Re: mpt fusion broken sometime since 2.6.24

From: david
Date: Tue Feb 17 2009 - 18:38:40 EST

Next message: Ingo Molnar: "Re: [PATCH 00/15] [git pull] for tip/tracing/ftrace"
Previous message: Ingo Molnar: "Re: tip: bzip2/lzma now in tip:x86/setup-lzma"
In reply to: Yinghai Lu: "Re: mpt fusion broken sometime since 2.6.24"
Next in thread: Yinghai Lu: "Re: mpt fusion broken sometime since 2.6.24"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On Tue, 17 Feb 2009, Yinghai Lu wrote:

david@xxxxxxx wrote:
On Tue, 17 Feb 2009, Yinghai Lu wrote:

Subject: Re: mpt fusion broken sometime since 2.6.24

On Tue, Feb 17, 2009 at 3:07 PM, <david@xxxxxxx> wrote:
On Tue, 17 Feb 2009, Matthew Wilcox wrote:

On Tue, Feb 17, 2009 at 01:44:55PM -0800, david@xxxxxxx wrote:

I got a picture of the failed boot at
http://linux.lang.hm/linux/IMG00052.jpg

The PCI-MSI line is probably indicative. Can you try booting with:

mptbase.mpt_msi_enable_sas=0

and also send us an lspci -v so we can update the blacklist?

is that disabling SAS for this system? if so, that's the wrong thing
to do
(the drives are SAS)

it only disable MSI with that mptsas.
and mptsas will use ioapic routing.

can you post whole bootlog?

unfortunantly it's booting from CD and the only drives in the system are
the ones that are not being accessed.

i mean with kernel before 2.6.24..

Ok, attached.

David Lang00:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a3)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [44] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=0 UnitCnt=15 MastHost- DefDir- DUL-
Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=1 IsocEn- LSEn- ExtCTL- 64b-
Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 1.03
Link Frequency 0: 1.0GHz
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
Link Frequency 1: 200MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [e0] HyperTransport: MSI Mapping

00:01.0 ISA bridge: nVidia Corporation CK804 ISA Bridge (rev a3)
Subsystem: nVidia Corporation Unknown device cb84
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0

00:01.1 SMBus: nVidia Corporation CK804 SMBus (rev a2)
Subsystem: nVidia Corporation Unknown device cb84
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at a400 [size=32]
Region 4: I/O ports at 2300 [size=64]
Region 5: I/O ports at 2340 [size=64]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:02.0 USB Controller: nVidia Corporation CK804 USB Controller (rev a2) (prog-if 10 [OHCI])
Subsystem: nVidia Corporation Unknown device cb84
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fe1fc000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:02.1 USB Controller: nVidia Corporation CK804 USB Controller (rev a3) (prog-if 20 [EHCI])
Subsystem: nVidia Corporation Unknown device cb84
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 21
Region 0: Memory at fe1fdc00 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Debug port
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:06.0 IDE interface: nVidia Corporation CK804 IDE (rev a2) (prog-if 8a [Master SecP PriP])
Subsystem: nVidia Corporation Unknown device cb84
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
Region 4: I/O ports at 0d00 [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev a3) (prog-if 85 [Master SecO PriO])
Subsystem: nVidia Corporation Unknown device cb84
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at b800 [size=8]
Region 1: I/O ports at b400 [size=4]
Region 2: I/O ports at b000 [size=8]
Region 3: I/O ports at ac00 [size=4]
Region 4: I/O ports at a800 [size=16]
Region 5: Memory at fe1fe000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:08.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev a3) (prog-if 85 [Master SecO PriO])
Subsystem: nVidia Corporation Unknown device cb84
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at cc00 [size=8]
Region 1: I/O ports at c800 [size=4]
Region 2: I/O ports at c400 [size=8]
Region 3: I/O ports at c000 [size=4]
Region 4: I/O ports at bc00 [size=16]
Region 5: Memory at fe1ff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:09.0 PCI bridge: nVidia Corporation CK804 PCI Bridge (rev a2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=128
I/O behind bridge: 00009000-00009fff
Memory behind bridge: fd800000-fe0fffff
Prefetchable memory behind bridge: fb400000-fd3fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-

00:0b.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
Address: 00000000feeff00c Data: 4149
Capabilities: [58] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <4us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x2, ASPM L0s, Port 3
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 8, PowerLimit 25.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-

00:0c.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Memory behind bridge: fd700000-fd7fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
Address: 00000000feeff00c Data: 4151
Capabilities: [58] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <4us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 2
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 4, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-

00:0d.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Memory behind bridge: fd600000-fd6fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
Address: 00000000feeff00c Data: 4159
Capabilities: [58] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <4us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 1
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 2, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-

00:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
Address: 00000000feeff00c Data: 4161
Capabilities: [58] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <4us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s, Port 0
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 1, PowerLimit 75.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-

00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
Capabilities: [a0] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
Capabilities: [c0] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02

00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [f0] #0f [0010]

00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
Capabilities: [a0] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
Capabilities: [c0] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02

00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [f0] #0f [0010]

00:1a.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
Capabilities: [a0] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=N/C LWO=N/C
Revision ID: 1.02
Capabilities: [c0] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02

00:1a.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:1a.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:1a.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [f0] #0f [0010]

00:1b.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
Capabilities: [a0] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
Capabilities: [c0] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=N/C LWO=N/C
Revision ID: 1.02

00:1b.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:1b.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:1b.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [f0] #0f [0010]

02:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express (rev 11)
Subsystem: Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fd6f0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3 Enable-
Address: df59a117da2b636c Data: 0309
Capabilities: [d0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <4us, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 0
Link: Latency L0s <2us, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1

03:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express (rev 11)
Subsystem: Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at fd7f0000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3 Enable-
Address: f30140001e000ea4 Data: 1b2c
Capabilities: [d0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <4us, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 0
Link: Latency L0s <2us, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1

05:06.0 VGA compatible controller: XGI - Xabre Graphics Inc Volari Z7 (prog-if 00 [VGA])
Subsystem: XGI - Xabre Graphics Inc Volari Z7
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
BIST result: 00
Region 0: Memory at fc000000 (32-bit, prefetchable) [size=16M]
Region 1: Memory at fdc00000 (32-bit, non-prefetchable) [size=256K]
Region 2: I/O ports at 9000 [size=128]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

05:07.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
Subsystem: Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fe0ff800 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at fe0f8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+

80:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a3)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [44] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=0 UnitCnt=15 MastHost- DefDir- DUL-
Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=3 IsocEn- LSEn- ExtCTL- 64b-
Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 1.03
Link Frequency 0: 1.0GHz
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
Link Frequency 1: 200MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [e0] HyperTransport: MSI Mapping

80:01.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a3)
Subsystem: nVidia Corporation Unknown device cb84
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 1: Memory at febfc000 (32-bit, non-prefetchable) [size=4K]

80:08.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev a3) (prog-if 85 [Master SecO PriO])
Subsystem: nVidia Corporation Unknown device cb84
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 47
Region 0: I/O ports at fc00 [size=8]
Region 1: I/O ports at f800 [size=4]
Region 2: I/O ports at f400 [size=8]
Region 3: I/O ports at f000 [size=4]
Region 4: I/O ports at ec00 [size=16]
Region 5: Memory at febfd000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

80:0d.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=80, secondary=84, subordinate=84, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
Address: 00000000feeff00c Data: 4169
Capabilities: [58] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <4us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 1
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 2, PowerLimit 25.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-

80:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=80, secondary=83, subordinate=83, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
Address: 00000000feeff00c Data: 4171
Capabilities: [58] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 <4us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s, Port 0
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 1, PowerLimit 75.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-

80:10.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8132 PCI-X Bridge (rev 11) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Bus: primary=80, secondary=82, subordinate=82, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fe200000-feafffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [60] PCI-X bridge device
Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=100MHz
Status: Dev=80:10.0 64bit+ 133MHz+ SCD- USC- SCO- SRD-
Upstream: Capacity=13 CommitmentLimit=65535
Downstream: Capacity=2 CommitmentLimit=65535
Capabilities: [b8] HyperTransport: Interrupt Discovery and Configuration
Capabilities: [c0] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=16 UnitCnt=2 MastHost- DefDir- DUL-
Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
Link Control 1: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 1: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
Revision ID: 2.00
Link Frequency 0: 1.0GHz
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz- 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC- LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD-
Link Frequency 1: 1.0GHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz+ 300MHz- 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Error Handling: PFlE- OFlE- PFE+ OFE+ EOCFE+ RFE- CRCFE+ SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [f4] HyperTransport: MSI Mapping

80:10.1 PIC: Advanced Micro Devices [AMD] AMD-8132 PCI-X IOAPIC (rev 11) (prog-if 10 [IO-APIC])
Subsystem: Advanced Micro Devices [AMD] AMD-8132 PCI-X IOAPIC
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at febfe000 (64-bit, non-prefetchable) [size=4K]

80:11.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8132 PCI-X Bridge (rev 11) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Bus: primary=80, secondary=81, subordinate=81, sec-latency=64
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [60] PCI-X bridge device
Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz
Status: Dev=80:11.0 64bit+ 133MHz+ SCD- USC- SCO- SRD-
Upstream: Capacity=13 CommitmentLimit=65535
Downstream: Capacity=2 CommitmentLimit=65535
Capabilities: [b8] HyperTransport: Interrupt Discovery and Configuration
Capabilities: [c0] HyperTransport: Revision ID: 2.00
Capabilities: [f4] HyperTransport: MSI Mapping

80:11.1 PIC: Advanced Micro Devices [AMD] AMD-8132 PCI-X IOAPIC (rev 11) (prog-if 10 [IO-APIC])
Subsystem: Advanced Micro Devices [AMD] AMD-8132 PCI-X IOAPIC
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at febff000 (64-bit, non-prefetchable) [size=4K]

82:03.0 SCSI storage controller: LSI Logic / Symbios Logic SAS1068 PCI-X Fusion-MPT SAS (rev 02)
Subsystem: LSI Logic / Symbios Logic Unknown device 1000
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 72 (16000ns min, 2500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 75
Region 0: I/O ports at d800 [disabled] [size=256]
Region 1: Memory at feafc000 (64-bit, non-prefetchable) [size=16K]
Region 3: Memory at feae0000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at fe400000 [disabled] [size=4M]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [98] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [68] PCI-X non-bridge device
Command: DPERE- ERO- RBC=512 OST=16
Status: Dev=82:03.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=16 DMCRS=128 RSCEM- 266MHz- 533MHz-
Capabilities: [b0] MSI-X: Enable- Mask- TabSize=1
Vector table: BAR=1 offset=00002000
PBA: BAR=1 offset=00003000

Initializing cgroup subsys cpuset
Linux version 2.6.24-etchnhalf.1-amd64 (Debian 2.6.24-6~etchnhalf.4) (dannf@xxxxxxxxxx) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Mon Jul 21 10:36:02 UTC 2008
Command line: auto BOOT_IMAGE=Linux ro root=802
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 0000000000093800 (usable)
BIOS-e820: 0000000000093800 - 0000000000094c00 (reserved)
BIOS-e820: 00000000000eadc0 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000dfff0000 (usable)
BIOS-e820: 00000000dfff0000 - 00000000dfffe000 (ACPI data)
BIOS-e820: 00000000dfffe000 - 00000000e0000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff700000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000820000000 (usable)
Entering add_active_range(0, 0, 147) 0 entries of 3200 used
Entering add_active_range(0, 256, 917488) 1 entries of 3200 used
Entering add_active_range(0, 1048576, 8519680) 2 entries of 3200 used
end_pfn_map = 8519680
DMI present.
ACPI: RSDP 000F9440, 0014 (r0 ACPIAM)
ACPI: RSDT DFFF0000, 0034 (r1 A M I OEMRSDT 6000714 MSFT 97)
ACPI: FACP DFFF0200, 0084 (r2 A M I OEMFACP 6000714 MSFT 97)
ACPI: DSDT DFFF0440, 5218 (r1 WTF4V WTF4V034 34 INTL 2002026)
ACPI: FACS DFFFE000, 0040
ACPI: APIC DFFF0390, 00B0 (r1 A M I OEMAPIC 6000714 MSFT 97)
ACPI: OEMB DFFFE040, 0063 (r1 A M I AMI_OEM 6000714 MSFT 97)
ACPI: SRAT DFFF5660, 01A0 (r1 AMD HAMMER 1 AMD 1)
SRAT: PXM 0 -> APIC 0 -> Node 0
SRAT: PXM 0 -> APIC 1 -> Node 0
SRAT: PXM 1 -> APIC 2 -> Node 1
SRAT: PXM 1 -> APIC 3 -> Node 1
SRAT: PXM 2 -> APIC 4 -> Node 2
SRAT: PXM 2 -> APIC 5 -> Node 2
SRAT: PXM 3 -> APIC 6 -> Node 3
SRAT: PXM 3 -> APIC 7 -> Node 3
SRAT: Node 0 PXM 0 0-a0000
Entering add_active_range(0, 0, 147) 0 entries of 3200 used
SRAT: Node 0 PXM 0 0-e0000000
Entering add_active_range(0, 0, 147) 1 entries of 3200 used
Entering add_active_range(0, 256, 917488) 1 entries of 3200 used
SRAT: Node 0 PXM 0 0-220000000
Entering add_active_range(0, 0, 147) 2 entries of 3200 used
Entering add_active_range(0, 256, 917488) 2 entries of 3200 used
Entering add_active_range(0, 1048576, 2228224) 2 entries of 3200 used
SRAT: Node 1 PXM 1 220000000-420000000
Entering add_active_range(1, 2228224, 4325376) 3 entries of 3200 used
SRAT: Node 2 PXM 2 420000000-620000000
Entering add_active_range(2, 4325376, 6422528) 4 entries of 3200 used
SRAT: Node 3 PXM 3 620000000-820000000
Entering add_active_range(3, 6422528, 8519680) 5 entries of 3200 used
NUMA: Allocated memnodemap from 2a000 - 2a0c1
NUMA: Using 29 for the hash shift.
Bootmem setup node 0 0000000000000000-0000000220000000
Bootmem setup node 1 0000000220000000-0000000420000000
Bootmem setup node 2 0000000420000000-0000000620000000
Bootmem setup node 3 0000000620000000-0000000820000000
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 8519680
Movable zone start PFN for each node
early_node_map[6] active PFN ranges
0: 0 -> 147
0: 256 -> 917488
0: 1048576 -> 2228224
1: 2228224 -> 4325376
2: 4325376 -> 6422528
3: 6422528 -> 8519680
On node 0 totalpages: 2097027
DMA zone: 56 pages used for memmap
DMA zone: 2460 pages reserved
DMA zone: 1471 pages, LIFO batch:0
DMA32 zone: 14280 pages used for memmap
DMA32 zone: 899112 pages, LIFO batch:31
Normal zone: 16128 pages used for memmap
Normal zone: 1163520 pages, LIFO batch:31
Movable zone: 0 pages used for memmap
On node 1 totalpages: 2097152
DMA zone: 0 pages used for memmap
DMA32 zone: 0 pages used for memmap
Normal zone: 28672 pages used for memmap
Normal zone: 2068480 pages, LIFO batch:31
Movable zone: 0 pages used for memmap
On node 2 totalpages: 2097152
DMA zone: 0 pages used for memmap
DMA32 zone: 0 pages used for memmap
Normal zone: 28672 pages used for memmap
Normal zone: 2068480 pages, LIFO batch:31
Movable zone: 0 pages used for memmap
On node 3 totalpages: 2097152
DMA zone: 0 pages used for memmap
DMA32 zone: 0 pages used for memmap
Normal zone: 28672 pages used for memmap
Normal zone: 2068480 pages, LIFO batch:31
Movable zone: 0 pages used for memmap
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
ACPI: PM-Timer IO Port: 0x2008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
Processor #2
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
Processor #3
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] enabled)
Processor #4
ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] enabled)
Processor #5
ACPI: LAPIC (acpi_id[0x07] lapic_id[0x06] enabled)
Processor #6
ACPI: LAPIC (acpi_id[0x08] lapic_id[0x07] enabled)
Processor #7
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x09] address[0xfebfc000] gsi_base[24])
IOAPIC[1]: apic_id 9, address 0xfebfc000, GSI 24-47
ACPI: IOAPIC (id[0x0a] address[0xfebfe000] gsi_base[72])
IOAPIC[2]: apic_id 10, address 0xfebfe000, GSI 72-78
ACPI: IOAPIC (id[0x0b] address[0xfebff000] gsi_base[79])
IOAPIC[3]: apic_id 11, address 0xfebff000, GSI 79-85
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
swsusp: Registered nosave memory region: 0000000000093000 - 0000000000094000
swsusp: Registered nosave memory region: 0000000000094000 - 00000000000eb000
swsusp: Registered nosave memory region: 00000000000eb000 - 0000000000100000
swsusp: Registered nosave memory region: 00000000dfff0000 - 00000000dfffe000
swsusp: Registered nosave memory region: 00000000dfffe000 - 00000000e0000000
swsusp: Registered nosave memory region: 00000000e0000000 - 00000000fec00000
swsusp: Registered nosave memory region: 00000000fec00000 - 00000000fec01000
swsusp: Registered nosave memory region: 00000000fec01000 - 00000000fee00000
swsusp: Registered nosave memory region: 00000000fee00000 - 00000000fee01000
swsusp: Registered nosave memory region: 00000000fee01000 - 00000000ff700000
swsusp: Registered nosave memory region: 00000000ff700000 - 0000000100000000
Allocating PCI resources starting at e2000000 (gap: e0000000:1ec00000)
SMP: Allowing 8 CPUs, 0 hotplug CPUs
PERCPU: Allocating 34400 bytes of per cpu data
Built 4 zonelists in Zone order, mobility grouping on. Total pages: 8269543
Policy zone: Normal
Kernel command line: auto BOOT_IMAGE=Linux ro root=802
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
TSC calibrated against PM_TIMER
Marking TSC unstable due to TSCs unsynchronized
time.c: Detected 2814.427 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Checking aperture...
CPU 0: aperture @ f4000000 size 64 MB
CPU 1: aperture @ f4000000 size 64 MB
CPU 2: aperture @ f4000000 size 64 MB
CPU 3: aperture @ f4000000 size 64 MB
Memory: 33077220k/34078720k available (2146k kernel code, 476712k reserved, 1004k data, 316k init)
Calibrating delay using timer specific routine.. 5632.28 BogoMIPS (lpj=11264579)
Security Framework initialized
SELinux: Disabled at boot.
Capability LSM initialized
Dentry cache hash table entries: 4194304 (order: 13, 33554432 bytes)
Inode-cache hash table entries: 2097152 (order: 12, 16777216 bytes)
Mount-cache hash table entries: 256
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0/0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Using local APIC timer interrupts.
APIC timer calibration result 12564415
Detected 12.564 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/8 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 5628.88 BogoMIPS (lpj=11257778)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
Dual-Core AMD Opteron(tm) Processor 8220 stepping 03
SMP alternatives: switching to SMP code
Booting processor 2/8 APIC 0x2
Initializing CPU#2
Calibrating delay using timer specific routine.. 5628.92 BogoMIPS (lpj=11257846)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 2/2 -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 0
Dual-Core AMD Opteron(tm) Processor 8220 stepping 03
SMP alternatives: switching to SMP code
Booting processor 3/8 APIC 0x3
Initializing CPU#3
Calibrating delay using timer specific routine.. 5628.91 BogoMIPS (lpj=11257835)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 3/3 -> Node 1
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 1
Dual-Core AMD Opteron(tm) Processor 8220 stepping 03
SMP alternatives: switching to SMP code
Booting processor 4/8 APIC 0x4
Initializing CPU#4
Calibrating delay using timer specific routine.. 5628.91 BogoMIPS (lpj=11257822)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 4/4 -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 0
Dual-Core AMD Opteron(tm) Processor 8220 stepping 03
SMP alternatives: switching to SMP code
Booting processor 5/8 APIC 0x5
Initializing CPU#5
Calibrating delay using timer specific routine.. 5628.90 BogoMIPS (lpj=11257816)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 5/5 -> Node 2
CPU: Physical Processor ID: 2
CPU: Processor Core ID: 1
Dual-Core AMD Opteron(tm) Processor 8220 stepping 03
SMP alternatives: switching to SMP code
Booting processor 6/8 APIC 0x6
Initializing CPU#6
Calibrating delay using timer specific routine.. 5628.91 BogoMIPS (lpj=11257827)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 6/6 -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 0
Dual-Core AMD Opteron(tm) Processor 8220 stepping 03
SMP alternatives: switching to SMP code
Booting processor 7/8 APIC 0x7
Initializing CPU#7
Calibrating delay using timer specific routine.. 5628.91 BogoMIPS (lpj=11257838)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 7/7 -> Node 3
CPU: Physical Processor ID: 3
CPU: Processor Core ID: 1
Dual-Core AMD Opteron(tm) Processor 8220 stepping 03
Brought up 8 CPUs
net_namespace: 120 bytes
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:09.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Root Bridge [PCIB] (0000:80)
ACPI: PCI Interrupt Routing Table [\_SB_.PCIB._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCIB.POGA._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCIB.POGB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *5
ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *5
ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *7
ACPI: PCI Interrupt Link [LNKE] (IRQs 16 17 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22) *9
ACPI: PCI Interrupt Link [LUS1] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22) *11
ACPI: PCI Interrupt Link [LKLN] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LAUI] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LKMO] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LKSM] (IRQs 20 21 22) *5
ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22) *11
ACPI: PCI Interrupt Link [LTIE] (IRQs 20 21 22) *10
ACPI: PCI Interrupt Link [LN2A] (IRQs 40 41 42 43) *0, disabled.
ACPI: PCI Interrupt Link [LN2B] (IRQs 40 41 42 43) *0, disabled.
ACPI: PCI Interrupt Link [LN2C] (IRQs 40 41 42 43) *0, disabled.
ACPI: PCI Interrupt Link [LN2D] (IRQs 40 41 42 43) *0, disabled.
ACPI: PCI Interrupt Link [LK2N] (IRQs 44 45 46 47) *0, disabled.
ACPI: PCI Interrupt Link [LT3D] (IRQs 44 45 46 47) *0, disabled.
ACPI: PCI Interrupt Link [LT2E] (IRQs 44 45 46 47) *0, disabled.
ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - EE, should be EB [20070126]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
pnp 00:03: Plug and Play ACPI device, IDs PNP0800 (active)
pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
pnp 00:05: Plug and Play ACPI device, IDs PNP0501 (active)
pnp 00:06: Plug and Play ACPI device, IDs PNP0501 (active)
pnp 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:09: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
pnp 00:0a: Plug and Play ACPI device, IDs PNP0f12 PNP0f13 (active)
pnp 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:0c: Plug and Play ACPI device, IDs PNP0c02 (active)
pnp 00:0d: Plug and Play ACPI device, IDs PNP0c01 (active)
pnp 00:0e: Plug and Play ACPI device, IDs PNP0a03 (active)
pnp: PnP ACPI: found 15 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NET: Registered protocol family 8
NET: Registered protocol family 20
PCI-DMA: Disabling AGP.
PCI-DMA: aperture base @ f4000000 size 65536 KB
PCI-DMA: using GART IOMMU.
PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
ACPI: RTC can wake from S4
pnp: the driver 'system' has been registered
system 00:07: ioport range 0x190-0x193 has been reserved
system 00:07: ioport range 0x4d0-0x4d1 has been reserved
system 00:07: iomem range 0xffb80000-0xfffffffe could not be reserved
system 00:07: iomem range 0xdfefc000-0xdfefcfff could not be reserved
system 00:07: iomem range 0xdfefd000-0xdfefd3ff could not be reserved
system 00:07: iomem range 0xdfefe000-0xdfefe3ff could not be reserved
system 00:07: iomem range 0xdfeff000-0xdfefffff could not be reserved
system 00:07: iomem range 0xfefff000-0xfeffffff has been reserved
system 00:07: driver attached
system 00:08: ioport range 0xca2-0xca3 has been reserved
system 00:08: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:08: iomem range 0xfee00000-0xfeefffff could not be reserved
system 00:08: iomem range 0xfe200000-0xfebfffff could not be reserved
system 00:08: iomem range 0xfd500000-0xfd5fffff has been reserved
system 00:08: driver attached
system 00:0b: ioport range 0xa00-0xa0f has been reserved
system 00:0b: driver attached
system 00:0c: iomem range 0xe0000000-0xefffffff has been reserved
system 00:0c: driver attached
system 00:0d: iomem range 0x0-0x9ffff could not be reserved
system 00:0d: iomem range 0xc0000-0xdffff has been reserved
system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
system 00:0d: iomem range 0x100000-0xdfffffff could not be reserved
system 00:0d: iomem range 0x0-0x0 could not be reserved
system 00:0d: driver attached
PCI: Bridge: 0000:00:09.0
IO window: 9000-9fff
MEM window: fd800000-fe0fffff
PREFETCH window: fb400000-fd3fffff
PCI: Bridge: 0000:00:0b.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0c.0
IO window: disabled.
MEM window: fd700000-fd7fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0d.0
IO window: disabled.
MEM window: fd600000-fd6fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0e.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:09.0 to 64
PCI: Setting latency timer of device 0000:00:0b.0 to 64
PCI: Setting latency timer of device 0000:00:0c.0 to 64
PCI: Setting latency timer of device 0000:00:0d.0 to 64
PCI: Setting latency timer of device 0000:00:0e.0 to 64
PCI: Bridge: 0000:80:0d.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:80:0e.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:80:10.0
IO window: d000-dfff
MEM window: fe200000-feafffff
PREFETCH window: disabled.
PCI: Bridge: 0000:80:11.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:80:0d.0 to 64
PCI: Setting latency timer of device 0000:80:0e.0 to 64
NET: Registered protocol family 2
Time: acpi_pm clocksource has been installed.
Switched to high resolution mode on CPU 0
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 3
Switched to high resolution mode on CPU 4
Switched to high resolution mode on CPU 2
Switched to high resolution mode on CPU 6
Switched to high resolution mode on CPU 5
Switched to high resolution mode on CPU 7
IP route cache hash table entries: 1048576 (order: 11, 8388608 bytes)
TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 5446k freed
audit: initializing netlink socket (disabled)
audit(1234913487.632:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Found disabled HT MSI Mapping on 0000:00:0b.0
PCI: Found enabled HT MSI Mapping on 0000:00:00.0
PCI: Found disabled HT MSI Mapping on 0000:00:0c.0
PCI: Found enabled HT MSI Mapping on 0000:00:00.0
PCI: Found disabled HT MSI Mapping on 0000:00:0d.0
PCI: Found enabled HT MSI Mapping on 0000:00:00.0
PCI: Found disabled HT MSI Mapping on 0000:00:0e.0
PCI: Found enabled HT MSI Mapping on 0000:00:00.0
PCI: Found disabled HT MSI Mapping on 0000:80:0d.0
PCI: Found enabled HT MSI Mapping on 0000:80:00.0
PCI: Found disabled HT MSI Mapping on 0000:80:0e.0
PCI: Found enabled HT MSI Mapping on 0000:80:00.0
PCI: Setting latency timer of device 0000:00:0b.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0b.0:pcie00]
PCI: Setting latency timer of device 0000:00:0c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0c.0:pcie00]
PCI: Setting latency timer of device 0000:00:0d.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0d.0:pcie00]
PCI: Setting latency timer of device 0000:00:0e.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0e.0:pcie00]
PCI: Setting latency timer of device 0000:80:0d.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:80:0d.0:pcie00]
PCI: Setting latency timer of device 0000:80:0e.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:80:0e.0:pcie00]
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
pnp: the driver 'serial' has been registered
00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial 00:05: driver attached
00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
serial 00:06: driver attached
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
input: Macintosh mouse button emulation as /class/input/input0
pnp: the driver 'i8042 kbd' has been registered
i8042 kbd 00:09: driver attached
pnp: the driver 'i8042 aux' has been registered
i8042 aux 00:0a: driver attached
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f12:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
registered taskstats version 1
Freeing unused kernel memory: 316k freed
input: AT Translated Set 2 keyboard as /class/input/input1
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUS0] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 22, io mem 0xfe1fc000
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
pnp: the driver 'ide' has been registered
SCSI subsystem initialized
Fusion MPT base driver 3.04.06
Copyright (c) 1999-2007 LSI Corporation
Fusion MPT SAS Host driver 3.04.06
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
NFORCE-CK804: IDE controller (0x10de:0x0053 rev 0xa2) at PCI slot 0000:00:06.0
NFORCE-CK804: not 100% native mode: will probe irqs later
NFORCE-CK804: 0000:00:06.0 (rev a2) UDMA133 controller
ide0: BM-DMA at 0x0d00-0x0d07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0x0d08-0x0d0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hdb: TSSTcorpCD-ROM TS-L162C, ATAPI CD/DVD-ROM drive
hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdb: UDMA/33 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
tg3.c:v3.86 (November 9, 2007)
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 19
ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LNKA] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:03:00.0 to 64
eth0: Tigon3 [partno(BCM95721) rev 4101 PHY(5750)] (PCI Express) 10/100/1000Base-T Ethernet 00:d0:68:12:f6:fd
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] WireSpeed[1] TSOcap[1]
eth0: dma_rwctrl[76180000] dma_mask[64-bit]
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 18
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKD] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:02:00.0 to 64
eth1: Tigon3 [partno(BCM95721) rev 4101 PHY(5750)] (PCI Express) 10/100/1000Base-T Ethernet 00:d0:68:12:f6:fc
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
eth1: dma_rwctrl[76180000] dma_mask[64-bit]
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUS2] -> GSI 21 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:02.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: irq 21, io mem 0xfe1fdc00
libata version 3.00 loaded.
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
sata_nv 0000:00:07.0: version 3.5
ACPI: PCI Interrupt Link [LTID] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [LTID] -> GSI 20 (level, low) -> IRQ 20
sata_nv 0000:00:07.0: Using ADMA mode
PCI: Setting latency timer of device 0000:00:07.0 to 64
scsi0 : sata_nv
scsi1 : sata_nv
ata1: SATA max UDMA/133 cmd 0xb800 ctl 0xb400 bmdma 0xa800 irq 20
ata2: SATA max UDMA/133 cmd 0xb000 ctl 0xac00 bmdma 0xa808 irq 20
ata1: SATA link down (SStatus 0 SControl 300)
ata2: SATA link down (SStatus 0 SControl 300)
ACPI: PCI Interrupt Link [LTIE] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LTIE] -> GSI 22 (level, low) -> IRQ 22
sata_nv 0000:00:08.0: Using ADMA mode
PCI: Setting latency timer of device 0000:00:08.0 to 64
scsi2 : sata_nv
scsi3 : sata_nv
ata3: SATA max UDMA/133 cmd 0xcc00 ctl 0xc800 bmdma 0xbc00 irq 22
ata4: SATA max UDMA/133 cmd 0xc400 ctl 0xc000 bmdma 0xbc08 irq 22
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
ACPI: PCI Interrupt Link [LT2E] enabled at IRQ 47
ACPI: PCI Interrupt 0000:80:08.0[A] -> Link [LT2E] -> GSI 47 (level, low) -> IRQ 47
sata_nv 0000:80:08.0: Using ADMA mode
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 17
ACPI: PCI Interrupt 0000:05:07.0[A] -> Link [LNKC] -> <7>PCI: Setting latency timer of device 0000:80:08.0 to 64
GSI 17 (level, low) -> IRQ 17
scsi4 : sata_nv
scsi5 : sata_nv
ata5: SATA max UDMA/133 cmd 0xfc00 ctl 0xf800 bmdma 0xec00 irq 47
ata6: SATA max UDMA/133 cmd 0xf400 ctl 0xf000 bmdma 0xec08 irq 47
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[17] MMIO=[fe0ff800-fe0fffff] Max Packet=[2048] IR/IT contexts=[4/8]
ata5: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
ACPI: PCI Interrupt 0000:82:03.0[A] -> GSI 75 (level, low) -> IRQ 75
mptbase: ioc0: Initiating bringup
hdb: ATAPI 24X CD-ROM drive, 96kB Cache
Uniform CD-ROM driver Revision: 3.20
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000000000002244e]
ioc0: LSISAS1068 B1: Capabilities={Initiator}
scsi6 : ioc0: LSISAS1068 B1, FwRev=01120000h, Ports=1, MaxQ=511, IRQ=75
scsi 6:0:0:0: Direct-Access SEAGATE ST3146855SS RS02 PQ: 0 ANSI: 5
scsi 6:0:1:0: Direct-Access SEAGATE ST3146855SS RS02 PQ: 0 ANSI: 5
scsi 6:1:0:0: Direct-Access LSILOGIC Logical Volume 3000 PQ: 0 ANSI: 2
Driver 'sd' needs updating - please use bus_type methods
sd 6:1:0:0: [sda] 285155328 512-byte hardware sectors (146000 MB)
sd 6:1:0:0: [sda] Write Protect is off
sd 6:1:0:0: [sda] Mode Sense: 03 00 00 08
sd 6:1:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 6:1:0:0: [sda] 285155328 512-byte hardware sectors (146000 MB)
sd 6:1:0:0: [sda] Write Protect is off
sd 6:1:0:0: [sda] Mode Sense: 03 00 00 08
sd 6:1:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4
sd 6:1:0:0: [sda] Attached SCSI disk
Probing IDE interface ide1...
md: linear personality registered for level -1
md: multipath personality registered for level -4
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
xor: automatically using best checksumming function: generic_sse
generic_sse: 8660.000 MB/sec
xor: using function: generic_sse (8660.000 MB/sec)
async_tx: api initialized (sync-only)
raid6: int64x1 2538 MB/s
raid6: int64x2 3089 MB/s
raid6: int64x4 3283 MB/s
raid6: int64x8 2294 MB/s
raid6: sse2x1 3553 MB/s
raid6: sse2x2 5050 MB/s
raid6: sse2x4 5181 MB/s
raid6: using algorithm sse2x4 (5181 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: raid10 personality registered for level 10
Attempting manual resume
SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
XFS mounting filesystem sda2
Ending clean XFS mount for filesystem: sda2
input: Power Button (FF) as /class/input/input2
i2c-adapter i2c-0: nForce2 SMBus adapter at 0x2300
i2c-adapter i2c-1: nForce2 SMBus adapter at 0x2340
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input3
input: PC Speaker as /class/input/input4
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: HPC vendor_id 1022 device_id 7458 ss_vid 0 ss_did 0
shpchp: shpc_init: cannot reserve MMIO region
shpchp: HPC vendor_id 1022 device_id 7458 ss_vid 0 ss_did 0
shpchp: shpc_init: cannot reserve MMIO region
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ACPI: Power Button (CM) [PWRB]
Adding 1951856k swap on /dev/sda1. Priority:-1 extents:1 across:1951856k
loop: module loaded
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@xxxxxxxxxx
XFS mounting filesystem sda4
Ending clean XFS mount for filesystem: sda4
NET: Registered protocol family 10
lo: Disabled Privacy Extensions

Next message: Ingo Molnar: "Re: [PATCH 00/15] [git pull] for tip/tracing/ftrace"
Previous message: Ingo Molnar: "Re: tip: bzip2/lzma now in tip:x86/setup-lzma"
In reply to: Yinghai Lu: "Re: mpt fusion broken sometime since 2.6.24"
Next in thread: Yinghai Lu: "Re: mpt fusion broken sometime since 2.6.24"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]