[PATCH 5/6] early_res: seperate common memmap func from e820.c tofw_memmap.c
From: Yinghai Lu
Date: Wed Mar 10 2010 - 16:26:34 EST
move it to kernel/fw_memmap.c from arch/x86/kernel/e820.c
Signed-off-by: Yinghai Lu <yinghai@xxxxxxxxxx>
---
arch/x86/include/asm/e820.h | 130 -----
arch/x86/kernel/e820.c | 1142 --------------------------------------------
include/linux/bootmem.h | 2
include/linux/fw_memmap.h | 114 ++++
kernel/Makefile | 2
kernel/fw_memmap.c | 1134 +++++++++++++++++++++++++++++++++++++++++++
6 files changed, 1290 insertions(+), 1234 deletions(-)
Index: linux-2.6/arch/x86/kernel/e820.c
===================================================================
--- linux-2.6.orig/arch/x86/kernel/e820.c
+++ linux-2.6/arch/x86/kernel/e820.c
@@ -12,31 +12,11 @@
#include <linux/types.h>
#include <linux/init.h>
#include <linux/bootmem.h>
-#include <linux/pfn.h>
#include <linux/suspend.h>
-#include <linux/firmware-map.h>
#include <asm/e820.h>
-#include <asm/proto.h>
#include <asm/setup.h>
-/*
- * The e820 map is the map that gets modified e.g. with command line parameters
- * and that is also registered with modifications in the kernel resource tree
- * with the iomem_resource as parent.
- *
- * The e820_saved is directly saved after the BIOS-provided memory map is
- * copied. It doesn't get modified afterwards. It's registered for the
- * /sys/firmware/memmap interface.
- *
- * That memory map is not modified and is used as base for kexec. The kexec'd
- * kernel should get the same memory map as the firmware provides. Then the
- * user can e.g. boot the original kernel with mem=1G while still booting the
- * next kernel with full memory.
- */
-static struct e820map __initdata e820;
-static struct e820map __initdata e820_saved;
-
/* For PCI or other memory-mapped resources */
unsigned long pci_mem_start = 0xaeedbabe;
#ifdef CONFIG_PCI
@@ -44,577 +24,6 @@ EXPORT_SYMBOL(pci_mem_start);
#endif
/*
- * This function checks if any part of the range <start,end> is mapped
- * with type.
- * phys_pud_init() is using it and is _meminit, but we have !after_bootmem
- * so could use refok here
- */
-int __init_refok e820_any_mapped(u64 start, u64 end, unsigned type)
-{
- int i;
-
- for (i = 0; i < e820.nr_map; i++) {
- struct e820entry *ei = &e820.map[i];
-
- if (type && ei->type != type)
- continue;
- if (ei->addr >= end || ei->addr + ei->size <= start)
- continue;
- return 1;
- }
- return 0;
-}
-
-/*
- * This function checks if the entire range <start,end> is mapped with type.
- *
- * Note: this function only works correct if the e820 table is sorted and
- * not-overlapping, which is the case
- */
-int __init e820_all_mapped(u64 start, u64 end, unsigned type)
-{
- int i;
-
- for (i = 0; i < e820.nr_map; i++) {
- struct e820entry *ei = &e820.map[i];
-
- if (type && ei->type != type)
- continue;
- /* is the region (part) in overlap with the current region ?*/
- if (ei->addr >= end || ei->addr + ei->size <= start)
- continue;
-
- /* if the region is at the beginning of <start,end> we move
- * start to the end of the region since it's ok until there
- */
- if (ei->addr <= start)
- start = ei->addr + ei->size;
- /*
- * if start is now at or beyond end, we're done, full
- * coverage
- */
- if (start >= end)
- return 1;
- }
- return 0;
-}
-
-/*
- * Add a memory region to the kernel e820 map.
- */
-static void __init __e820_add_region(struct e820map *e820x, u64 start, u64 size,
- int type)
-{
- int x = e820x->nr_map;
-
- if (x >= ARRAY_SIZE(e820x->map)) {
- printk(KERN_ERR "Ooops! Too many entries in the memory map!\n");
- return;
- }
-
- e820x->map[x].addr = start;
- e820x->map[x].size = size;
- e820x->map[x].type = type;
- e820x->nr_map++;
-}
-
-void __init e820_add_region(u64 start, u64 size, int type)
-{
- __e820_add_region(&e820, start, size, type);
-}
-
-static void __init e820_print_type(u32 type)
-{
- switch (type) {
- case E820_RAM:
- case E820_RESERVED_KERN:
- printk(KERN_CONT "(usable)");
- break;
- case E820_RESERVED:
- printk(KERN_CONT "(reserved)");
- break;
- case E820_ACPI:
- printk(KERN_CONT "(ACPI data)");
- break;
- case E820_NVS:
- printk(KERN_CONT "(ACPI NVS)");
- break;
- case E820_UNUSABLE:
- printk(KERN_CONT "(unusable)");
- break;
- default:
- printk(KERN_CONT "type %u", type);
- break;
- }
-}
-
-void __init e820_print_map(char *who)
-{
- int i;
-
- for (i = 0; i < e820.nr_map; i++) {
- printk(KERN_INFO " %s: %016Lx - %016Lx ", who,
- (unsigned long long) e820.map[i].addr,
- (unsigned long long)
- (e820.map[i].addr + e820.map[i].size));
- e820_print_type(e820.map[i].type);
- printk(KERN_CONT "\n");
- }
-}
-
-/*
- * Sanitize the BIOS e820 map.
- *
- * Some e820 responses include overlapping entries. The following
- * replaces the original e820 map with a new one, removing overlaps,
- * and resolving conflicting memory types in favor of highest
- * numbered type.
- *
- * The input parameter biosmap points to an array of 'struct
- * e820entry' which on entry has elements in the range [0, *pnr_map)
- * valid, and which has space for up to max_nr_map entries.
- * On return, the resulting sanitized e820 map entries will be in
- * overwritten in the same location, starting at biosmap.
- *
- * The integer pointed to by pnr_map must be valid on entry (the
- * current number of valid entries located at biosmap) and will
- * be updated on return, with the new number of valid entries
- * (something no more than max_nr_map.)
- *
- * The return value from sanitize_e820_map() is zero if it
- * successfully 'sanitized' the map entries passed in, and is -1
- * if it did nothing, which can happen if either of (1) it was
- * only passed one map entry, or (2) any of the input map entries
- * were invalid (start + size < start, meaning that the size was
- * so big the described memory range wrapped around through zero.)
- *
- * Visually we're performing the following
- * (1,2,3,4 = memory types)...
- *
- * Sample memory map (w/overlaps):
- * ____22__________________
- * ______________________4_
- * ____1111________________
- * _44_____________________
- * 11111111________________
- * ____________________33__
- * ___________44___________
- * __________33333_________
- * ______________22________
- * ___________________2222_
- * _________111111111______
- * _____________________11_
- * _________________4______
- *
- * Sanitized equivalent (no overlap):
- * 1_______________________
- * _44_____________________
- * ___1____________________
- * ____22__________________
- * ______11________________
- * _________1______________
- * __________3_____________
- * ___________44___________
- * _____________33_________
- * _______________2________
- * ________________1_______
- * _________________4______
- * ___________________2____
- * ____________________33__
- * ______________________4_
- */
-
-static int __init __sanitize_e820_map(struct e820entry *biosmap, int max_nr_map,
- u32 *pnr_map)
-{
- struct change_member {
- struct e820entry *pbios; /* pointer to original bios entry */
- unsigned long long addr; /* address for this change point */
- };
- static struct change_member change_point_list[2*E820_X_MAX] __initdata;
- static struct change_member *change_point[2*E820_X_MAX] __initdata;
- static struct e820entry *overlap_list[E820_X_MAX] __initdata;
- static struct e820entry new_bios[E820_X_MAX] __initdata;
- struct change_member *change_tmp;
- unsigned long current_type, last_type;
- unsigned long long last_addr;
- int chgidx, still_changing;
- int overlap_entries;
- int new_bios_entry;
- int old_nr, new_nr, chg_nr;
- int i;
-
- /* if there's only one memory region, don't bother */
- if (*pnr_map < 2)
- return -1;
-
- old_nr = *pnr_map;
- BUG_ON(old_nr > max_nr_map);
-
- /* bail out if we find any unreasonable addresses in bios map */
- for (i = 0; i < old_nr; i++)
- if (biosmap[i].addr + biosmap[i].size < biosmap[i].addr)
- return -1;
-
- /* create pointers for initial change-point information (for sorting) */
- for (i = 0; i < 2 * old_nr; i++)
- change_point[i] = &change_point_list[i];
-
- /* record all known change-points (starting and ending addresses),
- omitting those that are for empty memory regions */
- chgidx = 0;
- for (i = 0; i < old_nr; i++) {
- if (biosmap[i].size != 0) {
- change_point[chgidx]->addr = biosmap[i].addr;
- change_point[chgidx++]->pbios = &biosmap[i];
- change_point[chgidx]->addr = biosmap[i].addr +
- biosmap[i].size;
- change_point[chgidx++]->pbios = &biosmap[i];
- }
- }
- chg_nr = chgidx;
-
- /* sort change-point list by memory addresses (low -> high) */
- still_changing = 1;
- while (still_changing) {
- still_changing = 0;
- for (i = 1; i < chg_nr; i++) {
- unsigned long long curaddr, lastaddr;
- unsigned long long curpbaddr, lastpbaddr;
-
- curaddr = change_point[i]->addr;
- lastaddr = change_point[i - 1]->addr;
- curpbaddr = change_point[i]->pbios->addr;
- lastpbaddr = change_point[i - 1]->pbios->addr;
-
- /*
- * swap entries, when:
- *
- * curaddr > lastaddr or
- * curaddr == lastaddr and curaddr == curpbaddr and
- * lastaddr != lastpbaddr
- */
- if (curaddr < lastaddr ||
- (curaddr == lastaddr && curaddr == curpbaddr &&
- lastaddr != lastpbaddr)) {
- change_tmp = change_point[i];
- change_point[i] = change_point[i-1];
- change_point[i-1] = change_tmp;
- still_changing = 1;
- }
- }
- }
-
- /* create a new bios memory map, removing overlaps */
- overlap_entries = 0; /* number of entries in the overlap table */
- new_bios_entry = 0; /* index for creating new bios map entries */
- last_type = 0; /* start with undefined memory type */
- last_addr = 0; /* start with 0 as last starting address */
-
- /* loop through change-points, determining affect on the new bios map */
- for (chgidx = 0; chgidx < chg_nr; chgidx++) {
- /* keep track of all overlapping bios entries */
- if (change_point[chgidx]->addr ==
- change_point[chgidx]->pbios->addr) {
- /*
- * add map entry to overlap list (> 1 entry
- * implies an overlap)
- */
- overlap_list[overlap_entries++] =
- change_point[chgidx]->pbios;
- } else {
- /*
- * remove entry from list (order independent,
- * so swap with last)
- */
- for (i = 0; i < overlap_entries; i++) {
- if (overlap_list[i] ==
- change_point[chgidx]->pbios)
- overlap_list[i] =
- overlap_list[overlap_entries-1];
- }
- overlap_entries--;
- }
- /*
- * if there are overlapping entries, decide which
- * "type" to use (larger value takes precedence --
- * 1=usable, 2,3,4,4+=unusable)
- */
- current_type = 0;
- for (i = 0; i < overlap_entries; i++)
- if (overlap_list[i]->type > current_type)
- current_type = overlap_list[i]->type;
- /*
- * continue building up new bios map based on this
- * information
- */
- if (current_type != last_type) {
- if (last_type != 0) {
- new_bios[new_bios_entry].size =
- change_point[chgidx]->addr - last_addr;
- /*
- * move forward only if the new size
- * was non-zero
- */
- if (new_bios[new_bios_entry].size != 0)
- /*
- * no more space left for new
- * bios entries ?
- */
- if (++new_bios_entry >= max_nr_map)
- break;
- }
- if (current_type != 0) {
- new_bios[new_bios_entry].addr =
- change_point[chgidx]->addr;
- new_bios[new_bios_entry].type = current_type;
- last_addr = change_point[chgidx]->addr;
- }
- last_type = current_type;
- }
- }
- /* retain count for new bios entries */
- new_nr = new_bios_entry;
-
- /* copy new bios mapping into original location */
- memcpy(biosmap, new_bios, new_nr * sizeof(struct e820entry));
- *pnr_map = new_nr;
-
- return 0;
-}
-
-int __init sanitize_e820_map(void)
-{
- return __sanitize_e820_map(e820.map, ARRAY_SIZE(e820.map), &e820.nr_map);
-}
-
-static int __init __append_e820_map(struct e820entry *biosmap, int nr_map)
-{
- while (nr_map) {
- u64 start = biosmap->addr;
- u64 size = biosmap->size;
- u64 end = start + size;
- u32 type = biosmap->type;
-
- /* Overflow in 64 bits? Ignore the memory map. */
- if (start > end)
- return -1;
-
- e820_add_region(start, size, type);
-
- biosmap++;
- nr_map--;
- }
- return 0;
-}
-
-/*
- * Copy the BIOS e820 map into a safe place.
- *
- * Sanity-check it while we're at it..
- *
- * If we're lucky and live on a modern system, the setup code
- * will have given us a memory map that we can use to properly
- * set up memory. If we aren't, we'll fake a memory map.
- */
-static int __init append_e820_map(struct e820entry *biosmap, int nr_map)
-{
- /* Only one memory region (or negative)? Ignore it */
- if (nr_map < 2)
- return -1;
-
- return __append_e820_map(biosmap, nr_map);
-}
-
-static u64 __init __e820_update_range(struct e820map *e820x, u64 start,
- u64 size, unsigned old_type,
- unsigned new_type)
-{
- u64 end;
- unsigned int i;
- u64 real_updated_size = 0;
-
- BUG_ON(old_type == new_type);
-
- if (size > (ULLONG_MAX - start))
- size = ULLONG_MAX - start;
-
- end = start + size;
- printk(KERN_DEBUG "e820 update range: %016Lx - %016Lx ",
- (unsigned long long) start,
- (unsigned long long) end);
- e820_print_type(old_type);
- printk(KERN_CONT " ==> ");
- e820_print_type(new_type);
- printk(KERN_CONT "\n");
-
- for (i = 0; i < e820x->nr_map; i++) {
- struct e820entry *ei = &e820x->map[i];
- u64 final_start, final_end;
- u64 ei_end;
-
- if (ei->type != old_type)
- continue;
-
- ei_end = ei->addr + ei->size;
- /* totally covered by new range? */
- if (ei->addr >= start && ei_end <= end) {
- ei->type = new_type;
- real_updated_size += ei->size;
- continue;
- }
-
- /* new range is totally covered? */
- if (ei->addr < start && ei_end > end) {
- __e820_add_region(e820x, start, size, new_type);
- __e820_add_region(e820x, end, ei_end - end, ei->type);
- ei->size = start - ei->addr;
- real_updated_size += size;
- continue;
- }
-
- /* partially covered */
- final_start = max(start, ei->addr);
- final_end = min(end, ei_end);
- if (final_start >= final_end)
- continue;
-
- __e820_add_region(e820x, final_start, final_end - final_start,
- new_type);
-
- real_updated_size += final_end - final_start;
-
- /*
- * left range could be head or tail, so need to update
- * size at first.
- */
- ei->size -= final_end - final_start;
- if (ei->addr < final_start)
- continue;
- ei->addr = final_end;
- }
- return real_updated_size;
-}
-
-u64 __init e820_update_range(u64 start, u64 size, unsigned old_type,
- unsigned new_type)
-{
- return __e820_update_range(&e820, start, size, old_type, new_type);
-}
-
-static u64 __init e820_update_range_saved(u64 start, u64 size,
- unsigned old_type, unsigned new_type)
-{
- return __e820_update_range(&e820_saved, start, size, old_type,
- new_type);
-}
-
-/* make e820 not cover the range */
-u64 __init e820_remove_range(u64 start, u64 size, unsigned old_type,
- int checktype)
-{
- int i;
- u64 end;
- u64 real_removed_size = 0;
-
- if (size > (ULLONG_MAX - start))
- size = ULLONG_MAX - start;
-
- end = start + size;
- printk(KERN_DEBUG "e820 remove range: %016Lx - %016Lx ",
- (unsigned long long) start,
- (unsigned long long) end);
- e820_print_type(old_type);
- printk(KERN_CONT "\n");
-
- for (i = 0; i < e820.nr_map; i++) {
- struct e820entry *ei = &e820.map[i];
- u64 final_start, final_end;
-
- if (checktype && ei->type != old_type)
- continue;
- /* totally covered? */
- if (ei->addr >= start &&
- (ei->addr + ei->size) <= (start + size)) {
- real_removed_size += ei->size;
- memset(ei, 0, sizeof(struct e820entry));
- continue;
- }
- /* partially covered */
- final_start = max(start, ei->addr);
- final_end = min(start + size, ei->addr + ei->size);
- if (final_start >= final_end)
- continue;
- real_removed_size += final_end - final_start;
-
- ei->size -= final_end - final_start;
- if (ei->addr < final_start)
- continue;
- ei->addr = final_end;
- }
- return real_removed_size;
-}
-
-void __init update_e820(void)
-{
- u32 nr_map;
-
- nr_map = e820.nr_map;
- if (__sanitize_e820_map(e820.map, ARRAY_SIZE(e820.map), &nr_map))
- return;
- e820.nr_map = nr_map;
- printk(KERN_INFO "modified physical RAM map:\n");
- e820_print_map("modified");
-}
-static void __init update_e820_saved(void)
-{
- u32 nr_map;
-
- nr_map = e820_saved.nr_map;
- if (__sanitize_e820_map(e820_saved.map, ARRAY_SIZE(e820_saved.map), &nr_map))
- return;
- e820_saved.nr_map = nr_map;
-}
-#define MAX_GAP_END 0x100000000ull
-/*
- * Search for a gap in the e820 memory space from start_addr to end_addr.
- */
-__init int e820_search_gap(unsigned long *gapstart, unsigned long *gapsize,
- unsigned long start_addr, unsigned long long end_addr)
-{
- unsigned long long last;
- int i = e820.nr_map;
- int found = 0;
-
- last = (end_addr && end_addr < MAX_GAP_END) ? end_addr : MAX_GAP_END;
-
- while (--i >= 0) {
- unsigned long long start = e820.map[i].addr;
- unsigned long long end = start + e820.map[i].size;
-
- if (end < start_addr)
- continue;
-
- /*
- * Since "last" is at most 4GB, we know we'll
- * fit in 32 bits if this condition is true
- */
- if (last > end) {
- unsigned long gap = last - end;
-
- if (gap >= *gapsize) {
- *gapsize = gap;
- *gapstart = end;
- found = 1;
- }
- }
- if (start < last)
- last = start;
- }
- return found;
-}
-
-/*
* Search for the biggest gap in the low 32 bits of the e820
* memory space. We pass this space to PCI to assign MMIO resources
* for hotplug or unconfigured devices in.
@@ -648,6 +57,15 @@ __init void e820_setup_gap(void)
pci_mem_start, gapstart, gapsize);
}
+u64 __init get_max_mapped(void)
+{
+ u64 end = max_pfn_mapped;
+
+ end <<= PAGE_SHIFT;
+
+ return end;
+}
+
/**
* Because of the size limitation of struct boot_params, only first
* 128 E820 memory entries are passed to kernel via
@@ -673,483 +91,22 @@ void __init parse_e820_ext(struct setup_
e820_print_map("extended");
}
-#if defined(CONFIG_X86_64) || \
- (defined(CONFIG_X86_32) && defined(CONFIG_HIBERNATION))
-/**
- * Find the ranges of physical addresses that do not correspond to
- * e820 RAM areas and mark the corresponding pages as nosave for
- * hibernation (32 bit) or software suspend and suspend to RAM (64 bit).
- *
- * This function requires the e820 map to be sorted and without any
- * overlapping entries and assumes the first e820 area to be RAM.
- */
-void __init e820_mark_nosave_regions(unsigned long limit_pfn)
-{
- int i;
- unsigned long pfn;
-
- pfn = PFN_DOWN(e820.map[0].addr + e820.map[0].size);
- for (i = 1; i < e820.nr_map; i++) {
- struct e820entry *ei = &e820.map[i];
-
- if (pfn < PFN_UP(ei->addr))
- register_nosave_region(pfn, PFN_UP(ei->addr));
-
- pfn = PFN_DOWN(ei->addr + ei->size);
- if (ei->type != E820_RAM && ei->type != E820_RESERVED_KERN)
- register_nosave_region(PFN_UP(ei->addr), pfn);
-
- if (pfn >= limit_pfn)
- break;
- }
-}
-#endif
-
-#ifdef CONFIG_HIBERNATION
-/**
- * Mark ACPI NVS memory region, so that we can save/restore it during
- * hibernation and the subsequent resume.
- */
-static int __init e820_mark_nvs_memory(void)
-{
- int i;
-
- for (i = 0; i < e820.nr_map; i++) {
- struct e820entry *ei = &e820.map[i];
-
- if (ei->type == E820_NVS)
- hibernate_nvs_register(ei->addr, ei->size);
- }
-
- return 0;
-}
-core_initcall(e820_mark_nvs_memory);
-#endif
-
-/*
- * Find a free area with specified alignment in a specific range.
- */
-u64 __init find_e820_area(u64 start, u64 end, u64 size, u64 align)
-{
- int i;
-
- for (i = 0; i < e820.nr_map; i++) {
- struct e820entry *ei = &e820.map[i];
- u64 addr;
- u64 ei_start, ei_last;
-
- if (ei->type != E820_RAM)
- continue;
-
- ei_last = ei->addr + ei->size;
- ei_start = ei->addr;
- addr = find_early_area(ei_start, ei_last, start, end,
- size, align);
-
- if (addr != -1ULL)
- return addr;
- }
- return -1ULL;
-}
-
-u64 __init find_fw_memmap_area(u64 start, u64 end, u64 size, u64 align)
-{
- return find_e820_area(start, end, size, align);
-}
-
-u64 __init get_max_mapped(void)
-{
- u64 end = max_pfn_mapped;
-
- end <<= PAGE_SHIFT;
-
- return end;
-}
-/*
- * Find next free range after *start
- */
-u64 __init find_e820_area_size(u64 start, u64 *sizep, u64 align)
-{
- int i;
-
- for (i = 0; i < e820.nr_map; i++) {
- struct e820entry *ei = &e820.map[i];
- u64 addr;
- u64 ei_start, ei_last;
-
- if (ei->type != E820_RAM)
- continue;
-
- ei_last = ei->addr + ei->size;
- ei_start = ei->addr;
- addr = find_early_area_size(ei_start, ei_last, start,
- sizep, align);
-
- if (addr != -1ULL)
- return addr;
- }
-
- return -1ULL;
-}
-
-/*
- * pre allocated 4k and reserved it in e820
- */
-u64 __init early_reserve_e820(u64 startt, u64 sizet, u64 align)
-{
- u64 size = 0;
- u64 addr;
- u64 start;
-
- for (start = startt; ; start += size) {
- start = find_e820_area_size(start, &size, align);
- if (!(start + 1))
- return 0;
- if (size >= sizet)
- break;
- }
-
-#ifdef CONFIG_X86_32
- if (start >= MAXMEM)
- return 0;
- if (start + size > MAXMEM)
- size = MAXMEM - start;
-#endif
-
- addr = round_down(start + size - sizet, align);
- if (addr < start)
- return 0;
- e820_update_range(addr, sizet, E820_RAM, E820_RESERVED);
- e820_update_range_saved(addr, sizet, E820_RAM, E820_RESERVED);
- printk(KERN_INFO "update e820 for early_reserve_e820\n");
- update_e820();
- update_e820_saved();
-
- return addr;
-}
-
-#ifdef CONFIG_X86_32
-# ifdef CONFIG_X86_PAE
-# define MAX_ARCH_PFN (1ULL<<(36-PAGE_SHIFT))
-# else
-# define MAX_ARCH_PFN (1ULL<<(32-PAGE_SHIFT))
-# endif
-#else /* CONFIG_X86_32 */
-# define MAX_ARCH_PFN MAXMEM>>PAGE_SHIFT
-#endif
-
-/*
- * Find the highest page frame number we have available
- */
-static unsigned long __init e820_end_pfn(unsigned long limit_pfn, unsigned type)
-{
- int i;
- unsigned long last_pfn = 0;
- unsigned long max_arch_pfn = MAX_ARCH_PFN;
-
- for (i = 0; i < e820.nr_map; i++) {
- struct e820entry *ei = &e820.map[i];
- unsigned long start_pfn;
- unsigned long end_pfn;
-
- if (ei->type != type)
- continue;
-
- start_pfn = ei->addr >> PAGE_SHIFT;
- end_pfn = (ei->addr + ei->size) >> PAGE_SHIFT;
-
- if (start_pfn >= limit_pfn)
- continue;
- if (end_pfn > limit_pfn) {
- last_pfn = limit_pfn;
- break;
- }
- if (end_pfn > last_pfn)
- last_pfn = end_pfn;
- }
-
- if (last_pfn > max_arch_pfn)
- last_pfn = max_arch_pfn;
-
- printk(KERN_INFO "last_pfn = %#lx max_arch_pfn = %#lx\n",
- last_pfn, max_arch_pfn);
- return last_pfn;
-}
-unsigned long __init e820_end_of_ram_pfn(void)
-{
- return e820_end_pfn(MAX_ARCH_PFN, E820_RAM);
-}
-
-unsigned long __init e820_end_of_low_ram_pfn(void)
-{
- return e820_end_pfn(1UL<<(32 - PAGE_SHIFT), E820_RAM);
-}
/*
- * Finds an active region in the address range from start_pfn to last_pfn and
- * returns its range in ei_startpfn and ei_endpfn for the e820 entry.
- */
-int __init e820_find_active_region(const struct e820entry *ei,
- unsigned long start_pfn,
- unsigned long last_pfn,
- unsigned long *ei_startpfn,
- unsigned long *ei_endpfn)
-{
- u64 align = PAGE_SIZE;
-
- *ei_startpfn = round_up(ei->addr, align) >> PAGE_SHIFT;
- *ei_endpfn = round_down(ei->addr + ei->size, align) >> PAGE_SHIFT;
-
- /* Skip map entries smaller than a page */
- if (*ei_startpfn >= *ei_endpfn)
- return 0;
-
- /* Skip if map is outside the node */
- if (ei->type != E820_RAM || *ei_endpfn <= start_pfn ||
- *ei_startpfn >= last_pfn)
- return 0;
-
- /* Check for overlaps */
- if (*ei_startpfn < start_pfn)
- *ei_startpfn = start_pfn;
- if (*ei_endpfn > last_pfn)
- *ei_endpfn = last_pfn;
-
- return 1;
-}
-
-/* Walk the e820 map and register active regions within a node */
-void __init e820_register_active_regions(int nid, unsigned long start_pfn,
- unsigned long last_pfn)
-{
- unsigned long ei_startpfn;
- unsigned long ei_endpfn;
- int i;
-
- for (i = 0; i < e820.nr_map; i++)
- if (e820_find_active_region(&e820.map[i],
- start_pfn, last_pfn,
- &ei_startpfn, &ei_endpfn))
- add_active_range(nid, ei_startpfn, ei_endpfn);
-}
-
-/*
- * Find the hole size (in bytes) in the memory range.
- * @start: starting address of the memory range to scan
- * @end: ending address of the memory range to scan
- */
-u64 __init e820_hole_size(u64 start, u64 end)
-{
- unsigned long start_pfn = start >> PAGE_SHIFT;
- unsigned long last_pfn = end >> PAGE_SHIFT;
- unsigned long ei_startpfn, ei_endpfn, ram = 0;
- int i;
-
- for (i = 0; i < e820.nr_map; i++) {
- if (e820_find_active_region(&e820.map[i],
- start_pfn, last_pfn,
- &ei_startpfn, &ei_endpfn))
- ram += ei_endpfn - ei_startpfn;
- }
- return end - start - ((u64)ram << PAGE_SHIFT);
-}
-
-static void early_panic(char *msg)
-{
- early_printk(msg);
- panic(msg);
-}
-
-static int userdef __initdata;
-
-/* "mem=nopentium" disables the 4MB page tables. */
-static int __init parse_memopt(char *p)
-{
- u64 mem_size;
-
- if (!p)
- return -EINVAL;
-
-#ifdef CONFIG_X86_32
- if (!strcmp(p, "nopentium")) {
- setup_clear_cpu_cap(X86_FEATURE_PSE);
- return 0;
- }
-#endif
-
- userdef = 1;
- mem_size = memparse(p, &p);
- e820_remove_range(mem_size, ULLONG_MAX - mem_size, E820_RAM, 1);
-
- return 0;
-}
-early_param("mem", parse_memopt);
-
-static int __init parse_memmap_opt(char *p)
-{
- char *oldp;
- u64 start_at, mem_size;
-
- if (!p)
- return -EINVAL;
-
- if (!strncmp(p, "exactmap", 8)) {
-#ifdef CONFIG_CRASH_DUMP
- /*
- * If we are doing a crash dump, we still need to know
- * the real mem size before original memory map is
- * reset.
- */
- saved_max_pfn = e820_end_of_ram_pfn();
-#endif
- e820.nr_map = 0;
- userdef = 1;
- return 0;
- }
-
- oldp = p;
- mem_size = memparse(p, &p);
- if (p == oldp)
- return -EINVAL;
-
- userdef = 1;
- if (*p == '@') {
- start_at = memparse(p+1, &p);
- e820_add_region(start_at, mem_size, E820_RAM);
- } else if (*p == '#') {
- start_at = memparse(p+1, &p);
- e820_add_region(start_at, mem_size, E820_ACPI);
- } else if (*p == '$') {
- start_at = memparse(p+1, &p);
- e820_add_region(start_at, mem_size, E820_RESERVED);
- } else
- e820_remove_range(mem_size, ULLONG_MAX - mem_size, E820_RAM, 1);
-
- return *p == '\0' ? 0 : -EINVAL;
-}
-early_param("memmap", parse_memmap_opt);
-
-void __init finish_e820_parsing(void)
-{
- if (userdef) {
- u32 nr = e820.nr_map;
-
- if (__sanitize_e820_map(e820.map, ARRAY_SIZE(e820.map), &nr) < 0)
- early_panic("Invalid user supplied memory map");
- e820.nr_map = nr;
-
- printk(KERN_INFO "user-defined physical RAM map:\n");
- e820_print_map("user");
- }
-}
-
-static inline const char *e820_type_to_string(int e820_type)
-{
- switch (e820_type) {
- case E820_RESERVED_KERN:
- case E820_RAM: return "System RAM";
- case E820_ACPI: return "ACPI Tables";
- case E820_NVS: return "ACPI Non-volatile Storage";
- case E820_UNUSABLE: return "Unusable memory";
- default: return "reserved";
- }
-}
-
-/*
- * Mark e820 reserved areas as busy for the resource manager.
+ * Copy the BIOS e820 map into a safe place.
+ *
+ * Sanity-check it while we're at it..
+ *
+ * If we're lucky and live on a modern system, the setup code
+ * will have given us a memory map that we can use to properly
+ * set up memory. If we aren't, we'll fake a memory map.
*/
-static struct resource __initdata *e820_res;
-void __init e820_reserve_resources(void)
-{
- int i;
- struct resource *res;
- u64 end;
-
- res = alloc_bootmem(sizeof(struct resource) * e820.nr_map);
- e820_res = res;
- for (i = 0; i < e820.nr_map; i++) {
- end = e820.map[i].addr + e820.map[i].size - 1;
- if (end != (resource_size_t)end) {
- res++;
- continue;
- }
- res->name = e820_type_to_string(e820.map[i].type);
- res->start = e820.map[i].addr;
- res->end = end;
-
- res->flags = IORESOURCE_MEM;
-
- /*
- * don't register the region that could be conflicted with
- * pci device BAR resource and insert them later in
- * pcibios_resource_survey()
- */
- if (e820.map[i].type != E820_RESERVED || res->start < (1ULL<<20)) {
- res->flags |= IORESOURCE_BUSY;
- insert_resource(&iomem_resource, res);
- }
- res++;
- }
-
- for (i = 0; i < e820_saved.nr_map; i++) {
- struct e820entry *entry = &e820_saved.map[i];
- firmware_map_add_early(entry->addr,
- entry->addr + entry->size - 1,
- e820_type_to_string(entry->type));
- }
-}
-
-/* How much should we pad RAM ending depending on where it is? */
-static unsigned long ram_alignment(resource_size_t pos)
-{
- unsigned long mb = pos >> 20;
-
- /* To 64kB in the first megabyte */
- if (!mb)
- return 64*1024;
-
- /* To 1MB in the first 16MB */
- if (mb < 16)
- return 1024*1024;
-
- /* To 64MB for anything above that */
- return 64*1024*1024;
-}
-
-#define MAX_RESOURCE_SIZE ((resource_size_t)-1)
-
-void __init e820_reserve_resources_late(void)
+static int __init append_e820_map(struct e820entry *biosmap, int nr_map)
{
- int i;
- struct resource *res;
-
- res = e820_res;
- for (i = 0; i < e820.nr_map; i++) {
- if (!res->parent && res->end)
- insert_resource_expand_to_fit(&iomem_resource, res);
- res++;
- }
+ /* Only one memory region (or negative)? Ignore it */
+ if (nr_map < 2)
+ return -1;
- /*
- * Try to bump up RAM regions to reasonable boundaries to
- * avoid stolen RAM:
- */
- for (i = 0; i < e820.nr_map; i++) {
- struct e820entry *entry = &e820.map[i];
- u64 start, end;
-
- if (entry->type != E820_RAM)
- continue;
- start = entry->addr + entry->size;
- end = round_up(start, ram_alignment(start)) - 1;
- if (end > MAX_RESOURCE_SIZE)
- end = MAX_RESOURCE_SIZE;
- if (start >= end)
- continue;
- printk(KERN_DEBUG "reserve RAM buffer: %016llx - %016llx ",
- start, end);
- reserve_region_with_split(&iomem_resource, start, end,
- "RAM buffer");
- }
+ return __append_e820_map(biosmap, nr_map);
}
char *__init default_machine_specific_memory_setup(void)
@@ -1181,7 +138,7 @@ char *__init default_machine_specific_me
who = "BIOS-e801";
}
- e820.nr_map = 0;
+ clear_e820_map();
e820_add_region(0, LOWMEMSIZE(), E820_RAM);
e820_add_region(HIGH_MEMORY, mem_size << 10, E820_RAM);
}
@@ -1190,11 +147,6 @@ char *__init default_machine_specific_me
return who;
}
-void __init save_e820_map(void)
-{
- memcpy(&e820_saved, &e820, sizeof(struct e820map));
-}
-
void __init setup_memory_map(void)
{
char *who;
@@ -1206,58 +158,12 @@ void __init setup_memory_map(void)
}
#ifdef CONFIG_X86_OOSTORE
-/*
- * Figure what we can cover with MCR's
- *
- * Shortcut: We know you can't put 4Gig of RAM on a winchip
- */
+int centaur_ram_top;
void __init get_centaur_ram_top(void)
{
- u32 clip = 0xFFFFFFFFUL;
- u32 top = 0;
- int i;
-
if (boot_cpu_data.x86_vendor != X86_VENDOR_CENTAUR)
return;
- for (i = 0; i < e820.nr_map; i++) {
- unsigned long start, end;
-
- if (e820.map[i].addr > 0xFFFFFFFFUL)
- continue;
- /*
- * Don't MCR over reserved space. Ignore the ISA hole
- * we frob around that catastrophe already
- */
- if (e820.map[i].type == E820_RESERVED) {
- if (e820.map[i].addr >= 0x100000UL &&
- e820.map[i].addr < clip)
- clip = e820.map[i].addr;
- continue;
- }
- start = e820.map[i].addr;
- end = e820.map[i].addr + e820.map[i].size;
- if (start >= end)
- continue;
- if (end > top)
- top = end;
- }
- /*
- * Everything below 'top' should be RAM except for the ISA hole.
- * Because of the limited MCR's we want to map NV/ACPI into our
- * MCR range for gunk in RAM
- *
- * Clip might cause us to MCR insufficient RAM but that is an
- * acceptable failure mode and should only bite obscure boxes with
- * a VESA hole at 15Mb
- *
- * The second case Clip sometimes kicks in is when the EBDA is marked
- * as reserved. Again we fail safe with reasonable results
- */
- if (top > clip)
- top = clip;
-
- centaur_ram_top = top;
+ centaur_ram_top = __get_special_low_ram_top();
}
#endif
-
Index: linux-2.6/kernel/fw_memmap.c
===================================================================
--- /dev/null
+++ linux-2.6/kernel/fw_memmap.c
@@ -0,0 +1,1134 @@
+/*
+ * Handle the memory map.
+ * The functions here do the job until bootmem takes over.
+ *
+ * Getting sanitize_e820_map() in sync with i386 version by applying change:
+ * - Provisions for empty E820 memory regions (reported by certain BIOSes).
+ * Alex Achenbach <xela@xxxxxxx>, December 2002.
+ * Venkatesh Pallipadi <venkatesh.pallipadi@xxxxxxxxx>
+ *
+ */
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/bootmem.h>
+#include <linux/suspend.h>
+#include <linux/firmware-map.h>
+#include <linux/fw_memmap.h>
+#include <linux/ioport.h>
+
+/*
+ * The e820 map is the map that gets modified e.g. with command line parameters
+ * and that is also registered with modifications in the kernel resource tree
+ * with the iomem_resource as parent.
+ *
+ * The e820_saved is directly saved after the BIOS-provided memory map is
+ * copied. It doesn't get modified afterwards. It's registered for the
+ * /sys/firmware/memmap interface.
+ *
+ * That memory map is not modified and is used as base for kexec. The kexec'd
+ * kernel should get the same memory map as the firmware provides. Then the
+ * user can e.g. boot the original kernel with mem=1G while still booting the
+ * next kernel with full memory.
+ */
+static struct e820map __initdata e820;
+static struct e820map __initdata e820_saved;
+
+/*
+ * This function checks if any part of the range <start,end> is mapped
+ * with type.
+ * phys_pud_init() is using it and is _meminit, but we have !after_bootmem
+ * so could use refok here
+ */
+int __init_refok e820_any_mapped(u64 start, u64 end, unsigned type)
+{
+ int i;
+
+ for (i = 0; i < e820.nr_map; i++) {
+ struct e820entry *ei = &e820.map[i];
+
+ if (type && ei->type != type)
+ continue;
+ if (ei->addr >= end || ei->addr + ei->size <= start)
+ continue;
+ return 1;
+ }
+ return 0;
+}
+
+/*
+ * This function checks if the entire range <start,end> is mapped with type.
+ *
+ * Note: this function only works correct if the e820 table is sorted and
+ * not-overlapping, which is the case
+ */
+int __init e820_all_mapped(u64 start, u64 end, unsigned type)
+{
+ int i;
+
+ for (i = 0; i < e820.nr_map; i++) {
+ struct e820entry *ei = &e820.map[i];
+
+ if (type && ei->type != type)
+ continue;
+ /* is the region (part) in overlap with the current region ?*/
+ if (ei->addr >= end || ei->addr + ei->size <= start)
+ continue;
+
+ /* if the region is at the beginning of <start,end> we move
+ * start to the end of the region since it's ok until there
+ */
+ if (ei->addr <= start)
+ start = ei->addr + ei->size;
+ /*
+ * if start is now at or beyond end, we're done, full
+ * coverage
+ */
+ if (start >= end)
+ return 1;
+ }
+ return 0;
+}
+
+/*
+ * Add a memory region to the kernel e820 map.
+ */
+static void __init __e820_add_region(struct e820map *e820x, u64 start, u64 size,
+ int type)
+{
+ int x = e820x->nr_map;
+
+ if (x >= ARRAY_SIZE(e820x->map)) {
+ printk(KERN_ERR "Ooops! Too many entries in the memory map!\n");
+ return;
+ }
+
+ e820x->map[x].addr = start;
+ e820x->map[x].size = size;
+ e820x->map[x].type = type;
+ e820x->nr_map++;
+}
+
+void __init e820_add_region(u64 start, u64 size, int type)
+{
+ __e820_add_region(&e820, start, size, type);
+}
+
+static void __init e820_print_type(u32 type)
+{
+ switch (type) {
+ case E820_RAM:
+ case E820_RESERVED_KERN:
+ printk(KERN_CONT "(usable)");
+ break;
+ case E820_RESERVED:
+ printk(KERN_CONT "(reserved)");
+ break;
+ case E820_ACPI:
+ printk(KERN_CONT "(ACPI data)");
+ break;
+ case E820_NVS:
+ printk(KERN_CONT "(ACPI NVS)");
+ break;
+ case E820_UNUSABLE:
+ printk(KERN_CONT "(unusable)");
+ break;
+ default:
+ printk(KERN_CONT "type %u", type);
+ break;
+ }
+}
+
+void __init e820_print_map(char *who)
+{
+ int i;
+
+ for (i = 0; i < e820.nr_map; i++) {
+ printk(KERN_INFO " %s: %016Lx - %016Lx ", who,
+ (unsigned long long) e820.map[i].addr,
+ (unsigned long long)
+ (e820.map[i].addr + e820.map[i].size));
+ e820_print_type(e820.map[i].type);
+ printk(KERN_CONT "\n");
+ }
+}
+
+/*
+ * Sanitize the BIOS e820 map.
+ *
+ * Some e820 responses include overlapping entries. The following
+ * replaces the original e820 map with a new one, removing overlaps,
+ * and resolving conflicting memory types in favor of highest
+ * numbered type.
+ *
+ * The input parameter biosmap points to an array of 'struct
+ * e820entry' which on entry has elements in the range [0, *pnr_map)
+ * valid, and which has space for up to max_nr_map entries.
+ * On return, the resulting sanitized e820 map entries will be in
+ * overwritten in the same location, starting at biosmap.
+ *
+ * The integer pointed to by pnr_map must be valid on entry (the
+ * current number of valid entries located at biosmap) and will
+ * be updated on return, with the new number of valid entries
+ * (something no more than max_nr_map.)
+ *
+ * The return value from sanitize_e820_map() is zero if it
+ * successfully 'sanitized' the map entries passed in, and is -1
+ * if it did nothing, which can happen if either of (1) it was
+ * only passed one map entry, or (2) any of the input map entries
+ * were invalid (start + size < start, meaning that the size was
+ * so big the described memory range wrapped around through zero.)
+ *
+ * Visually we're performing the following
+ * (1,2,3,4 = memory types)...
+ *
+ * Sample memory map (w/overlaps):
+ * ____22__________________
+ * ______________________4_
+ * ____1111________________
+ * _44_____________________
+ * 11111111________________
+ * ____________________33__
+ * ___________44___________
+ * __________33333_________
+ * ______________22________
+ * ___________________2222_
+ * _________111111111______
+ * _____________________11_
+ * _________________4______
+ *
+ * Sanitized equivalent (no overlap):
+ * 1_______________________
+ * _44_____________________
+ * ___1____________________
+ * ____22__________________
+ * ______11________________
+ * _________1______________
+ * __________3_____________
+ * ___________44___________
+ * _____________33_________
+ * _______________2________
+ * ________________1_______
+ * _________________4______
+ * ___________________2____
+ * ____________________33__
+ * ______________________4_
+ */
+
+int __init __sanitize_e820_map(struct e820entry *biosmap, int max_nr_map,
+ u32 *pnr_map)
+{
+ struct change_member {
+ struct e820entry *pbios; /* pointer to original bios entry */
+ unsigned long long addr; /* address for this change point */
+ };
+ static struct change_member change_point_list[2*E820_X_MAX] __initdata;
+ static struct change_member *change_point[2*E820_X_MAX] __initdata;
+ static struct e820entry *overlap_list[E820_X_MAX] __initdata;
+ static struct e820entry new_bios[E820_X_MAX] __initdata;
+ struct change_member *change_tmp;
+ unsigned long current_type, last_type;
+ unsigned long long last_addr;
+ int chgidx, still_changing;
+ int overlap_entries;
+ int new_bios_entry;
+ int old_nr, new_nr, chg_nr;
+ int i;
+
+ /* if there's only one memory region, don't bother */
+ if (*pnr_map < 2)
+ return -1;
+
+ old_nr = *pnr_map;
+ BUG_ON(old_nr > max_nr_map);
+
+ /* bail out if we find any unreasonable addresses in bios map */
+ for (i = 0; i < old_nr; i++)
+ if (biosmap[i].addr + biosmap[i].size < biosmap[i].addr)
+ return -1;
+
+ /* create pointers for initial change-point information (for sorting) */
+ for (i = 0; i < 2 * old_nr; i++)
+ change_point[i] = &change_point_list[i];
+
+ /* record all known change-points (starting and ending addresses),
+ omitting those that are for empty memory regions */
+ chgidx = 0;
+ for (i = 0; i < old_nr; i++) {
+ if (biosmap[i].size != 0) {
+ change_point[chgidx]->addr = biosmap[i].addr;
+ change_point[chgidx++]->pbios = &biosmap[i];
+ change_point[chgidx]->addr = biosmap[i].addr +
+ biosmap[i].size;
+ change_point[chgidx++]->pbios = &biosmap[i];
+ }
+ }
+ chg_nr = chgidx;
+
+ /* sort change-point list by memory addresses (low -> high) */
+ still_changing = 1;
+ while (still_changing) {
+ still_changing = 0;
+ for (i = 1; i < chg_nr; i++) {
+ unsigned long long curaddr, lastaddr;
+ unsigned long long curpbaddr, lastpbaddr;
+
+ curaddr = change_point[i]->addr;
+ lastaddr = change_point[i - 1]->addr;
+ curpbaddr = change_point[i]->pbios->addr;
+ lastpbaddr = change_point[i - 1]->pbios->addr;
+
+ /*
+ * swap entries, when:
+ *
+ * curaddr > lastaddr or
+ * curaddr == lastaddr and curaddr == curpbaddr and
+ * lastaddr != lastpbaddr
+ */
+ if (curaddr < lastaddr ||
+ (curaddr == lastaddr && curaddr == curpbaddr &&
+ lastaddr != lastpbaddr)) {
+ change_tmp = change_point[i];
+ change_point[i] = change_point[i-1];
+ change_point[i-1] = change_tmp;
+ still_changing = 1;
+ }
+ }
+ }
+
+ /* create a new bios memory map, removing overlaps */
+ overlap_entries = 0; /* number of entries in the overlap table */
+ new_bios_entry = 0; /* index for creating new bios map entries */
+ last_type = 0; /* start with undefined memory type */
+ last_addr = 0; /* start with 0 as last starting address */
+
+ /* loop through change-points, determining affect on the new bios map */
+ for (chgidx = 0; chgidx < chg_nr; chgidx++) {
+ /* keep track of all overlapping bios entries */
+ if (change_point[chgidx]->addr ==
+ change_point[chgidx]->pbios->addr) {
+ /*
+ * add map entry to overlap list (> 1 entry
+ * implies an overlap)
+ */
+ overlap_list[overlap_entries++] =
+ change_point[chgidx]->pbios;
+ } else {
+ /*
+ * remove entry from list (order independent,
+ * so swap with last)
+ */
+ for (i = 0; i < overlap_entries; i++) {
+ if (overlap_list[i] ==
+ change_point[chgidx]->pbios)
+ overlap_list[i] =
+ overlap_list[overlap_entries-1];
+ }
+ overlap_entries--;
+ }
+ /*
+ * if there are overlapping entries, decide which
+ * "type" to use (larger value takes precedence --
+ * 1=usable, 2,3,4,4+=unusable)
+ */
+ current_type = 0;
+ for (i = 0; i < overlap_entries; i++)
+ if (overlap_list[i]->type > current_type)
+ current_type = overlap_list[i]->type;
+ /*
+ * continue building up new bios map based on this
+ * information
+ */
+ if (current_type != last_type) {
+ if (last_type != 0) {
+ new_bios[new_bios_entry].size =
+ change_point[chgidx]->addr - last_addr;
+ /*
+ * move forward only if the new size
+ * was non-zero
+ */
+ if (new_bios[new_bios_entry].size != 0)
+ /*
+ * no more space left for new
+ * bios entries ?
+ */
+ if (++new_bios_entry >= max_nr_map)
+ break;
+ }
+ if (current_type != 0) {
+ new_bios[new_bios_entry].addr =
+ change_point[chgidx]->addr;
+ new_bios[new_bios_entry].type = current_type;
+ last_addr = change_point[chgidx]->addr;
+ }
+ last_type = current_type;
+ }
+ }
+ /* retain count for new bios entries */
+ new_nr = new_bios_entry;
+
+ /* copy new bios mapping into original location */
+ memcpy(biosmap, new_bios, new_nr * sizeof(struct e820entry));
+ *pnr_map = new_nr;
+
+ return 0;
+}
+
+int __init sanitize_e820_map(void)
+{
+ int max_nr_map = ARRAY_SIZE(e820.map);
+
+ return __sanitize_e820_map(e820.map, max_nr_map, &e820.nr_map);
+}
+
+int __init __append_e820_map(struct e820entry *biosmap, int nr_map)
+{
+ while (nr_map) {
+ u64 start = biosmap->addr;
+ u64 size = biosmap->size;
+ u64 end = start + size;
+ u32 type = biosmap->type;
+
+ /* Overflow in 64 bits? Ignore the memory map. */
+ if (start > end)
+ return -1;
+
+ e820_add_region(start, size, type);
+
+ biosmap++;
+ nr_map--;
+ }
+ return 0;
+}
+
+void __init clear_e820_map(void)
+{
+ e820.nr_map = 0;
+}
+
+static u64 __init __e820_update_range(struct e820map *e820x, u64 start,
+ u64 size, unsigned old_type,
+ unsigned new_type)
+{
+ u64 end;
+ unsigned int i;
+ u64 real_updated_size = 0;
+
+ BUG_ON(old_type == new_type);
+
+ if (size > (ULLONG_MAX - start))
+ size = ULLONG_MAX - start;
+
+ end = start + size;
+ printk(KERN_DEBUG "e820 update range: %016Lx - %016Lx ",
+ (unsigned long long) start,
+ (unsigned long long) end);
+ e820_print_type(old_type);
+ printk(KERN_CONT " ==> ");
+ e820_print_type(new_type);
+ printk(KERN_CONT "\n");
+
+ for (i = 0; i < e820x->nr_map; i++) {
+ struct e820entry *ei = &e820x->map[i];
+ u64 final_start, final_end;
+ u64 ei_end;
+
+ if (ei->type != old_type)
+ continue;
+
+ ei_end = ei->addr + ei->size;
+ /* totally covered by new range? */
+ if (ei->addr >= start && ei_end <= end) {
+ ei->type = new_type;
+ real_updated_size += ei->size;
+ continue;
+ }
+
+ /* new range is totally covered? */
+ if (ei->addr < start && ei_end > end) {
+ __e820_add_region(e820x, start, size, new_type);
+ __e820_add_region(e820x, end, ei_end - end, ei->type);
+ ei->size = start - ei->addr;
+ real_updated_size += size;
+ continue;
+ }
+
+ /* partially covered */
+ final_start = max(start, ei->addr);
+ final_end = min(end, ei_end);
+ if (final_start >= final_end)
+ continue;
+
+ __e820_add_region(e820x, final_start, final_end - final_start,
+ new_type);
+
+ real_updated_size += final_end - final_start;
+
+ /*
+ * left range could be head or tail, so need to update
+ * size at first.
+ */
+ ei->size -= final_end - final_start;
+ if (ei->addr < final_start)
+ continue;
+ ei->addr = final_end;
+ }
+ return real_updated_size;
+}
+
+u64 __init e820_update_range(u64 start, u64 size, unsigned old_type,
+ unsigned new_type)
+{
+ return __e820_update_range(&e820, start, size, old_type, new_type);
+}
+
+static u64 __init e820_update_range_saved(u64 start, u64 size,
+ unsigned old_type, unsigned new_type)
+{
+ return __e820_update_range(&e820_saved, start, size, old_type,
+ new_type);
+}
+
+/* make e820 not cover the range */
+u64 __init e820_remove_range(u64 start, u64 size, unsigned old_type,
+ int checktype)
+{
+ int i;
+ u64 end;
+ u64 real_removed_size = 0;
+
+ if (size > (ULLONG_MAX - start))
+ size = ULLONG_MAX - start;
+
+ end = start + size;
+ printk(KERN_DEBUG "e820 remove range: %016Lx - %016Lx ",
+ (unsigned long long) start,
+ (unsigned long long) end);
+ e820_print_type(old_type);
+ printk(KERN_CONT "\n");
+
+ for (i = 0; i < e820.nr_map; i++) {
+ struct e820entry *ei = &e820.map[i];
+ u64 final_start, final_end;
+
+ if (checktype && ei->type != old_type)
+ continue;
+ /* totally covered? */
+ if (ei->addr >= start &&
+ (ei->addr + ei->size) <= (start + size)) {
+ real_removed_size += ei->size;
+ memset(ei, 0, sizeof(struct e820entry));
+ continue;
+ }
+ /* partially covered */
+ final_start = max(start, ei->addr);
+ final_end = min(start + size, ei->addr + ei->size);
+ if (final_start >= final_end)
+ continue;
+ real_removed_size += final_end - final_start;
+
+ ei->size -= final_end - final_start;
+ if (ei->addr < final_start)
+ continue;
+ ei->addr = final_end;
+ }
+ return real_removed_size;
+}
+
+void __init update_e820(void)
+{
+ u32 nr_map;
+
+ nr_map = e820.nr_map;
+ if (__sanitize_e820_map(e820.map, ARRAY_SIZE(e820.map), &nr_map))
+ return;
+ e820.nr_map = nr_map;
+ printk(KERN_INFO "modified physical RAM map:\n");
+ e820_print_map("modified");
+}
+
+static void __init update_e820_saved(void)
+{
+ u32 nr_map;
+ int max_nr_map = ARRAY_SIZE(e820_saved.map);
+
+ nr_map = e820_saved.nr_map;
+ if (__sanitize_e820_map(e820_saved.map, max_nr_map, &nr_map))
+ return;
+ e820_saved.nr_map = nr_map;
+}
+
+/*
+ * Search for a gap in the e820 memory space from start_addr to end_addr.
+ */
+__init int e820_search_gap(unsigned long *gapstart, unsigned long *gapsize,
+ unsigned long start_addr, unsigned long long end_addr)
+{
+ unsigned long long last;
+ int i = e820.nr_map;
+ int found = 0;
+
+ last = (end_addr && end_addr < MAX_GAP_END) ? end_addr : MAX_GAP_END;
+
+ while (--i >= 0) {
+ unsigned long long start = e820.map[i].addr;
+ unsigned long long end = start + e820.map[i].size;
+
+ if (end < start_addr)
+ continue;
+
+ /*
+ * Since "last" is at most 4GB, we know we'll
+ * fit in 32 bits if this condition is true
+ */
+ if (last > end) {
+ unsigned long gap = last - end;
+
+ if (gap >= *gapsize) {
+ *gapsize = gap;
+ *gapstart = end;
+ found = 1;
+ }
+ }
+ if (start < last)
+ last = start;
+ }
+ return found;
+}
+
+#if defined(CONFIG_X86_64) || \
+ (defined(CONFIG_X86_32) && defined(CONFIG_HIBERNATION))
+/**
+ * Find the ranges of physical addresses that do not correspond to
+ * e820 RAM areas and mark the corresponding pages as nosave for
+ * hibernation (32 bit) or software suspend and suspend to RAM (64 bit).
+ *
+ * This function requires the e820 map to be sorted and without any
+ * overlapping entries and assumes the first e820 area to be RAM.
+ */
+void __init e820_mark_nosave_regions(unsigned long limit_pfn)
+{
+ int i;
+ unsigned long pfn;
+
+ pfn = PFN_DOWN(e820.map[0].addr + e820.map[0].size);
+ for (i = 1; i < e820.nr_map; i++) {
+ struct e820entry *ei = &e820.map[i];
+
+ if (pfn < PFN_UP(ei->addr))
+ register_nosave_region(pfn, PFN_UP(ei->addr));
+
+ pfn = PFN_DOWN(ei->addr + ei->size);
+ if (ei->type != E820_RAM && ei->type != E820_RESERVED_KERN)
+ register_nosave_region(PFN_UP(ei->addr), pfn);
+
+ if (pfn >= limit_pfn)
+ break;
+ }
+}
+#endif
+
+#ifdef CONFIG_HIBERNATION
+/**
+ * Mark ACPI NVS memory region, so that we can save/restore it during
+ * hibernation and the subsequent resume.
+ */
+static int __init e820_mark_nvs_memory(void)
+{
+ int i;
+
+ for (i = 0; i < e820.nr_map; i++) {
+ struct e820entry *ei = &e820.map[i];
+
+ if (ei->type == E820_NVS)
+ hibernate_nvs_register(ei->addr, ei->size);
+ }
+
+ return 0;
+}
+core_initcall(e820_mark_nvs_memory);
+#endif
+
+/*
+ * Find a free area with specified alignment in a specific range.
+ */
+u64 __init find_e820_area(u64 start, u64 end, u64 size, u64 align)
+{
+ int i;
+
+ for (i = 0; i < e820.nr_map; i++) {
+ struct e820entry *ei = &e820.map[i];
+ u64 addr;
+ u64 ei_start, ei_last;
+
+ if (ei->type != E820_RAM)
+ continue;
+
+ ei_last = ei->addr + ei->size;
+ ei_start = ei->addr;
+ addr = find_early_area(ei_start, ei_last, start, end,
+ size, align);
+
+ if (addr != -1ULL)
+ return addr;
+ }
+ return -1ULL;
+}
+
+u64 __init find_fw_memmap_area(u64 start, u64 end, u64 size, u64 align)
+{
+ return find_e820_area(start, end, size, align);
+}
+
+/*
+ * Find next free range after *start
+ */
+u64 __init find_e820_area_size(u64 start, u64 *sizep, u64 align)
+{
+ int i;
+
+ for (i = 0; i < e820.nr_map; i++) {
+ struct e820entry *ei = &e820.map[i];
+ u64 addr;
+ u64 ei_start, ei_last;
+
+ if (ei->type != E820_RAM)
+ continue;
+
+ ei_last = ei->addr + ei->size;
+ ei_start = ei->addr;
+ addr = find_early_area_size(ei_start, ei_last, start,
+ sizep, align);
+
+ if (addr != -1ULL)
+ return addr;
+ }
+
+ return -1ULL;
+}
+
+/*
+ * pre allocated 4k and reserved it in e820
+ */
+u64 __init early_reserve_e820(u64 startt, u64 sizet, u64 align)
+{
+ u64 size = 0;
+ u64 addr;
+ u64 start;
+
+ for (start = startt; ; start += size) {
+ start = find_e820_area_size(start, &size, align);
+ if (!(start + 1))
+ return 0;
+ if (size >= sizet)
+ break;
+ }
+
+#ifdef CONFIG_X86_32
+ if (start >= MAXMEM)
+ return 0;
+ if (start + size > MAXMEM)
+ size = MAXMEM - start;
+#endif
+
+ addr = round_down(start + size - sizet, align);
+ if (addr < start)
+ return 0;
+ e820_update_range(addr, sizet, E820_RAM, E820_RESERVED);
+ e820_update_range_saved(addr, sizet, E820_RAM, E820_RESERVED);
+ printk(KERN_INFO "update e820 for early_reserve_e820\n");
+ update_e820();
+ update_e820_saved();
+
+ return addr;
+}
+
+#ifdef CONFIG_X86_32
+# ifdef CONFIG_X86_PAE
+# define MAX_ARCH_PFN (1ULL<<(36-PAGE_SHIFT))
+# else
+# define MAX_ARCH_PFN (1ULL<<(32-PAGE_SHIFT))
+# endif
+#else /* CONFIG_X86_32 */
+# define MAX_ARCH_PFN (MAXMEM>>PAGE_SHIFT)
+#endif
+
+/*
+ * Find the highest page frame number we have available
+ */
+static unsigned long __init e820_end_pfn(unsigned long limit_pfn, unsigned type)
+{
+ int i;
+ unsigned long last_pfn = 0;
+ unsigned long max_arch_pfn = MAX_ARCH_PFN;
+
+ for (i = 0; i < e820.nr_map; i++) {
+ struct e820entry *ei = &e820.map[i];
+ unsigned long start_pfn;
+ unsigned long end_pfn;
+
+ if (ei->type != type)
+ continue;
+
+ start_pfn = ei->addr >> PAGE_SHIFT;
+ end_pfn = (ei->addr + ei->size) >> PAGE_SHIFT;
+
+ if (start_pfn >= limit_pfn)
+ continue;
+ if (end_pfn > limit_pfn) {
+ last_pfn = limit_pfn;
+ break;
+ }
+ if (end_pfn > last_pfn)
+ last_pfn = end_pfn;
+ }
+
+ if (last_pfn > max_arch_pfn)
+ last_pfn = max_arch_pfn;
+
+ printk(KERN_INFO "last_pfn = %#lx max_arch_pfn = %#lx\n",
+ last_pfn, max_arch_pfn);
+ return last_pfn;
+}
+unsigned long __init e820_end_of_ram_pfn(void)
+{
+ return e820_end_pfn(MAX_ARCH_PFN, E820_RAM);
+}
+
+unsigned long __init e820_end_of_low_ram_pfn(void)
+{
+ return e820_end_pfn(1UL<<(32 - PAGE_SHIFT), E820_RAM);
+}
+/*
+ * Finds an active region in the address range from start_pfn to last_pfn and
+ * returns its range in ei_startpfn and ei_endpfn for the e820 entry.
+ */
+int __init e820_find_active_region(const struct e820entry *ei,
+ unsigned long start_pfn,
+ unsigned long last_pfn,
+ unsigned long *ei_startpfn,
+ unsigned long *ei_endpfn)
+{
+ u64 align = PAGE_SIZE;
+
+ *ei_startpfn = round_up(ei->addr, align) >> PAGE_SHIFT;
+ *ei_endpfn = round_down(ei->addr + ei->size, align) >> PAGE_SHIFT;
+
+ /* Skip map entries smaller than a page */
+ if (*ei_startpfn >= *ei_endpfn)
+ return 0;
+
+ /* Skip if map is outside the node */
+ if (ei->type != E820_RAM || *ei_endpfn <= start_pfn ||
+ *ei_startpfn >= last_pfn)
+ return 0;
+
+ /* Check for overlaps */
+ if (*ei_startpfn < start_pfn)
+ *ei_startpfn = start_pfn;
+ if (*ei_endpfn > last_pfn)
+ *ei_endpfn = last_pfn;
+
+ return 1;
+}
+
+/* Walk the e820 map and register active regions within a node */
+void __init e820_register_active_regions(int nid, unsigned long start_pfn,
+ unsigned long last_pfn)
+{
+ unsigned long ei_startpfn;
+ unsigned long ei_endpfn;
+ int i;
+
+ for (i = 0; i < e820.nr_map; i++)
+ if (e820_find_active_region(&e820.map[i],
+ start_pfn, last_pfn,
+ &ei_startpfn, &ei_endpfn))
+ add_active_range(nid, ei_startpfn, ei_endpfn);
+}
+
+/*
+ * Find the hole size (in bytes) in the memory range.
+ * @start: starting address of the memory range to scan
+ * @end: ending address of the memory range to scan
+ */
+u64 __init e820_hole_size(u64 start, u64 end)
+{
+ unsigned long start_pfn = start >> PAGE_SHIFT;
+ unsigned long last_pfn = end >> PAGE_SHIFT;
+ unsigned long ei_startpfn, ei_endpfn, ram = 0;
+ int i;
+
+ for (i = 0; i < e820.nr_map; i++) {
+ if (e820_find_active_region(&e820.map[i],
+ start_pfn, last_pfn,
+ &ei_startpfn, &ei_endpfn))
+ ram += ei_endpfn - ei_startpfn;
+ }
+ return end - start - ((u64)ram << PAGE_SHIFT);
+}
+
+static void early_panic(char *msg)
+{
+ early_printk(msg);
+ panic(msg);
+}
+
+static int userdef __initdata;
+
+/* "mem=nopentium" disables the 4MB page tables. */
+static int __init parse_memopt(char *p)
+{
+ u64 mem_size;
+
+ if (!p)
+ return -EINVAL;
+
+#ifdef CONFIG_X86_32
+ if (!strcmp(p, "nopentium")) {
+ setup_clear_cpu_cap(X86_FEATURE_PSE);
+ return 0;
+ }
+#endif
+
+ userdef = 1;
+ mem_size = memparse(p, &p);
+ e820_remove_range(mem_size, ULLONG_MAX - mem_size, E820_RAM, 1);
+
+ return 0;
+}
+early_param("mem", parse_memopt);
+
+static int __init parse_memmap_opt(char *p)
+{
+ char *oldp;
+ u64 start_at, mem_size;
+
+ if (!p)
+ return -EINVAL;
+
+ if (!strncmp(p, "exactmap", 8)) {
+#ifdef CONFIG_CRASH_DUMP
+ /*
+ * If we are doing a crash dump, we still need to know
+ * the real mem size before original memory map is
+ * reset.
+ */
+ saved_max_pfn = e820_end_of_ram_pfn();
+#endif
+ e820.nr_map = 0;
+ userdef = 1;
+ return 0;
+ }
+
+ oldp = p;
+ mem_size = memparse(p, &p);
+ if (p == oldp)
+ return -EINVAL;
+
+ userdef = 1;
+ if (*p == '@') {
+ start_at = memparse(p+1, &p);
+ e820_add_region(start_at, mem_size, E820_RAM);
+ } else if (*p == '#') {
+ start_at = memparse(p+1, &p);
+ e820_add_region(start_at, mem_size, E820_ACPI);
+ } else if (*p == '$') {
+ start_at = memparse(p+1, &p);
+ e820_add_region(start_at, mem_size, E820_RESERVED);
+ } else
+ e820_remove_range(mem_size, ULLONG_MAX - mem_size, E820_RAM, 1);
+
+ return *p == '\0' ? 0 : -EINVAL;
+}
+early_param("memmap", parse_memmap_opt);
+
+void __init finish_e820_parsing(void)
+{
+ if (userdef) {
+ u32 nr = e820.nr_map;
+ int max_nr_map = ARRAY_SIZE(e820.map);
+
+ if (__sanitize_e820_map(e820.map, max_nr_map, &nr) < 0)
+ early_panic("Invalid user supplied memory map");
+ e820.nr_map = nr;
+
+ printk(KERN_INFO "user-defined physical RAM map:\n");
+ e820_print_map("user");
+ }
+}
+
+static inline const char *e820_type_to_string(int e820_type)
+{
+ switch (e820_type) {
+ case E820_RESERVED_KERN:
+ case E820_RAM: return "System RAM";
+ case E820_ACPI: return "ACPI Tables";
+ case E820_NVS: return "ACPI Non-volatile Storage";
+ case E820_UNUSABLE: return "Unusable memory";
+ default: return "reserved";
+ }
+}
+
+/*
+ * Mark e820 reserved areas as busy for the resource manager.
+ */
+static struct resource __initdata *e820_res;
+void __init e820_reserve_resources(void)
+{
+ int i;
+ struct resource *res;
+ u64 end;
+
+ res = alloc_bootmem(sizeof(struct resource) * e820.nr_map);
+ e820_res = res;
+ for (i = 0; i < e820.nr_map; i++) {
+ end = e820.map[i].addr + e820.map[i].size - 1;
+ if (end != (resource_size_t)end) {
+ res++;
+ continue;
+ }
+ res->name = e820_type_to_string(e820.map[i].type);
+ res->start = e820.map[i].addr;
+ res->end = end;
+
+ res->flags = IORESOURCE_MEM;
+
+ /*
+ * don't register the region that could be conflicted with
+ * pci device BAR resource and insert them later in
+ * pcibios_resource_survey()
+ */
+ if (e820.map[i].type != E820_RESERVED ||
+ res->start < (1ULL<<20)) {
+ res->flags |= IORESOURCE_BUSY;
+ insert_resource(&iomem_resource, res);
+ }
+ res++;
+ }
+
+ for (i = 0; i < e820_saved.nr_map; i++) {
+ struct e820entry *entry = &e820_saved.map[i];
+ firmware_map_add_early(entry->addr,
+ entry->addr + entry->size - 1,
+ e820_type_to_string(entry->type));
+ }
+}
+
+/* How much should we pad RAM ending depending on where it is? */
+static unsigned long __init ram_alignment(resource_size_t pos)
+{
+ unsigned long mb = pos >> 20;
+
+ /* To 64kB in the first megabyte */
+ if (!mb)
+ return 64*1024;
+
+ /* To 1MB in the first 16MB */
+ if (mb < 16)
+ return 1024*1024;
+
+ /* To 64MB for anything above that */
+ return 64*1024*1024;
+}
+
+#define MAX_RESOURCE_SIZE ((resource_size_t)-1)
+
+void __init e820_reserve_resources_late(void)
+{
+ int i;
+ struct resource *res;
+
+ res = e820_res;
+ for (i = 0; i < e820.nr_map; i++) {
+ if (!res->parent && res->end)
+ insert_resource_expand_to_fit(&iomem_resource, res);
+ res++;
+ }
+
+ /*
+ * Try to bump up RAM regions to reasonable boundaries to
+ * avoid stolen RAM:
+ */
+ for (i = 0; i < e820.nr_map; i++) {
+ struct e820entry *entry = &e820.map[i];
+ u64 start, end;
+
+ if (entry->type != E820_RAM)
+ continue;
+ start = entry->addr + entry->size;
+ end = round_up(start, ram_alignment(start)) - 1;
+ if (end > MAX_RESOURCE_SIZE)
+ end = MAX_RESOURCE_SIZE;
+ if (start >= end)
+ continue;
+ printk(KERN_DEBUG "reserve RAM buffer: %016llx - %016llx ",
+ start, end);
+ reserve_region_with_split(&iomem_resource, start, end,
+ "RAM buffer");
+ }
+}
+
+void __init save_e820_map(void)
+{
+ memcpy(&e820_saved, &e820, sizeof(struct e820map));
+}
+
+#ifdef CONFIG_X86_OOSTORE
+
+/*
+ * this one should stay in arch/x86/kernel/e820.c,
+ * but we want to keep e820 to be static here
+ */
+/*
+ * Figure what we can cover with MCR's
+ *
+ * Shortcut: We know you can't put 4Gig of RAM on a winchip
+ */
+void __init __get_special_low_ram_top(void)
+{
+ u32 clip = 0xFFFFFFFFUL;
+ u32 top = 0;
+ int i;
+
+ for (i = 0; i < e820.nr_map; i++) {
+ unsigned long start, end;
+
+ if (e820.map[i].addr > 0xFFFFFFFFUL)
+ continue;
+ /*
+ * Don't MCR over reserved space. Ignore the ISA hole
+ * we frob around that catastrophe already
+ */
+ if (e820.map[i].type == E820_RESERVED) {
+ if (e820.map[i].addr >= 0x100000UL &&
+ e820.map[i].addr < clip)
+ clip = e820.map[i].addr;
+ continue;
+ }
+ start = e820.map[i].addr;
+ end = e820.map[i].addr + e820.map[i].size;
+ if (start >= end)
+ continue;
+ if (end > top)
+ top = end;
+ }
+ /*
+ * Everything below 'top' should be RAM except for the ISA hole.
+ * Because of the limited MCR's we want to map NV/ACPI into our
+ * MCR range for gunk in RAM
+ *
+ * Clip might cause us to MCR insufficient RAM but that is an
+ * acceptable failure mode and should only bite obscure boxes with
+ * a VESA hole at 15Mb
+ *
+ * The second case Clip sometimes kicks in is when the EBDA is marked
+ * as reserved. Again we fail safe with reasonable results
+ */
+ if (top > clip)
+ top = clip;
+
+ return top;
+}
+#endif
+
Index: linux-2.6/arch/x86/include/asm/e820.h
===================================================================
--- linux-2.6.orig/arch/x86/include/asm/e820.h
+++ linux-2.6/arch/x86/include/asm/e820.h
@@ -1,65 +1,9 @@
#ifndef _ASM_X86_E820_H
#define _ASM_X86_E820_H
-#define E820MAP 0x2d0 /* our map */
-#define E820MAX 128 /* number of entries in E820MAP */
-/*
- * Legacy E820 BIOS limits us to 128 (E820MAX) nodes due to the
- * constrained space in the zeropage. If we have more nodes than
- * that, and if we've booted off EFI firmware, then the EFI tables
- * passed us from the EFI firmware can list more nodes. Size our
- * internal memory map tables to have room for these additional
- * nodes, based on up to three entries per node for which the
- * kernel was built: MAX_NUMNODES == (1 << CONFIG_NODES_SHIFT),
- * plus E820MAX, allowing space for the possible duplicate E820
- * entries that might need room in the same arrays, prior to the
- * call to sanitize_e820_map() to remove duplicates. The allowance
- * of three memory map entries per node is "enough" entries for
- * the initial hardware platform motivating this mechanism to make
- * use of additional EFI map entries. Future platforms may want
- * to allow more than three entries per node or otherwise refine
- * this size.
- */
-
-/*
- * Odd: 'make headers_check' complains about numa.h if I try
- * to collapse the next two #ifdef lines to a single line:
- * #if defined(__KERNEL__) && defined(CONFIG_EFI)
- */
-#ifdef __KERNEL__
-#ifdef CONFIG_EFI
-#include <linux/numa.h>
-#define E820_X_MAX (E820MAX + 3 * MAX_NUMNODES)
-#else /* ! CONFIG_EFI */
-#define E820_X_MAX E820MAX
-#endif
-#else /* ! __KERNEL__ */
-#define E820_X_MAX E820MAX
-#endif
-
-#define E820NR 0x1e8 /* # entries in E820MAP */
-
-#define E820_RAM 1
-#define E820_RESERVED 2
-#define E820_ACPI 3
-#define E820_NVS 4
-#define E820_UNUSABLE 5
-
-/* reserved RAM used by kernel itself */
-#define E820_RESERVED_KERN 128
+#include <linux/fw_memmap.h>
#ifndef __ASSEMBLY__
-#include <linux/types.h>
-struct e820entry {
- __u64 addr; /* start of memory segment */
- __u64 size; /* size of memory segment */
- __u32 type; /* type of memory segment */
-} __attribute__((packed));
-
-struct e820map {
- __u32 nr_map;
- struct e820entry map[E820_X_MAX];
-};
#define ISA_START_ADDRESS 0xa0000
#define ISA_END_ADDRESS 0x100000
@@ -69,73 +13,20 @@ struct e820map {
#ifdef __KERNEL__
-#ifdef CONFIG_X86_OOSTORE
-extern int centaur_ram_top;
-void get_centaur_ram_top(void);
+#ifdef CONFIG_MEMTEST
+extern void early_memtest(unsigned long start, unsigned long end);
#else
-static inline void get_centaur_ram_top(void)
+static inline void early_memtest(unsigned long start, unsigned long end)
{
}
#endif
extern unsigned long pci_mem_start;
-extern int e820_any_mapped(u64 start, u64 end, unsigned type);
-extern int e820_all_mapped(u64 start, u64 end, unsigned type);
-extern void e820_add_region(u64 start, u64 size, int type);
-extern void e820_print_map(char *who);
-int sanitize_e820_map(void);
-void save_e820_map(void);
-extern u64 e820_update_range(u64 start, u64 size, unsigned old_type,
- unsigned new_type);
-extern u64 e820_remove_range(u64 start, u64 size, unsigned old_type,
- int checktype);
-extern void update_e820(void);
extern void e820_setup_gap(void);
-extern int e820_search_gap(unsigned long *gapstart, unsigned long *gapsize,
- unsigned long start_addr, unsigned long long end_addr);
struct setup_data;
extern void parse_e820_ext(struct setup_data *data, unsigned long pa_data);
-
-#if defined(CONFIG_X86_64) || \
- (defined(CONFIG_X86_32) && defined(CONFIG_HIBERNATION))
-extern void e820_mark_nosave_regions(unsigned long limit_pfn);
-#else
-static inline void e820_mark_nosave_regions(unsigned long limit_pfn)
-{
-}
-#endif
-
-#ifdef CONFIG_MEMTEST
-extern void early_memtest(unsigned long start, unsigned long end);
-#else
-static inline void early_memtest(unsigned long start, unsigned long end)
-{
-}
-#endif
-
-extern unsigned long end_user_pfn;
-
-extern u64 find_e820_area(u64 start, u64 end, u64 size, u64 align);
-extern u64 find_e820_area_size(u64 start, u64 *sizep, u64 align);
-extern u64 early_reserve_e820(u64 startt, u64 sizet, u64 align);
-#include <linux/early_res.h>
-
-extern unsigned long e820_end_of_ram_pfn(void);
-extern unsigned long e820_end_of_low_ram_pfn(void);
-extern int e820_find_active_region(const struct e820entry *ei,
- unsigned long start_pfn,
- unsigned long last_pfn,
- unsigned long *ei_startpfn,
- unsigned long *ei_endpfn);
-extern void e820_register_active_regions(int nid, unsigned long start_pfn,
- unsigned long end_pfn);
-extern u64 e820_hole_size(u64 start, u64 end);
-extern void finish_e820_parsing(void);
-extern void e820_reserve_resources(void);
-extern void e820_reserve_resources_late(void);
-extern void setup_memory_map(void);
extern char *default_machine_specific_memory_setup(void);
-
+extern void setup_memory_map(void);
/*
* Returns true iff the specified range [s,e) is completely contained inside
* the ISA region.
@@ -145,7 +36,18 @@ static inline bool is_ISA_range(u64 s, u
return s >= ISA_START_ADDRESS && e <= ISA_END_ADDRESS;
}
+#ifdef CONFIG_X86_OOSTORE
+extern int centaur_ram_top;
+int __get_special_low_ram_top(void);
+void get_centaur_ram_top(void);
+#else
+static inline void get_centaur_ram_top(void)
+{
+}
+#endif
+
#endif /* __KERNEL__ */
+
#endif /* __ASSEMBLY__ */
#ifdef __KERNEL__
Index: linux-2.6/include/linux/fw_memmap.h
===================================================================
--- /dev/null
+++ linux-2.6/include/linux/fw_memmap.h
@@ -0,0 +1,114 @@
+#ifndef _LINUX_FW_MEMMAP_H
+#define _LINUX_FW_MEMMAP_H
+#define E820MAX 128 /* number of entries in E820MAP */
+
+/*
+ * Legacy E820 BIOS limits us to 128 (E820MAX) nodes due to the
+ * constrained space in the zeropage. If we have more nodes than
+ * that, and if we've booted off EFI firmware, then the EFI tables
+ * passed us from the EFI firmware can list more nodes. Size our
+ * internal memory map tables to have room for these additional
+ * nodes, based on up to three entries per node for which the
+ * kernel was built: MAX_NUMNODES == (1 << CONFIG_NODES_SHIFT),
+ * plus E820MAX, allowing space for the possible duplicate E820
+ * entries that might need room in the same arrays, prior to the
+ * call to sanitize_e820_map() to remove duplicates. The allowance
+ * of three memory map entries per node is "enough" entries for
+ * the initial hardware platform motivating this mechanism to make
+ * use of additional EFI map entries. Future platforms may want
+ * to allow more than three entries per node or otherwise refine
+ * this size.
+ */
+
+/*
+ * Odd: 'make headers_check' complains about numa.h if I try
+ * to collapse the next two #ifdef lines to a single line:
+ * #if defined(__KERNEL__) && defined(CONFIG_EFI)
+ */
+#ifdef __KERNEL__
+#ifdef CONFIG_EFI
+#include <linux/numa.h>
+#define E820_X_MAX (E820MAX + 3 * MAX_NUMNODES)
+#else /* ! CONFIG_EFI */
+#define E820_X_MAX E820MAX
+#endif
+#else /* ! __KERNEL__ */
+#define E820_X_MAX E820MAX
+#endif
+
+#define E820_RAM 1
+#define E820_RESERVED 2
+#define E820_ACPI 3
+#define E820_NVS 4
+#define E820_UNUSABLE 5
+
+/* reserved RAM used by kernel itself */
+#define E820_RESERVED_KERN 128
+
+#ifndef __ASSEMBLY__
+#include <linux/types.h>
+struct e820entry {
+ __u64 addr; /* start of memory segment */
+ __u64 size; /* size of memory segment */
+ __u32 type; /* type of memory segment */
+} __attribute__((packed));
+
+struct e820map {
+ __u32 nr_map;
+ struct e820entry map[E820_X_MAX];
+};
+
+#ifdef __KERNEL__
+
+void clear_e820_map(void);
+int __append_e820_map(struct e820entry *biosmap, int nr_map);
+extern int e820_any_mapped(u64 start, u64 end, unsigned type);
+extern int e820_all_mapped(u64 start, u64 end, unsigned type);
+extern void e820_add_region(u64 start, u64 size, int type);
+extern void e820_print_map(char *who);
+int sanitize_e820_map(void);
+int __sanitize_e820_map(struct e820entry *biosmap, int max_nr, u32 *pnr_map);
+void save_e820_map(void);
+extern u64 e820_update_range(u64 start, u64 size, unsigned old_type,
+ unsigned new_type);
+extern u64 e820_remove_range(u64 start, u64 size, unsigned old_type,
+ int checktype);
+extern void update_e820(void);
+#define MAX_GAP_END 0x100000000ull
+extern int e820_search_gap(unsigned long *gapstart, unsigned long *gapsize,
+ unsigned long start_addr, unsigned long long end_addr);
+
+#if defined(CONFIG_X86_64) || \
+ (defined(CONFIG_X86_32) && defined(CONFIG_HIBERNATION))
+extern void e820_mark_nosave_regions(unsigned long limit_pfn);
+#else
+static inline void e820_mark_nosave_regions(unsigned long limit_pfn)
+{
+}
+#endif
+
+extern unsigned long end_user_pfn;
+
+extern u64 find_e820_area(u64 start, u64 end, u64 size, u64 align);
+extern u64 find_e820_area_size(u64 start, u64 *sizep, u64 align);
+extern u64 early_reserve_e820(u64 startt, u64 sizet, u64 align);
+#include <linux/early_res.h>
+
+extern unsigned long e820_end_of_ram_pfn(void);
+extern unsigned long e820_end_of_low_ram_pfn(void);
+extern int e820_find_active_region(const struct e820entry *ei,
+ unsigned long start_pfn,
+ unsigned long last_pfn,
+ unsigned long *ei_startpfn,
+ unsigned long *ei_endpfn);
+extern void e820_register_active_regions(int nid, unsigned long start_pfn,
+ unsigned long end_pfn);
+extern u64 e820_hole_size(u64 start, u64 end);
+extern void finish_e820_parsing(void);
+extern void e820_reserve_resources(void);
+extern void e820_reserve_resources_late(void);
+
+#endif /* __KERNEL__ */
+#endif /* __ASSEMBLY__ */
+
+#endif /* _LINUX_FW_MEMMAP_H */
Index: linux-2.6/kernel/Makefile
===================================================================
--- linux-2.6.orig/kernel/Makefile
+++ linux-2.6/kernel/Makefile
@@ -11,7 +11,7 @@ obj-y = sched.o fork.o exec_domain.o
hrtimer.o rwsem.o nsproxy.o srcu.o semaphore.o \
notifier.o ksysfs.o pm_qos_params.o sched_clock.o cred.o \
async.o range.o
-obj-$(CONFIG_HAVE_EARLY_RES) += early_res.o
+obj-$(CONFIG_HAVE_EARLY_RES) += early_res.o fw_memmap.o
obj-y += groups.o
ifdef CONFIG_FUNCTION_TRACER
Index: linux-2.6/include/linux/bootmem.h
===================================================================
--- linux-2.6.orig/include/linux/bootmem.h
+++ linux-2.6/include/linux/bootmem.h
@@ -6,7 +6,7 @@
#include <linux/mmzone.h>
#include <asm/dma.h>
-
+#include <linux/early_res.h>
/*
* simple boot-time physical memory area allocator.
*/
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/