Re: [PATCH 1/2] cs5535-gpio: add AMD CS5535/CS5536 GPIO driver support

[Tobias MÃller]

>> /**
>> * Some GPIO pins
>> * Â31-29,23 : reserved (always mask out)
>> * Â28 Â Â Â : Power Button
>> * Â26 Â Â Â : PME#
>> * Â22-16 Â Â: LPC
>> * Â14,15 Â Â: SMBus
>> * Â9,8 Â Â Â: UART1
>> * Â7 Â Â Â Â: PCI INTB
>> * Â3,4 Â Â Â: UART2/DDC
>> * Â2 Â Â Â Â: IDE_IRQ0
>> * Â1 Â Â Â Â: AC_BEEP
>> * Â0 Â Â Â Â: PCI INTA
>> *
>> * If a mask was not specified, be conservative and only allow:
>> * Â1,2,5,6,10-13,24,25,27
>> */
>>
>> I'll add this in my patch to clear it out.
>>
>
> But why are you being conservative in the first place? ÂIf something's
> using GPIOs, unless they're unmapped, you should allow it to use them
> without requiring a boot arg.
>
> For example, OLPC uses GPIO 7 for its DCON IRQ. ÂWith the masking
> scheme, OLPC will need to set that mask from the default. ÂI don't see
> the point of having the mask at all if other drivers in the kernel are
> going to be requesting GPIOs (presumably they know what they're doing).
Hmm... OK, this makes sense. So default mask allow everything exept
reserved pins and pin 28 (power button).

I think the mask is quite useful if you've critical things on GPIO pins
and they should be changeable (especially from userspace and when
non-root users are allowed to use userspace gpio).

>> >> + Â Â /* disable output aux 1 & 2 on this pin */
>> >> + Â Â __cs5535_gpio_clear(chip, offset, GPIO_OUTPUT_AUX1);
>> >> + Â Â __cs5535_gpio_clear(chip, offset, GPIO_OUTPUT_AUX2);
>> >> +
>> >> + Â Â /* disable input aux 1 on this pin */
>> >> + Â Â __cs5535_gpio_clear(chip, offset, GPIO_INPUT_AUX1);
>> >> +
>> >> + Â Â /* disable output */
>> >> + Â Â __cs5535_gpio_clear(chip, offset, GPIO_OUTPUT_ENABLE);
>> >> +
>> >> + Â Â /* enable input */
>> >> + Â Â __cs5535_gpio_set(chip, offset, GPIO_INPUT_ENABLE);
>> >
>> > I don't think this is the right place for all of this. ÂYour earlier
>> > email mentioned disabling OUT_AUX{1,2} for outputs, and IN_AUX for
>> > inputs. ÂI'm fine with doing that here, but I don't see why you're
>> > also disabling output and enabling input by default.
>>
>> I mentioned this in an ealier mail too. When I request the GPIO from
>> userspace the direction file always contains "in", so I thought
>> this is the standard direction after resetting as I should be in a
>> defined state after requesting. But I didn't found anything
>> about this in GPIO lib documentation, so I would be fine to change
>> this if there is any common default behavoir.
>
> To be honest, I'd have to play around with it a bit before I
> knew whether it actually breaks anything or not. I'm not sure if
> it would break anything on OLPC, and I don't have any other geode
> machines that do anything interesting w/ GPIOs.
>
> Maybe David can clear up whether this behavior is correct from the
> userspace GPIO usage standpoint..
This would be nice. But I wouldn't have a problem when those
two statements are removed. I just thought it's better to put them
in a defined state.
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/