[PATCH 09/13] mfd: add DB5500 PRCMU driver
From: Linus Walleij
Date: Sat May 21 2011 - 04:44:42 EST
From: Linus Walleij <linus.walleij@xxxxxxxxxx>
This adds the DB5500 PRCMU driver. Right now this one is pretty
restricted in functionality, exposing a simple interface to send
I2C messages.
Signed-off-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
---
arch/arm/mach-ux500/Kconfig | 1 +
arch/arm/mach-ux500/cpu.c | 3 +
drivers/mfd/Kconfig | 10 +
drivers/mfd/Makefile | 1 +
drivers/mfd/db5500-prcmu-regs.h | 115 ++++++++++
drivers/mfd/db5500-prcmu.c | 448 ++++++++++++++++++++++++++++++++++++++
include/linux/mfd/db5500-prcmu.h | 45 ++++
7 files changed, 623 insertions(+), 0 deletions(-)
create mode 100644 drivers/mfd/db5500-prcmu-regs.h
create mode 100644 drivers/mfd/db5500-prcmu.c
create mode 100644 include/linux/mfd/db5500-prcmu.h
diff --git a/arch/arm/mach-ux500/Kconfig b/arch/arm/mach-ux500/Kconfig
index 8071d27..365c4c3 100644
--- a/arch/arm/mach-ux500/Kconfig
+++ b/arch/arm/mach-ux500/Kconfig
@@ -12,6 +12,7 @@ menu "Ux500 SoC"
config UX500_SOC_DB5500
bool "DB5500"
+ select MFD_DB5500_PRCMU
config UX500_SOC_DB8500
bool "DB8500"
diff --git a/arch/arm/mach-ux500/cpu.c b/arch/arm/mach-ux500/cpu.c
index 11360f7..1da23bb 100644
--- a/arch/arm/mach-ux500/cpu.c
+++ b/arch/arm/mach-ux500/cpu.c
@@ -9,6 +9,7 @@
#include <linux/io.h>
#include <linux/clk.h>
#include <linux/mfd/db8500-prcmu.h>
+#include <linux/mfd/db5500-prcmu.h>
#include <asm/cacheflush.h>
#include <asm/hardware/cache-l2x0.h>
@@ -49,6 +50,8 @@ void __init ux500_init_irq(void)
* Init clocks here so that they are available for system timer
* initialization.
*/
+ if (cpu_is_u5500())
+ db5500_prcmu_early_init();
if (cpu_is_u8500())
prcmu_early_init();
clk_init();
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 7eaeb97..481770a 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -585,6 +585,16 @@ config MFD_DB8500_PRCMU
system controller running an XP70 microprocessor, which is accessed
through a register map.
+config MFD_DB5500_PRCMU
+ bool "ST-Ericsson DB5500 Power Reset Control Management Unit"
+ depends on UX500_SOC_DB5500
+ select MFD_CORE
+ help
+ Select this option to enable support for the DB5500 Power Reset
+ and Control Management Unit. This is basically an autonomous
+ system controller running an XP70 microprocessor, which is accessed
+ through a register map.
+
config MFD_CS5535
tristate "Support for CS5535 and CS5536 southbridge core functions"
select MFD_CORE
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 814c57a..24aa444 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -79,6 +79,7 @@ obj-$(CONFIG_AB8500_GPADC) += ab8500-gpadc.o
obj-$(CONFIG_MFD_DB8500_PRCMU) += db8500-prcmu.o
# ab8500-i2c need to come after db8500-prcmu (which provides the channel)
obj-$(CONFIG_AB8500_I2C_CORE) += ab8500-i2c.o
+obj-$(CONFIG_MFD_DB5500_PRCMU) += db5500-prcmu.o
obj-$(CONFIG_MFD_TIMBERDALE) += timberdale.o
obj-$(CONFIG_PMIC_ADP5520) += adp5520.o
obj-$(CONFIG_LPC_SCH) += lpc_sch.o
diff --git a/drivers/mfd/db5500-prcmu-regs.h b/drivers/mfd/db5500-prcmu-regs.h
new file mode 100644
index 0000000..9a8e9e4
--- /dev/null
+++ b/drivers/mfd/db5500-prcmu-regs.h
@@ -0,0 +1,115 @@
+/*
+ * Copyright (C) STMicroelectronics 2009
+ * Copyright (C) ST-Ericsson SA 2010
+ *
+ * Author: Kumar Sanghvi <kumar.sanghvi@xxxxxxxxxxxxxx>
+ * Author: Sundar Iyer <sundar.iyer@xxxxxxxxxxxxxx>
+ *
+ * License Terms: GNU General Public License v2
+ *
+ * PRCM Unit registers
+ */
+
+#ifndef __MACH_PRCMU_REGS_H
+#define __MACH_PRCMU_REGS_H
+
+#include <mach/hardware.h>
+
+#define PRCM_ARM_PLLDIVPS (_PRCMU_BASE + 0x118)
+#define PRCM_ARM_PLLDIVPS_ARM_BRM_RATE 0x3f
+#define PRCM_ARM_PLLDIVPS_MAX_MASK 0xf
+
+#define PRCM_PLLARM_LOCKP (_PRCMU_BASE + 0x0a8)
+#define PRCM_PLLARM_LOCKP_PRCM_PLLARM_LOCKP3 0x2
+
+#define PRCM_ARM_CHGCLKREQ (_PRCMU_BASE + 0x114)
+#define PRCM_ARM_CHGCLKREQ_PRCM_ARM_CHGCLKREQ 0x1
+
+#define PRCM_PLLARM_ENABLE (_PRCMU_BASE + 0x98)
+#define PRCM_PLLARM_ENABLE_PRCM_PLLARM_ENABLE 0x1
+#define PRCM_PLLARM_ENABLE_PRCM_PLLARM_COUNTON 0x100
+
+#define PRCM_ARMCLKFIX_MGT (_PRCMU_BASE + 0x0)
+#define PRCM_A9_RESETN_CLR (_PRCMU_BASE + 0x1f4)
+#define PRCM_A9_RESETN_SET (_PRCMU_BASE + 0x1f0)
+#define PRCM_ARM_LS_CLAMP (_PRCMU_BASE + 0x30c)
+#define PRCM_SRAM_A9 (_PRCMU_BASE + 0x308)
+
+/* ARM WFI Standby signal register */
+#define PRCM_ARM_WFI_STANDBY (_PRCMU_BASE + 0x130)
+#define PRCM_IOCR (_PRCMU_BASE + 0x310)
+#define PRCM_IOCR_IOFORCE 0x1
+
+/* CPU mailbox registers */
+#define PRCM_MBOX_CPU_VAL (_PRCMU_BASE + 0x0fc)
+#define PRCM_MBOX_CPU_SET (_PRCMU_BASE + 0x100)
+#define PRCM_MBOX_CPU_CLR (_PRCMU_BASE + 0x104)
+
+/* Dual A9 core interrupt management unit registers */
+#define PRCM_A9_MASK_REQ (_PRCMU_BASE + 0x328)
+#define PRCM_A9_MASK_REQ_PRCM_A9_MASK_REQ 0x1
+
+#define PRCM_A9_MASK_ACK (_PRCMU_BASE + 0x32c)
+#define PRCM_ARMITMSK31TO0 (_PRCMU_BASE + 0x11c)
+#define PRCM_ARMITMSK63TO32 (_PRCMU_BASE + 0x120)
+#define PRCM_ARMITMSK95TO64 (_PRCMU_BASE + 0x124)
+#define PRCM_ARMITMSK127TO96 (_PRCMU_BASE + 0x128)
+#define PRCM_POWER_STATE_VAL (_PRCMU_BASE + 0x25C)
+#define PRCM_ARMITVAL31TO0 (_PRCMU_BASE + 0x260)
+#define PRCM_ARMITVAL63TO32 (_PRCMU_BASE + 0x264)
+#define PRCM_ARMITVAL95TO64 (_PRCMU_BASE + 0x268)
+#define PRCM_ARMITVAL127TO96 (_PRCMU_BASE + 0x26C)
+
+#define PRCM_HOSTACCESS_REQ (_PRCMU_BASE + 0x334)
+#define ARM_WAKEUP_MODEM 0x1
+
+#define PRCM_ARM_IT1_CLEAR (_PRCMU_BASE + 0x48C)
+#define PRCM_ARM_IT1_VAL (_PRCMU_BASE + 0x494)
+#define PRCM_HOLD_EVT (_PRCMU_BASE + 0x174)
+
+#define PRCM_ITSTATUS0 (_PRCMU_BASE + 0x148)
+#define PRCM_ITSTATUS1 (_PRCMU_BASE + 0x150)
+#define PRCM_ITSTATUS2 (_PRCMU_BASE + 0x158)
+#define PRCM_ITSTATUS3 (_PRCMU_BASE + 0x160)
+#define PRCM_ITSTATUS4 (_PRCMU_BASE + 0x168)
+#define PRCM_ITSTATUS5 (_PRCMU_BASE + 0x484)
+#define PRCM_ITCLEAR5 (_PRCMU_BASE + 0x488)
+#define PRCM_ARMIT_MASKXP70_IT (_PRCMU_BASE + 0x1018)
+
+/* System reset register */
+#define PRCM_APE_SOFTRST (_PRCMU_BASE + 0x228)
+
+/* Level shifter and clamp control registers */
+#define PRCM_MMIP_LS_CLAMP_SET (_PRCMU_BASE + 0x420)
+#define PRCM_MMIP_LS_CLAMP_CLR (_PRCMU_BASE + 0x424)
+
+/* PRCMU clock/PLL/reset registers */
+#define PRCM_PLLDSI_FREQ (_PRCMU_BASE + 0x500)
+#define PRCM_PLLDSI_ENABLE (_PRCMU_BASE + 0x504)
+#define PRCM_PLLDSI_LOCKP (_PRCMU_BASE + 0x508)
+#define PRCM_LCDCLK_MGT (_PRCMU_BASE + 0x044)
+#define PRCM_MCDECLK_MGT (_PRCMU_BASE + 0x064)
+#define PRCM_HDMICLK_MGT (_PRCMU_BASE + 0x058)
+#define PRCM_TVCLK_MGT (_PRCMU_BASE + 0x07c)
+#define PRCM_DSI_PLLOUT_SEL (_PRCMU_BASE + 0x530)
+#define PRCM_DSITVCLK_DIV (_PRCMU_BASE + 0x52C)
+#define PRCM_PLLDSI_LOCKP (_PRCMU_BASE + 0x508)
+#define PRCM_APE_RESETN_SET (_PRCMU_BASE + 0x1E4)
+#define PRCM_APE_RESETN_CLR (_PRCMU_BASE + 0x1E8)
+#define PRCM_CLKOCR (_PRCMU_BASE + 0x1CC)
+
+/* ePOD and memory power signal control registers */
+#define PRCM_EPOD_C_SET (_PRCMU_BASE + 0x410)
+#define PRCM_SRAM_LS_SLEEP (_PRCMU_BASE + 0x304)
+
+/* Debug power control unit registers */
+#define PRCM_POWER_STATE_SET (_PRCMU_BASE + 0x254)
+
+/* Miscellaneous unit registers */
+#define PRCM_DSI_SW_RESET (_PRCMU_BASE + 0x324)
+#define PRCM_GPIOCR (_PRCMU_BASE + 0x138)
+#define PRCM_GPIOCR_DBG_STM_MOD_CMD1 0x800
+#define PRCM_GPIOCR_DBG_UARTMOD_CMD0 0x1
+
+
+#endif /* __MACH_PRCMU__REGS_H */
diff --git a/drivers/mfd/db5500-prcmu.c b/drivers/mfd/db5500-prcmu.c
new file mode 100644
index 0000000..9dbb3ca
--- /dev/null
+++ b/drivers/mfd/db5500-prcmu.c
@@ -0,0 +1,448 @@
+/*
+ * Copyright (C) ST-Ericsson SA 2010
+ *
+ * License Terms: GNU General Public License v2
+ * Author: Mattias Nilsson <mattias.i.nilsson@xxxxxxxxxxxxxx>
+ *
+ * U5500 PRCM Unit interface driver
+ */
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/errno.h>
+#include <linux/err.h>
+#include <linux/spinlock.h>
+#include <linux/io.h>
+#include <linux/slab.h>
+#include <linux/mutex.h>
+#include <linux/completion.h>
+#include <linux/irq.h>
+#include <linux/jiffies.h>
+#include <linux/bitops.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/db5500-prcmu.h>
+#include <mach/hardware.h>
+#include <mach/irqs.h>
+#include <mach/db5500-regs.h>
+#include "db5500-prcmu-regs.h"
+
+#define _PRCM_MB_HEADER (tcdm_base + 0xFE8)
+#define PRCM_REQ_MB0_HEADER (_PRCM_MB_HEADER + 0x0)
+#define PRCM_REQ_MB1_HEADER (_PRCM_MB_HEADER + 0x1)
+#define PRCM_REQ_MB2_HEADER (_PRCM_MB_HEADER + 0x2)
+#define PRCM_REQ_MB3_HEADER (_PRCM_MB_HEADER + 0x3)
+#define PRCM_REQ_MB4_HEADER (_PRCM_MB_HEADER + 0x4)
+#define PRCM_REQ_MB5_HEADER (_PRCM_MB_HEADER + 0x5)
+#define PRCM_REQ_MB6_HEADER (_PRCM_MB_HEADER + 0x6)
+#define PRCM_REQ_MB7_HEADER (_PRCM_MB_HEADER + 0x7)
+#define PRCM_ACK_MB0_HEADER (_PRCM_MB_HEADER + 0x8)
+#define PRCM_ACK_MB1_HEADER (_PRCM_MB_HEADER + 0x9)
+#define PRCM_ACK_MB2_HEADER (_PRCM_MB_HEADER + 0xa)
+#define PRCM_ACK_MB3_HEADER (_PRCM_MB_HEADER + 0xb)
+#define PRCM_ACK_MB4_HEADER (_PRCM_MB_HEADER + 0xc)
+#define PRCM_ACK_MB5_HEADER (_PRCM_MB_HEADER + 0xd)
+#define PRCM_ACK_MB6_HEADER (_PRCM_MB_HEADER + 0xe)
+#define PRCM_ACK_MB7_HEADER (_PRCM_MB_HEADER + 0xf)
+
+/* Req Mailboxes */
+#define PRCM_REQ_MB0 (tcdm_base + 0xFD8)
+#define PRCM_REQ_MB1 (tcdm_base + 0xFCC)
+#define PRCM_REQ_MB2 (tcdm_base + 0xFC4)
+#define PRCM_REQ_MB3 (tcdm_base + 0xFC0)
+#define PRCM_REQ_MB4 (tcdm_base + 0xF98)
+#define PRCM_REQ_MB5 (tcdm_base + 0xF90)
+#define PRCM_REQ_MB6 (tcdm_base + 0xF8C)
+#define PRCM_REQ_MB7 (tcdm_base + 0xF84)
+
+/* Ack Mailboxes */
+#define PRCM_ACK_MB0 (tcdm_base + 0xF38)
+#define PRCM_ACK_MB1 (tcdm_base + 0xF30)
+#define PRCM_ACK_MB2 (tcdm_base + 0xF24)
+#define PRCM_ACK_MB3 (tcdm_base + 0xF20)
+#define PRCM_ACK_MB4 (tcdm_base + 0xF1C)
+#define PRCM_ACK_MB5 (tcdm_base + 0xF14)
+#define PRCM_ACK_MB6 (tcdm_base + 0xF0C)
+#define PRCM_ACK_MB7 (tcdm_base + 0xF08)
+
+enum mb_return_code {
+ RC_SUCCESS,
+ RC_FAIL,
+};
+
+/* Mailbox 0 headers. */
+enum mb0_header {
+ /* request */
+ RMB0H_PWR_STATE_TRANS = 1,
+ RMB0H_WAKE_UP_CFG,
+ RMB0H_RD_WAKE_UP_ACK,
+ /* acknowledge */
+ AMB0H_WAKE_UP = 1,
+};
+
+/* Mailbox 5 headers. */
+enum mb5_header {
+ MB5H_I2C_WRITE = 1,
+ MB5H_I2C_READ,
+};
+
+/* Request mailbox 5 fields. */
+#define PRCM_REQ_MB5_I2C_SLAVE (PRCM_REQ_MB5 + 0)
+#define PRCM_REQ_MB5_I2C_REG (PRCM_REQ_MB5 + 1)
+#define PRCM_REQ_MB5_I2C_SIZE (PRCM_REQ_MB5 + 2)
+#define PRCM_REQ_MB5_I2C_DATA (PRCM_REQ_MB5 + 4)
+
+/* Acknowledge mailbox 5 fields. */
+#define PRCM_ACK_MB5_RETURN_CODE (PRCM_ACK_MB5 + 0)
+#define PRCM_ACK_MB5_I2C_DATA (PRCM_ACK_MB5 + 4)
+
+#define NUM_MB 8
+#define MBOX_BIT BIT
+#define ALL_MBOX_BITS (MBOX_BIT(NUM_MB) - 1)
+
+/*
+* Used by MCDE to setup all necessary PRCMU registers
+*/
+#define PRCMU_RESET_DSIPLL 0x00004000
+#define PRCMU_UNCLAMP_DSIPLL 0x00400800
+
+/* HDMI CLK MGT PLLSW=001 (PLLSOC0), PLLDIV=0x8, = 50 Mhz*/
+#define PRCMU_DSI_CLOCK_SETTING 0x00000128
+/* TVCLK_MGT PLLSW=001 (PLLSOC0) PLLDIV=0x13, = 19.05 MHZ */
+#define PRCMU_DSI_LP_CLOCK_SETTING 0x00000135
+#define PRCMU_PLLDSI_FREQ_SETTING 0x0004013C
+#define PRCMU_DSI_PLLOUT_SEL_SETTING 0x00000002
+#define PRCMU_ENABLE_ESCAPE_CLOCK_DIV 0x03000101
+#define PRCMU_DISABLE_ESCAPE_CLOCK_DIV 0x00000101
+
+#define PRCMU_ENABLE_PLLDSI 0x00000001
+#define PRCMU_DISABLE_PLLDSI 0x00000000
+
+#define PRCMU_DSI_RESET_SW 0x00000003
+
+#define PRCMU_PLLDSI_LOCKP_LOCKED 0x3
+
+/*
+ * mb0_transfer - state needed for mailbox 0 communication.
+ * @lock: The transaction lock.
+ */
+static struct {
+ spinlock_t lock;
+} mb0_transfer;
+
+/*
+ * mb5_transfer - state needed for mailbox 5 communication.
+ * @lock: The transaction lock.
+ * @work: The transaction completion structure.
+ * @ack: Reply ("acknowledge") data.
+ */
+static struct {
+ struct mutex lock;
+ struct completion work;
+ struct {
+ u8 header;
+ u8 status;
+ u8 value[4];
+ } ack;
+} mb5_transfer;
+
+/* PRCMU TCDM base IO address. */
+static __iomem void *tcdm_base;
+
+/**
+ * db5500_prcmu_abb_read() - Read register value(s) from the ABB.
+ * @slave: The I2C slave address.
+ * @reg: The (start) register address.
+ * @value: The read out value(s).
+ * @size: The number of registers to read.
+ *
+ * Reads register value(s) from the ABB.
+ * @size has to be <= 4.
+ */
+int db5500_prcmu_abb_read(u8 slave, u8 reg, u8 *value, u8 size)
+{
+ int r;
+
+ if ((size < 1) || (4 < size))
+ return -EINVAL;
+
+ mutex_lock(&mb5_transfer.lock);
+
+ while (readl(PRCM_MBOX_CPU_VAL) & MBOX_BIT(5))
+ cpu_relax();
+ writeb(slave, PRCM_REQ_MB5_I2C_SLAVE);
+ writeb(reg, PRCM_REQ_MB5_I2C_REG);
+ writeb(size, PRCM_REQ_MB5_I2C_SIZE);
+ writeb(MB5H_I2C_READ, PRCM_REQ_MB5_HEADER);
+
+ writel(MBOX_BIT(5), PRCM_MBOX_CPU_SET);
+ wait_for_completion(&mb5_transfer.work);
+
+ r = 0;
+ if ((mb5_transfer.ack.header == MB5H_I2C_READ) &&
+ (mb5_transfer.ack.status == RC_SUCCESS))
+ memcpy(value, mb5_transfer.ack.value, (size_t)size);
+ else
+ r = -EIO;
+
+ mutex_unlock(&mb5_transfer.lock);
+
+ return r;
+}
+
+/**
+ * db5500_prcmu_abb_write() - Write register value(s) to the ABB.
+ * @slave: The I2C slave address.
+ * @reg: The (start) register address.
+ * @value: The value(s) to write.
+ * @size: The number of registers to write.
+ *
+ * Writes register value(s) to the ABB.
+ * @size has to be <= 4.
+ */
+int db5500_prcmu_abb_write(u8 slave, u8 reg, u8 *value, u8 size)
+{
+ int r;
+
+ if ((size < 1) || (4 < size))
+ return -EINVAL;
+
+ mutex_lock(&mb5_transfer.lock);
+
+ while (readl(PRCM_MBOX_CPU_VAL) & MBOX_BIT(5))
+ cpu_relax();
+ writeb(slave, PRCM_REQ_MB5_I2C_SLAVE);
+ writeb(reg, PRCM_REQ_MB5_I2C_REG);
+ writeb(size, PRCM_REQ_MB5_I2C_SIZE);
+ memcpy_toio(PRCM_REQ_MB5_I2C_DATA, value, size);
+ writeb(MB5H_I2C_WRITE, PRCM_REQ_MB5_HEADER);
+
+ writel(MBOX_BIT(5), PRCM_MBOX_CPU_SET);
+ wait_for_completion(&mb5_transfer.work);
+
+ if ((mb5_transfer.ack.header == MB5H_I2C_WRITE) &&
+ (mb5_transfer.ack.status == RC_SUCCESS))
+ r = 0;
+ else
+ r = -EIO;
+
+ mutex_unlock(&mb5_transfer.lock);
+
+ return r;
+}
+
+int db5500_prcmu_enable_dsipll(void)
+{
+ int i;
+
+ /* Enable DSIPLL_RESETN resets */
+ writel(PRCMU_RESET_DSIPLL, PRCM_APE_RESETN_CLR);
+ /* Unclamp DSIPLL in/out */
+ writel(PRCMU_UNCLAMP_DSIPLL, PRCM_MMIP_LS_CLAMP_CLR);
+ /* Set DSI PLL FREQ */
+ writel(PRCMU_PLLDSI_FREQ_SETTING, PRCM_PLLDSI_FREQ);
+ writel(PRCMU_DSI_PLLOUT_SEL_SETTING,
+ PRCM_DSI_PLLOUT_SEL);
+ /* Enable Escape clocks */
+ writel(PRCMU_ENABLE_ESCAPE_CLOCK_DIV, PRCM_DSITVCLK_DIV);
+
+ /* Start DSI PLL */
+ writel(PRCMU_ENABLE_PLLDSI, PRCM_PLLDSI_ENABLE);
+ /* Reset DSI PLL */
+ writel(PRCMU_DSI_RESET_SW, PRCM_DSI_SW_RESET);
+ for (i = 0; i < 10; i++) {
+ if ((readl(PRCM_PLLDSI_LOCKP) &
+ PRCMU_PLLDSI_LOCKP_LOCKED) == PRCMU_PLLDSI_LOCKP_LOCKED)
+ break;
+ udelay(100);
+ }
+ /* Release DSIPLL_RESETN */
+ writel(PRCMU_RESET_DSIPLL, PRCM_APE_RESETN_SET);
+ return 0;
+}
+
+int db5500_prcmu_disable_dsipll(void)
+{
+ /* Disable dsi pll */
+ writel(PRCMU_DISABLE_PLLDSI, PRCM_PLLDSI_ENABLE);
+ /* Disable escapeclock */
+ writel(PRCMU_DISABLE_ESCAPE_CLOCK_DIV, PRCM_DSITVCLK_DIV);
+ return 0;
+}
+
+int db5500_prcmu_set_display_clocks(void)
+{
+ /* HDMI and TVCLK Should be handled somewhere else */
+ /* PLLDIV=8, PLLSW=2, CLKEN=1 */
+ writel(PRCMU_DSI_CLOCK_SETTING, PRCM_HDMICLK_MGT);
+ /* PLLDIV=14, PLLSW=2, CLKEN=1 */
+ writel(PRCMU_DSI_LP_CLOCK_SETTING, PRCM_TVCLK_MGT);
+ return 0;
+}
+
+static void ack_dbb_wakeup(void)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&mb0_transfer.lock, flags);
+
+ while (readl(PRCM_MBOX_CPU_VAL) & MBOX_BIT(0))
+ cpu_relax();
+
+ writeb(RMB0H_RD_WAKE_UP_ACK, PRCM_REQ_MB0_HEADER);
+ writel(MBOX_BIT(0), PRCM_MBOX_CPU_SET);
+
+ spin_unlock_irqrestore(&mb0_transfer.lock, flags);
+}
+
+static inline void print_unknown_header_warning(u8 n, u8 header)
+{
+ pr_warning("prcmu: Unknown message header (%d) in mailbox %d.\n",
+ header, n);
+}
+
+static bool read_mailbox_0(void)
+{
+ bool r;
+ u8 header;
+
+ header = readb(PRCM_ACK_MB0_HEADER);
+ switch (header) {
+ case AMB0H_WAKE_UP:
+ r = true;
+ break;
+ default:
+ print_unknown_header_warning(0, header);
+ r = false;
+ break;
+ }
+ writel(MBOX_BIT(0), PRCM_ARM_IT1_CLEAR);
+ return r;
+}
+
+static bool read_mailbox_1(void)
+{
+ writel(MBOX_BIT(1), PRCM_ARM_IT1_CLEAR);
+ return false;
+}
+
+static bool read_mailbox_2(void)
+{
+ writel(MBOX_BIT(2), PRCM_ARM_IT1_CLEAR);
+ return false;
+}
+
+static bool read_mailbox_3(void)
+{
+ writel(MBOX_BIT(3), PRCM_ARM_IT1_CLEAR);
+ return false;
+}
+
+static bool read_mailbox_4(void)
+{
+ writel(MBOX_BIT(4), PRCM_ARM_IT1_CLEAR);
+ return false;
+}
+
+static bool read_mailbox_5(void)
+{
+ u8 header;
+
+ header = readb(PRCM_ACK_MB5_HEADER);
+ switch (header) {
+ case MB5H_I2C_READ:
+ memcpy_fromio(mb5_transfer.ack.value, PRCM_ACK_MB5_I2C_DATA, 4);
+ case MB5H_I2C_WRITE:
+ mb5_transfer.ack.header = header;
+ mb5_transfer.ack.status = readb(PRCM_ACK_MB5_RETURN_CODE);
+ complete(&mb5_transfer.work);
+ break;
+ default:
+ print_unknown_header_warning(5, header);
+ break;
+ }
+ writel(MBOX_BIT(5), PRCM_ARM_IT1_CLEAR);
+ return false;
+}
+
+static bool read_mailbox_6(void)
+{
+ writel(MBOX_BIT(6), PRCM_ARM_IT1_CLEAR);
+ return false;
+}
+
+static bool read_mailbox_7(void)
+{
+ writel(MBOX_BIT(7), PRCM_ARM_IT1_CLEAR);
+ return false;
+}
+
+static bool (* const read_mailbox[NUM_MB])(void) = {
+ read_mailbox_0,
+ read_mailbox_1,
+ read_mailbox_2,
+ read_mailbox_3,
+ read_mailbox_4,
+ read_mailbox_5,
+ read_mailbox_6,
+ read_mailbox_7
+};
+
+static irqreturn_t prcmu_irq_handler(int irq, void *data)
+{
+ u32 bits;
+ u8 n;
+ irqreturn_t r;
+
+ bits = (readl(PRCM_ARM_IT1_VAL) & ALL_MBOX_BITS);
+ if (unlikely(!bits))
+ return IRQ_NONE;
+
+ r = IRQ_HANDLED;
+ for (n = 0; bits; n++) {
+ if (bits & MBOX_BIT(n)) {
+ bits -= MBOX_BIT(n);
+ if (read_mailbox[n]())
+ r = IRQ_WAKE_THREAD;
+ }
+ }
+ return r;
+}
+
+static irqreturn_t prcmu_irq_thread_fn(int irq, void *data)
+{
+ ack_dbb_wakeup();
+ return IRQ_HANDLED;
+}
+
+void __init db5500_prcmu_early_init(void)
+{
+ tcdm_base = __io_address(U5500_PRCMU_TCDM_BASE);
+ spin_lock_init(&mb0_transfer.lock);
+ mutex_init(&mb5_transfer.lock);
+ init_completion(&mb5_transfer.work);
+}
+
+/**
+ * prcmu_fw_init - arch init call for the Linux PRCMU fw init logic
+ *
+ */
+int __init db5500_prcmu_init(void)
+{
+ int r = 0;
+
+ if (ux500_is_svp() || !cpu_is_u5500())
+ return -ENODEV;
+
+ /* Clean up the mailbox interrupts after pre-kernel code. */
+ writel(ALL_MBOX_BITS, PRCM_ARM_IT1_CLEAR);
+
+ r = request_threaded_irq(IRQ_DB5500_PRCMU1, prcmu_irq_handler,
+ prcmu_irq_thread_fn, 0, "prcmu", NULL);
+ if (r < 0) {
+ pr_err("prcmu: Failed to allocate IRQ_DB5500_PRCMU1.\n");
+ return -EBUSY;
+ }
+ return 0;
+}
+
+arch_initcall(db5500_prcmu_init);
diff --git a/include/linux/mfd/db5500-prcmu.h b/include/linux/mfd/db5500-prcmu.h
new file mode 100644
index 0000000..f097798
--- /dev/null
+++ b/include/linux/mfd/db5500-prcmu.h
@@ -0,0 +1,45 @@
+/*
+ * Copyright (C) ST-Ericsson SA 2010
+ *
+ * License Terms: GNU General Public License v2
+ *
+ * U5500 PRCMU API.
+ */
+#ifndef __MACH_PRCMU_U5500_H
+#define __MACH_PRCMU_U5500_H
+
+#ifdef CONFIG_UX500_SOC_DB5500
+
+void db5500_prcmu_early_init(void);
+
+int db5500_prcmu_abb_read(u8 slave, u8 reg, u8 *value, u8 size);
+int db5500_prcmu_abb_write(u8 slave, u8 reg, u8 *value, u8 size);
+
+#else /* !CONFIG_UX500_SOC_DB5500 */
+
+static inline void db5500_prcmu_early_init(void)
+{
+}
+
+static inline int db5500_prcmu_abb_read(u8 slave, u8 reg, u8 *value, u8 size)
+{
+ return -ENOSYS;
+}
+
+static inline int db5500_prcmu_abb_write(u8 slave, u8 reg, u8 *value, u8 size)
+{
+ return -ENOSYS;
+}
+
+#endif /* CONFIG_UX500_SOC_DB5500 */
+
+static inline int db5500_prcmu_config_abb_event_readout(u32 abb_events)
+{
+#ifdef CONFIG_MACH_U5500_SIMULATOR
+ return 0;
+#else
+ return -1;
+#endif
+}
+
+#endif /* __MACH_PRCMU_U5500_H */
--
1.7.3.2
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/