Re: [PATCH] Platform: add Samsung Laptop platform driver

[Matthew Garrett]

On Wed, Feb 09, 2011 at 02:40:06PM -0800, Greg KH wrote:

> +/* Structure to get data back to the calling function */
> +struct sabi_retval {
> +	u8 retval[20];
> +};

20 bytes, but only 4 of them end up being used?

> +	if (readb(sabi_iface + SABI_IFACE_COMPLETE) == 0xaa &&
> +	    readb(sabi_iface + SABI_IFACE_DATA) != 0xff) {
> +		/*
> +		 * It did!
> +		 * Save off the data into a structure so the caller use it.
> +		 * Right now we only care about the first 4 bytes,
> +		 * I suppose there are commands that need more, but I don't
> +		 * know about them.
> +		 */
> +		sretval->retval[0] = readb(sabi_iface + SABI_IFACE_DATA);
> +		sretval->retval[1] = readb(sabi_iface + SABI_IFACE_DATA + 1);
> +		sretval->retval[2] = readb(sabi_iface + SABI_IFACE_DATA + 2);
> +		sretval->retval[3] = readb(sabi_iface + SABI_IFACE_DATA + 3);
> +		goto exit;
> +	}

goto on success, continue failure? That's a pretty atypical pattern, and 
the goto's not even really needed in this case.

> +	/* Something bad happened, so report it and error out */
> +	printk(KERN_WARNING "SABI command 0x%02x failed with completion flag 0x%02x and output 0x%02x\n",
> +		command, readb(sabi_iface + SABI_IFACE_COMPLETE),
> +		readb(sabi_iface + SABI_IFACE_DATA));

Is it guaranteed that further reads will still return the failure state?

> +	/* see if the command actually succeeded */
> +	if (readb(sabi_iface + SABI_IFACE_COMPLETE) == 0xaa &&
> +	    readb(sabi_iface + SABI_IFACE_DATA) != 0xff) {
> +		/* it did! */
> +		goto exit;
> +	}

Ditto for this block.

> +static struct dmi_system_id __initdata samsung_dmi_table[] = {

This is kind of ugly. Are there any Samsung laptops where reading the 
bios area is going to cause problems?

> +	/* Get a pointer to the SABI Interface */
> +	ifaceP = (readw(sabi + sabi_config->header_offsets.data_segment) & 0x0ffff) << 4;
> +	ifaceP += readw(sabi + sabi_config->header_offsets.data_offset) & 0x0ffff;
> +	sabi_iface = ioremap(ifaceP, 16);
> +	if (!sabi_iface) {
> +		printk(KERN_ERR "Can't remap %x\n", ifaceP);

dev_err()? It'd be nice to have a prefix on the failure cases.

> +	retval = init_wireless(sdev);

No way to identify whether or not the hardware has wifi before 
registering rfkill?

-- 
Matthew Garrett | mjg59@xxxxxxxxxxxxx
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/