Re: [PATCH] mtd: nand: Fix regression in BBM detection

[Abdoulaye Walsimou GAYE]

On 08/18/2010 08:25 PM, Brian Norris wrote:
> Commit c7b28e25cb9beb943aead770ff14551b55fa8c79 caused a regression
> in detection of factory-set bad block markers, especially for certain
> small-page NAND. This fix removes some unneeded constraints on using
> NAND_SMALL_BADBLOCK_POS, making the detection code more correct.
>
> This regression can be seen, for example, in Hynix HY27US081G1M and
> similar.
>
> Signed-off-by: Brian Norris<norris@xxxxxxxxxxxx>
> ---
>   drivers/mtd/nand/nand_base.c |   10 +++-------
>   1 files changed, 3 insertions(+), 7 deletions(-)
>
> diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c
> index a3c7473..a22ed7b 100644
> --- a/drivers/mtd/nand/nand_base.c
> +++ b/drivers/mtd/nand/nand_base.c
> @@ -2934,14 +2934,10 @@ static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd,
>   		chip->chip_shift = ffs((unsigned)(chip->chipsize>>  32)) + 32 - 1;
>
>   	/* Set the bad block position */
> -	if (!(busw&  NAND_BUSWIDTH_16)&&  (*maf_id == NAND_MFR_STMICRO ||
> -				(*maf_id == NAND_MFR_SAMSUNG&&
> -				 mtd->writesize == 512) ||
> -				*maf_id == NAND_MFR_AMD))
> -		chip->badblockpos = NAND_SMALL_BADBLOCK_POS;
> -	else
> +	if (mtd->writesize>  512 || (busw&  NAND_BUSWIDTH_16))
>   		chip->badblockpos = NAND_LARGE_BADBLOCK_POS;
> -
> +	else
> +		chip->badblockpos = NAND_SMALL_BADBLOCK_POS;
>
>   	/* Get chip options, preserve non chip based options */
>   	chip->options&= ~NAND_CHIPOPTIONS_MSK;
>    

Brian,
Sorry for the long delay!
I tested the above patch unfortunately it does not help in my case!
And when I go further and put a JFFS2 in that partition and boot the
board I have

(S3c2410 nand hardware ECC enable):
mtd->read(0x400 bytes from 0x1274000) returned ECC error
mtd->read(0x3c08 bytes from 0x12743f8) returned ECC error

(without S3c2410 nand hardware ECC enable):
uncorrectable error :
uncorrectable error :
uncorrectable error :
uncorrectable error :
mtd->read(0x400 bytes from 0x1274000) returned ECC error
uncorrectable error :
uncorrectable error :
uncorrectable error :
[...]
uncorrectable error :
uncorrectable error :
mtd->read(0x3c08 bytes from 0x12743f8) returned ECC error

Despite these errors I can actually use the board (no kernel panic)!
The part is Samsung K9F1208U0C - PCB0

Hope that helps!

Thanks,
AWG

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/