Re: sky2 panic in 2.6.32.1 under load (new oops)

[Stephen Hemminger]

On Fri, 25 Dec 2009 22:23:51 -0500
Michael Breuer <mbreuer@xxxxxxxxxx> wrote:

> On 12/25/2009 6:22 PM, Stephen Hemminger wrote:
> > On Fri, 25 Dec 2009 11:28:55 -0500
> > Michael Breuer<mbreuer@xxxxxxxxxx>  wrote:
> >
> >    
> >>    More data points - I'm able to reliably recreate this now.
> >> While I thought it was coincidence, each and every time I hit this issue
> >> there is a DHCP renew event immediately before the first error.
> >> The crash occurs while under load - in my case seems that the traffic is
> >> actually IPV6 (hadn't noticed that before).
> >> I ran nethogs on a remote display - the reported rx rate on the IPV6 smb
> >> connection at the time of the lockup was 33889.688 KB/sec on a 1gbit
> >> nic. I've got two events like this - don't recall if the earlier one was
> >> the exact same # - but it was in the ballpark.
> >>
> >> On 12/24/2009 2:01 AM, Andrew Morton wrote:
> >>      
> >>> cc's added again.
> >>>
> >>> On Wed, 23 Dec 2009 17:54:27 -0500 Michael Breuer<mbreuer@xxxxxxxxxx>   wrote:
> >>>
> >>>
> >>>        
> >>>> Ok - not the firmware.  Ran another Windows backup and sky2 went down.
> >>>>
> >>>> Nothing in dmesg.old - have oops in syslog. System became unresponsive
> >>>> and watchdog kicked in after a minute.
> >>>>
> >>>> Also note that I have a similar oops with VT-D disabled (posted here on
> >>>> 12/5). I'm attaching the oops from that below this oops for comparison.
> >>>> That also happened under similar load.
> >>>>
> >>>> On the assumption that I can recreate this (although it takes a while)
> >>>> please let me know how I can help.
> >>>>
> >>>> What's in my log (starting with an smbd error about 2 min before the
> >>>> oops (note: the dchpd is not the system doing the backup).
> >>>>
> >>>>          
> >>> This (nastily wordwrapped) oops appers to be quite different from
> >>> Berck's one.
> >>>
> >>>
> >>>        
> > What is the MTU?
> >    
> 1500
> >>      

It looks like the problem only shows up for packets generated by DHCP,
and these come through AF_PACKET. The problem maybe related to how this
packets are fragmented into header and page, in a different way than other
packets confusing the driver or DMA engine.

Does this help?
-----

--- a/drivers/net/sky2.c	2009-12-26 09:50:20.869565022 -0800
+++ b/drivers/net/sky2.c	2009-12-26 09:55:54.620645355 -0800
@@ -1616,6 +1616,13 @@ static netdev_tx_t sky2_xmit_frame(struc
  	if (unlikely(tx_avail(sky2) < tx_le_req(skb)))
   		return NETDEV_TX_BUSY;
 
+	if (!pskb_may_pull(skb, ETH_HLEN)) {
+		if (net_ratelimit())
+			pr_info(PFX "%s: packet missing ether header (%d)?",
+				dev->name, skb->len);
+		goto drop;
+	}
+
 	len = skb_headlen(skb);
 	mapping = pci_map_single(hw->pdev, skb->data, len, PCI_DMA_TODEVICE);
 
@@ -1761,6 +1768,7 @@ mapping_unwind:
 mapping_error:
 	if (net_ratelimit())
 		dev_warn(&hw->pdev->dev, "%s: tx mapping error\n", dev->name);
+drop:
 	dev_kfree_skb(skb);
 	return NETDEV_TX_OK;
 }




-- 
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/