Re: Possible bug in net/ipv4/route.c?

[Stephen Hemminger]

On Mon, 5 Jul 2010 20:04:13 +0800
Herbert Xu <herbert@xxxxxxxxxxxxxxxxxxx> wrote:

> Sol Kavy <skavy@xxxxxxxxxx> wrote:
> > Found Linux: 2.6.28
> > Arch: Ubicom32 <not yet pushed>
> > Project: uCLinux based Router
> > Test: Bit torrent Stress Test
> > 
> > Note: The top of Linus git net/ipv4/route.c appears to have the same issue.
> > 
> > The following is a patch for clearing out IP options area in an input skb during link failure processing.  Without this patch, the icmp_send() can result in a call to ip_options_echo() where the common buffer area of the skb is incorrectly interpreted.  Depending on the previous use of the skb->cb[], the interpreted option length values can cause stack corruption by copying more than 40 bytes to the output options.
> > 
> > In our case, a driver is using the skb->cb[] area to hold driver specific data.   The driver is not zeroing out the area after use.  I can see three basic solutions:
> > 
> > 1) Drivers are not allowed to use the skb->cb[] area at all.  Ubicom should modify the driver to use a different approach.
> > 
> > 2) The layer using skb->cb[] should clear this area after use and before handing the skb to another layer.  Ubicom should modify the driver to clear the skb->cb[] area before sending it up the line.
> > 
> > 3) Any layer that "uses" the skb->cb[] area must clear the area before use.  In which case, the proposed patch would fix the problem for the ipv4_link_failure().  I believe that this is the correct fix because I see ip_rcv() clears the skb->cb[] before using it.
> > 
> > Can someone confirm that this is the appropriate fix?  If this is documented somewhere, please direct me to the documentation.
> 
> Thanks for the report!
>  
> > Patch:  
> > 
> > diff --git a/net/ipv4/route.c b/net/ipv4/route.c
> > index 125ee64..d13805f 100644
> > --- a/net/ipv4/route.c
> > +++ b/net/ipv4/route.c
> > @@ -1606,6 +1606,14 @@ static void ipv4_link_failure(struct sk_buff *skb)
> > {
> >         struct rtable *rt;
> > 
> > +       /*
> > +         * Since link failure can be called with skbs from many layers (see arp)
> > +         * the cb area of the skb must be cleared before use. Because the cb area 
> > +         * can be formatted according to the caller layer's cb area format and it may cause
> > +         * corruptions when it is handled in a different network layer.
> > +         */
> > +       memset(&(IPCB(skb)->opt), 0, sizeof(IPCB(skb)->opt));
> >         icmp_send(skb, ICMP_DEST_UNREACH, ICMP_HOST_UNREACH, 0);
> >         rt = skb->rtable;
> > 
> > The packet is enqueud by:
> > do_IRQ()->do_softirq()->__do_softirq()->net_rx_action()->ubi32_eth_napi_poll()->ubi32_eth_receive()->__vlan_hwaccel_rx()->netif_receive_skb()->br_handle_frame()->nf_hook_slow()->br_nf_pre_routing_finish()->br_nfr_pre_routing_finish_bridge()->neight_resolve_output()->__neigh_event_send().
> > 
> > The packet is then dequeued by: 
> > do_IRQ() -> irq_exit() -> do_softirq() -> run_timer_softirq() -> neigh_timer_handler() -> arp_error_report() -> ipv4_link_failure() -> icmp_send() -> ip_options_echo().
> > 
> > Because the Ubicom Ethernet driver overwrites the common buffer area, the enqueued packet contains garbage when casted as an IP options data structure.  This results in ip_options_echo() miss reading the option length information and overwriting memory.  By clearing the skb->cb[] before processing the icmp_send() against the packet, we ensure that ip_options_echo() does not corrupt memory.   
> 
> Generally this area should be cleared on entry to each stack
> intending on using it.  So in this case, I'd point the finger
> of blame at the bridge stack for letting this packet into the
> IP stack through the back entrance without taking the proper
> precautions.

The CB is used in two places in the bridge code.
1) The recent multicast changes (IGMP)
2) Netfilter / ebtables to store header.

Ebtables is okay because the only part of the cb[] it uses
is the incoming device (brdev) which is always initialized coming into
the bridge: br_dev_xmit and br_handle_frame_finish

The IGMP code looks buggy.

/* net device transmit always called with no BH (preempt_disabled) */
netdev_tx_t br_dev_xmit(struct sk_buff *skb, struct net_device *dev)
{
... [A]
	BR_INPUT_SKB_CB(skb)->brdev = dev;

	skb_reset_mac_header(skb);
	skb_pull(skb, ETH_HLEN);

	if (is_multicast_ether_addr(dest)) {
		if (br_multicast_rcv(br, NULL, skb))
			goto out;

		mdst = br_mdb_get(br, skb);
		if (mdst || BR_INPUT_SKB_CB_MROUTERS_ONLY(skb))
			... [B]

The problem is that br_dev_xmit is looking at flags in the CB[] that
are uninitialized.

if br_dev_xmit cleared the CB at [A] the mrouters_only would always be zero
at [B].

Where should the mrouters and igmp_only fields in skb be initialized?


--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/