Re: PowerPC PCI DMA issues (prefetch/coherency?)

[Hu Gang]

On Tue, 16 Jun 2009 14:58:27 +0100
Chris Pringle <chris.pringle@xxxxxxxxx> wrote:

> Hello All,
> 
> We're developing on a Freescale MPC8272 and are having some nasty 
> problems with PCI bus mastering and data corruption.
> 
> We have some custom hardware that is bus mastering, reading data from 
> the CPUs memory for it's own use. Most of the time, the data is correct, 
> however occasionally we are seeing data that appears to be from 
> somewhere else in memory (usually memory that has already been read by 
> the PCI device). The problem looks like stale data on the PCI bridge 
> prefetch buffers or a cache coherency problem, but we've been unable to 
> come up with a solution to our problem. It is my understanding that it 
> shouldn't be a cache coherency problem as the CPU cache should be 
> snooped as the data is read from memory. Even if it were an issue, the 
> pci_map_sg* functions should have sorted out any cache coherency issues 
> before the DMA operation started.
> 
> I've not been able to find anything on the Freescale data sheet that 
> provides any way of flushing the prefetch cache on the PCI bridge. We've 
> done a bit of experimenting, and found that turning off prefetch appears 
> to solve (or possibly mask?) the problem (at the expensive of massive 
> performance problems). I've also tried DMA'ing two adjacent userspace 
> buffers in memory (from the same page), and see corruption on the second 
> buffer. If I populate both buffers, then DMA them both, the data is 
> fine. If I populate the first, DMA the first, then populate the second 
> and DMA the second, corruption occurs at the start of the second buffer. 
> If I add 8-32 bytes of padding between the buffers, the problem goes away.
> 
> The PCI spec says that the PCI bridge is supposed to flush any data from 
> it's prefetch buffers that are not read by the bus master, so 
> technically, this isn't supposed to happen.
> 
> I've tried making sure that buffers are cache line (and page) aligned, 
> and are multiples of cache lines, but it's made no difference. PIO mode 
> works fine, and I've checked the data with the CPU just before, and 
> immediately after the DMA and the driver sees no data integrity issues. 
> There are memory write barriers just before the DMA start, so all the 
> registers should be correct before the DMA starts.
> 
> For background info, the device doing the bus mastering is a Xilinx 
> Virtex 5 FPGA. We've monitored the data as it comes off the PCI bus 
> using ChipScope - so the firmware should not be manipulating the data in 
> any way.
> 
> We have some hardware/firmware/drivers that has a lot of common code 
> that runs on an x86 platform (as opposed to powerpc), and that works 
> without any issues whatsoever.
> 
> Has anyone got any ideas what this might be? Does anyone of know issues 
> with PCI bridges on the PowerPC platform? Is there extra things that 
> need to be done from the driver when DMAing on PowerPC (I've looked at 
> other drivers and there's nothing obvious). The chip errata doesn't have 
> anything on it that looks like it could cause this.
> 
> I'm really hoping this is something that we're doing wrong in the driver 
> or the firmware, but we've been through both the firmware and drivers 
> countless times and are unable to see anything wrong.
> 
> Any thoughts/ideas would be much appreciated!
> 
> Regards,
> Chris

Can you try allocate the data buffer using dma_alloc_coherent, that can making
the data coherency.

I got the similar issues in the arm cpu with a dma device base on spartan3, using
the dma_alloc_coherent making it works well.

hope this help. 

thanks.
-- 
steve
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/