Re: [PATCH, resend] x86/PCI: don't export a __devinit function

[Mauro Carvalho Chehab]

Em 17-02-2011 14:08, Jan Beulich escreveu:
> Exporting a __devinit function (pcibios_scan_specific_bus()) isn't
> correct. (Michal, any reason why modpost only warns about exported
> __init functions?) Short of being able to think of a better solution,
> and short of making the whole call tree (reaching into the arch-
> independent part of the PCI subsystem) non-__devinit, export the
> symbol only when HOTPLUG is enabled (which is always the case for non-
> expert configurations), use section mismatch avoidance annotations for
> that case (knowing that __devinit functions will not be discarded),
> and mark the symbol __devinit only in the !HOTPLUG case.
> 
> Consequently, EDAC_I7CORE (consuming the export) then has to depend on
> HOTPLUG. 

Having the entire i7core_edac driver depending on HOTPLUG, just because
a few BIOSes want to hide the non-core PCI devices doesn't seem nice.
One alternative would be to enclose the code that needs this function
with #ifdef CONFIG_HOTPLUG.

> A fundamental question of course if whether this driver has
> to use that function in the first place (i.e. whether it wouldn't be
> better to just remove the export) - the problem it tries to address
> happens on other systems too, but the PCI bus the devices in question
> live on isn't necessarily bus 255. For the affected system I have, the
> alternative approach is to set pcibios_last_bus from __pci_mmcfg_init()
> based on the highest bus number on segment 0 being covered by MCFG.

I received a few days ago a report that some BIOSes that hide those
PCI devices also use a different address for the last bus (0x3f, instead
of 0xff). So, it seems that the better would be to use an alternative
way to retrieve the last bus.

> 
> Signed-off-by: Jan Beulich <jbeulich@xxxxxxxxxx>
> Cc: Mauro Carvalho Chehab <mchehab@xxxxxxxxxx>
> Cc: Aristeu Sergio <arozansk@xxxxxxxxxx>
> Cc: Michal Marek <mmarek@xxxxxxx>
> 
> ---
>  arch/x86/pci/legacy.c |   21 ++++++++++++++++++---
>  drivers/edac/Kconfig  |    2 +-
>  2 files changed, 19 insertions(+), 4 deletions(-)
> 
> --- 2.6.38-rc5/arch/x86/pci/legacy.c
> +++ 2.6.38-rc5-x86-pci-section-conflict/arch/x86/pci/legacy.c
> @@ -36,7 +36,23 @@ int __init pci_legacy_init(void)
>  	return 0;
>  }
>  
> -void __devinit pcibios_scan_specific_bus(int busn)
> +#ifdef CONFIG_HOTPLUG
> +static void __ref
> +#else
> +static inline void
> +#endif
> +_pci_scan_bus_on_node(int busno, int node)
> +{
> +	pci_scan_bus_on_node(busno, &pci_root_ops, node);
> +}
> +
> +#ifdef CONFIG_HOTPLUG
> +EXPORT_SYMBOL_GPL(pcibios_scan_specific_bus);
> +void
> +#else
> +void __devinit
> +#endif
> +pcibios_scan_specific_bus(int busn)
>  {
>  	int devfn;
>  	long node;
> @@ -51,12 +67,11 @@ void __devinit pcibios_scan_specific_bus
>  		    l != 0x0000 && l != 0xffff) {
>  			DBG("Found device at %02x:%02x [%04x]\n", busn, devfn, l);
>  			printk(KERN_INFO "PCI: Discovered peer bus %02x\n", busn);
> -			pci_scan_bus_on_node(busn, &pci_root_ops, node);
> +			_pci_scan_bus_on_node(busn, node);
>  			return;
>  		}
>  	}
>  }
> -EXPORT_SYMBOL_GPL(pcibios_scan_specific_bus);
>  
>  int __init pci_subsys_init(void)
>  {
> --- 2.6.38-rc5/drivers/edac/Kconfig
> +++ 2.6.38-rc5-x86-pci-section-conflict/drivers/edac/Kconfig
> @@ -173,7 +173,7 @@ config EDAC_I5400
>  
>  config EDAC_I7CORE
>  	tristate "Intel i7 Core (Nehalem) processors"
> -	depends on EDAC_MM_EDAC && PCI && X86
> +	depends on EDAC_MM_EDAC && PCI && X86 && HOTPLUG
>  	select EDAC_MCE
>  	help
>  	  Support for error detection and correction the Intel
> 
> 
> 

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/