873] calling empress_register+0x0/0x12
> [ 1.876873] initcall empress_register+0x0/0x12 returned 0 after 0 msecs
>
> [ 1.876873] calling saa6752hs_init_module+0x0/0x14
> [ 1.876873] initcall saa6752hs_init_module+0x0/0x14 returned 0 after 0 msecs
>
> [ 1.876873] calling dvb_register+0x0/0x12
> [ 1.888880] DVB: registering new adapter (saa7134[0])
> [ 1.888991] DVB: registering frontend 0 (Zarlink MT352 DVB-T)...
> [ 1.927841] initcall dvb_register+0x0/0x12 returned 0 after 39 msecs
>
> [ 1.927961] calling v4l2_i2c_drv_init+0x0/0x104
> [ 1.930083] tda829x_probe: driver disabled by Kconfig
> [ 1.930193] tuner' 0-0043: chip found @ 0x86 (saa7134[0])
> [ 1.933311] tda9887 0-0043: creating new instance
> [ 1.933416] tda9887 0-0043: tda988[5/6/7] found
> [ 1.933521] tuner' 0-0043: type set to tda9887
> [ 1.933523] tuner' 0-0043: tv freq set to 0.00
> [ 1.933526] tuner' 0-0043: TV freq (0.00) out of range (44-958)
> [ 1.936050] tuner' 0-0043: saa7134[0] tuner' I2C addr 0x86 with type 74 used for 0x0e
> [ 1.938047] tea5767_autodetection: not probed - driver disabled by Kconfig
> [ 1.938158] tuner' 0-0060: Setting mode_mask to 0x0e
> [ 1.938159] tuner' 0-0060: chip found @ 0xc0 (saa7134[0])
> [ 1.941516] tuner' 0-0060: tuner 0x60: Tuner type absent
> [ 1.944080] initcall v4l2_i2c_drv_init+0x0/0x104 returned 0 after 14 msecs
>
>
> If saa7134 and tuner are modules then everything works ok:
> (I've inserted a WARN_ON at the point where the tuner type is set, showing that
> it originates from saa7134_board_init2.)
> [ 15.408138] Linux video capture interface: v2.00
> [ 15.505111] saa7130/34: v4l2 driver version 0.2.14 loaded
> [ 15.506990] ACPI: PCI Interrupt 0000:05:00.0[A] -> Link [LNED] -> GSI 19 (level, low) -> IRQ 19
> [ 15.506990] saa7134[0]: found at 0000:05:00.0, rev: 1, irq: 19, latency: 64, mmio: 0xfeaffc00
> [ 15.506990] saa7134[0]: subsystem: 11bd:002d, board: Pinnacle PCTV 300i DVB-T + PAL [card=50,autodetected]
> [ 15.506990] saa7134[0]: board init: gpio is c806000
> [ 15.666434] saa7134[0]: i2c eeprom 00: bd 11 2d 00 f8 f8 1c 00 43 43 a9 1c 55 d2 b2 92
> [ 15.666443] saa7134[0]: i2c eeprom 10: 00 f0 04 04 ff 20 ff ff ff ff ff ff ff ff ff ff
> [ 15.666450] saa7134[0]: i2c eeprom 20: 01 40 01 02 03 ff 03 01 08 ff 00 25 ff ff ff ff
> [ 15.666460] saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> [ 15.666466] saa7134[0]: i2c eeprom 40: ff 16 00 c0 86 3c 01 01 ff ff ff ff ff ff ff ff
> [ 15.666472] saa7134[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> [ 15.666478] saa7134[0]: i2c eeprom 60: 0c 22 17 44 03 11 e1 a1 ff ff ff ff ff ff ff ff
> [ 15.666484] saa7134[0]: i2c eeprom 70: 00 30 8d 18 3b 02 ff ff 74 50 ff ff ff ff ff ff
> [ 15.666491] saa7134[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> [ 15.666497] saa7134[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> [ 15.666506] saa7134[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> [ 15.666512] saa7134[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> [ 15.666522] saa7134[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> [ 15.666528] saa7134[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> [ 15.666538] saa7134[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> [ 15.666544] saa7134[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> [ 15.721796] tda829x_probe: driver disabled by Kconfig
> [ 15.721801] tuner' 2-0043: chip found @ 0x86 (saa7134[0])
> [ 15.721805] tda9887 2-0043: creating new instance
> [ 15.721807] tda9887 2-0043: tda988[5/6/7] found
> [ 15.721809] tuner' 2-0043: type set to tda9887
> [ 15.721811] tuner' 2-0043: tv freq set to 0.00
> [ 15.721813] tuner' 2-0043: TV freq (0.00) out of range (44-958)
> [ 15.723788] tuner' 2-0043: saa7134[0] tuner' I2C addr 0x86 with type 74 used for 0x0e
> [ 15.725786] tea5767_autodetection: not probed - driver disabled by Kconfig
> [ 15.725788] tuner' 2-0060: Setting mode_mask to 0x0e
> [ 15.725790] tuner' 2-0060: chip found @ 0xc0 (saa7134[0])
> [ 15.725792] tuner' 2-0060: tuner 0x60: Tuner type absent
> [ 15.728089] ------------[ cut here ]------------
> [ 15.728089] WARNING: at drivers/media/video/tuner-core.c:769 tuner_command+0x10c/0x1063 [tuner]()
> [ 15.728089] Modules linked in: tuner tda9887 mt20xx saa7134(+) compat_ioctl32 videodev v4l1_compat v4l2_common videobuf_dma_sg videobuf_core ir_kbd_i2c ir_common fglrx(P) tveeprom
> [ 15.728089] Pid: 1869, comm: modprobe Tainted: P 2.6.26-rc9 #86
> [ 15.728089]
> [ 15.728089] Call Trace:
> [ 15.728089] [<ffffffff8022fdb9>] warn_on_slowpath+0x51/0x79
> [ 15.728089] [<ffffffff8057ac1c>] schedule_timeout+0x1e/0xad
> [ 15.728089] [<ffffffff8024173e>] autoremove_wake_function+0x9/0x2e
> [ 15.728089] [<ffffffff80226666>] __wake_up_common+0x41/0x74
> [ 15.728089] [<ffffffff80226d62>] __wake_up+0x38/0x4f
> [ 15.728089] [<ffffffffa023c465>] :tuner:tuner_command+0x10c/0x1063
> [ 15.728089] [<ffffffff8023e093>] call_usermodehelper_exec+0xac/0xba
> [ 15.728089] [<ffffffff8045c836>] i2c_cmd+0x0/0x3e
> [ 15.728089] [<ffffffff8045c86d>] i2c_cmd+0x37/0x3e
> [ 15.728089] [<ffffffff803a4d71>] device_for_each_child+0x22/0x4d
> [ 15.728089] [<ffffffff80230851>] printk+0x4e/0x56
> [ 15.728089] [<ffffffff8045b101>] i2c_clients_command+0x1f/0x24
> [ 15.728089] [<ffffffffa020d0ca>] :saa7134:saa7134_tuner_setup+0xca/0x175
> [ 15.728089] [<ffffffffa020d7ff>] :saa7134:saa7134_tuner_callback+0x0/0x178
> [ 15.728089] [<ffffffffa020d7f4>] :saa7134:saa7134_board_init2+0x67f/0x68a
> [ 15.728089] [<ffffffff8045baf3>] i2c_master_recv+0x3a/0x46
> [ 15.728089] [<ffffffffa020f216>] :saa7134:saa7134_i2c_register+0x135/0x1ad
> [ 15.728089] [<ffffffff8057ac83>] schedule_timeout+0x85/0xad
> [ 15.728089] [<ffffffffa02161d7>] :saa7134:saa7134_initdev+0x59d/0x8dc
> [ 15.728089] [<ffffffff8033fdc4>] pci_device_probe+0xa9/0xf8
> [ 15.728089] [<ffffffff803a71c3>] driver_probe_device+0xd7/0x164
> [ 15.728089] [<ffffffff803a7296>] __driver_attach+0x46/0x6d
> [ 15.728089] [<ffffffff803a7250>] __driver_attach+0x0/0x6d
> [ 15.728089] [<ffffffff803a68ab>] bus_for_each_dev+0x44/0x6f
> [ 15.728089] [<ffffffffa01ed458>] :videobuf_core:videobuf_mmap_free+0x0/0x2b
> [ 15.728089] [<ffffffff803a6ce1>] bus_add_driver+0xb4/0x203
> [ 15.728089] [<ffffffff803a7447>] driver_register+0x8d/0x101
> [ 15.728089] [<ffffffff80340025>] __pci_register_driver+0x47/0x7a
> [ 15.728089] [<ffffffff80250208>] sys_init_module+0x9b/0x1a9
> [ 15.728089] [<ffffffff8020b14b>] system_call_after_swapgs+0x7b/0x80
> [ 15.728089]
> [ 15.728089] ---[ end trace dbce26c647b7fcc0 ]---
> [ 15.728089] tuner' 2-0043: Calling set_type_addr for type=33, addr=0xff, mode=0x0e, config=0x00
> [ 15.728089] tuner' 2-0043: set addr discarded for type 74, mask e. Asked to change tuner at addr 0xff, with mask e
> [ 15.728089] ------------[ cut here ]------------
> [ 15.728089] WARNING: at drivers/media/video/tuner-core.c:769 tuner_command+0x10c/0x1063 [tuner]()
> [ 15.728089] Modules linked in: tuner tda9887 mt20xx saa7134(+) compat_ioctl32 videodev v4l1_compat v4l2_common videobuf_dma_sg videobuf_core ir_kbd_i2c ir_common fglrx(P) tveeprom
> [ 15.728089] Pid: 1869, comm: modprobe Tainted: P W 2.6.26-rc9 #86
> [ 15.728089]
> [ 15.728089] Call Trace:
> [ 15.728089] [<ffffffff8022fdb9>] warn_on_slowpath+0x51/0x79
> [ 15.728089] [<ffffffff80230851>] printk+0x4e/0x56
> [ 15.728089] [<ffffffff8057ac1c>] schedule_timeout+0x1e/0xad
> [ 15.728089] [<ffffffff80226d62>] __wake_up+0x38/0x4f
> [ 15.728089] [<ffffffffa023c465>] :tuner:tuner_command+0x10c/0x1063
> [ 15.728089] [<ffffffff8045c836>] i2c_cmd+0x0/0x3e
> [ 15.728089] [<ffffffff8045c86d>] i2c_cmd+0x37/0x3e
> [ 15.728089] [<ffffffff803a4d71>] device_for_each_child+0x22/0x4d
> [ 15.728089] [<ffffffff80230851>] printk+0x4e/0x56
> [ 15.728089] [<ffffffff8045b101>] i2c_clients_command+0x1f/0x24
> [ 15.728089] [<ffffffffa020d0ca>] :saa7134:saa7134_tuner_setup+0xca/0x175
> [ 15.728089] [<ffffffffa020d7ff>] :saa7134:saa7134_tuner_callback+0x0/0x178
> [ 15.728089] [<ffffffffa020d7f4>] :saa7134:saa7134_board_init2+0x67f/0x68a
> [ 15.728089] [<ffffffff8045baf3>] i2c_master_recv+0x3a/0x46
> [ 15.728089] [<ffffffffa020f216>] :saa7134:saa7134_i2c_register+0x135/0x1ad
> [ 15.728089] [<ffffffff8057ac83>] schedule_timeout+0x85/0xad
> [ 15.728089] [<ffffffffa02161d7>] :saa7134:saa7134_initdev+0x59d/0x8dc
> [ 15.728089] [<ffffffff8033fdc4>] pci_device_probe+0xa9/0xf8
> [ 15.728089] [<ffffffff803a71c3>] driver_probe_device+0xd7/0x164
> [ 15.728089] [<ffffffff803a7296>] __driver_attach+0x46/0x6d
> [ 15.728089] [<ffffffff803a7250>] __driver_attach+0x0/0x6d
> [ 15.728089] [<ffffffff803a68ab>] bus_for_each_dev+0x44/0x6f
> [ 15.728089] [<ffffffffa01ed458>] :videobuf_core:videobuf_mmap_free+0x0/0x2b
> [ 15.728089] [<ffffffff803a6ce1>] bus_add_driver+0xb4/0x203
> [ 15.728089] [<ffffffff803a7447>] driver_register+0x8d/0x101
> [ 15.728089] [<ffffffff80340025>] __pci_register_driver+0x47/0x7a
> [ 15.728089] [<ffffffff80250208>] sys_init_module+0x9b/0x1a9
> [ 15.728089] [<ffffffff8020b14b>] system_call_after_swapgs+0x7b/0x80
> [ 15.728089]
> [ 15.728089] ---[ end trace dbce26c647b7fcc0 ]---
> [ 15.728089] tuner' 2-0060: Calling set_type_addr for type=33, addr=0xff, mode=0x0e, config=0x00
> [ 15.728089] tuner' 2-0060: defining GPIO callback
> [ 15.739273] mt20xx 2-0060: microtune: companycode=3cbf part=42 rev=22
> [ 15.747800] mt20xx 2-0060: microtune MT2050 found, OK
> [ 15.747803] tuner' 2-0060: type set to MT2050
> [ 15.747806] tuner' 2-0060: tv freq set to 400.00
> [ 15.752795] tuner' 2-0060: saa7134[0] tuner' I2C addr 0xc0 with type 33 used for 0x0e
> [ 15.754532] tuner' 2-0043: switching to v4l2
> [ 15.754534] tuner' 2-0060: switching to v4l2
> [ 15.754536] tuner' 2-0060: tv freq set to 400.00
> [ 15.759525] tuner' 2-0060: tv freq set to 400.00
> [ 15.765272] saa7134[0]: registered device video0 [v4l2]
> [ 15.765272] saa7134[0]: registered device vbi0
> [ 15.765272] tuner' 2-0043: Cmd TUNER_SET_STANDBY accepted for analog TV
> [ 15.768097] tuner' 2-0060: Cmd TUNER_SET_STANDBY accepted for analog TV
> [ 15.836381] DVB: registering new adapter (saa7134[0])
> [ 15.836386] DVB: registering frontend 0 (Zarlink MT352 DVB-T)...
>
> If I have tuner already loaded, tuner_probe is run while initialising saa7134:
> [ 233.930597] saa7130/34: v4l2 driver version 0.2.14 loaded
> [ 233.931449] saa7134[0]: found at 0000:05:00.0, rev: 1, irq: 19, latency: 64, mmio: 0xfeaffc00
> [ 233.931651] saa7134[0]: subsystem: 11bd:002d, board: Pinnacle PCTV 300i DVB-T + PAL [card=50,autodetected]
> [ 233.931674] saa7134[0]: board init: gpio is c80e000
> [ 234.056662] tda829x_probe: driver disabled by Kconfig
> [ 234.056794] tuner' 2-0043: chip found @ 0x86 (saa7134[0])
> [ 234.056906] tda9887 2-0043: creating new instance
> [ 234.056911] tda9887 2-0043: tda988[5/6/7] found
> [ 234.056914] tuner' 2-0043: type set to tda9887
> [ 234.056918] tuner' 2-0043: tv freq set to 0.00
> [ 234.056922] tuner' 2-0043: TV freq (0.00) out of range (44-958)
> [ 234.060656] tuner' 2-0043: saa7134[0] tuner' I2C addr 0x86 with type 74 used for 0x0e
> [ 234.062634] tea5767_autodetection: not probed - driver disabled by Kconfig
> [ 234.062762] tuner' 2-0060: Setting mode_mask to 0x0e
> [ 234.062866] tuner' 2-0060: chip found @ 0xc0 (saa7134[0])
> [ 234.063006] tuner' 2-0060: tuner 0x60: Tuner type absent
> [ 234.104185] saa7134[0]: i2c eeprom 00: bd 11 2d 00 f8 f8 1c 00 43 43 a9 1c 55 d2 b2 92
> [ 234.104654] saa7134[0]: i2c eeprom 10: 00 f0 04 04 ff 20 ff ff ff ff ff ff ff ff ff ff
> [ 234.104661] saa7134[0]: i2c eeprom 20: 01 40 01 02 03 ff 03 01 08 ff 00 25 ff ff ff ff
> [ 234.104665] saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> [ 234.104669] saa7134[0]: i2c eeprom 40: ff 16 00 c0 86 3c 01 01 ff ff ff ff ff ff ff ff
> [ 234.104673] saa7134[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> [ 234.104678] saa7134[0]: i2c eeprom 60: 0c 22 17 44 03 11 e1 a1 ff ff ff ff ff ff ff ff
> [ 234.104682] saa7134[0]: i2c eeprom 70: 00 30 8d 18 3b 02 ff ff 74 50 ff ff ff ff ff ff
> [ 234.104686] saa7134[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> [ 234.104690] saa7134[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> [ 234.104694] saa7134[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> [ 234.104698] saa7134[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> [ 234.104702] saa7134[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> [ 234.104706] saa7134[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> [ 234.104711] saa7134[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> [ 234.104715] saa7134[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/