[PATCH v2 2/3] hwmon: SMM665 driver documentation
From: Guenter Roeck
Date: Fri Jun 25 2010 - 10:41:50 EST
Signed-off-by: Guenter Roeck <guenter.roeck@xxxxxxxxxxxx>
---
Documentation/hwmon/smm665 | 151 ++++++++++++++++++++++++++++++++++++++++++++
1 files changed, 151 insertions(+), 0 deletions(-)
create mode 100644 Documentation/hwmon/smm665
diff --git a/Documentation/hwmon/smm665 b/Documentation/hwmon/smm665
new file mode 100644
index 0000000..8c08f63
--- /dev/null
+++ b/Documentation/hwmon/smm665
@@ -0,0 +1,151 @@
+Kernel driver smm665
+====================
+
+Supported chips:
+ * Summit Microelectronics SMM465
+ Prefix: 'smm465'
+ Addresses scanned: -
+ Datasheet: Publicly available at the Summit Microelectronics website.
+ * Summit Microelectronics SMM665, SMM665B
+ Prefix: 'smm665'
+ Addresses scanned: -
+ Datasheet: Publicly available at the Summit Microelectronics website.
+ * Summit Microelectronics SMM665C
+ Prefix: 'smm665c'
+ Addresses scanned: -
+ Datasheet: Publicly available at the Summit Microelectronics website.
+ * Summit Microelectronics SMM764
+ Prefix: 'smm764'
+ Addresses scanned: -
+ Datasheet: Publicly available at the Summit Microelectronics website.
+ * Summit Microelectronics SMM766
+ Prefix: 'smm766'
+ Addresses scanned: -
+ Datasheet: Publicly available at the Summit Microelectronics website.
+
+Author: Guenter Roeck <guenter.roeck@xxxxxxxxxxxx>
+
+
+Module Parameters
+-----------------
+
+* vref: int
+ Default: 1250 (mV)
+ Reference voltage on VREF_ADC pin in mV. It should not be necessary to set
+ this parameter unless a non-default reference voltage is used.
+
+
+Description
+-----------
+
+[From datasheet] The SMM665 is an Active DC Output power supply Controller
+that monitors, margins and cascade sequences power. The part monitors six
+power supply channels as well as VDD, 12V input, two general-purpose analog
+inputs and an internal temperature sensor using a 10-bit ADC.
+
+Each monitored channel has its own high and low limits, plus a critical
+limit.
+
+Support for SMM465, SMM764, and SMM766 has been implemented but is untested.
+
+
+Usage Notes
+-----------
+
+This driver does not probe for devices, since there is no register which
+can be safely used to identify the chip. You will have to instantiate
+the devices explicitly. When instantiating the device, you have to specify
+its configuration register address.
+
+Example: the following will load the driver for an SMM665 at address 0x57
+on I2C bus #1:
+$ modprobe smm665
+$ echo smm665 0x57 > /sys/bus/i2c/devices/i2c-1/new_device
+
+
+Sysfs entries
+-------------
+
+This driver uses the values in the datasheet to convert ADC register values
+into the values specified in the sysfs-interface document. All attributes are
+read only.
+
+Min, max, lcrit, and crit values are used by the chip to trigger external signals
+and/or other activity. Triggered signals can include HEALTHY, RST, Power Off,
+or Fault depending on the chip configuration. The driver reports values as lcrit
+or crit if exceeding the limits triggers RST, Power Off, or Fault, and as min or
+max otherwise. For details please see the SMM665 datasheet.
+
+For SMM465 and SMM764, values for Channel E and F are reported but undefined.
+
+in1_input 12V input voltage (mV)
+in2_input 3.3V (VDD) input voltage (mV)
+in3_input Channel A voltage (mV)
+in4_input Channel B voltage (mV)
+in5_input Channel C voltage (mV)
+in6_input Channel D voltage (mV)
+in7_input Channel E voltage (mV)
+in8_input Channel F voltage (mV)
+in9_input AIN1 voltage (mV)
+in10_input AIN2 voltage (mV)
+
+in1_min 12v input minimum voltage (mV)
+in2_min 3.3V (VDD) input minimum voltage (mV)
+in3_min Channel A minimum voltage (mV)
+in4_min Channel B minimum voltage (mV)
+in5_min Channel C minimum voltage (mV)
+in6_min Channel D minimum voltage (mV)
+in7_min Channel E minimum voltage (mV)
+in8_min Channel F minimum voltage (mV)
+in9_min AIN1 minimum voltage (mV)
+in10_min AIN2 minimum voltage (mV)
+
+in1_max 12v input maximum voltage (mV)
+in2_max 3.3V (VDD) input maximum voltage (mV)
+in3_max Channel A maximum voltage (mV)
+in4_max Channel B maximum voltage (mV)
+in5_max Channel C maximum voltage (mV)
+in6_max Channel D maximum voltage (mV)
+in7_max Channel E maximum voltage (mV)
+in8_max Channel F maximum voltage (mV)
+in9_max AIN1 maximum voltage (mV)
+in10_max AIN2 maximum voltage (mV)
+
+in1_lcrit 12v input critical minimum voltage (mV)
+in2_lcrit 3.3V (VDD) input critical minimum voltage (mV)
+in3_lcrit Channel A critical minimum voltage (mV)
+in4_lcrit Channel B critical minimum voltage (mV)
+in5_lcrit Channel C critical minimum voltage (mV)
+in6_lcrit Channel D critical minimum voltage (mV)
+in7_lcrit Channel E critical minimum voltage (mV)
+in8_lcrit Channel F critical minimum voltage (mV)
+in9_lcrit AIN1 critical minimum voltage (mV)
+in10_lcrit AIN2 critical minimum voltage (mV)
+
+in1_crit 12v input critical maximum voltage (mV)
+in2_crit 3.3V (VDD) input critical maximum voltage (mV)
+in3_crit Channel A critical maximum voltage (mV)
+in4_crit Channel B critical maximum voltage (mV)
+in5_crit Channel C critical maximum voltage (mV)
+in6_crit Channel D critical maximum voltage (mV)
+in7_crit Channel E critical maximum voltage (mV)
+in8_crit Channel F critical maximum voltage (mV)
+in9_crit AIN1 critical maximum voltage (mV)
+in10_crit AIN2 critical maximum voltage (mV)
+
+in1_fault 12v input fault
+in2_fault 3.3V (VDD) input fault
+in3_fault Channel A fault
+in4_fault Channel B fault
+in5_fault Channel C fault
+in6_fault Channel D fault
+in7_fault Channel E fault
+in8_fault Channel F fault
+in9_fault AIN1 fault
+in10_fault AIN2 fault
+
+temp1_input Chip tempererature
+temp1_min Mimimum chip tempererature
+temp1_max Maximum chip tempererature
+temp1_crit Critical chip tempererature
+temp1_fault Temperature fault
--
1.7.0.87.g0901d
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/