[RFC PATCH 2/2] Alchemy: UART PM through serial framework.

[Manuel Lauss]

Hook up the Alchemy on-chip uarts with the platform 8250 PM callback
and enable/disable the uart blocks as needed.

Tested on Au1200.

Signed-off-by: Manuel Lauss <manuel.lauss@xxxxxxxxx>
---
 arch/mips/alchemy/common/platform.c |   17 +++++++++++++++++
 arch/mips/alchemy/common/power.c    |   32 --------------------------------
 2 files changed, 17 insertions(+), 32 deletions(-)

diff --git a/arch/mips/alchemy/common/platform.c b/arch/mips/alchemy/common/platform.c
index 2580e77..70f4abd 100644
--- a/arch/mips/alchemy/common/platform.c
+++ b/arch/mips/alchemy/common/platform.c
@@ -21,6 +21,22 @@
 #include <asm/mach-au1x00/au1100_mmc.h>
 #include <asm/mach-au1x00/au1xxx_eth.h>
 
+static void alchemy_8250_pm(struct uart_port *port, unsigned int state,
+			    unsigned int old_state)
+{
+	if (state == 0) {		/* power on */
+		__raw_writel(0, port->membase + UART_MOD_CNTRL);
+		wmb();
+		__raw_writel(1, port->membase + UART_MOD_CNTRL);
+		wmb();
+		__raw_writel(3, port->membase + UART_MOD_CNTRL);
+		wmb();
+	} else if (state == 3) {	/* power off */
+		__raw_writel(0, port->membase + UART_MOD_CNTRL);
+		wmb();
+	}
+}
+
 #define PORT(_base, _irq)					\
 	{							\
 		.mapbase	= _base,			\
@@ -30,6 +46,7 @@
 		.flags		= UPF_SKIP_TEST | UPF_IOREMAP |	\
 				  UPF_FIXED_TYPE,		\
 		.type		= PORT_16550A,			\
+		.pm		= alchemy_8250_pm,		\
 	}
 
 static struct plat_serial8250_port au1x00_uart_data[] = {
diff --git a/arch/mips/alchemy/common/power.c b/arch/mips/alchemy/common/power.c
index 6ab7b42..8fbf6d0 100644
--- a/arch/mips/alchemy/common/power.c
+++ b/arch/mips/alchemy/common/power.c
@@ -52,11 +52,6 @@
  * We only have to save/restore registers that aren't otherwise
  * done as part of a driver pm_* function.
  */
-static unsigned int sleep_uart0_inten;
-static unsigned int sleep_uart0_fifoctl;
-static unsigned int sleep_uart0_linectl;
-static unsigned int sleep_uart0_clkdiv;
-static unsigned int sleep_uart0_enable;
 static unsigned int sleep_usb[2];
 static unsigned int sleep_sys_clocks[5];
 static unsigned int sleep_sys_pinfunc;
@@ -68,19 +63,6 @@ static void save_core_regs(void)
 	extern void save_au1xxx_intctl(void);
 	extern void pm_eth0_shutdown(void);
 
-	/*
-	 * Do the serial ports.....these really should be a pm_*
-	 * registered function by the driver......but of course the
-	 * standard serial driver doesn't understand our Au1xxx
-	 * unique registers.
-	 */
-	sleep_uart0_inten = au_readl(UART0_ADDR + UART_IER);
-	sleep_uart0_fifoctl = au_readl(UART0_ADDR + UART_FCR);
-	sleep_uart0_linectl = au_readl(UART0_ADDR + UART_LCR);
-	sleep_uart0_clkdiv = au_readl(UART0_ADDR + UART_CLK);
-	sleep_uart0_enable = au_readl(UART0_ADDR + UART_MOD_CNTRL);
-	au_sync();
-
 #ifndef CONFIG_SOC_AU1200
 	/* Shutdown USB host/device. */
 	sleep_usb[0] = au_readl(USB_HOST_CONFIG);
@@ -186,20 +168,6 @@ static void restore_core_regs(void)
 	au_writel(sleep_static_memctlr[3][1], MEM_STTIME3);
 	au_writel(sleep_static_memctlr[3][2], MEM_STADDR3);
 
-	/*
-	 * Enable the UART if it was enabled before sleep.
-	 * I guess I should define module control bits........
-	 */
-	if (sleep_uart0_enable & 0x02) {
-		au_writel(0, UART0_ADDR + UART_MOD_CNTRL); au_sync();
-		au_writel(1, UART0_ADDR + UART_MOD_CNTRL); au_sync();
-		au_writel(3, UART0_ADDR + UART_MOD_CNTRL); au_sync();
-		au_writel(sleep_uart0_inten, UART0_ADDR + UART_IER); au_sync();
-		au_writel(sleep_uart0_fifoctl, UART0_ADDR + UART_FCR); au_sync();
-		au_writel(sleep_uart0_linectl, UART0_ADDR + UART_LCR); au_sync();
-		au_writel(sleep_uart0_clkdiv, UART0_ADDR + UART_CLK); au_sync();
-	}
-
 	restore_au1xxx_intctl();
 
 #if defined(CONFIG_SOC_AU1550) || defined(CONFIG_SOC_AU1200)
-- 
1.7.0.2

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/