[PATCH 46/68] pata_cs5535: move code to be re-used by ide2libata to pata_cs5535.h
From: Bartlomiej Zolnierkiewicz
Date: Fri Jan 29 2010 - 11:08:29 EST
From: Bartlomiej Zolnierkiewicz <bzolnier@xxxxxxxxx>
Subject: [PATCH] pata_cs5535: move code to be re-used by ide2libata to pata_cs5535.h
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@xxxxxxxxx>
---
drivers/ata/pata_cs5535.c | 113 ---------------------------------------------
drivers/ata/pata_cs5535.h | 114 ++++++++++++++++++++++++++++++++++++++++++++++
2 files changed, 115 insertions(+), 112 deletions(-)
Index: b/drivers/ata/pata_cs5535.c
===================================================================
--- a/drivers/ata/pata_cs5535.c
+++ b/drivers/ata/pata_cs5535.c
@@ -41,118 +41,7 @@
#define DRV_NAME "cs5535"
#define DRV_VERSION "0.2.12"
-/*
- * The Geode (Aka Athlon GX now) uses an internal MSR based
- * bus system for control. Demented but there you go.
- */
-
-#define MSR_ATAC_BASE 0x51300000
-#define ATAC_GLD_MSR_CAP (MSR_ATAC_BASE+0)
-#define ATAC_GLD_MSR_CONFIG (MSR_ATAC_BASE+0x01)
-#define ATAC_GLD_MSR_SMI (MSR_ATAC_BASE+0x02)
-#define ATAC_GLD_MSR_ERROR (MSR_ATAC_BASE+0x03)
-#define ATAC_GLD_MSR_PM (MSR_ATAC_BASE+0x04)
-#define ATAC_GLD_MSR_DIAG (MSR_ATAC_BASE+0x05)
-#define ATAC_IO_BAR (MSR_ATAC_BASE+0x08)
-#define ATAC_RESET (MSR_ATAC_BASE+0x10)
-#define ATAC_CH0D0_PIO (MSR_ATAC_BASE+0x20)
-#define ATAC_CH0D0_DMA (MSR_ATAC_BASE+0x21)
-#define ATAC_CH0D1_PIO (MSR_ATAC_BASE+0x22)
-#define ATAC_CH0D1_DMA (MSR_ATAC_BASE+0x23)
-#define ATAC_PCI_ABRTERR (MSR_ATAC_BASE+0x24)
-
-#define ATAC_BM0_CMD_PRIM 0x00
-#define ATAC_BM0_STS_PRIM 0x02
-#define ATAC_BM0_PRD 0x04
-
-#define CS5535_CABLE_DETECT 0x48
-
-/**
- * cs5535_cable_detect - detect cable type
- * @ap: Port to detect on
- *
- * Perform cable detection for ATA66 capable cable. Return a libata
- * cable type.
- */
-
-static int cs5535_cable_detect(struct ata_port *ap)
-{
- u8 cable;
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
-
- pci_read_config_byte(pdev, CS5535_CABLE_DETECT, &cable);
- if (cable & 1)
- return ATA_CBL_PATA80;
- else
- return ATA_CBL_PATA40;
-}
-
-/**
- * cs5535_set_piomode - PIO setup
- * @ap: ATA interface
- * @adev: device on the interface
- *
- * Set our PIO requirements. The CS5535 is pretty clean about all this
- */
-
-static void cs5535_set_piomode(struct ata_port *ap, struct ata_device *adev)
-{
- static const u16 pio_timings[5] = {
- 0xF7F4, 0xF173, 0x8141, 0x5131, 0x1131
- };
- static const u16 pio_cmd_timings[5] = {
- 0xF7F4, 0x53F3, 0x13F1, 0x5131, 0x1131
- };
- u32 reg, dummy;
- struct ata_device *pair = ata_dev_pair(adev);
-
- int mode = adev->pio_mode - XFER_PIO_0;
- int cmdmode = mode;
-
- /* Command timing has to be for the lowest of the pair of devices */
- if (pair) {
- int pairmode = pair->pio_mode - XFER_PIO_0;
- cmdmode = min(mode, pairmode);
- /* Write the other drive timing register if it changed */
- if (cmdmode < pairmode)
- wrmsr(ATAC_CH0D0_PIO + 2 * pair->devno,
- pio_cmd_timings[cmdmode] << 16 | pio_timings[pairmode], 0);
- }
- /* Write the drive timing register */
- wrmsr(ATAC_CH0D0_PIO + 2 * adev->devno,
- pio_cmd_timings[cmdmode] << 16 | pio_timings[mode], 0);
-
- /* Set the PIO "format 1" bit in the DMA timing register */
- rdmsr(ATAC_CH0D0_DMA + 2 * adev->devno, reg, dummy);
- wrmsr(ATAC_CH0D0_DMA + 2 * adev->devno, reg | 0x80000000UL, 0);
-}
-
-/**
- * cs5535_set_dmamode - DMA timing setup
- * @ap: ATA interface
- * @adev: Device being configured
- *
- */
-
-static void cs5535_set_dmamode(struct ata_port *ap, struct ata_device *adev)
-{
- static const u32 udma_timings[5] = {
- 0x7F7436A1, 0x7F733481, 0x7F723261, 0x7F713161, 0x7F703061
- };
- static const u32 mwdma_timings[3] = {
- 0x7F0FFFF3, 0x7F035352, 0x7F024241
- };
- u32 reg, dummy;
- int mode = adev->dma_mode;
-
- rdmsr(ATAC_CH0D0_DMA + 2 * adev->devno, reg, dummy);
- reg &= 0x80000000UL;
- if (mode >= XFER_UDMA_0)
- reg |= udma_timings[mode - XFER_UDMA_0];
- else
- reg |= mwdma_timings[mode - XFER_MW_DMA_0];
- wrmsr(ATAC_CH0D0_DMA + 2 * adev->devno, reg, 0);
-}
+#include "pata_cs5535.h"
static struct scsi_host_template cs5535_sht = {
ATA_BMDMA_SHT(DRV_NAME),
Index: b/drivers/ata/pata_cs5535.h
===================================================================
--- /dev/null
+++ b/drivers/ata/pata_cs5535.h
@@ -0,0 +1,114 @@
+
+/*
+ * The Geode (Aka Athlon GX now) uses an internal MSR based
+ * bus system for control. Demented but there you go.
+ */
+
+#define MSR_ATAC_BASE 0x51300000
+#define ATAC_GLD_MSR_CAP (MSR_ATAC_BASE+0)
+#define ATAC_GLD_MSR_CONFIG (MSR_ATAC_BASE+0x01)
+#define ATAC_GLD_MSR_SMI (MSR_ATAC_BASE+0x02)
+#define ATAC_GLD_MSR_ERROR (MSR_ATAC_BASE+0x03)
+#define ATAC_GLD_MSR_PM (MSR_ATAC_BASE+0x04)
+#define ATAC_GLD_MSR_DIAG (MSR_ATAC_BASE+0x05)
+#define ATAC_IO_BAR (MSR_ATAC_BASE+0x08)
+#define ATAC_RESET (MSR_ATAC_BASE+0x10)
+#define ATAC_CH0D0_PIO (MSR_ATAC_BASE+0x20)
+#define ATAC_CH0D0_DMA (MSR_ATAC_BASE+0x21)
+#define ATAC_CH0D1_PIO (MSR_ATAC_BASE+0x22)
+#define ATAC_CH0D1_DMA (MSR_ATAC_BASE+0x23)
+#define ATAC_PCI_ABRTERR (MSR_ATAC_BASE+0x24)
+
+#define ATAC_BM0_CMD_PRIM 0x00
+#define ATAC_BM0_STS_PRIM 0x02
+#define ATAC_BM0_PRD 0x04
+
+#define CS5535_CABLE_DETECT 0x48
+
+/**
+ * cs5535_cable_detect - detect cable type
+ * @ap: Port to detect on
+ *
+ * Perform cable detection for ATA66 capable cable. Return a libata
+ * cable type.
+ */
+
+static int cs5535_cable_detect(struct ata_port *ap)
+{
+ u8 cable;
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+ pci_read_config_byte(pdev, CS5535_CABLE_DETECT, &cable);
+ if (cable & 1)
+ return ATA_CBL_PATA80;
+ else
+ return ATA_CBL_PATA40;
+}
+
+/**
+ * cs5535_set_piomode - PIO setup
+ * @ap: ATA interface
+ * @adev: device on the interface
+ *
+ * Set our PIO requirements. The CS5535 is pretty clean about all this
+ */
+
+static void cs5535_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ static const u16 pio_timings[5] = {
+ 0xF7F4, 0xF173, 0x8141, 0x5131, 0x1131
+ };
+ static const u16 pio_cmd_timings[5] = {
+ 0xF7F4, 0x53F3, 0x13F1, 0x5131, 0x1131
+ };
+ u32 reg, dummy;
+ struct ata_device *pair = ata_dev_pair(adev);
+
+ int mode = adev->pio_mode - XFER_PIO_0;
+ int cmdmode = mode;
+
+ /* Command timing has to be for the lowest of the pair of devices */
+ if (pair) {
+ int pairmode = pair->pio_mode - XFER_PIO_0;
+ cmdmode = min(mode, pairmode);
+ /* Write the other drive timing register if it changed */
+ if (cmdmode < pairmode)
+ wrmsr(ATAC_CH0D0_PIO + 2 * pair->devno,
+ pio_cmd_timings[cmdmode] << 16 |
+ pio_timings[pairmode], 0);
+ }
+ /* Write the drive timing register */
+ wrmsr(ATAC_CH0D0_PIO + 2 * adev->devno,
+ pio_cmd_timings[cmdmode] << 16 | pio_timings[mode], 0);
+
+ /* Set the PIO "format 1" bit in the DMA timing register */
+ rdmsr(ATAC_CH0D0_DMA + 2 * adev->devno, reg, dummy);
+ wrmsr(ATAC_CH0D0_DMA + 2 * adev->devno, reg | 0x80000000UL, 0);
+}
+
+/**
+ * cs5535_set_dmamode - DMA timing setup
+ * @ap: ATA interface
+ * @adev: Device being configured
+ *
+ */
+
+static void cs5535_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+ static const u32 udma_timings[5] = {
+ 0x7F7436A1, 0x7F733481, 0x7F723261, 0x7F713161, 0x7F703061
+ };
+ static const u32 mwdma_timings[3] = {
+ 0x7F0FFFF3, 0x7F035352, 0x7F024241
+ };
+ u32 reg, dummy;
+ int mode = adev->dma_mode;
+
+ rdmsr(ATAC_CH0D0_DMA + 2 * adev->devno, reg, dummy);
+ reg &= 0x80000000UL;
+ if (mode >= XFER_UDMA_0)
+ reg |= udma_timings[mode - XFER_UDMA_0];
+ else
+ reg |= mwdma_timings[mode - XFER_MW_DMA_0];
+ wrmsr(ATAC_CH0D0_DMA + 2 * adev->devno, reg, 0);
+}
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/