Re: [PATCH 2.6.26] PCI: refuse to re-add a device to a bus upon pci_scan_child_bus()

[Eran Liberty]

WOW, sorry for the html tags (though I had this Thunderbird under 
control). Here is the same mail without html tags (hopeully)


Matthew,
You seem to have a finer grasp of the subject then I do, please 
correct/educate me on any of the points I raise in the following lines.

Matthew Wilcox wrote:

> On Tue, Jul 22, 2008 at 11:21:06AM +0300, eran liberty wrote:
> > > I think this is your real problem, that you're rescanning the entire
> > > bus.  I don't think that's the route we'd recommend taking.
> > My stating point was that I have loaded a new design into a
> > programmable device which sits on the pci device. The new design can
> > implement numerous pci devices or non at all. I can think of an easy
> > way (or clean one) to scan only the programmable device. Scanning the
> > whole bus seemed reasonable.
> That's what pci_scan_slot() is for.  It scans the first function at the
> device number, then (if the header indicates it's a multifunction
> device) scans the other functions associated with that device.  eg you
> could call pci_scan_slot(bus, 0x30) and it will create function 06.0
> (and potentially 06.1, 06.2, ...)
> You presumably already have the devfn for the existing device since
> you're able to call pci_remove_bus_device().
Each slot represent a single device which can have more then one 
function.  pci_scan_slot is aimed for scanning these multiple functions.
I, on the other hand, have programmable device on the pci bus which is, 
for the sake of this discussion, a complete black box.
This black box up on loading can implement more then one device, which 
can have more then one function each.
So as far as I see it, now I need to scan all slots on the bus.

But to be honest, upon looking a way to make my device work I dismissed 
the "pci_scan_slot()" option as It did not reach the "fixup_resource ()" 
part.

> > > Why don't you call pci_scan_slot() instead?  You won't get the benefit of
> > > pcibios_fixup_bus(), but I'm not convinced that's safe to call on a bus
> > > that's already been scanned.
> > >       
> > As said its not exactly a slot its more like a regular pci device that
> > someone suddenly welded into the pci bus. Its not a hotplug as well,
> > and I do not want to give up on the pcibios_fixup_bus()
> >     
>
> Why not?  What architecture are you using?  What does
> pcibios_fixup_bus() do for you?
>   
I work with ARCH=powerpc. pcibios_fixup_bus() will deal with all the 
resource bars allocation.
I needed Linux to renegotiate the resources bars on the PCI devices.

> (as a side-note, I'd like to reimplement the pcibios_fixup_*() routines;
> I think a lot of what they do can be done more generically these days.
> It'll take a while and isn't high on my priority list).
>   
If I can lend a hand there, let me know and I will try to squeeze it in 
somewhere.

>   
> > As it is, with my patch applied i successfully go over the bus and
> > remove my own devices before I reprogram the
> > programmable device.
> >
> > while ((dev = pci_get_device(PCI_VENDOR_ID_MYCOMP,PCI_DEVICE_ID_MYDEV,NULL))
> > != NULL) {
> > 	pci_remove_bus_device(dev);
> > 	pci_dev_put(dev);
> > }
> >
> > Load a new design into it.
> >
> > Then scan the entire bus and add the newly discovered devices.
> >
> > bus = null;
> > while ((bus = pci_find_next_bus(bus)) != NULL) {
> > 	pci_scan_child_bus(bus);
> > 	pci_bus_assign_resources(bus);
> > 	pci_bus_add_devices(bus);
> > }
> >
> > As seen here, this sequence of instructions seems very intuitive. It
> > will fail without the patch upon pci_bus_add_devices().
> >     
>
> Seems utterly unintuitive to me.  You're doing a lot of unnecessary work
> here, and if you have two cards in your machine, you'll take away both
> of them when you reload either of them.
>   
Hmmm, I do want to remove all the devices that are implemented by the 
programmable unit which is reloaded.
I have not considered the possibility of having more then one 
programmable unit.
I guess that the removing part can be more fine tuned as the need arises.

> What you should do is cache the pci_bus and the devfn at startup:
>
> static struct pci_bus *my_bus;
> static int my_devfn;
>
> 	struct pci_dev *dev = pci_get_device(PCI_VENDOR_ID_MYCOMP,
> 					PCI_DEVICE_ID_MYDEV, NULL);
> 	if (!dev)
> 		return -ENODEV;
> 	my_bus = dev->bus;
> 	my_devfn = dev->devfn;
> 	pci_dev_put(dev);
>
> when you want to remove it:
>
> 	for (func = 0; func < 8; func++)
> 		struct pci_dev *dev = pci_get_slot(my_bus, my_devfn + func);
> 		if (!dev)
> 			continue;
> 		pci_remove_bus_device(dev);
> 		pci_dev_put(dev);
> 	}
>
> when you want to rescan it:
>
> 	pci_scan_slot(my_bus, my_devfn);
>
> (this only handles one programmable card.  The basic idea could be
> extended to handle multiple cards if you need to do that).
>   
I think there is a hidden assumption in this code, again please correct 
me if I missed the point.
This code assumes that the devices which will re-appear after the 
programmable unit is loaded has the same devfn and bus as the devices 
which were present before the reload.
This assumption might be wrong.

For example, I have a basic programmable image which has no pci devices 
at all.
upon unloading I do not remove any device (as non are present) and up on 
reloading I suddenly have two. What is their bus? their devfn?

Ultimately I would have expected to find a "int pci_scan_bus(struct 
pci_bus *bus );" the "pci_scan_child_bus ()" was the closest to the mark

Liberty

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/