Re: [PATCH 1/4 v4] drivers: create a pin control subsystem

[Linus Walleij]

On Thu, Aug 25, 2011 at 9:13 PM, Stephen Warren <swarren@xxxxxxxxxx> wrote:
> Linus Walleij wrote at Thursday, August 25, 2011 4:13 AM:
>
>> So this is radically different in that it requires the pin control
>> system to assume basically that any one pin can be used for
>> any one function.
>
> I think that's the wrong conclusion; 1:many isn't the same as 1:all/any.
> The data model might be structured to allow that, but in practice most
> HW allows 1:some_subset, not 1:all/any. I think this was well-covered in
> some other recent responses in this thread.

OK what I was mainly after was if the data model should
be structured to accept phone-exchange type muxing. If it
does and such a hardware appears - I mean a hardware where
any pin can be muxed anywhere, and given the second point
you make that the pinmux subsystem should expose all possible
combinations, it will lead to a situation where the driver
needs to expose all permutations i.e. (n over k) combinations
per function where n is the number of available pins and k
is the number of pins used by any one function. That would
just explode...

So if we assume that such a hardware does not exist but
the number of permutations of functions will always be limited,
it makes much more sense.

I'll encode this theoretical assumption in
Documentation/pinctrl.txt as I go along.

>> So the data model I'm assuming is:
>>
>> - Pins has a 1..* relation to functions
>> - Functions in general have a 1..1 relation to pins,
>> - Device drivers in general have a 1..1 relation to
>>   functions
>> - Functions with 1..* relation to pins is uncommon
>>   as is 1..* realtions between device drivers and
>>   functions.
>>
>> The latter is the crucial point where I think we have
>> different assumptions.
>
> As a few other replies pointed out, a number of chips do allow the at
> least some logical functions to be mux'd onto different pins. Tegra
> certainly isn't unique in this.

Yeah I get this now... and it's a handful of alternatives for a
few functions, sorry for being such a slow learner.

>> If it holds, it leads to the fact that a pinmux driver
>> will present a few functions for say i2s0 usually only
>> one, maybe two, three, never hundreds.
>
> Certainly I'd assume the number of pins/groups that a given function
> could be mux'd out onto is small, say 1-3. But, certainly not limited
> to just 1 in many cases.

Sure, we're on the same page. So I now need to find a
way to expose a few different localities per function from
the system and all the way to the map, and drop the string
naming system so instead of using spi0-0, spi0-1, spi0-2
I use some tuple like {"spi0", 0}, {"spi0", 1}, {"spi0", 2}
and I call the latter integer something like "locality" or
"position".

> Just a note: There are Tegra-based boards in wide use (in fact, boards
> for which some support is in mainline) that make active use of switching
> the routing of a HW function between different pins at run-time.
> Specifically, switching 1 I2C controller between 2 busses on the board.
>
> In fact, soon after the pinmux system is upstream, I hope we (NVIDIA) will
> be writing and submitting an I2C bus mux driver based on that. In our
> downstream kernels, we do this as custom code in the I2C host driver, but
> I want to move it out into a separate driver that anyone can use.

This is pretty cool and a usecase that I was thinking about. It'll
be fun!

Yours,
Linus Walleij
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/