RE: sata_mv port lockup on hotplug (kernel 2.6.38.2)

From: Bruce Stenning
Date: Mon Apr 25 2011 - 07:07:20 EST

Next message: Mel Gorman: "Re: [patch] mm/vmalloc: remove block allocation bitmap"
Previous message: Tejun Heo: "Re: [PATCH v2 4/7] signal: sigprocmask: narrow the scope of->siglock"
Next in thread: Tejun Heo: "Re: sata_mv port lockup on hotplug (kernel 2.6.38.2)"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Hi Mark, Tejun,

> Sorry about delay. -EWASTRAVELING

:-)

After further investigation it looks like there might be more than one thing
going on here. I have managed to lock up ports by unplugging and reinserting
just the sata data cable (thereby avoiding any potential issues with the
hotplug backplane/power.) Dumping the registers after such a lockup shows
clearly that the irq for the locked port is disabled.

I had previously reported that port lockups happened such that the irq for
every port was enabled. I suspect that this is due to the hotplug backplane
on the pre-production unit that I am testing with. Our production units have
proper surge protection on the backplanes, but the early pre-production
versions did not, and I think this is what causes this other mode of port
lockup. Of course, there may be something else going on here but for the
time being I have concentrated on investigating the lockups caused by removing
and reinserting just the sata data cable. The presence of a separate problem
may invalidate other investigations and assertions I had previously made.

I have been able to reproduce this port lockup both with and without the
additional spinlock in mv_set_main_irq_mask. If I add more than very
rudimentary tracing in mv_write_main_irq_mask, then the race is avoided
(as you had indicated, Mark.) I am able to reproduce the lockup with minimal
tracing in mv_write_main_irq_mask and with libata tracing enabled; I have
attached the patch and the tracing leading up to port lockup below (this
is with the additional spinlock in mv_set_main_irq_mask.) Apologies for the
length...

Please note the warning generated by ata_sff_hsm_move on the line:

WARN_ON_ONCE((qc->flags & ATA_QCFLAG_ACTIVE) == 0);

I have been looking at code paths in libata into sata_mv, but I'm afraid I am
not au fait with the libata architecture yet.

Tejun, what does it mean to limit a sata link to UDMA/100? I thought that this
was only for ata devices, and sata devices have the choice of 1.5Gbps, 3Gbps,
or 6 Gbps. Is that a false assumption? Is it related to early sata devices that
were still somewhat based on parallel ata designs?

I shall be out-of-office from Wednesday for the best part of the next three
weeks, but I shall endeavour to get back to you if you have any queries during
that time.

Kind Regards,

Bruce.

Bruce Stenning,
IndigoVision,
b <dot> stenning <at> indigovision <dot> com

@@ -1022,20 +1027,33 @@
if (mask & (ALL_PORTS_COAL_DONE | PORTS_4_7_COAL_DONE))
mask &= ~DONE_IRQ_4_7;
writelfl(mask, hpriv->main_irq_mask_addr);
+#if 1
+ printk("%08x\n", mask);
+#endif
}

[ra_145_82]$ insmod sata_mv.ko
sata_mv 0000:00:04.0: version 1.28
ata_host_alloc: ENTER
ata_port_alloc: ENTER
ata_port_alloc: ENTER
ata_port_alloc: ENTER
ata_port_alloc: ENTER
PCI: enabling device 0000:00:04.0 (0140 -> 0143)
mv_port_init: EDMA cfg=0x0000291f EDMA IRQ err cause/mask=0x00000000/0xfc1e9fff
mv_port_init: EDMA cfg=0x0000291f EDMA IRQ err cause/mask=0x00000000/0xfc1e9fff
mv_port_init: EDMA cfg=0x0000291f EDMA IRQ err cause/mask=0x00000000/0xfc1e9fff
mv_port_init: EDMA cfg=0x0000291f EDMA IRQ err cause/mask=0x00000000/0xfc1e9fff
mv_init_host: HC0: HC config=0x000100ff HC IRQ cause (before clear)=0x00000000
00040000
mv_dump_pci_cfg: 00: 604111ab 02b00143 01000009 00000008
mv_dump_pci_cfg: 10: 80000004 00000000 00001001 00000000
mv_dump_pci_cfg: 20: 00000000 00000000 00000000 11ab11ab
mv_dump_pci_cfg: 30: 00000000 00000040 00000000 0000011a
mv_dump_pci_cfg: 40: 00025001 00000000 00000000 00000000
mv_dump_pci_cfg: 50: 00806005 00000000 00000000 00000000
mv_dump_pci_cfg: 60: 00300007 0183fff8
sata_mv 0000:00:04.0: Gen-II 32 slots 4 ports SCSI mode IRQ via INTx
__ata_port_freeze: ata4294967295 port frozen
__ata_port_freeze: ata4294967295 port frozen
__ata_port_freeze: ata4294967295 port frozen
__ata_port_freeze: ata4294967295 port frozen
scsi0 : sata_mv
scsi1 : sata_mv
scsi2 : sata_mv
scsi3 : sata_mv
ata1: FORCE: PHY spd limit set to 1.5Gbps
ata1: SATA max UDMA/133 mmio m1048576@0x80000000 port 0x80022000 irq 26
ata2: FORCE: PHY spd limit set to 1.5Gbps
ata2: SATA max UDMA/133 mmio m1048576@0x80000000 port 0x80024000 irq 26
ata3: FORCE: PHY spd limit set to 1.5Gbps
ata3: SATA max UDMA/133 mmio m1048576@0x80000000 port 0x80026000 irq 26
ata4: FORCE: PHY spd limit set to 1.5Gbps
ata4: SATA max UDMA/133 mmio m1048576@0x80000000 port 0x80028000 irq 26
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_sff_flush_pio_task: ENTER
ata_eh_link_autopsy: ENTER
ata_eh_recover: ENTER
__ata_port_freeze: ata1 port frozen
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata1: bus reset via SRST
ata1: link is slow to respond, please be patient (ready=0)
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040001
ata_eh_thaw_port: ata1 port thawed
ata_std_postreset: ENTER
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata1: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata1: cmd 0xEC
ata_sff_hsm_move: ata1: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata1: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata1: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata1: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata1: cmd 0x27
ata_sff_hsm_move: ata1: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata1: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0407 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x007f 93==0x0000
ata1.00: ATA-8: ST31000525SV, CV11, max UDMA/133
ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata_dev_set_xfermode: set features - xfer mode
ata1: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x3 nsect 0x46 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata1: cmd 0xEF
ata_sff_hsm_move: ata1: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata1: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dev_set_xfermode: EXIT, err_mask=0
ata1: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata1: cmd 0xEC
ata_sff_hsm_move: ata1: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata1: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata1: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata1: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata1: cmd 0x27
ata_sff_hsm_move: ata1: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata1: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x407f 93==0x0000
ata_dev_set_mode: xfer_shift=12, xfer_mode=0x46
ata1.00: configured for UDMA/133
ata_eh_recover: EXIT, rc=0
ata_scsi_error: EXIT
ata_scsi_dump_cdb: CDB (1:0,0,0) 12 00 00 00 24 00 00 00 00
ata_scsiop_inq_std: ENTER
ata_scsi_dump_cdb: CDB (1:0,0,0) 12 00 00 00 60 00 00 00 00
ata_scsiop_inq_std: ENTER
scsi 0:0:0:0: Direct-Access ATA ST31000525SV CV11 PQ: 0 ANSI: 5
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_sff_flush_pio_task: ENTER
ata_eh_link_autopsy: ENTER
ata_eh_recover: ENTER
__ata_port_freeze: ata2 port frozen
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata2: bus reset via SRST
ata2: link is slow to respond, please be patient (ready=0)
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040005
ata_eh_thaw_port: ata2 port thawed
ata_std_postreset: ENTER
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata2: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata2: cmd 0xEC
ata_sff_hsm_move: ata2: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata2: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata2: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata2: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata2: cmd 0x27
ata_sff_hsm_move: ata2: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata2: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0407 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x007f 93==0x0000
ata2.00: ATA-8: ST31000525SV, CV11, max UDMA/133
ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata_dev_set_xfermode: set features - xfer mode
ata2: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x3 nsect 0x46 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata2: cmd 0xEF
ata_sff_hsm_move: ata2: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata2: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dev_set_xfermode: EXIT, err_mask=0
ata2: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata2: cmd 0xEC
ata_sff_hsm_move: ata2: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata2: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata2: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata2: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata2: cmd 0x27
ata_sff_hsm_move: ata2: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata2: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x407f 93==0x0000
ata_dev_set_mode: xfer_shift=12, xfer_mode=0x46
ata2.00: configured for UDMA/133
ata_eh_recover: EXIT, rc=0
ata_scsi_error: EXIT
ata_scsi_dump_cdb: CDB (2:0,0,0) 12 00 00 00 24 00 00 00 00
ata_scsiop_inq_std: ENTER
ata_scsi_dump_cdb: CDB (2:0,0,0) 12 00 00 00 60 00 00 00 00
ata_scsiop_inq_std: ENTER
scsi 1:0:0:0: Direct-Access ATA ST31000525SV CV11 PQ: 0 ANSI: 5
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_sff_flush_pio_task: ENTER
ata_eh_link_autopsy: ENTER
ata_eh_recover: ENTER
__ata_port_freeze: ata3 port frozen
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata3: bus reset via SRST
ata3: link is slow to respond, please be patient (ready=0)
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040015
ata_eh_thaw_port: ata3 port thawed
ata_std_postreset: ENTER
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata3: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata3: cmd 0xEC
ata_sff_hsm_move: ata3: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata3: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata3: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata3: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata3: cmd 0x27
ata_sff_hsm_move: ata3: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata3: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0407 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x007f 93==0x0000
ata3.00: ATA-8: ST31000525SV, CV11, max UDMA/133
ata3.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata_dev_set_xfermode: set features - xfer mode
ata3: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x3 nsect 0x46 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata3: cmd 0xEF
ata_sff_hsm_move: ata3: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata3: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dev_set_xfermode: EXIT, err_mask=0
ata3: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata3: cmd 0xEC
ata_sff_hsm_move: ata3: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata3: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata3: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata3: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata3: cmd 0x27
ata_sff_hsm_move: ata3: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata3: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x407f 93==0x0000
ata_dev_set_mode: xfer_shift=12, xfer_mode=0x46
ata3.00: configured for UDMA/133
ata_eh_recover: EXIT, rc=0
ata_scsi_error: EXIT
ata_scsi_dump_cdb: CDB (3:0,0,0) 12 00 00 00 24 00 00 00 00
ata_scsiop_inq_std: ENTER
ata_scsi_dump_cdb: CDB (3:0,0,0) 12 00 00 00 60 00 00 00 00
ata_scsiop_inq_std: ENTER
scsi 2:0:0:0: Direct-Access ATA ST31000525SV CV11 PQ: 0 ANSI: 5
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_sff_flush_pio_task: ENTER
ata_eh_link_autopsy: ENTER
ata_eh_recover: ENTER
__ata_port_freeze: ata4 port frozen
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata4: bus reset via SRST
ata4: link is slow to respond, please be patient (ready=0)
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata4: cmd 0x27
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0407 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x007f 93==0x0000
ata4.00: ATA-8: ST31000525SV, CV11, max UDMA/133
ata4.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata_dev_set_xfermode: set features - xfer mode
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x3 nsect 0x46 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEF
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dev_set_xfermode: EXIT, err_mask=0
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata4: cmd 0x27
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x407f 93==0x0000
ata_dev_set_mode: xfer_shift=12, xfer_mode=0x46
ata4.00: configured for UDMA/133
ata_eh_recover: EXIT, rc=0
ata_scsi_error: EXIT
ata_scsi_dump_cdb: CDB (4:0,0,0) 12 00 00 00 24 00 00 00 00
ata_scsiop_inq_std: ENTER
ata_scsi_dump_cdb: CDB (4:0,0,0) 12 00 00 00 60 00 00 00 00
ata_scsiop_inq_std: ENTER
scsi 3:0:0:0: Direct-Access ATA ST31000525SV CV11 PQ: 0 ANSI: 5
[ra_145_82]$
[ra_145_82]$
[ra_145_82]$
[ra_145_82]$
[ra_145_82]$
[ra_145_82]$ 00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_sff_flush_pio_task: ENTER
ata_eh_link_autopsy: ENTER
ata_eh_link_autopsy: EXIT
ata4: exception Emask 0x10 SAct 0x0 SErr 0x180000 action 0x6 frozen
ata4: edma_err_cause=00000020 pp_flags=00000000, SError=00180000
ata4: SError: { 10B8B Dispar }
ata_eh_recover: ENTER
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link down (SStatus 0 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata_eh_revalidate_and_attach: EXIT rc=-5
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata4: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata4: cmd 0x27
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x407f 93==0x0000
ata_dev_set_xfermode: set features - xfer mode
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x3 nsect 0x46 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEF
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dev_set_xfermode: EXIT, err_mask=0
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata4: cmd 0x27
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x407f 93==0x0000
ata_dev_set_mode: xfer_shift=12, xfer_mode=0x46
ata4.00: configured for UDMA/133
ata_eh_recover: EXIT, rc=0
ata4: EH complete
ata_scsi_error: EXIT
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_sff_flush_pio_task: ENTER
ata_eh_link_autopsy: ENTER
ata4.00: limiting speed to UDMA/100:PIO4
ata_eh_link_autopsy: EXIT
ata4: exception Emask 0x10 SAct 0x0 SErr 0x180000 action 0x6 frozen
ata4: edma_err_cause=00000020 pp_flags=00000000, SError=00180000
ata4: SError: { 10B8B Dispar }
ata_eh_recover: ENTER
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link down (SStatus 0 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata_eh_revalidate_and_attach: EXIT rc=-5
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata4: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata4: cmd 0x27
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x407f 93==0x0000
ata_dev_set_xfermode: set features - xfer mode
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x3 nsect 0x45 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEF
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dev_set_xfermode: EXIT, err_mask=0
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata4: cmd 0x27
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x207f 93==0x0000
ata_dev_set_mode: xfer_shift=12, xfer_mode=0x45
ata4.00: configured for UDMA/100
ata_eh_recover: EXIT, rc=0
ata4: EH complete
ata_scsi_error: EXIT
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_sff_flush_pio_task: ENTER
ata_eh_link_autopsy: ENTER
ata4.00: limiting speed to UDMA/33:PIO4
ata_eh_link_autopsy: EXIT
ata4: exception Emask 0x10 SAct 0x0 SErr 0x180000 action 0x6 frozen
ata4: edma_err_cause=00000020 pp_flags=00000000, SError=00180000
ata4: SError: { 10B8B Dispar }
ata_eh_recover: ENTER
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata4: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
00040015
__ata_port_freeze: ata4 port frozen
ata_sff_flush_pio_task: ENTER
ata4.00: failed to IDENTIFY (I/O error, err_mask=0x100)
ata4.00: revalidation failed (errno=-5)
ata_eh_revalidate_and_attach: EXIT rc=-5
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata4: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata4: cmd 0x27
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x207f 93==0x0000
ata_dev_set_xfermode: set features - xfer mode
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x3 nsect 0x42 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEF
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dev_set_xfermode: EXIT, err_mask=0
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata4: cmd 0x27
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_mode: xfer_shift=12, xfer_mode=0x42
ata4.00: configured for UDMA/33
ata_eh_recover: EXIT, rc=0
ata4: EH complete
ata_scsi_error: EXIT
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_sff_flush_pio_task: ENTER
ata_eh_link_autopsy: ENTER
ata_eh_link_autopsy: EXIT
ata4: exception Emask 0x10 SAct 0x0 SErr 0x180000 action 0x6 frozen
ata4: edma_err_cause=00000020 pp_flags=00000000, SError=00180000
ata4: SError: { 10B8B Dispar }
ata_eh_recover: ENTER
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata4: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040055
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link down (SStatus 0 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata_eh_revalidate_and_attach: EXIT rc=-5
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata4: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata4: cmd 0x27
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_xfermode: set features - xfer mode
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x3 nsect 0x42 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEF
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dev_set_xfermode: EXIT, err_mask=0
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata4: cmd 0x27
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_mode: xfer_shift=12, xfer_mode=0x42
ata4.00: configured for UDMA/33
ata_eh_recover: EXIT, rc=0
ata4: EH complete
ata_scsi_error: EXIT
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_sff_flush_pio_task: ENTER
ata_eh_link_autopsy: ENTER
ata_eh_link_autopsy: EXIT
ata4: exception Emask 0x10 SAct 0x0 SErr 0x180000 action 0x6 frozen
ata4: edma_err_cause=00000020 pp_flags=00000000, SError=00180000
ata4: SError: { 10B8B Dispar }
ata_eh_recover: ENTER
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata4: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040055
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link down (SStatus 0 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata_eh_revalidate_and_attach: EXIT rc=-5
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata4: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata4: cmd 0x27
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_xfermode: set features - xfer mode
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x3 nsect 0x42 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEF
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dev_set_xfermode: EXIT, err_mask=0
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata4: cmd 0x27
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_mode: xfer_shift=12, xfer_mode=0x42
ata4.00: configured for UDMA/33
ata_eh_recover: EXIT, rc=0
ata4: EH complete
ata_scsi_error: EXIT
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_sff_flush_pio_task: ENTER
ata_eh_link_autopsy: ENTER
ata_eh_link_autopsy: EXIT
ata4: exception Emask 0x10 SAct 0x0 SErr 0x180000 action 0x6 frozen
ata4: edma_err_cause=00000020 pp_flags=00000000, SError=00180000
ata4: SError: { 10B8B Dispar }
ata_eh_recover: ENTER
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link down (SStatus 0 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata_eh_revalidate_and_attach: EXIT rc=-5
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata4: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata4: cmd 0x27
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_xfermode: set features - xfer mode
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x3 nsect 0x42 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEF
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dev_set_xfermode: EXIT, err_mask=0
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata4: cmd 0x27
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_mode: xfer_shift=12, xfer_mode=0x42
ata4.00: configured for UDMA/33
ata_eh_recover: EXIT, rc=0
ata4: EH complete
ata_scsi_error: EXIT
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_sff_flush_pio_task: ENTER
ata_eh_link_autopsy: ENTER
ata_eh_link_autopsy: EXIT
ata4: exception Emask 0x10 SAct 0x0 SErr 0x180000 action 0x6 frozen
ata4: edma_err_cause=00000020 pp_flags=00000000, SError=00180000
ata4: SError: { 10B8B Dispar }
ata_eh_recover: ENTER
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata4: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata4: cmd 0x27
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_xfermode: set features - xfer mode
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x3 nsect 0x42 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEF
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dev_set_xfermode: EXIT, err_mask=0
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata4: cmd 0x27
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_mode: xfer_shift=12, xfer_mode=0x42
ata4.00: configured for UDMA/33
ata_eh_recover: EXIT, rc=0
ata4: EH complete
ata_scsi_error: EXIT
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_sff_flush_pio_task: ENTER
ata_eh_link_autopsy: ENTER
ata_eh_link_autopsy: EXIT
ata4: exception Emask 0x10 SAct 0x0 SErr 0x180000 action 0x6 frozen
ata4: edma_err_cause=00000020 pp_flags=00000000, SError=00180000
ata4: SError: { 10B8B Dispar }
ata_eh_recover: ENTER
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata4: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata4: cmd 0x27
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_xfermode: set features - xfer mode
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x3 nsect 0x42 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEF
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dev_set_xfermode: EXIT, err_mask=0
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata4: cmd 0x27
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_mode: xfer_shift=12, xfer_mode=0x42
ata4.00: configured for UDMA/33
ata_eh_recover: EXIT, rc=0
ata4: EH complete
ata_scsi_error: EXIT
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_sff_flush_pio_task: ENTER
ata_eh_link_autopsy: ENTER
ata_eh_link_autopsy: EXIT
ata4: exception Emask 0x10 SAct 0x0 SErr 0x180000 action 0x6 frozen
ata4: edma_err_cause=00000020 pp_flags=00000000, SError=00180000
ata4: SError: { 10B8B Dispar }
ata_eh_recover: ENTER
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata4: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata4: cmd 0x27
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_xfermode: set features - xfer mode
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x3 nsect 0x42 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEF
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dev_set_xfermode: EXIT, err_mask=0
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata4: cmd 0x27
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_mode: xfer_shift=12, xfer_mode=0x42
ata4.00: configured for UDMA/33
ata_eh_recover: EXIT, rc=0
ata4: EH complete
ata_scsi_error: EXIT
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_sff_flush_pio_task: ENTER
ata_eh_link_autopsy: ENTER
ata_eh_link_autopsy: EXIT
ata4: exception Emask 0x10 SAct 0x0 SErr 0x180000 action 0x6 frozen
ata4: edma_err_cause=00000020 pp_flags=00000000, SError=00180000
ata4: SError: { 10B8B Dispar }
ata_eh_recover: ENTER
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata4: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata4: cmd 0x27
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_xfermode: set features - xfer mode
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x3 nsect 0x42 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEF
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dev_set_xfermode: EXIT, err_mask=0
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata4: cmd 0x27
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_mode: xfer_shift=12, xfer_mode=0x42
ata4.00: configured for UDMA/33
ata_eh_recover: EXIT, rc=0
ata4: EH complete
ata_scsi_error: EXIT
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_sff_flush_pio_task: ENTER
ata_eh_link_autopsy: ENTER
ata_eh_link_autopsy: EXIT
ata4: exception Emask 0x10 SAct 0x0 SErr 0x180000 action 0x6 frozen
ata4: edma_err_cause=00000020 pp_flags=00000000, SError=00180000
ata4: SError: { 10B8B Dispar }
ata_eh_recover: ENTER
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata4: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata4: cmd 0x27
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_xfermode: set features - xfer mode
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x3 nsect 0x42 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEF
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dev_set_xfermode: EXIT, err_mask=0
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata4: cmd 0x27
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_mode: xfer_shift=12, xfer_mode=0x42
ata4.00: configured for UDMA/33
ata_eh_recover: EXIT, rc=0
ata4: EH complete
ata_scsi_error: EXIT
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_sff_flush_pio_task: ENTER
ata_eh_link_autopsy: ENTER
ata_eh_link_autopsy: EXIT
ata4: exception Emask 0x10 SAct 0x0 SErr 0x180000 action 0x6 frozen
ata4: edma_err_cause=00000020 pp_flags=00000000, SError=00180000
ata4: SError: { 10B8B Dispar }
ata_eh_recover: ENTER
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata4: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: hob: feat 0x0 nsect 0x0, lba 0x0 0x0 0x0
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xE0
ata_sff_exec_command: ata4: cmd 0x27
00040015
__ata_port_freeze: ata4 port frozen
ata_sff_flush_pio_task: ENTER
ata4.00: failed to read native max address (err_mask=0x1)
ata4.00: HPA support seems broken, skipping HPA handling
ata4.00: revalidation failed (errno=-5)
ata_eh_revalidate_and_attach: EXIT rc=-5
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata4: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_xfermode: set features - xfer mode
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x3 nsect 0x42 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEF
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dev_set_xfermode: EXIT, err_mask=0
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_mode: xfer_shift=12, xfer_mode=0x42
ata4.00: configured for UDMA/33
ata_eh_recover: EXIT, rc=0
ata4: EH complete
ata_scsi_error: EXIT
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_sff_flush_pio_task: ENTER
ata_eh_link_autopsy: ENTER
ata_eh_link_autopsy: EXIT
ata4: exception Emask 0x10 SAct 0x0 SErr 0x180000 action 0x6 frozen
ata4: edma_err_cause=00000020 pp_flags=00000000, SError=00180000
ata4: SError: { 10B8B Dispar }
ata_eh_recover: ENTER
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata4: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_xfermode: set features - xfer mode
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x3 nsect 0x42 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEF
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dev_set_xfermode: EXIT, err_mask=0
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_mode: xfer_shift=12, xfer_mode=0x42
ata4.00: configured for UDMA/33
ata_eh_recover: EXIT, rc=0
ata4: EH complete
ata_scsi_error: EXIT
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_sff_flush_pio_task: ENTER
ata_eh_link_autopsy: ENTER
ata_eh_link_autopsy: EXIT
ata4: exception Emask 0x10 SAct 0x0 SErr 0x180000 action 0x6 frozen
ata4: edma_err_cause=00000020 pp_flags=00000000, SError=00180000
ata4: SError: { 10B8B Dispar }
ata_eh_recover: ENTER
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata4: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_xfermode: set features - xfer mode
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x3 nsect 0x42 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEF
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dev_set_xfermode: EXIT, err_mask=0
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_mode: xfer_shift=12, xfer_mode=0x42
ata4.00: configured for UDMA/33
ata_eh_recover: EXIT, rc=0
ata4: EH complete
ata_scsi_error: EXIT
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_sff_flush_pio_task: ENTER
ata_eh_link_autopsy: ENTER
ata_eh_link_autopsy: EXIT
ata4: exception Emask 0x10 SAct 0x0 SErr 0x180000 action 0x6 frozen
ata4: edma_err_cause=00000020 pp_flags=00000000, SError=00180000
ata4: SError: { 10B8B Dispar }
ata_eh_recover: ENTER
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata4: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_xfermode: set features - xfer mode
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x3 nsect 0x42 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEF
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dev_set_xfermode: EXIT, err_mask=0
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_mode: xfer_shift=12, xfer_mode=0x42
ata4.00: configured for UDMA/33
ata_eh_recover: EXIT, rc=0
ata4: EH complete
ata_scsi_error: EXIT
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_sff_flush_pio_task: ENTER
ata_eh_link_autopsy: ENTER
ata_eh_link_autopsy: EXIT
ata4: exception Emask 0x10 SAct 0x0 SErr 0x180000 action 0x6 frozen
ata4: edma_err_cause=00000020 pp_flags=00000000, SError=00180000
ata4: SError: { 10B8B Dispar }
ata_eh_recover: ENTER
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata4: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_xfermode: set features - xfer mode
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x3 nsect 0x42 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEF
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dev_set_xfermode: EXIT, err_mask=0
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_mode: xfer_shift=12, xfer_mode=0x42
ata4.00: configured for UDMA/33
ata_eh_recover: EXIT, rc=0
ata4: EH complete
ata_scsi_error: EXIT
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_sff_flush_pio_task: ENTER
ata_eh_link_autopsy: ENTER
ata_eh_link_autopsy: EXIT
ata4: exception Emask 0x10 SAct 0x0 SErr 0x180000 action 0x6 frozen
ata4: edma_err_cause=00000020 pp_flags=00000000, SError=00180000
ata4: SError: { 10B8B Dispar }
ata_eh_recover: ENTER
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata4: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_xfermode: set features - xfer mode
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x3 nsect 0x42 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEF
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dev_set_xfermode: EXIT, err_mask=0
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_mode: xfer_shift=12, xfer_mode=0x42
ata4.00: configured for UDMA/33
ata_eh_recover: EXIT, rc=0
ata4: EH complete
ata_scsi_error: EXIT
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_sff_flush_pio_task: ENTER
ata_eh_link_autopsy: ENTER
ata_eh_link_autopsy: EXIT
ata4: exception Emask 0x10 SAct 0x0 SErr 0x180000 action 0x6 frozen
ata4: edma_err_cause=00000020 pp_flags=00000000, SError=00180000
ata4: SError: { 10B8B Dispar }
ata_eh_recover: ENTER
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata4: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
00040015
__ata_port_freeze: ata4 port frozen
ata_sff_flush_pio_task: ENTER
------------[ cut here ]------------
WARNING: at drivers/ata/libata-sff.c:1053 0xc01702b0()
Modules linked in: sata_mv
Backtrace:
Function entered at [<c003466c>] from [<c0034784>]
r7:00000000 r6:c01702b0 r5:c0222698 r4:0000041d
Function entered at [<c003476c>] from [<c004052c>]
Function entered at [<c00404dc>] from [<c0040568>]
r8:df91930c r7:df918060 r6:df91930c r5:c02820cb r4:00000001
Function entered at [<c0040544>] from [<c01702b0>]
Function entered at [<c0170244>] from [<c0170d98>]
Function entered at [<c0170bf4>] from [<c0052200>]
r8:00000009 r7:df918060 r6:c024e320 r5:dfa2fd60 r4:decf6000
Function entered at [<c0051ff4>] from [<c0052530>]
Function entered at [<c0052364>] from [<c0056a2c>]
Function entered at [<c00569a8>] from [<c0042a28>]
r6:c0042a28 r5:c00569a8 r4:df82df10
---[ end trace 2776da609f64b4f9 ]---
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x7F)
ata_sff_hsm_move: ata4: protocol 2 task_state 4 (dev_stat 0x7F)
ata4.00: failed to IDENTIFY (I/O error, err_mask=0x2)
ata4.00: revalidation failed (errno=-5)
ata_eh_revalidate_and_attach: EXIT rc=-5
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata4: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_xfermode: set features - xfer mode
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x3 nsect 0x42 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEF
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dev_set_xfermode: EXIT, err_mask=0
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_mode: xfer_shift=12, xfer_mode=0x42
ata4.00: configured for UDMA/33
ata_eh_recover: EXIT, rc=0
ata4: EH complete
ata_scsi_error: EXIT
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_sff_flush_pio_task: ENTER
ata_eh_link_autopsy: ENTER
ata_eh_link_autopsy: EXIT
ata4: exception Emask 0x10 SAct 0x0 SErr 0x180000 action 0x6 frozen
ata4: edma_err_cause=00000020 pp_flags=00000000, SError=00180000
ata4: SError: { 10B8B Dispar }
ata_eh_recover: ENTER
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link down (SStatus 0 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata_eh_revalidate_and_attach: EXIT rc=-5
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata4: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_xfermode: set features - xfer mode
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x3 nsect 0x42 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEF
00040015
__ata_port_freeze: ata4 port frozen
ata_sff_flush_pio_task: ENTER
ata_dev_set_xfermode: EXIT, err_mask=1
ata4.00: failed to IDENTIFY (I/O error, err_mask=0x40)
ata4.00: revalidation failed (errno=-5)
ata4.00: limiting speed to UDMA/33:PIO3
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata4: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_xfermode: set features - xfer mode
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x3 nsect 0x42 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEF
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dev_set_xfermode: EXIT, err_mask=0
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_mode: xfer_shift=12, xfer_mode=0x42
ata4.00: configured for UDMA/33
ata_eh_recover: EXIT, rc=0
ata4: EH complete
ata_scsi_error: EXIT
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_sff_flush_pio_task: ENTER
ata_eh_link_autopsy: ENTER
ata_eh_link_autopsy: EXIT
ata4: exception Emask 0x10 SAct 0x0 SErr 0x180000 action 0x6 frozen
ata4: edma_err_cause=00000020 pp_flags=00000000, SError=00180000
ata4: SError: { 10B8B Dispar }
ata_eh_recover: ENTER
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata4: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040055
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link down (SStatus 0 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata_eh_revalidate_and_attach: EXIT rc=-5
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata4: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_xfermode: set features - xfer mode
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x3 nsect 0x42 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEF
ata_sff_hsm_move: ata4: protocol 1 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dev_set_xfermode: EXIT, err_mask=0
ata4: ata_dev_select: ENTER, device 0, wait 1
ata_sff_tf_load: feat 0x0 nsect 0x0 lba 0x0 0x0 0x0
ata_sff_tf_load: device 0xA0
ata_sff_exec_command: ata4: cmd 0xEC
ata_sff_hsm_move: ata4: protocol 2 task_state 2 (dev_stat 0x58)
ata_pio_sector: data read
ata_sff_hsm_move: ata4: protocol 2 task_state 3 (dev_stat 0x50)
ata_sff_hsm_move: ata4: dev 0 command complete, drv_stat 0x50
ata_sff_flush_pio_task: ENTER
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01f0 81==0x0029 82==0x346b 83==0x7d61 84==0x4133
ata_dump_id: 88==0x047f 93==0x0000
ata_dev_set_mode: xfer_shift=12, xfer_mode=0x42
ata4.00: configured for UDMA/33
ata_eh_recover: EXIT, rc=0
ata4: EH complete
ata_scsi_error: EXIT
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_sff_flush_pio_task: ENTER
ata_eh_link_autopsy: ENTER
ata_eh_link_autopsy: EXIT
ata4: exception Emask 0x10 SAct 0x0 SErr 0x180000 action 0x6 frozen
ata4: edma_err_cause=00000020 pp_flags=00000000, SError=00180000
ata4: SError: { 10B8B Dispar }
ata_eh_recover: ENTER
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link down (SStatus 0 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata_eh_revalidate_and_attach: EXIT rc=-5
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
00040055
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link down (SStatus 0 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata_eh_revalidate_and_attach: EXIT rc=-5
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
__ata_port_freeze: ata4 port frozen
ata4: hard resetting link
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_sff_softreset: ENTER
ata_sff_softreset: about to softreset, devmask=1
ata_bus_softreset: ata4: bus reset via SRST
ata_dev_classify: found ATA device by sig
ata_sff_softreset: EXIT, classes[0]=1 [1]=0
00040055
00040015
__ata_port_freeze: ata4 port frozen
ata_port_schedule_eh: port EH scheduled
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link down (SStatus 0 SControl 310)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata_eh_revalidate_and_attach: EXIT rc=-5
ata4.00: disabled
ata_eh_revalidate_and_attach: ENTER
ata_eh_recover: EXIT, rc=0
ata4: EH complete
ata_scsi_error: EXIT
ata_scsi_hotplug: ENTER
ata4.00: detaching (SCSI 3:0:0:0)
ata_scsi_hotplug: EXIT

Latest News at: http://www.indigovision.com/index.php/en/news.html
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Next message: Mel Gorman: "Re: [patch] mm/vmalloc: remove block allocation bitmap"
Previous message: Tejun Heo: "Re: [PATCH v2 4/7] signal: sigprocmask: narrow the scope of->siglock"
Next in thread: Tejun Heo: "Re: sata_mv port lockup on hotplug (kernel 2.6.38.2)"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]